OpenWrt Forum Archive

Hi everybody!
I compiled Kamikaze and flashed to my WAG54G successfully
Now I'm trying to get my DSL connection up...

Original Linksys firmware settings:
ATM PVC SETTINGS
PVC: PVC0
VPI: 8
VCI: 35
Virtual circuit: enabled
Username: user
Password: passwd
Connection type: PPPoE LLC
MTU: 1400
MRU: 1492
Default route: enabled
IP control: dynamic IP

OpenWRT settings:

# br2684ctl -b -c 0 -e 0 -a 8.35
RFC1483/2684 bridge: Interface "nas0" (mtu=1500, payload=bridged) created sucessfully 
RFC1483/2684 bridge: Communicating over ATM 0.8.35, encapsulation: LLC 
RFC1483/2684 bridge: Interface configured
RFC1483/2684 bridge: RFC 1483/2684 bridge daemon started 
# cat /proc/tiatm/avsar_modem_training 
SHOWTIME
# ls -l /dev/ppp 
crw-------    1 root     root     108,   0 Jan  1  1970 /dev/ppp

# cat /etc/config/network
config interface loopback
        option ifname   lo
        option proto    static
        option ipaddr   127.0.0.1
        option netmask  255.0.0.0

config interface lan
        option ifname   eth0
        option proto    static
        option ipaddr   192.168.1.1
        option netmask  255.255.255.0

config interface wan
        option ifname   nas0
        option device   ppp
        option proto    pppoe
        option username user
        option password passwd

# cat /etc/ppp/options
debug
lock
defaultroute
noipdefault
noauth
passive
asyncmap 0
usepeerdns
user "user"
name "user"
lcp-echo-interval 4
lcp-echo-failure 20
mtu 1400
mru 1492

# cat /etc/ppp/chap-secrets (same for pap-secrets)
user * passwd *

# ifup wan
Plugin rp-pppoe.so loaded.
# logread
daemon.warn pppd[2367]: Timeout waiting for PADO packets
daemon.err pppd[2367]: Unable to complete PPPoE Discovery
daemon.warn pppd[2367]: Timeout waiting for PADO packets
daemon.err pppd[2367]: Unable to complete PPPoE Discovery
daemon.warn pppd[2367]: Timeout waiting for PADO packets
daemon.err pppd[2367]: Unable to complete PPPoE Discovery
# ps
...
  850 root        608 S   /usr/sbin/dropbear -p 22 
  852 root        560 S   -ash 
 2215 root        300 S   br2684ctl -b -c 0 -e 0 -a 8.35 
 2431 root        568 S   /usr/sbin/pppd plugin rp-pppoe.so mtu 1480 mru 1480 n
 2433 root        376 R   ps

# ifconfig 
eth0      Link encap:Ethernet  HWaddr 00:13:10:3F:CA:40  
          inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:159 errors:0 dropped:0 overruns:0 frame:0
          TX packets:100 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:16595 (16.2 KiB)  TX bytes:12079 (11.7 KiB)
          Base address:0x2800 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

nas0      Link encap:Ethernet  HWaddr 00:00:02:03:04:05  
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:42 (42.0 B)

I tried also little variations, such as placing username and password between "..." or set paylod to routed instead of bridged...

Any hint?

Thank you!

(Last edited by heruan on 28 Jan 2007, 14:55)