Hello all,
Forgive me if this has been mentioned before, I couldn't see anything on the search.
Decided to upgrade home hub v5a to openwrt as a project. got everything working until it came to activating wifi radios. nothing. No file created, iw list empty. I've attached the "dmesg | grep pci" output, looks like it can't find the firmware? How would I correct this?
Any help appreciated
edit: using lede 17.01.4.
[ 0.232783] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.366774] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
[ 0.406467] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.413374] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff]
[ 0.420318] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.427174] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.435224] pci 0000:00:0e.0: [168c:ff1d] type 00 class 0x020000
[ 0.435283] pci 0000:00:0e.0: reg 0x10: [mem 0x00000000-0x0000ffff]
[ 0.435646] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.435687] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.446539] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[ 0.453454] pci_bus 0000:01: root bus resource [io 0x1d800000-0x1d8fffff]
[ 0.460395] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[ 0.467250] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.475279] pci 0000:01:00.0: [1bef:0011] type 01 class 0x060000
[ 0.475314] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[ 0.493061] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.493368] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
[ 0.501497] pci 0000:02:00.0: [168c:003c] type 00 class 0x028000
[ 0.501585] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 0.501655] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 0.501759] pci 0000:02:00.0: supports D1 D2
[ 0.502040] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 0.502078] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 02
[ 0.502131] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
[ 0.508808] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref]
[ 0.516075] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bit]
[ 0.523473] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref]
[ 0.530736] pci 0000:01:00.0: PCI bridge to [bus 02]
[ 0.535774] pci 0000:01:00.0: bridge window [mem 0x1c000000-0x1c1fffff]
[ 0.542630] pci 0000:01:00.0: bridge window [mem 0x1c200000-0x1c2fffff pref]
[ 0.549999] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[ 0.556605] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[ 0.562948] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
[ 0.569614] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
[ 10.669373] ath10k_pci 0000:02:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
[ 10.866383] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 10.875702] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 10.995305] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 11.003229] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[ 11.013238] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.293170] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 11.543753] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 11.551622] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 11.566981] ath10k_pci 0000:02:00.0: firmware ver 10.2.4-1.0-00016 api 5 features no-p2p,raw-mode,mfp crc32 0c5668f8
[ 11.616196] ath10k_pci 0000:02:00.0: board id is not exist in otp, ignore it
[ 11.621982] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 11.632289] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 11.758576] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 11.884911] ath10k_pci 0000:02:00.0: otp calibration failed: 2
[ 11.889342] ath10k_pci 0000:02:00.0: failed to run otp: -22
[ 11.894897] ath10k_pci 0000:02:00.0: could not init core (-22)
[ 11.900861] ath10k_pci 0000:02:00.0: could not probe fw (-22)
[ 12.057240] owl-loader 0000:00:0e.0: Direct firmware load for ath9k-eeprom-pci-0000:00:0e.0.bin failed with error -2
[ 12.344743] firmware ath9k-eeprom-pci-0000:00:0e.0.bin: firmware_loading_store: map pages failed
(Last edited by Vaudane on 17 Mar 2018, 21:48)