Here is console boot of dd-wrt build from today.
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Thu Jan 3 14:20:25 CST 2008 (root@linux)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI: Initializing host
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Boot partition size = 262144(0x40000)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 003F7FFF (3899364)
nvram #03 003F8000 -> 003FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 003F7FFF (3899392)
nvram #02 003F8000 -> 003FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80700000 - 0x807A2600 (665088)
Initialized Data: 0x80737980 - 0x8073A880 (12032)
BSS Area: 0x8073A880 - 0x8073C600 (7552)
Local Heap: 0x8073C600 - 0x807A0600 (409600)
Stack Area: 0x807A0600 - 0x807A2600 (8192)
Text (code) segment: 0x80700000 - 0x80737980 (227712)
Boot area (physical): 0x007A3000 - 0x007E3000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.7
The boot is CFE
mac_init(): Find mac [00:22:6b:58:10:0d] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 1000BaseT FDX
Device eth0: hwaddr 00-22-6B-58-10-0D, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x3A0000 (3801088) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x9A8 (2472) (0xBC0409A8)
Offset2: 0xE2C00 (928768) (0xBC122C00)
Header CRC: 0x645859E
Calculate CRC: 0x645859E
Image 1 is OK
Try to load image 1.
Waiting for 5 seconds to upgrade ...
CMD: [load -raw -addr=0x807a2600 -max=0x770000 :]
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: _tftpd_open(): retries=0/5
_tftpd_open(): retries=1/5
_tftpd_open(): retries=2/5
_tftpd_open(): retries=3/5
_tftpd_open(): retries=4/5
Failed.
Could not load :: Timeout occured
CMD: [boot -raw -z -addr=0x80001000 -max=0x770000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3856 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
CPU revision is: 0002901a
Linux version 2.4.37 (root@dd-wrt) (gcc version 3.4.6 (OpenWrt-2.0)) #3367 Sat Feb 7 01:30:41 CET 2009
Setting the PFC to its default value
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
CPU: BCM4785 rev 2 at 300 MHz
Using 150.000 MHz high precision timer.
Calibrating delay loop... 299.82 BogoMIPS
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Ignoring BAR0-1 of IDE controller 00:06.0
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 2) is a 16550A
ttyS01 at 0xb8000400 (irq = 2) is a 16550A
PCI: Setting latency timer of device 01:01.0 to 64
PCI: Enabling device 01:01.0 (0004 -> 0006)
Overriding boardvendor: 0x14e4 instead of 0x14e4
Overriding boardtype: 0x46d instead of 0x4321
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Physically mapped flash: Found an alias at 0x400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0xc00000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1400000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1c00000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x400000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x2bcabb
partition size = 2872320
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x003f0000 : "linux"
0x00122c00-0x003e0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
0x003e0000-0x003f0000 : "ddwrt"
sflash not supported on this router
Initializing Cryptographic API
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (512 buckets, 4096 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
netfilter PSD loaded - (c) astaro AG
ipt_osf: Startng OS fingerprint matching module.
ipt_IPV4OPTSSTRIP loaded
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
starting Architecture code for broadcom
Booting device: Linksys WRT310N
loading bcm57xxlsys
bcm_robo_attach: Resetting 539x robo switch
dd-wrt already booted, use internal fixup
configure vlan1 (1 2 3 4 8*) instead of vlan0 for BCM5395
sh: can't create /proc/switch/eth0/reset: nonexistent directory
sh: can't create /proc/switch/eth1/reset: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/2/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/2/ports: nonexistent directory
sh: can't create /proc/sys/net/ipv4/tcp_congestion_control: nonexistent directory
eth0: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
channel 6, val 20
800, 300, 6
spec 2B06
eth0: Numerical result out of range
eth0: Invalid argument
eth0: Invalid argument
eth0: Operation not supported
eth0: Operation not supported
br0: Bad file descriptor
br0: Bad file descriptor
eth0: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
channel 6, val 20
800, 300, 6
spec 2B06
eth0: Numerical result out of range
eth0: Invalid argument
eth0: Invalid argument
eth0: Operation not supported
eth0: Operation not supported
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
vlan2: Setting MAC address to 00 22 6b 58 10 0e.
sh: /tmp/.rc_startup: not found
DD-WRT v24 std (c) 2008 NewMedia-NET GmbH
Release: 02/07/09 (SVN revision: 11571)
�
DD-WRT login: root
Password:
==========================================================
____ ___ __ ______ _____ ____ _ _
| _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
|| | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
|___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|
DD-WRT v24-sp2
http://www.dd-wrt.com
==========================================================
Jan 1 00:00:22 login[410]: root login on 'console'
BusyBox v1.13.2 (2009-02-07 01:27:49 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# cat /proc/mtd
dev: size erasesize name
mtd0: 00040000 00010000 "cfe"
mtd1: 003b0000 00010000 "linux"
mtd2: 002bd400 00010000 "rootfs"
mtd3: 00010000 00010000 "nvram"
mtd4: 00010000 00010000 "ddwrt"
root@DD-WRT:~# uname -a
Linux DD-WRT 2.4.37 #3367 Sat Feb 7 01:30:41 CET 2009 mips unknown
root@DD-WRT:~#
(Last edited by RoundSparrow on 7 Feb 2009, 22:40)