Add support for ZyXEL Keenetic Lite III rev. A

For Developers
1

Hi everyone! This thread for discussions and a information exchange about ZyXEL Keenetic Lite III rev. A router to add official support OpenWRT.

ZyXEL Keenetic Lite III rev. A
ZyXEL Keenetic Lite III rev. A1000×1013 65.4 KB

General specification:
SoC Type: MediaTek MT7620N (580MHz)
ROM: 8 MB SPI-NOR (W25Q64FV)
RAM: 64 MB DDR (EM6AB160TSD-5G)
Switch: MediaTek MT7530
Ethernet: 5 ports - 5×100MbE (WAN, LAN1-4)
Wireless: 2.4 GHz (MediaTek RT5390): b/g/n
Buttons: 3 button (POWER, RESET, WPS)
Slide switch: 4 position (BASE, ADAPTER, BOOSTER, ACCESS POINT)
Bootloader: U-Boot 1.1.3
Power: 9 VDC, 0.6 A

2

PCB photos

front
front1920×2560 502 KB

back
back1920×2560 364 KB

3

Serial settings: 57600 8N1

UART
UART900×850 199 KB

4
OEM bootlog 
U-Boot 1.1.3 [4.0.0.3-9] (Dec 11 2015 - 19:00:40)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
============================================
Ralink UBoot Version: 4.0.0.3_NDMS
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Dec 11 2015  Time:19:00:40
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size = 64 Mbytes
 Firmware test register status: 0x00000000

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Enter boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                    0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   ZyXEL Keenetic Lite III
   Created:      2022-03-23  13:59:39 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1147510 Bytes =  1.1 MB
   Load Address: 80000000
   Entry Point:  802699f0
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 802699f0) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...
Linux version 3.4.113 (developers@ndmsystems.com) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-ndm-18 - NDMS Toolkit 1.0.0) ) #1 Tue Oct 17 19:11:50 MSK 2017
MediaTek SoC: MT7620N, RevID: 0206, RAM: DDR1, XTAL: 20MHz
CPU/OCP/SYS frequency: 580/193/193 MHz
CPU revision is: 00019650 (MIPS 24KEc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal
0x00000000 -> 0x00004000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00004000
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,57600n8 rdinit=/sbin/init
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Writing ErrCtl register=0005effa
Readback ErrCtl register=0005effa
Memory: 61664k/65536k available (2494k kernel code, 3872k reserved, 533k data, 168k init, 0k highmem)
NR_IRQS:40
console [ttyS0] enabled
Calibrating delay loop... 385.02 BogoMIPS (lpj=770048)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 120
io scheduler noop registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000c00 (irq = 20) is a 16550A
Registering NDM partitions parser
Ralink SPI flash driver, SPI clock: 24MHz
SPI flash chip: W25Q64BV (ef 40170000) (8192 Kbytes)
Bootloader is up to date
8 ndmpart partitions found on MTD device raspi
Creating 8 MTD partitions on "raspi":
0x000000000000-0x000000030000: "U-Boot"
0x000000030000-0x000000040000: "U-Config"
0x000000040000-0x000000050000: "RF-EEPROM"
0x000000050000-0x000000180000: "Kernel"
0x000000180000-0x0000007f0000: "RootFS"
mtd: device 4 (RootFS) set to be root filesystem
0x000000050000-0x0000007f0000: "Firmware"
0x0000007f0000-0x000000800000: "Config"
0x000000000000-0x000000800000: "Full"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
xt_time: kernel timezone is -0000
ubridge: Tiny bridge driver, 1.1
IPv4 over IPv4 tunneling driver
gre: GRE over IPv4 demultiplexor driver
Fast NAT loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
8021q: 802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
Freeing unused kernel memory: 168k freed
init: can't start a "mtdchk" process (could not execute: no such file or directory).
init: press Enter to activate this console.
[I] Jan  1 00:00:03 ndm: Core::Main: ***
[I] Jan  1 00:00:03 ndm: Core::Main: *** Network Device Manager v2.08(AAUQ.4)C2.
[I] Jan  1 00:00:03 ndm: Core::Main: *** Built Oct 17 2017 19:07:58.
[I] Jan  1 00:00:03 ndm: Core::Main: ***
[I] Jan  1 00:00:03 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/aead.ko.
[I] Jan  1 00:00:03 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_DSCP.ko.
[I] Jan  1 00:00:04 ndmip_gre: GRE over IPv4 tunneling driver
: Core::System::DriverManager: loading /lib/phr: module license 'Proprietary' taints kernel.
modules/3.4.113/phr: I/O peripheral driver. (C) 2013-2016, NDM Systems Inc., v2.0.6
xt_statistic.ko.phr: "kl_rf" platform driver loaded

[I] Jan  1 00:00:04 L2TP kernel driver, v1.5-1
ndm: Core::System::DriveLoad Ralink WDG Timer Module
rManager: loading /lib/modules/3.4.113/xt_CLASSIresetnds: Module loaded.
FY.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ip_gre.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ipt_ROUTE.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_length.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/phr.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_dscp.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/pppol2tp.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_hl.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/rt_timer_wdg.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/ipt_ECN.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_ecn.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_comment.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/mtdoops_proc.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/resetnds.ko.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/xt_string.ko.
[I] Jan  1 00:00:04 ndm: FileSystem::Temp: mounting /var/...
[I] Jan  1 00:00:04 ndm: Corertsoc_eth: Ethernet switch driver for Ralink SoCs
::Authenticator:rtsoc_eth: (C) 2016-2017, NDM Systems Inc., v1.1.48
 MD5 generator crtsoc_eth: MT7620 SoC, TX/RX buffers: 512/512, poll budget 32
reated.
[Irtsoc_eth: 04:bf:6d:65:5d:c0 address assigned to eth2
] Jan  1 00:00:04 ndm: Core::Authenticator: NT generator created.
[I] Jan  1 rtsoc_eth: MT7620 switch initialized
00:00:04 ndm: Core::Mode: "router" mode selected.
[I] Jan  1 00:00:04 ndm: Core::Authenticator: "readonly" tag registered.
[I] Jan  1 00:00:04 ndm: Core::System::Timezone: building a timezone list...
[I] Jan  1 00:00:04 ndm: Core::System::Timezone: scanning done, 138 timezone available.
[I] Jan  1 00:00:04 ndm: Core::System::Timezone: timezone reset to default.
[I] Jan  1 00:00:04 ndm: Telnet::Server: bruteforce detection is enabled.
[I] Jan  1 00:00:04 ndm: Ntp::Client: configuration reset.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/rtsoc_eth.ko.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Mac: backed up the default address 04:bf:6d:65:5d:c0 of "FastEthernet0" before changing.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/0": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/0": interface is up.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/0": renamed to "0".
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/1": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/1": interface is up.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/1": renamed to "1".
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/2": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/2": interface is up.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/2": renamed to "2".
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/3": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/3": interface is up.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/3": renamed to "3".
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/4": interface is down.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/4": interface is up.
[I] Jan  1 00:00:04 ndm: Network::Interface::Base: "FastEthernet0/4": renamed to "4".
Waiting for Wireless Events from interfaces...
[I] Jan  1 00:00:04 ndm: Http::Manager: bruteforce detection is enabled.
[I] Jan  1 00:00:04 ndm: Core::Authenticator: "http" tag registered.
[I] Jan  1 00:00:04 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/mt76x2_ap.ko.
MT76x2 AP Driver version: 3.0.5.0
[I] Jan  1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: PHY mode set.
[I] Jan  1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: country code set.
[I] Jan  1 00:00:05 ndm: Network::Interface::Rtx::WifiMaster: channel bandwidth settings reset to default.
[I] Jan  1 00:00:06 ndm: Network::Interface::Radio: the radio switch state is changed to off, software state is down [WifiMaster0].
[I] Jan  1 00:00:06 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint2": interface is down.
[I] Jan  1 00:00:06 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint1": interface is down.
[I] Jan  1 00:00:06 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint0": SSID reset.
[I] Jan  1 00:00:06 ndm: Network::Interface::Wifi: WPA PSK set.
[I] Jan  1 00:00:06 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint0": interface is down.
[I] Jan  1 00:00:06 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint3": interface is down.
[I] Jan  1 00:00:06 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint2": security level set to "private".
[I] Jan  1 00:00:06 ndm: Network::Interface::Base: "WifiMaster0/WifiStation0": interface is down.
[I] Jan  1 00:00:06 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint1": security level set to "private".
[I] Jan  1 00:00:06 ndm: Module::Manager: loaded 22 modules.
[I] Jan  1 00:00:06 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint3": security level set to "private".
[I] Jan  1 00:00:06 ndnproxy: ndnproxy 1.2.3b10 started.
[I] Jan  1 00:00:06 ndnproxy: PID file: /var/ndnproxymain.pid.
[I] Jan  1 00:00:06 ndnproxy: stats. file: /var/ndnproxymain.stat.
[I] Jan  1 00:00:06 ndm: Network::Interface::Radio: the radio switch state is changed to on, software state is down [WifiMaster0].
[I] Jan  1 00:00:07 ndm: FileSystem::Proc: system setting saved.
[I] Jan  1 00:00:07 ndm: Core::Syslog: last message repeated 13 times.
[I] Jan  1 03:00:07 ndm: Core::System::Timezone: timezone set to "Europe/Moscow".
[I] Feb 10 09:16:50 ndm: Core::System::Clock: system time has been changed.
[I] Feb 10 09:16:50 ndm: Core::System::Domainname: the system domain name set.
[I] Feb 10 09:16:50 ndm: Core::System::Hostname: the host name set.
[I] Feb 10 09:16:50 ndm: Ntp::Client: server "0.pool.ntp.org" has been added.
[I] Feb 10 09:16:50 ndm: Ntp::Client: server "1.pool.ntp.org" has been added.
[I] Feb 10 09:16:50 ndm: Ntp::Client: server "2.pool.ntp.org" has been added.
[I] Feb 10 09:16:50 ndm: Ntp::Client: server "3.pool.ntp.org" has been added.
[I] Feb 10 09:16:50 ndm: Command::LogResponse: applied.
[I] Feb 10 09:16:50 ndm: Core::Authenticator: user "admin" tagged with "cli".
[I] Feb 10 09:16:50 ndm: Core::Authenticator: user "admin" tagged with "http".
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/0": renamed to "0".
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/0": access mode enabled.
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/0": set access VLAN ID: 2.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/0": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/1": renamed to "1".
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/1": access mode enabled.
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/1": set access VLAN ID: 1.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/1": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/2": renamed to "2".
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/2": access mode enabled.
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/2": set access VLAN ID: 1.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/2": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/3": renamed to "3".
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/3": access mode enabled.
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/3": set access VLAN ID: 1.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/3": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/4": renamed to "4".
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/4": access mode enabled.
[I] Feb 10 09:16:50 ndm: Network::Interface::Switch: "FastEthernet0/4": set access VLAN ID: 1.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/4": interface is up.
[I] Feb 10 09:16:50 ndm: Network::Interface::Base: "FastEthernet0/Vlan1": interface is down.
[I] Feb 10 09:16:50 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan1.
[I] Feb 10 09:16:51 ndm: Network::Interface::Base: "FastEthernet0/Vlan1": description saved.
[I] Feb 10 09:16:51 ndm: Network::Interface::IP: "FastEthernet0/Vlan1": security level set to "private".
[I] Feb 10 09:16:51 ndm: Dhcp::Client: FastEthernet0/Vlan1 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:51 ndm: Dhcp::Client: FastEthernet0/Vlan1 DHCP name servers are enabled.
[I] Feb 10 09:16:51 ndm: Network::Interface::Base: "FastEthernet0/Vlan1": interface is up.
[I] Feb 10 09:16:51 ndm: Network::Interface::Base: "FastEthernet0/Vlan2": interface is down.
[I] Feb 10 09:16:51 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan2.
[I] Feb 10 09:16:52 ndm: Network::Interface::Base: "FastEthernet0/Vlan2": renamed to "ISP".
[I] Feb 10 09:16:52 ndm: Network::Interface::Base: "FastEthernet0/Vldevice eth2 entered promiscuous mode
an2": description saved.
[I] Feb 10 09:16:52 ndm: Network::Interface::IP: "FastEthernet0/Vlan2": security level set to "public".
[I] Feb 10 09:16:52 ndm: Dhcp::Client: started DHCP client on FastEthernet0/Vlan2.
[I] Feb 10 09:16:52 ndm: Dhcp::Client: FastEthernet0/Vlan2 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:52 ndm: Dhcp::Client: FastEthernet0/Vlan2 DHCP name servers are enabled.
[I] Feb 10 09:16:52 ndm: Network::Interface::IP: "FastEthernet0/Vlan2": global priority is 700.
[I] Feb 10 09:16:52 ndm: Igmp::Proxy: upstream role assigned to FastEthernet0/Vlan2.
[I] Feb 10 09:16:52 ndm: Network::Interface::Base: "FastEthernet0/Vlan2": interface is up.
[I] Feb 10 09:16:52 ndm: Network::Interface::Base: "FastEthernet0/Vlan3": interface is down.
[I] Feb 10 09:16:52 ndm: Network::Interface::Repository: created interface FastEthernet0/Vlan3.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "FastEthernet0/Vlan3": description saved.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "FastEthernet0/Vlan3": security level set to "private".
[I] Feb 10 09:16:53 ndm: Dhcp::Client: FastEthernet0/Vlan3 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: FastEthernet0/Vlan3 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "FastEthernet0/Vlan3": interface is up.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiMaster: country code set.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiMaster: "WifiMaster0": PHY mode set.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0": interface is up.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint0": renamed to "AccessPoint".
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint0": description saved.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint0": ACL type set.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint0": security level set to "private".
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::Wps: "WifiMaster0/AccessPoint0": WPS enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Wifi: WPA PSK set.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint0": wireless encryption enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint0": WPA2 algorithms enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint0 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint0 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Wireless: SSID saved.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint0": WMM extensions enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint0": interface is up.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint1": renamed to "GuestWiFi".
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint1": description saved.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint1": ACL type set.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint1": security level set to "private".
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint1 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint1 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Wireless: SSID saved.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint1": WMM extensions enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint1": interface is down.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint2": ACL type set.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint2": security level set to "private".
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint2 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint2 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint2": interface is down.
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::AccessPoint: "WifiMaster0/AccessPoint3": ACL type set.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "WifiMaster0/AccessPoint3": security level set to "private".
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint3 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/AccessPoint3 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/AccessPoint3": interface is down.
[I] Feb 10 09:16:53 ndm: Network::Interface::IP: "WifiMaster0/WifiStation0": security level set to "public".
[I] Feb 10 09:16:53 ndm: Network::Interface::Rtx::WifiStation: "WifiMaster0/WifiStation0": wireless encryption disabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/WifiStation0 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:53 ndm: Dhcp::Client: WifiMaster0/WifiStation0 DHCP name servers are enabled.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "WifiMaster0/WifiStation0": interface is down.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "Bridge0": interface is down.
[I] Feb 10 09:16:53 ndm: Network::Interface::Base: "Bridge0": interface is up.
[I] Feb 10 09:16:53 ndm: Network::Interface::Repository: created interface Bridge0.
[I] Feb 10 09:16:54 ndm: Network::Interface::Base: "Bridge0": renamed to "Home".
[I] Feb 10 0device eth2.1 entered promiscuous mode
9:16:54 ndmbr0: port 1(eth2.1) entered forwarding state
: Networbr0: port 1(eth2.1) entered forwarding state
k::Interface::BaADDRCONF(NETDEV_CHANGE): br0: link becomes ready
se: "Bridge0": description saved.
[I] Feb 10 09:16:54 evice ra0 entered promiscuous mode
mndm: Nebr0: port 2(ra0) entered forwarding state
twork::Interfacebr0: port 2(ra0) entered forwarding state
::Base: "Bridge0": interface is up.
[I] Feb 10 09:16:54 ndm: Network::Interface::Mac: backed up the default address f6:00:6d:3f:3c:d7 of "Home" before changing.
[I] Febr0: port 2(ra0) entered disabled state
b 10 09:16:54 r0: port 1(eth2.1) entered disabled state
32mndm: Network::Interface::IP: "Bridge0": interface is non-global.
[I] Feb 10 09:16:54 ndmr0: port 2(ra0) entered forwarding state
0m: kernel: br0: port 2(ra0) entered forwarding state
br0: port 2(ra0)br0: port 1(eth2.1) entered forwarding state
 entered forwardbr0: port 1(eth2.1) entered forwarding state
ing state
[I] Feb 10 09:16:54 ndm: Network::Interface::Bridge: FastEthernet0/Vlan1 inherited in Bridge0.
[I] Feb 10 09:16:55 ndm: kernel: br0: port 1(eth2.1) entered forwarding state
[I] Feb 10 09:16:55 ndm: Network::Interface::Bridge: AccessPoint included in Bridge0.
[I] Feb 10 09:16:55 ndm: Network::Interface::IP: "Bridge0": security level set to "private".
[I] Feb 10 09:16:55 ndm: Network::Interface::IP: "Bridge0": IP address is 192.168.1.1/24.
[I] Feb 10 09:16:55 ndm: Dhcp::Client: Bridge0 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:55 ndm: Dhcp::Client: Bridge0 DHCP name servers are enabled.
[I] Feb 10 09:16:55 ndm: Igmp::Proxy: added downstream interface Bridge0.
[I] Feb 10 09:16:55 ndm: Network::Interface::Base: "Bridge0": interface is up.
[I] Feb 10 09:16:55 ndm: Network::Interface::Base: "Bridge1": interface is down.
[I] Feb 10 09:16:55 ndm: Network::Interface::Base: "Bridge1": interface is up.
[I] Feb 10 09:16:55 ndm: Network::Interface::Repository: created interface Bridge1.
br0: port 2(ra0) entered forwarding state
br0: port 1(eth2.1) entered forwarding state
[I] Feb 10 09:16:56 ndm: Network::Interface::Base: device eth2.3 entered promiscuous mode
"Bridge1": renambr1: port 1(eth2.3) entered forwarding state
ed to "Guest".r1: port 1(eth2.3) entered forwarding state
0m
[I] Feb 10 ADDRCONF(NETDEV_CHANGE): br1: link becomes ready
09:16:56 ndm: Network::Interface::Base: "Bridge1": description saved.
[I] Febdevice ra1 entered promiscuous mode
 10 09:16:56 ndm: Network::Interface::Base: "Bridgebr1: port 1(eth2.3) entered disabled state
1": interface is up.
[I] Feb 10 09:16:56 r1: port 1(eth2.3) entered forwarding state
[32mndm: r1: port 1(eth2.3) entered forwarding state
mNetwork::Interface::Mac: backed up the default address 26:0c:aa:22:ff:7a of "Guest" before changing.
[I] Feb 10 09:16:56 ndm: Network::Interface::IP: "Bridge1": interface is non-global.
[I] Feb 10 09:16:56 ndm: kernel: br1: port 1(eth2.3) entered disabled state
[I] Feb 10 09:16:56 ndm: Network::Interface::Bridge: FastEthernet0/Vlan3 inherited in Bridge1.
[I] Feb 10 09:16:56 ndm: kernel: br1: port 1(eigmpsn: IGMP switch snooping module (C) 2015, 2016 NDM Systems Inc., v4.0.34
th2.3) entered forwarding state
[I] Feb 10 09:16:56 ndm: Network::Interface::Bridge: GuestWiFi included in Bridge1.
[I] Feb 10 09:16:56 ndm: Network::Interface::IP: "Bridge1": security level set to "protected".
[I] Feb 10 09:16:56 ndm: Network::Interface::IP: "Bridge1": IP address is 10.1.30.1/24.
[I] Feb 10 09:16:56 ndm: Dhcp::Client: Bridge1 DHCP client DNS host routes are enabled.
[I] Feb 10 09:16:56 ndm: Dhcp:br0: port 2(ra0) entered disabled state
:Client: Bridge1 DHCP name servers are enabled.
[I] Feb 10 09:16:56 ndm: Network::Interface::Base: "Bridge1": interface is up.
[I] Feb 10 09:16:56 ndm: Dhcp::Pool: pool "_WEBADMIN" range has been saved.
[I] Feb 10 09:16:56 ndm: Dhcp::Server: pool "_WEBADMIN" bound to interface Home.
[I] Feb 10 09:16:56 ndm: Dhcp::Server: pool "_WEBADMIN" is enabled.
[I] Feb 10 09:16:56 ndm: Dhcp::Pool: pool "_WEBADMIN_GUEST_AP" range has been saved.
[I] Feb 10 09:16:56 ndm: Dhcp::Server: pool "_WEBADMIN_GUEST_AP" bound to interface Guest.
[I] Feb 10 09:16:56 ndm: Dhcp::Server: pool "_WEBADMIN_GUEST_AP" is enabled.
[I] Feb 10 09:16:56 ndm: Http::Manager: security level unchanged.
[I] Feb 10 09:16:56 ndm: Http::Manager: bruteforce detection is reconfigured.
[I] Feb 10 09:16:56 ndm: Command::LogResponse: NAT rule added.
[I] Feb 10 09:16:56 ndm: Command::LogResponse: NAT rule added.
[I] Feb 10 09:16:56 ndm: Telnet::Server: security level unchanged.
[I] Feb 10 09:16:56 ndm: Telnet::Server: bruteforce detection is reconfigured.
[I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::Ppe: software PPE enabled.
[I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::Ppe: hardware PPE enabled.
[I] Feb 10 09:16:56 ndm: UPnP::Manager: using LAN interface: Bridge0.
[I] Feb 10 09:16:56 ndm: Dhcp::Server: service enabled.
[I] Feb 10 09:16:56 ndm: Dns::Manager: DNS proxy enabled.
[I] Feb 10 09:16:56 ndm: Igmp::Proxy: IGMP proxy enabled.
[I] Feb 10 09:16:56 ndm: Http::Manager: HTTP service was enabled.
[I] Feb 10 09:16:56 ndm: Telnet::Server: telnet server enabled.
[I] Feb 10 09:16:56 ndm: Ntp::Client: NTP client enabled.
[I] Feb 10 09:16:56 ndm: Core::Init: system ready, core startup time is 13 seconds.
[I] Feb 10 09:16:56 ndm: Hotspot::Discovery::Explorer: Interface Bridge1 neighbour explorer started.
[I] Feb 10 09:16:56 ndm: Hotspot::Discovery::Explorer: Interface Bridge0 neighbour explorer started.
[I] Feb 10 09:16:56 ndm: Core::System::DriverManager: loading /lib/modules/3.4.113/igmpsn.ko.
[I] Feb 10 09:16:56 ndm: Network::Interface::Rtx::WifiMaster: "WifiMaster0": auto channel mode set.
br1: port 1(eth2.3) entered forwarding state
[I] Feb 10 09:16:57 ndmbr0: port 2(ra0) entered forwarding state
: Ntp::Clienbr0: port 2(ra0) entered forwarding state
t: unable to communicate with "1.pool.ntp.org".
[I] Feb 10 09:16:57 ndm: Ntp::Client: could not synchronize, waiting...
[I] Feb 10 09:16:57 ndm: kernel: bRalink/MTK HW NAT 5.0.2.0-5 Module Enabled, FoE Size: 16384
r0: port 2(ra0) entered forwarding state
[I] Feb 10 09:16:SWNAT sizeof(bind) = 200
57 ndm:SWNAT sizeof(hashent) = 56
 Core::System::DriverManager: loading /lib/mSWNAT is registered
odules/3.4.113/hSWNAT enabled
w_nat.ko.
SWNAT caps: L2TP, PPTP, PPPoE, IPoE, MC, USB CDC/DSL[I] Feb 10 09:16
Fast VPN init, v4.0-86-5
:57 ndmPPPoE/IPoE LAN software acceleration is disabled
: Core::System::DriverManager: loading /lib/modules/3.4.113/fastvpn.ko.
[I] Feb 10 09:16:58 ndm: Http::Manager: new Web server configuration was applied.
br0: port 2(ra0) entered forwarding state
[I] Feb 10 09:16:58 ndhcps: _WEBADMIN: NDM DHCP server (version 3.1.14) started.
[I] Feb 10 09:16:58 telnetd: waiting for connections...
[I] Feb 10 09:16:58 ndm: Core::Server: started Session /var/run/ndm.core.socket.
[I] Feb 10 09:16:58 ndm: Core::Server: client disconnected.
[I] Feb 10 09:16:58 ndhcps: _WEBADMIN_GUEST_AP: NDM DHCP server (version 3.1.14) started.
[I] Feb 10 09:16:58 ndm: Core::Server: started Session /var/run/ndm.core.socket.
[I] Feb 10 09:16:58 ndm: Core::Server: client disconnected.
[I] Feb 10 09:16:58 nimproxy: NDM IGMP/Multicast proxy (version 0.0.25) started.
nginx: no NDM ACL support
ACS result: primary channel 9, 40 MHz spectrum min dirty (with CCA) = 717
[I] Feb 10 09:17:04 wmond: WifiMaster0/AccessPoint0: (MT76x2) BSS(ra0) channel switched to 9.
[I] Feb 10 09:17:09 ndm: Ntp::Client: unable to communicate with "2.pool.ntp.org".
[I] Feb 10 09:17:09 ndm: Ntp::Client: could not synchronize, waiting...
[I] Feb 10 09:17:21 ndm: Ntp::Client: unable to communicate with "3.pool.ntp.org".
[I] Feb 10 09:17:21 ndm: Ntp::Client: could not synchronize, waiting...
5
OpenWRT bootlog 

U-Boot 1.1.3 [4.0.0.3-9] (Dec 11 2015 - 19:00:40)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. SSC disabled.
spi_wait_nsec: 29
spi device id: ef 40 17 0 0 (40170000)
find flash: W25Q64BV
============================================
Ralink UBoot Version: 4.0.0.3_NDMS
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Dec 11 2015  Time:19:00:40
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 580 MHZ ####
 estimate memory size = 64 Mbytes
 Firmware test register status: 0x00000000

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Enter boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   MIPS OpenWrt Linux-5.15.94
   Created:      2023-03-01  14:37:21 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    2310015 Bytes =  2.2 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 5.15.94 (user@debian) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.2.0 r22153-107f7374c9) 12.2.0, GNU ld (GNU Binutils) 2.39) #0 Wed Mar 1 14:37:21 2023
[    0.000000] Board has DDR1
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[    0.000000] MIPS: machine is ZyXEL Keenetic Lite III (rev. A)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=0006abff
[    0.000000] Readback ErrCtl register=0006abff
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 56032K/65536K available (5592K kernel code, 601K rwdata, 1188K rodata, 1184K init, 215K bss, 9504K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] CPU Clock: 580MHz
[    0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[    0.000000] systick: enable autosleep mode
[    0.000000] systick: running - mult: 214748, shift: 32
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015577] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087805] pid_max: default: 32768 minimum: 301
[    0.097247] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.111684] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.129937] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.148687] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.168183] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.181782] pinctrl core: initialized pinctrl subsystem
[    0.193281] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.223519] rt2880_gpio 10000600.gpio: registering 24 gpios
[    0.234582] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[    0.247241] rt2880_gpio 10000638.gpio: registering 16 gpios
[    0.258265] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[    0.270843] rt2880_gpio 10000688.gpio: registering 1 gpios
[    0.281679] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[    0.295914] clocksource: Switched to clocksource systick
[    0.307497] NET: Registered PF_INET protocol family
[    0.317430] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.332534] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.349124] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.364445] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.379691] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.393713] TCP: Hash tables configured (established 1024 bind 1024)
[    0.406490] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.419409] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.433591] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.444811] PCI: CLS 0 bytes, default 32
[    0.452758] rt-timer 10000100.timer: maximum frequency is 1220Hz
[    0.469211] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    0.487705] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.499222] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.521851] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.535578] printk: console [ttyS0] disabled
[    0.544086] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[    0.563741] printk: console [ttyS0] enabled
[    0.563741] printk: console [ttyS0] enabled
[    0.580306] printk: bootconsole [early0] disabled
[    0.580306] printk: bootconsole [early0] disabled
[    0.613144] spi spi0.0: force spi mode3
[    0.622434] spi-nor spi0.0: s25fl064k (8192 Kbytes)
[    0.632319] 6 fixed-partitions partitions found on MTD device spi0.0
[    0.645042] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    0.659663] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    0.674562] Creating 6 MTD partitions on "spi0.0":
[    0.684156] 0x000000000000-0x000000030000 : "U-Boot"
[    0.696688] 0x000000030000-0x000000040000 : "U-Config"
[    0.708276] 0x000000040000-0x000000050000 : "RF-EEPROM"
[    0.721749] 0x000000050000-0x0000007f0000 : "firmware"
[    0.733461] 2 uimage-fw partitions found on MTD device firmware
[    0.745360] Creating 2 MTD partitions on "firmware":
[    0.755270] 0x000000000000-0x000000233fbf : "kernel"
[    0.765169] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only
[    0.784672] 0x000000233fbf-0x0000007a0000 : "rootfs"
[    0.794656] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only
[    0.814232] mtd: setting mtd5 (rootfs) as root device
[    0.825437] 1 squashfs-split partitions found on MTD device rootfs
[    0.837870] 0x000000570000-0x0000007a0000 : "rootfs_data"
[    0.850819] 0x0000007f0000-0x000000800000 : "Config"
[    0.861980] 0x000000000000-0x000000800000 : "Full"
[    0.904239] gsw: setting port4 to ephy mode
[    0.912801] mtk_soc_eth 10100000.ethernet: generated random MAC address 4a:01:6d:3f:2a:38
[    0.929144] mtk_soc_eth 10100000.ethernet: no mdio-bus child node found
[    0.942334] mtk_soc_eth 10100000.ethernet: mdio-bus disabled
[    0.953838] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[    0.966423] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    0.983619] rt2880_wdt 10000120.watchdog: Initialized
[    0.995250] NET: Registered PF_INET6 protocol family
[    1.012130] Segment Routing with IPv6
[    1.019622] In-situ OAM (IOAM) with IPv6
[    1.027640] NET: Registered PF_PACKET protocol family
[    1.037822] 8021q: 802.1Q VLAN Support v1.8
[    1.062164] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[    1.082837] Freeing unused kernel image (initmem) memory: 1184K
[    1.094684] This architecture does not have kernel memory protection.
[    1.107538] Run /sbin/init as init process
[    2.104093] init: Console is alive
[    2.111536] init: - watchdog -
[    3.520794] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.629596] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.650337] init: - preinit -
[    3.734194] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[    5.599613] random: jshn: uninitialized urandom read (4 bytes read)
[    5.817991] random: jshn: uninitialized urandom read (4 bytes read)
[    6.223169] random: jshn: uninitialized urandom read (4 bytes read)
[    6.633865] random: jshn: uninitialized urandom read (4 bytes read)
[    7.176573] 8021q: adding VLAN 0 to HW filter on device eth0
[    7.201919] random: procd: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.800284] jffs2: notice: (295) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found.
[    7.833684] mount_root: switching to jffs2 overlay
[    7.851139] overlayfs: upper fs does not support tmpfile.
[    7.871958] urandom-seed: Seeding with /etc/urandom.seed
[    8.025200] procd: - early -
[    8.031426] procd: - watchdog -
[    8.400378] procd: - watchdog -
[    8.407460] procd: - ubus -
[    8.573889] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.590016] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.614131] random: ubusd: uninitialized urandom read (4 bytes read)
[    8.635406] procd: - init -
Please press Enter to activate this console.
[   10.013773] random: jshn: uninitialized urandom read (4 bytes read)
[   10.133536] random: ubusd: uninitialized urandom read (4 bytes read)
[   10.245577] kmodloader: loading kernel modules from /etc/modules.d/*
[   10.902224] urngd: jent-rng init failed, err: 2
[   10.932203] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2
[   10.947397] Backport generated by backports.git v5.15.81-1-41-g02e352527db5
[   11.588578] PPP generic driver version 2.4.2
[   11.601179] NET: Registered PF_PPPOX protocol family
[   11.653059] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "RF-EEPROM"
[   11.667910] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[   11.683395] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[   11.795546] kmodloader: done loading kernel modules from /etc/modules.d/*
[   23.436790] random: crng init done
[   23.443590] random: 88 urandom warning(s) missed due to ratelimiting
[   39.248117] 8021q: adding VLAN 0 to HW filter on device eth0
[   39.294251] device eth0 entered promiscuous mode
[   39.307779] br-lan: port 1(eth0.1) entered blocking state
[   39.318649] br-lan: port 1(eth0.1) entered disabled state
[   39.329805] device eth0.1 entered promiscuous mode
[   39.416927] br-lan: port 1(eth0.1) entered blocking state
[   39.427744] br-lan: port 1(eth0.1) entered forwarding state
[   40.257399] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.36.0 (2023-02-26 17:15:33 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r22153+3-107f7374c9
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#