Add support for WN-539N5 Aigital AC1200 Extender

For Developers
1

Hi,

just another cheap and small dual band device with 2 ethernet ports which makes it interesting for my usecases.

https://fccid.io/2AZFDWN539N5

original bootlog:


U-Boot 1.1.3 (Feb  9 2015 - 18:01:15)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: 1c, device id 70 17
Warning: un-recognized chip ID, please update bootloader!
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Feb  9 2015  Time:18:01:15
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.                     2
You choosed 3
                                                                              0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    6703551 Bytes =  6.4 MB
   Load Address: 80000000
   Entry Point:  8000c150
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c150) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #45 Tue Sep 15 20:00:43 PDT 2020

 The CPU feqenuce set to 575 MHz

 MIPS CPU sleep mode enabled.
CPU revision is: 00019655 (MIPS 24Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0000000c
Readback ErrCtl register=0000000c
Memory: 53708k/65536k available (4892k kernel code, 11828k reserved, 2231k data, 3840k init, 0k highmem)
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 54050404
RALINK_GPIOMODE = 54040404
***** Xtal 40MHz *****
start PCIe register access
RALINK_RSTCTRL = 2400000
RALINK_CLKCFG1 = fdbfffc0

*************** MT7628 PCIe RC mode *************
PCIE0 enabled
Port 0 N_FTS = 1b105000
init_rt2880pci done
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000)
pci 0000:00:00.0: BAR 9: assigned [mem 0x20000000-0x201fffff pref]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit pref] (PCI address [0x20000000-0x200fffff]
pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
pci 0000:01:00.0: BAR 2: set to [mem 0x20100000-0x20103fff 64bit pref] (PCI address [0x20100000-0x20103fff]
pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
pci 0000:01:00.0: BAR 4: set to [mem 0x20104000-0x20104fff 64bit pref] (PCI address [0x20104000-0x20104fff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [io  disabled]
pci 0000:00:00.0:   bridge window [mem disabled]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff pref]
BAR0 at slot 0 = 0
bus=0x0, slot = 0x0
res[0]->start = 0
res[0]->end = 0
res[1]->start = 20200000
res[1]->end = 2020ffff
res[2]->start = 0
res[2]->end = 0
res[3]->start = 0
res[3]->end = 0
res[4]->start = 0
res[4]->end = 0
res[5]->start = 0
res[5]->end = 0
bus=0x1, slot = 0x0
res[0]->start = 20000000
res[0]->end = 200fffff
res[1]->start = 0
res[1]->end = 0
res[2]->start = 20100000
res[2]->end = 20103fff
res[3]->start = 0
res[3]->end = 0
res[4]->start = 20104000
res[4]->end = 20104fff
res[5]->start = 0
res[5]->end = 0
Switching to clocksource Ralink Systick timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
fuse init (API version 7.15)
msgmni has been set to 104
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
brd: module loaded
flash manufacture id: 1c, device id 70 17
Warning: un-recognized chip ID, please update SPI driver!
EN25Q64(1c 30171c30) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 5 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000001000000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000803f
GMAC1_MAC_ADRL -- : 0x5d416977
Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000803f
GMAC1_MAC_ADRL -- : 0x5d416977
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
register mt_drv


=== pAd = c0282000, size = 4510560 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->PciHif.CSRBaseAddress =0xc0180000, csr_addr=0xc0180000!
RTMPInitPCIeDevice():device_id=0x7663
mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a01, pAd->ChipID=0x7663
mt7663_init()-->
<--mt7663_init()
<-- RTMPAllocTxRxRingMemory, Status=0
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
FM_OUT value: u4FmOut = 0(0x00000000)
FM_OUT value: u4FmOut = 129(0x00000081)
FM detection done! loop = 1
SR calibration value u1SrCalVal = 6
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
nf_conntrack version 0.5.0 (839 buckets, 3356 max)
matchsize=264
xt_time: kernel timezone is -0000
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Warning: unable to open an initial console.
Freeing unused kernel memory: 3840k freed
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
     __   ___  _____  _____   _  _______ ______  _____  _   ___
    |  \ /   ||  ___||  __ \ | ||  __  ||__  __||  ___|| | /  /
    |   ^    || |__  | |  \ \| || |  | |  | |   | |__  | |/  /
    |  | |   ||  ___|| |  | || || |__| |  | |   |  ___||    \
    |  | |   || |___ | |__/ /| ||  __  |  | |   | |___ | |\  \
    |__| |___||_____||_____/ |_||_|  |_|  |_|   |_____||_| \__\

                        = Everyday Genius =

init: can't log to /dev/tty5
starting pid 118, tty '/dev/ttyS1': '/sbin/getty 57600 ttyS1'


=== pAd = c0a88000, size = 1459376 ===

<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x
<-- RTMPAllocAdapterBlock, Status=0
RtmpChipOpsHook(492): Not support for HIF_MT yet!
mt7628_init()-->
mt7628_init(FW(8a00), HW(8a01), CHIPID(7628))
e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888)
mt_bcn_buf_init(218): Not support for HIF_MT yet!
<--mt7628_init()

(none) login: TX_BCN DESC a22a9000 size = 320
RX[0] DESC a22ac000 size = 1024
RX[1] DESC a22ad000 size = 1024
E2pAccessMode=0
cfg_mode=9
cfg_mode=9
wmode_band_equal(): Band Equal!
AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
LEDMethod = 1
RTMPSetDefaultChannel() : default channel to 1
load fw image from fw_header_image
AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888)
FW Version:20151201
FW Build Date:20151201183641
CmdAddressLenReq:(ret = 0)
CmdFwStartReq: override = 1, address = 1048576
CmdStartDLRsp: WiFI FW Download Success
MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC)
efuse_probe: efuse = 10000002
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4
RtmpEepromGetDefault::e2p_dafault=2
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2
NVM is FLASH mode
1. Phy Mode = 14
Country Region from e2p = ffff
tssi_1_target_pwr_g_band = 30
2. Phy Mode = 14
3. Phy Mode = 14
NICInitPwrPinCfg(11): Not support for HIF_MT yet!
NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet!
mt_mac_init()-->
MtAsicInitMac()-->
mt7628_init_mac_cr()-->
MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024!
<--mt_mac_init()
        WTBL Segment 1 info:
                MemBaseAddr/FID:0x28000/0
                EntrySize/Cnt:32/128
        WTBL Segment 2 info:
                MemBaseAddr/FID:0x40000/0
                EntrySize/Cnt:64/128
        WTBL Segment 3 info:
                MemBaseAddr/FID:0x42000/64
                EntrySize/Cnt:64/128
        WTBL Segment 4 info:
                MemBaseAddr/FID:0x44000/128
                EntrySize/Cnt:32/128
AntCfgInit(2940): Not support for HIF_MT yet!
MCS Set = ff ff 00 00 01
MtAsicSetChBusyStat(861): Not support for HIF_MT yet!
CmdSlotTimeSet:(ret = 0)
[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0
MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet!
MtAsicSetPiggyBack(796): Not support for HIF_MT yet!
reload DPD from flash , 0x9F = [c600] doReload bit7[0]
CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0
MtAsicSetTxPreamble(3026): Not support for HIF_MT yet!
The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2
MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0
ap_ftkd> Initialize FT KDP Module...
Main bssid = 80:3f:5d:41:69:77
<==== rt28xx_init, Status=0
@@@ ed_monitor_exit : ===>
@@@ ed_monitor_exit : <===
mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0
WiFi Startup Cost (ra0): 3.568s
rai0: ===> main_virtual_if_open
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
load l1profile succeed!
get_wdev_by_idx: invalid idx(0)
get_wdev_by_idx: invalid idx(0)
driver_own()::Try to Clear FW Own...
driver_own()::Success to clear FW Own
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap_2G.dat
Open file "/etc/Wireless/iNIC/iNIC_ap_2G.dat" failed!
E2pAccessMode=2
SSID[0]=Wireless-AC-5G, EdcaIdx=0
cfg_mode=14
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Equal!
[TxPower] BAND0: 100
profile: FragThreshold[0]=2346
APEdca0
APEdca1
APEdca2
APEdca3
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
rtmp_read_wds_from_file(): WDS Profile
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]
WDS-Enable mode=0
HT: WDEV[0] Ext Channel = BELOW
HT: greenap_cap = 0
WtcSetMaxStaNum: MaxStaNum:111, BssidNum:1, WdsNum:4, ApcliNum:1, MaxNumChipRept:16, MinMcastWcid:133
Top Init Done!
Use dev_alloc_skb
RX[0] DESC a202a000 size = 8192
RX[1] DESC a202c000 size = 8192
cut_through_init(): ct sw token number = 4095
cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
cut_through_token_list_init(): 8234bd08,8234bd08
cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096
cut_through_token_list_init(): 8234bd10,8234bd10
Hif Init Done!
ctl->txq = c06c9acc
ctl->rxq = c06c9ad4
ctl->ackq = c06c9adc
ctl->kickq = c06c9ae4
ctl->tx_doneq = c06c9aec
ctl->rx_doneq = c06c9af4
mt7663_fw_prepare():using E2 ROM patch
mt7663_fw_prepare():using E2 firmware
Parsing patch header
        Built date: 19050210037058b

        Platform: 7663
        HW/SW version: 0x6d702d31
        Patch version: 0x3830328a
        Target address: 0xdc000, length: 204032
patch is not ready && get semaphore success
Start address = 0xdc000, DL length = 204032, Data mode = 0x80000000
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdPatchFinishReq
EventGenericEventHandler: CMD Success
release patch semaphore
WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0
Parsing CPU 0 fw tailer
        Chip ID: 0x08
        Eco version: 0x01
        Region number: 0x03
        Format version: 0x02
        Format flag: 0x01
        Ram version: 7663mp1827
        Built date: 20190502100431
        Common crc: 0x803140b2
Parsing tailer region 0
        Decomp crc: 0x0
        Decomp size: 0x0
        Decomp block size: 0x0
        Target address: 0x112c00
        Download size: 276368
        Feature set: 0x27
Parsing tailer region 1
        Decomp crc: 0x0
        Decomp size: 0x0
        Decomp block size: 0x0
        Target address: 0x2018400
        Download size: 70656
        Feature set: 0x07
Parsing tailer region 2
        Decomp crc: 0x0
        Decomp size: 0x0
        Decomp block size: 0x0
        Target address: 0x40100000
        Download size: 14720
        Feature set: 0x07
        Release info: header tag = 0, total length = 72
        tag 1, padding length = 2, tag length = 66
        payload: t-neptune-main-mt7663-mt7626-1828-JEDI_7621_7613_AP-20190502100224
Start address = 0x112c00, DL length = 276368, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x2018400, DL length = 70656, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
Start address = 0x40100000, DL length = 14720, Data mode = 0x8000000f
EventGenericEventHandler: CMD Success
MtCmdAddressLenReq:(ret = 0)
MtCmdFwStartReq: override = 0x1, address = 0x112c00
EventGenericEventHandler: CMD Success
MCU Init Done!
efuse_probe: efuse = 511161
RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5
RtmpEepromGetDefault::e2p_dafault=1
RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1
NVM is FLASH mode. dev_idx [1] FLASH OFFSET [0x8000]
validFlashEepromID(): eeFlashId=7663, pAd->ChipID=7663
Country Region from e2p = 0
mt7663_antenna_default_reset() todo
RTMPReadTxPwrPerRate(444): Don't Support this now!
RcRadioInit(): DbdcMode=0, ConcurrentBand=1
RcRadioInit(): pRadioCtrl=83d0cd18,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf
AntCfgInit(2920): Not support for HIF_MT yet!
MtReadPwrLimitTable: RF_LOCKDOWN Feature OFF !!!
EEPROM Init Done!
mt_mac_init()-->
mt_mac_pse_init(2958): Don't Support this now!
mt7663_init_mac_cr()-->
mt7663_init_mac_cr(): TMAC_TRCR0=0x82783c92
MtAsicSetMacMaxLen(1073): Not support for HIF_MT yet!
<--mt_mac_init()
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0
MAC Init Done!
MT7663BBPInit():BBP Initialization.....
        Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2
        Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0
MT7663BBPInit() todo
PHY Init Done!
RtmpOSFileOpen(): Error 2 opening /etc/Wireless/iNIC/iNIC_ap_2G.dat
Open file "/etc/Wireless/iNIC/iNIC_ap_2G.dat" failed!
E2pAccessMode=2
SSID[0]=Wireless-AC-5G, EdcaIdx=0
cfg_mode=14
cfg_mode=14
cfg_mode=14
wmode_band_equal(): Band Equal!
[TxPower] BAND0: 100
profile: FragThreshold[0]=2346
APEdca0
APEdca1
APEdca2
APEdca3
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
rtmp_read_wds_from_file(): WDS Profile
APWdsInitialize():WdsEntry[0]
APWdsInitialize():WdsEntry[1]
APWdsInitialize():WdsEntry[2]
APWdsInitialize():WdsEntry[3]
WDS-Enable mode=0
HT: WDEV[0] Ext Channel = BELOW
HT: greenap_cap = 0
tx_pwr_comp_init():NotSupportYet!
MtCmdSetMacTxRx:(ret = 0)
asic_bss_beacon_init(): NotSupportedFunc for this arch(HIF_MT)!
AsicDisableSync(): NotSupportedFunc for this arch(HIF_MT)!
MtAsicSetRalinkBurstMode(2219): Not support for HIF_MT yet!
MtAsicSetPiggyBack(590): Not support for HIF_MT yet!
WifiFwdSet::disabled=0
AsicSetPreTbtt(): NotSupportedFunc for this arch(HIF_MT)!
ap_ftkd> Initialize FT KDP Module...
Main bssid = 00:00:00:00:00:00
AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)!
MtCmdSetMacTxRx:(ret = 0)
AsicSetRxFilter(): NotSupportedFunc for this arch(HIF_MT)!
MtCmdSetMacTxRx:(ret = 0)
INIT REDUCE TCP ACK, rai0
<==== mt_wifi_init, Status=0
MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1
MSTA_Init (1) ---> ApCli
Register MSTA IF (apclii0) , pAd->MSTANum = 1
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=2
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
WDS_Init():
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=8
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=8
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=8
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
The new WDS interface MAC = 00:00:00:00:00:00
  MacTabMatchWCID = 0
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=8
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=0, ampdu_factor=3
Total allocated 4 WDS interfaces!
WtcSetMaxStaNum: MaxStaNum:111, BssidNum:1, WdsNum:4, ApcliNum:1, MaxNumChipRept:16, MinMcastWcid:133
RedInit: set Driver/N9 RED Enable to 1.
RedInit: RED Initiailize Done.
cp_support_is_enabled: set Driver CP_SUPPORT to Mode 2.
RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP
wifi_sys_open(), wdev idx = 0
wdev_attr_update(): wdevId0 = 80:3f:5d:41:69:79
[BuildChannelList] BandIdx = 0, PhyMode = 49, ChListNum = 9:
 [RadarStateCheck] RD_NORMAL_MODE
AsicSwitchChannel(): 5G Channel:155, then must be Channel_Band:1 !!
Caller: 0x8028e654

phy_mode=49, ch=153, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
AP inf up for ra_0(func_idx) OmacIdx=0
AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn
ApAutoChannelAtBootUp----------------->
ApAutoChannelAtBootUp: AutoChannelBootup[0] = 0
ApAutoChannelAtBootUp<-----------------
 ap_run_at_boot() : ACS is disable !!
[PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0
Caller: 0x802c5940

phy_mode=49, ch=153, wdev_type=1
ht_cap: ht_cap->HtCapInfo,
ldpc=1,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=0
ht_cap: ht_cap->HtCapParm,
mdpu_density=5, ampdu_factor=3
wifi_sys_linkup(), wdev idx = 0
wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:135 for WDEV_TYPE:1
 LinkToOmacIdx = 0, LinkToWdevType = 1
bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8196
UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0
MtCmdTxPowerSKUCtrl: fgTxPowerSKUEn: 0, BandIdx: 0
MtCmdTxBfBackoffCtrl: fgTxBFBackoffEn: 0, BandIdx: 0
MtCmdTxPowerPercentCtrl: fgTxPowerPercentEn: 0, BandIdx: 0
AsicSetTxStream(): NotSupportedFunc for this arch(HIF_MT)!
AsicSetRxStream(): NotSupportedFunc for this arch(HIF_MT)!
apidx 0 for WscUUIDInit
Generate UUID for apidx(0)
Raeth v3.1 (Tasklet)

phy_tx_ring = 0x01af8000, tx_ring = 0xa1af8000

phy_rx_ring0 = 0x01afa000, rx_ring0 = 0xa1afa000
GMAC1_MAC_ADRH -- : 0x0000803f
GMAC1_MAC_ADRL -- : 0x5d416977
RT305x_ESW: Link Status Changed
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
br0: port 1(eth2.1) entering learning state
br0: port 1(eth2.1) entering learning state
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: port 2(ra0) entering learning state
device rai0 entered promiscuous mode
br0: port 3(rai0) entering learning state
br0: port 3(rai0) entering learning state
warning: `dnsmasq' uses 32-bit capabilities (legacy support in use)
br0: port 1(eth2.1) entering forwarding state
br0: port 2(ra0) entering forwarding state
br0: port 3(rai0) entering forwarding state

(none) login:
2

I have already installed a similar image to it which is basically working.


U-Boot 1.1.3 (Feb  9 2015 - 18:01:15)

Board: Ralink APSoC DRAM:  64 MB
relocate_code Pointer at: 83fb8000
flash manufacture id: 1c, device id 70 17
Warning: un-recognized chip ID, please update bootloader!
============================================
Ralink UBoot Version: 4.3.0.0
--------------------------------------------
ASIC 7628_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Feb  9 2015  Time:18:01:15
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 575 MHZ ####
 estimate memory size =64 Mbytes
RESET MT7628 PHY!!!!!!
Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.

You choosed 1
                                                                              0


1: System Load Linux to SDRAM via TFTP.
 Please Input new ones /or Ctrl-C to discard
        Input device IP (10.10.10.123) ==:10.10.10.123
        Input server IP (10.10.10.3) ==:10.10.10.3
        Input Linux Kernel filename (image.bin) ==:image.bin

 netboot_common, argc= 3

 NetTxPacket = 0x83FE4DC0

 KSEG1ADDR(NetTxPacket) = 0xA3FE4DC0

 NetLoop,call eth_halt !

 NetLoop,call eth_init !
Trying Eth0 (10/100-M)

 Waitting for RX_DMA_BUSY status Start... done


 ETH_STATE_ACTIVE!!
TFTP from server 10.10.10.3; our IP address is 10.10.10.123
Filename 'image.bin'.

 TIMEOUT_COUNT=10,Load address: 0x80a00000
Loading: checksum bad
checksum bad
checksum bad
checksum bad
checksum bad
Got ARP REPLY, set server/gtwy eth addr (10:65:30:67:b9:9c)
Got it
T #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #############################################Got ARP REQUEST, return our IP
####################
         #################
done
Bytes transferred = 5410949 (529085 hex)
NetBootFileXferSize= 00529085
Automatic boot of image at addr 0x80A00000 ...
## Booting image at 80a00000 ...
   Image Name:   MIPS OpenWrt Linux-5.10.135
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    5410885 Bytes =  5.2 MB
   Load Address: 80000000
   Entry Point:  80000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64

Starting kernel ...

[    0.000000] Linux version 5.10.135 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r20266-cf110404e3) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 Tue Aug 9 11:57:39 2022
[    0.000000] Board has DDR2
[    0.000000] Analog PMU set to hw control
[    0.000000] Digital PMU set to hw control
[    0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2
[    0.000000] printk: bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc)
[    0.000000] MIPS: machine is Wavlink WL-WN531A3
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16240
[    0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
[    0.000000] Writing ErrCtl register=0000000e
[    0.000000] Readback ErrCtl register=0000000e
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 52896K/65536K available (5686K kernel code, 623K rwdata, 1204K rodata, 4188K init, 210K bss, 12640K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS: 256
[    0.000000] intc: using register map from devicetree
[    0.000000] CPU Clock: 580MHz
[    0.000000] timer_probe: no matching timers found
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[    0.000012] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[    0.015489] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[    0.087684] pid_max: default: 32768 minimum: 301
[    0.097006] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.111339] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    0.129360] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[    0.148955] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.168332] futex hash table entries: 256 (order: -1, 3072 bytes, linear)
[    0.181842] pinctrl core: initialized pinctrl subsystem
[    0.197362] NET: Registered protocol family 16
[    0.206916] thermal_sys: Registered thermal governor 'step_wise'
[    0.322390] mt7620-pci 10140000.pcie: Port 0 N_FTS = 1b105000
[    0.495276] PCI host bridge /pcie@10140000 ranges:
[    0.504630]  MEM 0x0000000020000000..0x000000002fffffff
[    0.514933]   IO 0x0000000010160000..0x000000001016ffff
[    0.578350] PCI host bridge to bus 0000:00
[    0.586411] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
[    0.599919] pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
[    0.613504] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.626916] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.642629] pci 0000:00:00.0: [14c3:0801] type 01 class 0x060400
[    0.654458] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[    0.666831] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[    0.679293] pci 0000:00:00.0: supports D1
[    0.687106] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.700223] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.716217] pci 0000:01:00.0: [14c3:7663] type 00 class 0x000280
[    0.728038] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[    0.742272] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[    0.756548] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[    0.770946] pci 0000:01:00.0: supports D1 D2
[    0.779241] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.792379] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[    0.823422] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.836414] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.849495] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[    0.862525] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[    0.876289] pci 0000:00:00.0: BAR 9: assigned [mem 0x20000000-0x201fffff pref]
[    0.890561] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff]
[    0.903992] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
[    0.919313] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
[    0.934619] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
[    0.949922] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.959694] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff pref]
[    0.981501] clocksource: Switched to clocksource MIPS
[    0.992875] NET: Registered protocol family 2
[    1.001766] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    1.016958] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    1.033488] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.048539] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
[    1.062457] TCP: Hash tables configured (established 1024 bind 1024)
[    1.075167] UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.088017] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
[    1.102095] NET: Registered protocol family 1
[    1.110644] PCI: CLS 0 bytes, default 32
[    6.981662] workingset: timestamp_bits=14 max_order=14 bucket_order=0
[    7.000121] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    7.011582] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    7.033199] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    7.050449] mt7621_gpio 10000600.gpio: registering 32 gpios
[    7.061738] mt7621_gpio 10000600.gpio: registering 32 gpios
[    7.072952] mt7621_gpio 10000600.gpio: registering 32 gpios
[    7.084217] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    7.099643] printk: console [ttyS0] disabled
[    7.108121] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A
[    7.125935] printk: console [ttyS0] enabled
[    7.125935] printk: console [ttyS0] enabled
[    7.142422] printk: bootconsole [early0] disabled
[    7.142422] printk: bootconsole [early0] disabled
[    7.162642] spi-mt7621 10000b00.spi: sys_freq: 193333333
[    7.193548] spi-nor spi0.0: en25qh64 (8192 Kbytes)
[    7.203179] 4 fixed-partitions partitions found on MTD device spi0.0
[    7.215841] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    7.230357] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    7.245395] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    7.259945] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions
[    7.274695] Creating 4 MTD partitions on "spi0.0":
[    7.284243] 0x000000000000-0x000000030000 : "u-boot"
[    7.297837] 0x000000030000-0x000000040000 : "u-boot-env"
[    7.309719] 0x000000040000-0x000000050000 : "factory"
[    7.323074] 0x000000050000-0x000000800000 : "firmware"
[    7.389673] rt3050-esw 10110000.esw: mediatek esw at 0xb0110000, irq 25 initialized
[    7.405777] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[    7.424194] NET: Registered protocol family 10
[    7.439040] Segment Routing with IPv6
[    7.446514] NET: Registered protocol family 17
[    7.455453] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    7.481139] 8021q: 802.1Q VLAN Support v1.8
[    7.514577] Freeing unused kernel memory: 4188K
[    7.523595] This architecture does not have kernel memory protection.
[    7.536368] Run /init as init process
[    8.058531] init: Console is alive
[    8.065990] init: - watchdog -
[    8.101861] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    8.124086] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    8.149122] init: - preinit -
[    8.468087] random: jshn: uninitialized urandom read (4 bytes read)
[    8.594616] random: jshn: uninitialized urandom read (4 bytes read)
[    8.873252] random: jshn: uninitialized urandom read (4 bytes read)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[   11.539588] procd: - early -
[   11.545854] procd: - watchdog -
[   12.190327] procd: - watchdog -
[   12.197082] procd: - ubus -
[   12.213705] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.254375] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.267785] random: ubusd: uninitialized urandom read (4 bytes read)
[   12.285351] procd: - init -
Please press Enter to activate this console.
[   13.138034] kmodloader: loading kernel modules from /etc/modules.d/*
[   13.746067] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[   13.761144] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[   13.787369] urngd: v1.0.2 started.
[   13.976930] mt76_wmac 10300000.wmac: ASIC revision: 76280001
[   14.168839] random: crng init done
[   14.175651] random: 26 urandom warning(s) missed due to ratelimiting
[   14.740421] rt3050-esw 10110000.esw: port 0 link up
[   15.023423] mt76_wmac 10300000.wmac: Firmware Version: 20151201
[   15.035212] mt76_wmac 10300000.wmac: Build Time: 20151201183641
[   15.061514] mt76_wmac 10300000.wmac: firmware init done
[   15.375313] PPP generic driver version 2.4.2
[   15.402847] NET: Registered protocol family 24
[   15.448598] kmodloader: done loading kernel modules from /etc/modules.d/*
[   52.649591] rt3050-esw 10110000.esw: port 0 link down
[   56.826427] rt3050-esw 10110000.esw: port 0 link up
[   58.569787] br-lan: port 1(eth0.1) entered blocking state
[   58.580584] br-lan: port 1(eth0.1) entered disabled state
[   58.591902] device eth0.1 entered promiscuous mode
[   58.601400] device eth0 entered promiscuous mode
[   58.680925] br-lan: port 1(eth0.1) entered blocking state
[   58.691700] br-lan: port 1(eth0.1) entered forwarding state
[   59.592319] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



BusyBox v1.35.0 (2022-08-09 11:57:39 UTC) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 OpenWrt SNAPSHOT, r20266-cf110404e3
 -----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/#

But it does not show the 5Ghz radio...

Does anyone have some time to show me how to get it working?

1 Like
3

5Ghz chip is MT7613AEN

20220824_110612
20220824_1106121920×1440 217 KB

4
5

In the dts files of similar devices there is just

&pcie0 {
	mt76@0,0 {
		reg = <0x0000 0 0 0 0>;
		mediatek,mtd-eeprom = <&factory 0x8000>;
		ieee80211-freq-limit = <5000000 6000000>;
	};
};

I would like to understand what else I could check.

6

I took the Wavlink WL-WN570HA1 file as template.
partition layout fits

reset gpio 38
lan led gpio 43
wlan led gpio 44 (my unit has a wire soldered between 2.4 and 5Ghz LED, both LEDs are connected at gpio44)

added the following packages to start the 5Ghz radio:
kmod-mt7615-firmware kmod-mt7615e kmod-mt7663-firmware-ap

5Ghz is now working!

7

The original bootlog seems to indicate, that the 5Ghz NIC is connected via PCI.
Do you see the device visible in the list of PCI devices in your Openwrt FW?

Did you verify with lsmod, that the kernel module is actually loading?

8

5Ghz is working with the packages from my last post!

i am about to test it in my mesh right now.

9

DFS is unsupported on the MT7613 radio with OpenWrt!