U-Boot 1.1.3 (Apr 10 2013 - 15:50:37)
Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb4000
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: 1 20 18 4d 1 (20184d01)
find flash: S25FL129P
raspi_read: from:30000 len:1000
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 10 2013 Time:15:50:37
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
##### The CPU freq = 580 MHZ ####
estimate memory size =64 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP.
You choosed 3
0
3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: MIPS OpenWrt Linux-3.18.23
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1179078 Bytes = 1.1 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:50040 len:11fdc6
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 64
Starting kernel ...
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 14:11:59 CET 2016
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Kingston MLW221
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007fffe
[ 0.000000] Readback ErrCtl register=0007fffe
[ 0.000000] Memory: 61240K/65536K available (2622K kernel code, 129K rwdata, 528K rodata, 168K init, 190K bss, 4296K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.010000] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] pinctrl core: initialized pinctrl subsystem
[ 0.100000] NET: Registered protocol family 16
[ 0.120000] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.130000] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.140000] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.150000] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.160000] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.170000] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.180000] Switched to clocksource systick
[ 0.190000] NET: Registered protocol family 2
[ 0.190000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.210000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.230000] TCP: reno registered
[ 0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.260000] NET: Registered protocol family 1
[ 0.270000] rt-timer 10000100.timer: maximum frequency is 2441Hz
[ 0.290000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.310000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.340000] msgmni has been set to 119
[ 0.350000] io scheduler noop registered
[ 0.350000] io scheduler deadline registered (default)
[ 0.370000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.380000] console [ttyS0] disabled
[ 0.390000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[ 0.410000] console [ttyS0] enabled
[ 0.410000] console [ttyS0] enabled
[ 0.420000] bootconsole [early0] disabled
[ 0.420000] bootconsole [early0] disabled
[ 0.450000] m25p80 spi32766.0: s25fl129p1 (16384 Kbytes)
[ 0.460000] 5 ofpart partitions found on MTD device spi32766.0
[ 0.470000] Creating 5 MTD partitions on "spi32766.0":
[ 0.480000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.500000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.510000] 0x000000040000-0x000000050000 : "factory"
[ 0.520000] 0x000000050000-0x000000fb0000 : "firmware"
[ 0.650000] 2 uimage-fw partitions found on MTD device firmware
[ 0.660000] 0x000000050000-0x00000016fe06 : "kernel"
[ 0.670000] 0x00000016fe06-0x000000fb0000 : "rootfs"
[ 0.680000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.690000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.700000] 0x000000930000-0x000000fb0000 : "rootfs_data"
[ 0.720000] 0x000000fb0000-0x000001000000 : "user-config"
[ 0.730000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
[ 0.750000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.760000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.780000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.790000] TCP: cubic registered
[ 0.790000] NET: Registered protocol family 17
[ 0.800000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.830000] Bridge firewalling registered
[ 0.840000] 8021q: 802.1Q VLAN Support v1.8
[ 0.870000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.880000] Freeing unused kernel memory: 168K (80336000 - 80360000)
[ 3.580000] init: Console is alive
[ 3.590000] init: - watchdog -
[ 9.080000] usbcore: registered new interface driver usbfs
[ 9.100000] usbcore: registered new interface driver hub
[ 9.110000] usbcore: registered new device driver usb
[ 9.150000] SCSI subsystem initialized
[ 9.170000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.180000] ehci-platform: EHCI generic platform driver
[ 9.390000] phy phy-usbphy.0: remote usb device wakeup disabled
[ 9.410000] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 9.420000] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 9.430000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 9.440000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 9.470000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 9.480000] hub 1-0:1.0: USB hub found
[ 9.490000] hub 1-0:1.0: 1 port detected
[ 9.500000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.510000] ohci-platform: OHCI generic platform driver
[ 9.520000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 9.540000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 9.550000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 9.620000] hub 2-0:1.0: USB hub found
[ 9.630000] hub 2-0:1.0: 1 port detected
[ 9.650000] MTK MSDC device init.
[ 9.650000] mtk-sd: MediaTek MT6575 MSDC Driver
[ 9.670000] sdhci: Secure Digital Host Controller Interface driver
[ 9.680000] sdhci: Copyright(c) Pierre Ossman
[ 9.690000] sdhci-pltfm: SDHCI platform and OF driver helper
[ 9.710000] usbcore: registered new interface driver usb-storage
[ 9.810000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 9.970000] hub 1-1:1.0: USB hub found
[ 9.980000] hub 1-1:1.0: 3 ports detected
[ 10.620000] init: - preinit -
[ 12.420000] 8021q: adding VLAN 0 to HW filter on device eth0
[ 12.460000] random: procd urandom read with 20 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 15.700000] mount_root: loading kmods from internal overlay
[ 19.920000] jffs2: notice: (363) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 19.950000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 20.010000] block: extroot: not configured
[ 21.080000] jffs2: notice: (359) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 23.810000] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[ 23.850000] block: extroot: not configured
[ 23.860000] mount_root: switching to jffs2 overlay
[ 23.900000] procd: - early -
[ 23.910000] procd: - watchdog -
[ 25.010000] procd: - ubus -
[ 26.030000] procd: - init -
Please press Enter to activate this console.
[ 27.750000] NET: Registered protocol family 10
[ 27.780000] ntfs: driver 2.1.31 [Flags: R/O MODULE].
[ 27.810000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 27.850000] hidraw: raw HID events driver (C) Jiri Kosina
[ 27.870000] fuse init (API version 7.23)
[ 28.030000] Bluetooth: Core ver 2.19
[ 28.030000] NET: Registered protocol family 31
[ 28.040000] Bluetooth: HCI device and connection manager initialized
[ 28.060000] Bluetooth: HCI socket layer initialized
[ 28.070000] Bluetooth: L2CAP socket layer initialized
[ 28.080000] Bluetooth: SCO socket layer initialized
[ 28.090000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 28.100000] Bluetooth: BNEP filters: protocol multicast
[ 28.110000] Bluetooth: BNEP socket layer initialized
[ 28.120000] usbcore: registered new interface driver btusb
[ 28.140000] usbcore: registered new interface driver cdc_acm
[ 28.150000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 28.170000] usbcore: registered new interface driver cdc_wdm
[ 28.180000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 28.200000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 28.220000] Bluetooth: HCI UART driver ver 2.2
[ 28.230000] Bluetooth: HCI H4 protocol initialized
[ 28.240000] Bluetooth: HCI BCSP protocol initialized
[ 28.250000] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 28.260000] Bluetooth: HIDP socket layer initialized
[ 28.27000