Add support for D-Link COVR-X1860

For Developers
181

Blink red ?

182

only red, no blinking

183

openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin is not intended to be used with sysupgrade, openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-sysupgrade.bin would be the correct one in this case.
Not sure what is happening when you sysupgrade with the wrong image, but my expectation is that recovery mode is still possible afterwards because the boot loader is not modified.

184

Also no red blinking when you try to enter recovery mode?

185

what are the settings to connect over ttl?

186

U need click reset and put power on and wait for blink.

187

ok, now is blinking red and the network card show a link is up
but no website is possible to open

188

U need manual write lan IP like 192.168.0.2 mask 255.255.255.0

189

ok, found the problem the recory page is on 192.168.0.1 now I can upload a file, with one is the right for this?

190

openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin

1 Like
191

ok was successfull but openwrt only over ssh is possible. Red LED is fast flashing

192

Did you reset the IP configuration to DHCP?

193

No set a static ip 192.168.1.10, dhcp is not working. Ping to 192.168.1.1 is possible and also ssh.

BusyBox v1.36.1 (2023-05-24 21:53:33 UTC) built-in shell (ash)

| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -| || | | || || |
|_____|| |||||___||| |____|
|| W I R E L E S S F R E E D O M

OpenWrt SNAPSHOT, r23086+1-3591353f51

================= FAILSAFE MODE active ================
special commands:

  • firstboot reset settings to factory defaults
  • mount_root mount root-partition with config files

after mount_root:

  • passwd change root's password
  • /etc/config directory with config files

for more help see:

  • failsafe_and_factory_reset
  • root_password_reset
    =======================================================

root@(none):~# firstboot
This will erase all settings and remove any installed packages. Are you sure? [N/y]
y
/dev/ubi0_1 is not mounted
/dev/ubi0_1 will be erased on next mount

194

That looks strange. Where did you get the image from?

195

not 100% sure but from here Release COVR-X1860_Build_20230724 · RolandoMagico/openwrt-build (github.com)
so will try again with this one?
https://github.com/RolandoMagico/openwrt-build/releases/download/COVR-X1860_Build_20230806/openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin

196

I didn't find your version r23086+1-3591353f51 in my builds. But yes, you can try https://github.com/RolandoMagico/openwrt-build/releases/download/COVR-X1860_Build_20230806/openwrt-ramips-mt7621-dlink_covr-x1860-a1-squashfs-recovery.bin

197

Do I need to manually reset the device after recovery, or will it reboot on its own?

198

And use a chrome based browser, other browsers might not do the upload correctly

199

The device should boot automatically if the flash process was successful. If flashing didn't work, it usually will stay in recovery mode and continue blinking red.

200

I used EDGE Browser.
Upgrade was successfull but no reboot.

And now openwrt is like this:

BusyBox v1.36.1 (2023-08-01 19:15:03 UTC) built-in shell (ash)

| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -| || | | || || |
|_____|| |||||___||| |____|
|| W I R E L E S S F R E E D O M

OpenWrt SNAPSHOT, r23693-b5eddcd524