@broly @kar200 @Lucky1 and all -
i still have this dir-3060, not well supported.
questions:
1 - can i 'convert' it to another dir-xxxx model (1360, 26600)?
2 - how to convert?
3- what's the best-supported model? it looks to me the choices are dir-1960 or dir-2660
thank you
!!!
The short answer would be "no", the longer answer would involve "doing that wouldn't improve the support status at all, otherwise it would have been done already).
well what work I did do is still setting there
but really it needs someone who has one
to polish it off & submit it into openwrt
anyone is welcome to take what's there and finish it
I'm still waiting for a really basic pull request to pass
it's been sitting there for nearly 6 months
so I have some what lost interest in doing anything atm
thanks - cloning your git now and i'll do some work
That was quick!. By the way if this will be sent for review as a pull request you "or whever is doing it" should change the led lights definitions. Remove them from leds file and add them as triggers.
i.e.
wlan2g {
label = "blue:wlan2g";
gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
linux,default-trigger = "phy0radio";
};
This phy radio worked for me although the lights do not flash and but still come on or go off if the wireless is active/inactive
@kar200 -
im just getting to building now.
where do i put the code for the led trigger?
You can have a look at the dir-853 DTS to and adapt it to yours.
You don't need it by the way it was only in case you (or someone else) tries to add it to the official openwrt.
@Lucky1 -
i cloned your git - thnk you ! - but get this error trying to make for dir-3060-A1:
Makefile 'package/feeds/packages/bluld/Makefile' has a dependency on 'kmod-leds-uleds', which does not exist
this occurs from the default config.
it builds an image without luci.
if i add luci via menuconfig opton, i can't build.
any hints?
thanks.
I'm not sure what it was but there have been a few updates
I did a quick & dirty update of the dts it compiled here ok
but I can't test it & lots changed around wifi & mac addresses
see if this helps & compare it to your own
@lucky1 -
i will give this a try. my build setup is 'not fast' and i will report as soon as i have something.
thanks so much
Hello.
Is the support topic for DIR-3060 dead or is it still valid?
this needs someone who owns a device to polish what's been done
& submit it into openwrt
if done soon it may even make V22 branch
I am currently using this router with original firmware but I have a Turris Omnia in my drawer so I can swap. I will then have a free DIR-3060 for experimentation 
Hello.
I already have this device available for testing. Where to start? Will I need to connect to the console and disassemble the devices?
Hi Dario
I don't have this device but one close
I have started to make a version
you are welcome to take what i have started and finish it if you want
best thing is to open it & get to it's console
load up the initramfs image into ram & backup you unaltered flash
i never got feed back on the last version so i don't even know if it booted
@Lucky1 - @DarioX7
i was never able to build from the git - but i have the dir-3060 and if either of you build an image i'd be happy to continue to test
thanks
as i don't have this device
it really needs someone with one to take over & polish off the device's support
SUCCES 
TIMEOUT_COUNT=10,Load address: 0x88000000
Loading: Got ARP REPLY, set server/gtwy eth addr (f4:6d:04:49:b3:21)
Got it
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###################################################
done
Bytes transferred = 6583917 (64766d hex)
LoadAddr=88000000 NetBootFileXferSize= 0064766d
..Erasing NAND Flash...
ranand_erase: start:80000, len:20000
.Writing to NAND Flash...
done
Automatic boot of image at addr 0x88000000 ...
## Booting image at 88000000 ...
Image Name: MIPS OpenWrt Linux-5.10.90
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 6583757 Bytes = 6.3 MB
Load Address: 80001000
Entry Point: 80001000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80001000) ...
## Giving linux memsize in MB, 256
Starting kernel ...
[ 0.000000] Linux version 5.10.90 (lucky@6700K) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r18589-e821849c4f) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Sat Jan 15 22:05:55 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is D-Link DIR-3060 A1
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] percpu: Embedded 15 pages/cpu s30096 r8192 d23152 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00054320
[ 0.000000] Readback ErrCtl register=00054320
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 245460K/262144K available (6664K kernel code, 621K rwdata, 1352K rodata, 4980K init, 235K bss, 16684K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x3cc/0x5e4 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns
[ 0.015859] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.033724] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.106051] pid_max: default: 32768 minimum: 301
[ 0.115365] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.129769] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.147759] rcu: Hierarchical SRCU implementation.
[ 0.157524] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.173012] smp: Bringing up secondary CPUs ...
[ 0.182577] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.182588] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.182599] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.182720] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.242931] Synchronize counters for CPU 1: done.
[ 0.304917] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.304927] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.304934] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.304981] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.363880] Synchronize counters for CPU 2: done.
[ 0.424072] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.424081] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.424089] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.424141] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.483443] Synchronize counters for CPU 3: done.
[ 0.543044] smp: Brought up 1 node, 4 CPUs
[ 0.555291] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.574796] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.588612] pinctrl core: initialized pinctrl subsystem
[ 0.600742] NET: Registered protocol family 16
[ 0.611768] cpuidle: using governor teo
[ 0.639882] random: fast init done
[ 0.660119] clocksource: Switched to clocksource GIC
[ 0.671803] NET: Registered protocol family 2
[ 0.680708] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.695828] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.712398] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.727546] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.741723] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.754451] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.767334] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.781369] NET: Registered protocol family 1
[ 0.789905] PCI: CLS 0 bytes, default 32
[ 5.378969] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 5.395715] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 5.407251] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 5.428990] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 5.440371] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 5.451648] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 5.463507] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 5.477571] printk: console [ttyS0] disabled
[ 5.486080] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 5.504021] printk: console [ttyS0] enabled
[ 5.504021] printk: console [ttyS0] enabled
[ 5.520533] printk: bootconsole [early0] disabled
[ 5.520533] printk: bootconsole [early0] disabled
[ 5.541457] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[ 5.556285] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1
[ 5.568944] nand: Winbond W29N01HV
[ 5.575721] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 5.590801] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 5.603830] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 5.618386] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 5.632952] Scanning device for bad blocks
[ 6.286261] 9 fixed-partitions partitions found on MTD device mt7621-nand
[ 6.299789] Creating 9 MTD partitions on "mt7621-nand":
[ 6.310206] 0x000000000000-0x000000080000 : "Bootloader"
[ 6.321746] 0x000000080000-0x000000100000 : "config"
[ 6.332558] 0x000000100000-0x000000140000 : "factory"
[ 6.343593] 0x000000140000-0x000000180000 : "config2"
[ 6.354558] 0x000000180000-0x000002980000 : "firmware"
[ 6.598096] 0x000002980000-0x000004980000 : "private"
[ 6.609208] 0x000004980000-0x000007180000 : "firmware2"
[ 6.620705] 0x000007180000-0x000007780000 : "mydlink"
[ 6.631721] 0x000007780000-0x000008000000 : "reserved"
[ 6.649844] libphy: Fixed MDIO Bus: probed
[ 6.691357] libphy: mdio: probed
[ 6.698582] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 6.714746] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21
[ 6.733083] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 6.746547] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 6.764151] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 6.780532] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 6.797010] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 6.809582] NET: Registered protocol family 10
[ 6.819831] Segment Routing with IPv6
[ 6.827262] NET: Registered protocol family 17
[ 6.836529] 8021q: 802.1Q VLAN Support v1.8
[ 6.848132] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 6.954758] libphy: dsa slave smi: probed
[ 6.963184] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL)
[ 6.983255] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL)
[ 7.003336] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL)
[ 7.023382] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL)
[ 7.043486] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL)
[ 7.064296] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 7.081312] DSA: tree 0 setup
[ 7.087586] rt2880-pinmux pinctrl: pcie is already enabled
[ 7.098717] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 7.112089] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff]
[ 7.129616] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000
[ 7.145918] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000
[ 7.162315] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 7.177454] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 7.192508] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 7.307155] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 7.318272] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 7.429553] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 7.443427] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 7.453139] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 7.462860] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 7.481584] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 7.494268] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 7.507971] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 7.521673] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 7.532601] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff])
[ 7.552913] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 7.564893] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 7.577378] pci 0000:00:00.0: reg 0x14: [mem 0x60200000-0x6020ffff]
[ 7.589923] pci 0000:00:00.0: supports D1
[ 7.597909] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 7.610226] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 7.622222] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 7.634709] pci 0000:00:01.0: reg 0x14: [mem 0x60210000-0x6021ffff]
[ 7.647249] pci 0000:00:01.0: supports D1
[ 7.655233] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 7.668713] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 7.680758] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 7.694804] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit]
[ 7.707449] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 7.738856] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 7.749294] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 7.761435] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 7.774960] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 7.788399] pci 0000:02:00.0: [14c3:7615] type 00 class 0x000280
[ 7.800425] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid
[ 7.814467] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit]
[ 7.827114] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 7.858544] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 7.868980] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 7.881121] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 7.894645] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 7.907866] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 7.921043] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 7.934908] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 7.948077] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 7.961947] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 7.975467] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff]
[ 7.988988] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff]
[ 8.002517] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff]
[ 8.016039] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 8.029559] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 8.043092] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit]
[ 8.057663] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 8.067552] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 8.081074] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 8.094601] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit]
[ 8.109164] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 8.119051] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 8.132573] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff]
[ 8.166021] Freeing unused kernel memory: 4980K
[ 8.175083] This architecture does not have kernel memory protection.
[ 8.187921] Run /init as init process
[ 8.195854] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control off
[ 8.692216] init: Console is alive
[ 8.699322] init: - watchdog -
[ 8.720535] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.744961] usbcore: registered new interface driver usbfs
[ 8.756093] usbcore: registered new interface driver hub
[ 8.766876] usbcore: registered new device driver usb
[ 8.787510] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 8.802596] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
[ 8.817954] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.828594] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1
[ 8.850265] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010
[ 8.868538] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 8.881110] hub 1-0:1.0: USB hub found
[ 8.888683] hub 1-0:1.0: 2 ports detected
[ 8.897323] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 8.907990] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2
[ 8.922933] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 8.935783] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 8.952722] hub 2-0:1.0: USB hub found
[ 8.960406] hub 2-0:1.0: 1 port detected
[ 8.976750] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 9.000539] init: - preinit -
/bin/board_detect: /etc/board.d/01_leds: line 35: syntax error: unexpected ")" (expecting ";;")
[ 9.286825] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.337675] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.373407] random: jshn: uninitialized urandom read (4 bytes read)
[ 9.563829] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 9.580424] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 9.580534] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 9.610862] 8021q: adding VLAN 0 to HW filter on device lan1
[ 9.624783] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 13.785482] procd: - early -
[ 13.791505] procd: - watchdog -
[ 14.360331] procd: - watchdog -
[ 14.367045] procd: - ubus -
[ 14.379637] urandom_read: 5 callbacks suppressed
[ 14.379650] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.430864] random: ubusd: uninitialized urandom read (4 bytes read)
[ 14.447052] procd: - init -
Please press Enter to activate this console.
[ 14.805225] kmodloader: loading kernel modules from /etc/modules.d/*
[ 15.021980] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
[ 15.025024] urngd: v1.0.2 started.
[ 15.036940] Backport generated by backports.git v5.15.8-1-0-g83f664bb
[ 15.078056] xt_time: kernel timezone is -0000
[ 15.141913] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22
[ 15.152721] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 15.163997] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 15.199460] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23
[ 15.210379] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 15.221749] mt7615e 0000:02:00.0: enabling device (0000 -> 0002)
[ 15.234133] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 15.234133]
[ 15.263365] random: crng init done
[ 15.270478] mt7615e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 15.270478]
[ 15.289933] PPP generic driver version 2.4.2
[ 15.294144] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 15.302193] NET: Registered protocol family 24
[ 15.315864] mt7615e 0000:02:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649
[ 15.349699] mt7615e 0000:02:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[ 15.355794] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 15.367214] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[ 44.436145] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 44.457238] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 44.473269] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 44.476784] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 44.503842] 8021q: adding VLAN 0 to HW filter on device lan1
[ 44.517874] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 44.532207] br-lan: port 1(lan1) entered blocking state
[ 44.542688] br-lan: port 1(lan1) entered disabled state
[ 44.554129] device lan1 entered promiscuous mode
[ 44.563452] device eth0 entered promiscuous mode
[ 44.600757] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 44.614880] 8021q: adding VLAN 0 to HW filter on device lan2
[ 44.629759] br-lan: port 2(lan2) entered blocking state
[ 44.640654] br-lan: port 2(lan2) entered disabled state
[ 44.652039] device lan2 entered promiscuous mode
[ 44.674291] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 44.688060] 8021q: adding VLAN 0 to HW filter on device lan3
[ 44.702681] br-lan: port 3(lan3) entered blocking state
[ 44.713193] br-lan: port 3(lan3) entered disabled state
[ 44.724835] device lan3 entered promiscuous mode
[ 44.748758] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode
[ 44.762624] 8021q: adding VLAN 0 to HW filter on device lan4
[ 44.777636] br-lan: port 4(lan4) entered blocking state
[ 44.788556] br-lan: port 4(lan4) entered disabled state
[ 44.800408] device lan4 entered promiscuous mode
[ 44.825702] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 44.839372] 8021q: adding VLAN 0 to HW filter on device wan
[ 49.731181] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 49.746239] br-lan: port 1(lan1) entered blocking state
[ 49.756762] br-lan: port 1(lan1) entered forwarding state
[ 49.771372] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
BusyBox v1.35.0 (2022-01-15 22:05:55 UTC) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r18589-e821849c4f
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------