Thank you. I have bs-u25awf hdd enclosure. I try your firmware. And i need help mount hdd.
UPDATE: I installed ur firmware. It works great but still cant mount hdd. help me,
update:
here is my dmesg:
root@OpenWrt:~# dmesg
[ 0.000000] Linux version 4.9.82 (courtois@debian) (gcc version 5.5.0 (OpenWr t GCC 5.5.0 r6320-fc54256bc8) ) #0 Mon Feb 26 16:52:15 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Kimax U25AWF-H1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 803f8ef4, node_mem_map 8100002 0
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 32512
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=0006c7ba
[ 0.000000] Readback ErrCtl register=0006c7ba
[ 0.000000] Memory: 125340K/131072K available (3160K kernel code, 156K rwdata , 756K rodata, 208K init, 217K bss, 5732K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015457] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080609] pid_max: default: 32768 minimum: 301
[ 0.089916] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102945] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.123545] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.143030] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.155177] pinctrl core: initialized pinctrl subsystem
[ 0.166148] NET: Registered protocol family 16
[ 0.196946] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.207975] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.220554] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.231552] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.244103] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.254917] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.270839] clocksource: Switched to clocksource systick
[ 0.282585] NET: Registered protocol family 2
[ 0.292078] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.305853] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.318449] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.331174] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.342703] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.355390] NET: Registered protocol family 1
[ 0.363967] PCI: CLS 0 bytes, default 32
[ 0.366311] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.379009] Crashlog allocated RAM at address 0x3f00000
[ 0.390487] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[ 0.411521] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.423003] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.451405] io scheduler noop registered
[ 0.459048] io scheduler deadline registered (default)
[ 0.469613] ralink-usb-phy usbphy: invalid resource
[ 0.479767] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.493412] console [ttyS0] disabled
[ 0.500404] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.520177] console [ttyS0] enabled
[ 0.533953] bootconsole [early0] disabled
[ 0.554278] spi spi0.0: force spi mode3
[ 0.562795] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.572958] 4 ofpart partitions found on MTD device spi0.0
[ 0.583891] Creating 4 MTD partitions on "spi0.0":
[ 0.593452] 0x000000000000-0x000000030000 : "u-boot"
[ 0.605053] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.617588] 0x000000040000-0x000000050000 : "factory"
[ 0.629592] 0x000000050000-0x000001000000 : "firmware"
[ 0.727750] 2 uimage-fw partitions found on MTD device firmware
[ 0.739592] 0x000000050000-0x00000019bda8 : "kernel"
[ 0.751242] 0x00000019bda8-0x000001000000 : "rootfs"
[ 0.763001] mtd: device 5 (rootfs) set to be root filesystem
[ 0.774930] 1 squashfs-split partitions found on MTD device rootfs
[ 0.787316] 0x0000007c0000-0x000001000000 : "rootfs_data"
[ 0.800323] libphy: Fixed MDIO Bus: probed
[ 0.812200] gsw: setting port4 to ephy mode
[ 0.820577] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 4 link u p (100Mbps/Full duplex)
[ 0.839026] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.851696] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 0.868728] rt2880_wdt 10000120.watchdog: Initialized
[ 0.879958] NET: Registered protocol family 10
[ 0.891994] NET: Registered protocol family 17
[ 0.900977] 8021q: 802.1Q VLAN Support v1.8
[ 0.921780] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.936988] Freeing unused kernel memory: 208K
[ 0.945871] This architecture does not have kernel memory protection.
[ 2.403893] init: Console is alive
[ 2.410977] init: - watchdog -
[ 2.530802] random: fast init done
[ 6.450295] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.794269] usbcore: registered new interface driver usbfs
[ 6.805399] usbcore: registered new interface driver hub
[ 6.816123] usbcore: registered new device driver usb
[ 6.858983] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.881381] SCSI subsystem initialized
[ 6.894352] ehci-platform: EHCI generic platform driver
[ 6.915157] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.926967] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.935860] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.947352] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.963264] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.984479] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.998078] hub 1-0:1.0: USB hub found
[ 7.005952] hub 1-0:1.0: 1 port detected
[ 7.015860] ehci-pci: EHCI PCI platform driver
[ 7.028085] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 7.042071] ohci-platform: OHCI generic platform driver
[ 7.052838] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 7.066427] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 7.082341] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 7.123447] hub 2-0:1.0: USB hub found
[ 7.131354] hub 2-0:1.0: 1 port detected
[ 7.142091] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.172557] usbcore: registered new interface driver usb-storage
[ 7.185318] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 7.203885] init: - preinit -
[ 9.794757] 8021q: adding VLAN 0 to HW filter on device eth0
[ 11.196742] mount_root: loading kmods from internal overlay
[ 11.276234] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.292017] kmodloader: done loading kernel modules from //etc/modules-boot.d /*
[ 13.749852] jffs2: notice: (373) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 13.781568] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 13.811667] block: extroot: not configured
[ 14.073788] jffs2: notice: (370) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 15.688203] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 15.717478] block: extroot: not configured
[ 15.727121] mount_root: switching to jffs2 overlay
[ 15.808983] urandom-seed: Seeding with /etc/urandom.seed
[ 15.923618] procd: - early -
[ 15.929452] procd: - watchdog -
[ 16.651965] procd: - watchdog -
[ 16.663220] procd: - ubus -
[ 16.854599] procd: - init -
[ 17.478866] kmodloader: loading kernel modules from /etc/modules.d/*
[ 17.558894] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 17.598557] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.668136] Netfilter messages via NETLINK v0.30.
[ 17.681539] ip_set: protocol 6
[ 17.736135] fuse init (API version 7.26)
[ 17.753309] usbcore: registered new interface driver cdc_wdm
[ 17.767129] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 17.783160] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 17.803325] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.830109] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 17.845882] nf_conntrack_rtsp v0.7 loading
[ 17.935167] nf_nat_rtsp v0.7 loading
[ 17.953106] usbcore: registered new interface driver ums-alauda
[ 17.967744] usbcore: registered new interface driver ums-cypress
[ 17.982653] usbcore: registered new interface driver ums-datafab
[ 17.997319] usbcore: registered new interface driver ums-freecom
[ 18.012164] usbcore: registered new interface driver ums-isd200
[ 18.027006] usbcore: registered new interface driver ums-jumpshot
[ 18.041878] usbcore: registered new interface driver ums-karma
[ 18.057104] usbcore: registered new interface driver ums-sddr09
[ 18.071808] usbcore: registered new interface driver ums-sddr55
[ 18.086852] usbcore: registered new interface driver ums-usbat
[ 18.101904] usbcore: registered new interface driver usblp
[ 18.127775] usbcore: registered new interface driver usbserial
[ 18.139559] usbcore: registered new interface driver usbserial_generic
[ 18.152719] usbserial: USB Serial support registered for generic
[ 18.216311] xt_time: kernel timezone is -0000
[ 18.229984] usbcore: registered new interface driver cdc_ether
[ 18.443541] PPP generic driver version 2.4.2
[ 18.455354] NET: Registered protocol family 24
[ 18.467894] usbcore: registered new interface driver qmi_wwan
[ 18.483777] usbcore: registered new interface driver rndis_host
[ 18.516225] usbcore: registered new interface driver sierra_net
[ 18.536076] usbcore: registered new interface driver option
[ 18.547380] usbserial: USB Serial support registered for GSM modem (1-port)
[ 18.590969] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory "
[ 18.605466] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 d etected
[ 18.620924] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 18.635342] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.720802] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 27.875620] 8021q: adding VLAN 0 to HW filter on device eth0
[ 27.918299] br-lan: port 1(eth0) entered blocking state
[ 27.928809] br-lan: port 1(eth0) entered disabled state
[ 27.939693] device eth0 entered promiscuous mode
[ 28.034235] br-lan: port 1(eth0) entered blocking state
[ 28.044717] br-lan: port 1(eth0) entered forwarding state
[ 28.055897] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 30.636716] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 35.711680] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 35.754666] br-lan: port 2(wlan0-1) entered blocking state
[ 35.765692] br-lan: port 2(wlan0-1) entered disabled state
[ 35.777087] device wlan0-1 entered promiscuous mode
[ 36.312597] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 39.897565] wlan0: authenticate with ec:08:6b:4a:b9:ba
[ 39.975784] wlan0: send auth to ec:08:6b:4a:b9:ba (try 1/3)
[ 39.989545] wlan0: authenticated
[ 40.022902] wlan0: associate with ec:08:6b:4a:b9:ba (try 1/3)
[ 40.059320] wlan0: RX AssocResp from ec:08:6b:4a:b9:ba (capab=0x431 status=0 aid=7)
[ 40.074940] wlan0: associated
[ 41.051254] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 42.463189] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 42.476460] br-lan: port 2(wlan0-1) entered blocking state
[ 42.487432] br-lan: port 2(wlan0-1) entered forwarding state
[ 59.880857] random: crng init done
[ 312.137141] br-lan: port 2(wlan0-1) entered disabled state
[ 315.441810] wlan0: authenticate with ec:08:6b:4a:b9:ba
[ 315.461647] wlan0: send auth to ec:08:6b:4a:b9:ba (try 1/3)
[ 315.473991] wlan0: authenticated
[ 315.484323] wlan0: associate with ec:08:6b:4a:b9:ba (try 1/3)
[ 315.497256] wlan0: RX AssocResp from ec:08:6b:4a:b9:ba (capab=0x431 status=0 aid=7)
[ 315.512847] wlan0: associated
[ 315.534360] br-lan: port 2(wlan0-1) entered blocking state
[ 315.545358] br-lan: port 2(wlan0-1) entered forwarding state
(Last edited by ganzo8247 on 3 Mar 2018, 08:48)