Please help. I'm desperate. 
I bricked my WRT1900AC on a bad DD-WRT load and yes I'm here for some help. I can easily recover back to Linksys firmware using a Serial Cable and the commands:
setenv firmware_name xxxx.IMG
setenv ipaddr 192.168.1.1
setenv netmask 255.255.255.0
setenv serverip 192.168.1.2
run update_both_images
Once in the Linksys firmware, NOTHING I do allows me to load DD-WRT Again. And yes, I'm using the proper factory-to-ddwrt.img files from the Linksys 1.1.8. 161917 firmware. After the flash it just goes into a boot loop and seems to not be able to find "directories" during the boot process. Below is a capture I'm hoping someone can eyeball and help. I would be extremely grateful.
//Brew
firmware does not have Linksys signature
altering uboot parameters for OpenWRT firmware
CAUTION: turning OFF auto_recovery in uboot
Firmware upgrade in process...
Erasing... /dev/mtd6
Programming... /dev/mtd6
committing syscfg
system is going down
wifi, sysevent received: wifi-stop (Wed Oct 10 23:01:43 PDT 2012)
wifi, service_stop()
wifi, wifi_virtual_stop(wdev0)
wifi, wifi_guest_stop(wdev0)
wifi, wifi_guest_wdev0 is already stopping/stopped, ignore this request
wifi, wifi_user_stop(wdev0)
l2_packet_receive - recvfrom: Network is down
wifi, primary AP: wdev0ap0 is down
wifi, stop process: 7477 root 2008 S hostapd-mon -v -0 /tmp/hostapd-wdev0ap0.conf on wdev0ap0
wifi, wifi_physical_stop(wdev0)
wifi_physical, ifconfig wdev0 down
wifi, wifi_virtual_stop(wdev1)
ELOOP: remaining socket: sock=13 eloop_data=0x75668 user_data=(nil) handler=0x33e14
ELOOP: remaining socket: sock=14 eloop_data=0x756b8 user_data=(nil) handler=0x33e14
ELOOP: remaining socket: sock=15 eloop_data=0x75718 user_data=(nil) handler=0x334ec
ELOOP: remaining socket: sock=21 eloop_data=0x77b38 user_data=(nil) handler=0x33e14
ELOOP: remaining socket: sock=22 eloop_data=0x775c0 user_data=(nil) handler=0x33e14
ELOOP: remaining socket: sock=23 eloop_data=0x77c08 user_data=(nil) handler=0x334ec
wifi, wifi_guest_stop(wdev1)
wifi, wifi_guest_wdev1 is already stopping/stopped, ignore this request
wifi, wifi_user_stop(wdev1)
wifi, primary AP: wdev1ap0 is down
wifi, stop process: 7490 root 2008 S hostapd-mon -v -1 /tmp/hostapd-wdev1ap0.conf on wdev1ap0
wifi, wifi_physical_stop(wdev1)
wifi_physical, ifconfig wdev1 down
Guest access control is down
/etc/init.d/service_system.sh: line 97: can't create /dev/console: Read-only file system
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
Restarting system.
BootROM 1.20
Booting from NAND flash
Step 1: First phase of PEX-PIPE Configuration
Step 2: Configure the desire PIN_PHY_GEN
Step 3 QSGMII enable
Step 4: Configure SERDES MUXes
Step 5: Activate the RX High Impedance Mode
Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)
Step 6.2: [PEX-Only] PCI Express Link Capabilities
Step 7: [PEX-X4 Only] To create PEX-Link
Steps 7,8,9,10 and 11
Steps 12: [PEX-Only] Last phase of PEX-PIPE ConfigurationSteps 13: Wait 15ms before checking resultsSteps 14: [PEX-Only] In order to configureSteps 15: [PEX-Only] In order to configureSteps 16: [PEX-Only] Training Enablestep 17: max_if= 0x7
step 17: PEX0 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0050
mvPexConfigRead: return addr=0x%x0050
--> 7001
--> 7001
--> A005
--> A005
--> 0010
--> 4C12
Gen2 client!
step 17: PEX1 pexUnit= 0
step 17: PEX2 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0040
mvPexConfigRead: return addr=0x%x0040
--> 5001
--> 5001
--> 7005
--> 7005
--> 0010
--> DC12
Gen2 client!
step 17: PEX3 pexUnit= 0
PEX3 : Detected No Link. Status Reg(0x0004DA64) = 0x00000001
step 17: PEX4 pexUnit= 1
PEX4 : Detected No Link. Status Reg(0x00081A64) = 0x00000001
step 17: PEX5 pexUnit= 1
PEX5 : Detected No Link. Status Reg(0x00085A64) = 0x00000001
step 17: PEX6 pexUnit= 1
PEX6 : Detected No Link. Status Reg(0x00089A64) = 0x00000001
DDR3 Training Sequence - Ver 4.5.DDR3 Training Sequence - Static MC Init
DDR3 Training Sequence - HW Training Procedure
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12 (Feb 06 2014 - 17:14:13) Marvell version: v2011.12 2013_Q1.2
Boot version:v1.3.25
Board: RD-AXP-GP rev 1.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 256 MiB
Map: Code: 0x0fea7000:0x0ff5e2d4
BSS: 0x0ffefd80
Stack: 0x0f9a6ef8
Heap: 0x0f9a7000:0x0fea7000
NAND: Spansion 1Gb(ID=F101) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
#### auto_recovery ####
[u_env] get auto_recovery == no
[u_env] get auto_recovery == no
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:0, boot_part:2, boot_part_ready:3
PEX 0.0(0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1): Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.2(2): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.3(3): Detected No Link.
PEX 1.0(4): Detected No Link.
PEX 1.1(5): Detected No Link.
PEX 1.2(6): Detected No Link.
boot_end Offset: 0x100000
u_env_off Offset: 0x100000
s_env_off Offset: 0x140000
devinfo Offset: 0x900000
===================
total_badCount: 0
boot_badCount: 0
u_env_badCount: 0
s_env_badCount: 0
buff_badCount: 0
===================
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
mvEthE6171SwitchBasicInit finished
Net: mvSysNetaInit enter
set port 0 to rgmii enter
set port 1 to rgmii enter
egiga0 [PRIME], egiga1
modify Phy Status
auto_recovery_check changes bootcmd: run altnandboot
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x3200000, size 0x400000
4194304 bytes read: OK
## Booting kernel from Legacy Image at 02000000 ...
Image Name: DD-WRT
Created: 2015-12-29 4:13:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1750811 Bytes = 1.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.25 (root@seg-desktop) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r46799) ) #54 SMP Tue Dec 22 00:34:08 CET 2015
[ 0.000000] CPU: ARMv7 Processor [562f5842] revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine model: Linksys WRT1900AC (Mamba)
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 9 pages/cpu @cfdd8000 s6976 r8192 d21696 u36864
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=armada-nand:1024K(uboot)ro,256K(u_env),256K(s_env),1m@9m(devinfo),40m@10m(kernel),37m@13m(rootfs),40m@50m(alt_kernel),37m@53m(alt_rootfs),80m@10m(ubifs),-@90m(syscfg) root=/dev/mtdblock7 ro rootfstype=jffs2 init=/sbin/init
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 254504K/262144K available (3590K kernel code, 177K rwdata, 928K rodata, 224K init, 273K bss, 7640K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0471e44 (4520 kB)
[ 0.000000] .init : 0xc0472000 - 0xc04aa000 ( 224 kB)
[ 0.000000] .data : 0xc04aa000 - 0xc04d66a0 ( 178 kB)
[ 0.000000] .bss : 0xc04d66a0 - 0xc051aca0 ( 274 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] Aurora cache controller enabled, 32 ways, 2048 kB
[ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a69ef12
[ 0.000008] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798691800ns
[ 0.000246] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.040056] pid_max: default: 32768 minimum: 301
[ 0.040153] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040162] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040487] CPU: Testing write buffer coherency: ok
[ 0.040639] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043115] Setting up static identity map for 0x130a0 - 0x130f8
[ 0.043397] mvebu-soc-id: MVEBU SoC ID=0x7823, Rev=0x2
[ 0.043523] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.044358] Booting CPU 1
[ 0.044636] CPU1: Booted secondary processor
[ 0.080045] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.080105] Brought up 2 CPUs
[ 0.080119] SMP: Total of 2 processors activated (2382.23 BogoMIPS).
[ 0.080125] CPU: All CPU(s) started in SVC mode.
[ 0.080649] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6
[ 0.080834] pinctrl core: initialized pinctrl subsystem
[ 0.083634] NET: Registered protocol family 16
[ 0.083862] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.110068] cpuidle: using governor ladder
[ 0.141045] SCSI subsystem initialized
[ 0.142020] Switched to clocksource armada_370_xp_clocksource
[ 0.142745] NET: Registered protocol family 2
[ 0.143226] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.143251] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.143274] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.143311] TCP: reno registered
[ 0.143323] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.143341] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.143466] NET: Registered protocol family 1
[ 0.144392] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.145361] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 0.145382] msgmni has been set to 497
[ 0.146109] io scheduler noop registered
[ 0.146123] io scheduler deadline registered (default)
[ 0.146713] armada-xp-pinctrl f1018000.pin-ctrl: registered pinctrl driver
[ 0.147170] irq: Cannot allocate irq_descs @ IRQ39, assuming pre-allocated
[ 0.147480] irq: Cannot allocate irq_descs @ IRQ71, assuming pre-allocated
[ 0.147956] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 0.147971] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.147980] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff]
[ 0.147989] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.148445] PCI: bus0: Fast back to back transfers disabled
[ 0.148457] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148469] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148480] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148868] PCI: bus1: Fast back to back transfers disabled
[ 0.149298] PCI: bus2: Fast back to back transfers disabled
[ 0.149700] PCI: bus3: Fast back to back transfers disabled
[ 0.149818] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff]
[ 0.149830] pci 0000:00:02.0: BAR 8: assigned [mem 0xf8200000-0xf83fffff]
[ 0.149841] pci 0000:00:03.0: BAR 8: assigned [mem 0xf8400000-0xf85fffff]
[ 0.149853] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8007fff 64bit]
[ 0.149874] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.149886] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff]
[ 0.149900] pci 0000:02:00.0: BAR 0: assigned [mem 0xf8200000-0xf82fffff 64bit pref]
[ 0.149922] pci 0000:02:00.0: BAR 2: assigned [mem 0xf8300000-0xf83fffff 64bit pref]
[ 0.149942] pci 0000:00:02.0: PCI bridge to [bus 02]
[ 0.149952] pci 0000:00:02.0: bridge window [mem 0xf8200000-0xf83fffff]
[ 0.149965] pci 0000:03:00.0: BAR 0: assigned [mem 0xf8400000-0xf84fffff 64bit pref]
[ 0.149985] pci 0000:03:00.0: BAR 2: assigned [mem 0xf8500000-0xf85fffff 64bit pref]
[ 0.150003] pci 0000:00:03.0: PCI bridge to [bus 03]
[ 0.150013] pci 0000:00:03.0: bridge window [mem 0xf8400000-0xf85fffff]
[ 0.150057] pci 0000:00:01.0: enabling device (0140 -> 0142)
[ 0.150080] pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 0.150243] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.182101] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.222093] mv_xor f1060900.xor: Marvell XOR: ( xor cpy )
[ 0.222187] mv_xor f10f0900.xor: Marvell shared XOR driver
[ 0.262086] mv_xor f10f0900.xor: Marvell XOR: ( xor cpy )
[ 0.302086] mv_xor f10f0900.xor: Marvell XOR: ( xor cpy )
[ 0.302277] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.302737] console [ttyS0] disabled
[ 0.322745] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 19, base_baud = 15625000) is a 16550A
[ 0.982320] console [ttyS0] enabled
[ 0.986523] pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
[ 0.994141] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
[ 1.000514] nand: AMD/Spansion S34ML01G1
[ 1.004466] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 1.010147] pxa3xx-nand f10d0000.nand: ECC strength 16, ECC step size 2048
[ 1.017282] Bad block table found at page 65472, version 0x01
[ 1.023353] Bad block table found at page 65408, version 0x01
[ 1.029426] found commandline
[ 1.032425] rename part 7 to ubi
[ 1.035523] 10 ofpart partitions found on MTD device pxa3xx_nand-0
[ 1.041903] Creating 10 MTD partitions on "pxa3xx_nand-0":
[ 1.047429] 0x000000000000-0x000000100000 : "u-boot"
[ 1.052882] 0x000000100000-0x000000140000 : "u_env"
[ 1.058172] 0x000000140000-0x000000180000 : "s_env"
[ 1.063496] 0x000000900000-0x000000a00000 : "devinfo"
[ 1.068963] 0x000000a00000-0x000003200000 : "linux"
[ 1.074344] 0x000000d00000-0x000003200000 : "rootfs"
[ 1.079795] mtd: partition "rootfs" set to be root filesystem
[ 1.085728] split_squashfs: no squashfs found in "pxa3xx_nand-0"
[ 1.091755] 0x000003200000-0x000005900000 : "linux2"
[ 1.097249] 0x000003500000-0x000005900000 : "ubi"
[ 1.102457] 0x000005900000-0x000005940000 : "nvram"
[ 1.107774] 0x000005a00000-0x000007f00000 : "ddwrt"
[ 1.113700] m25p80 spi0.0: mr25h256 (32 Kbytes)
[ 1.118371] found commandline
[ 1.121347] rename part 7 to ubi
[ 1.125424] libphy: Fixed MDIO Bus: probed
[ 1.129721] tun: Universal TUN/TAP device driver, 1.6
[ 1.134802] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.141166] libphy: orion_mdio_bus: probed
[ 1.146565] mvneta f1070000.ethernet eth0: Using random mac address 32:fd:b3:92:10:74
[ 1.155626] mvneta f1074000.ethernet eth1: Using random mac address b2:ee:ad:e7:85:f0
[ 1.163573] PPP generic driver version 2.4.2
[ 1.167948] PPP BSD Compression module registered
[ 1.172703] PPP Deflate Compression module registered
[ 1.177778] PPP MPPE Compression module registered
[ 1.182596] NET: Registered protocol family 24
[ 1.187231] trying to register driver cpufreq-dt
[ 1.202037] driver cpufreq-dt up and running
[ 1.207676] GACT probability NOT on
[ 1.211195] Mirror/redirect action on
[ 1.214970] Simple TC action Loaded
[ 1.219338] netem: version 1.3
[ 1.222515] u32 classifier
[ 1.225239] Performance counters on
[ 1.229088] input device check on
[ 1.232806] Actions configured
[ 1.236290] Netfilter messages via NETLINK v0.30.
[ 1.241075] nf_conntrack version 0.5.0 (3976 buckets, 15904 max)
[ 1.247851] nf_conntrack_rtsp v0.6.21 loading
[ 1.252880] xt_time: kernel timezone is -0000
[ 1.257281] ip_set: protocol 6
[ 1.260642] gre: GRE over IPv4 demultiplexor driver
[ 1.265870] nf_nat_rtsp v0.6.21 loading
[ 1.269759] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.275381] TCP: bic registered
[ 1.278553] TCP: cubic registered
[ 1.281890] TCP: westwood registered
[ 1.285542] TCP: highspeed registered
[ 1.289233] TCP: hybla registered
[ 1.292620] TCP: htcp registered
[ 1.295876] TCP: vegas registered
[ 1.299213] TCP: veno registered
[ 1.302514] TCP: scalable registered
[ 1.306117] TCP: lp registered
[ 1.309193] TCP: yeah registered
[ 1.312491] TCP: illinois registered
[ 1.316098] NET: Registered protocol family 17
[ 1.320639] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.333399] Bridge firewalling registered
[ 1.337442] 8021q: 802.1Q VLAN Support v1.8
[ 1.341803] Registering SWP/SWPB emulation handler
[ 1.348107] searching for nvram
[ 1.351285] nvram size = -1069384950
[ 1.382724] UBI: auto-attach mtd7
[ 1.386075] UBI: attaching mtd7 to ubi0
[ 1.835645] UBI: scanning is finished
[ 1.883502] UBI: volume 1 ("rootfs_data") re-sized from 9 to 45 LEBs
[ 1.891202] UBI: attached mtd7 (name "ubi", size 36 MiB) to ubi0
[ 1.897293] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.904156] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.910885] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.917830] UBI: good PEBs: 288, bad PEBs: 0, corrupted PEBs: 0
[ 1.923823] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 1.930989] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1434344299
[ 1.940111] UBI: available PEBs: 0, total reserved PEBs: 288, PEBs reserved for bad PEB handling: 20
[ 1.949387] UBI: background thread "ubi_bgt0d" started, PID 398
[ 1.956143] UBI: ubiblock0_0 created from ubi0:0(rootfs)
[ 1.961886] mvsw61xx 1000000003.mvsw61xx: Found MV88E6172 at f1072004.mdio-mi:10
[ 1.969392] mvsw61xx 1000000003.mvsw61xx: Using direct addressing
[ 1.975741] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 2.012174] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.019748] Freeing unused kernel memory: 224K (c0472000 - c04aa000)
start service
starting Architecture code for mvebu
udevtrigger[414]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
[ 4.667889] orion_wdt: Initial timeout 171 sec, nowayout
[ 4.726904] i2c /dev entries driver
[ 5.184958] marvell-cesa: probe of f1090000.crypto failed with error -22
[ 5.220311] Loading modules backported from Linux version master-2015-12-03-0-g1677f62
[ 5.228294] Backport generated by backports.git backports-20151120-0-g906a6b3
[ 5.305082] cfg80211: World regulatory domain updated:
[ 5.310259] cfg80211: DFS Master region: unset
[ 5.314681] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 5.314692] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314697] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314701] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314706] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314710] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314715] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314719] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 5.314724] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 5.417308] random: nonblocking pool is initialized
[ 5.521993] <<Marvell 802.11ac Wireless Network Driver version 10.3.0.15-20151208>>
[ 5.529561] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 5.535481] mwlwifi 0000:02:00.0: enabling device (0140 -> 0142)
[ 6.593406] ieee80211 phy0: firmware version: 0x7020806
[ 6.613784] ieee80211 phy0: 2G enabled, 5G disabled
[ 6.618685] ieee80211 phy0: 4 TX antennas, 4 RX antennas
[ 6.624170] pci 0000:00:03.0: enabling device (0140 -> 0142)
[ 6.629884] mwlwifi 0000:03:00.0: enabling device (0140 -> 0142)
[ 7.645957] ieee80211 phy1: firmware version: 0x7020806
[ 7.669463] ieee80211 phy1: 2G disabled, 5G enabled
[ 7.674417] ieee80211 phy1: 4 TX antennas, 4 RX antennas
a_pEnv->crc = b0ea1192
crc32 = b0ea1192
count is already zero, no need to call again
cannot open /proc/irq/27/smp_affinity
[USB] checking...
umount: can't unmount /mnt: No such file or directory
Name: lan_ifname Value: br0
Name: lan_ifnames Value: eth0 eth1 ath0 ath1
Name: wan_ifname Value: eth1
Name: wan_ifname2 Value: eth1
Name: wan_ifnames Value: eth1
Name: wan_default Value: eth1
removing lockfile
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
ifconfig: invalid hw-addr
[ 11.260562] device br0 entered promiscuous mode
killall: ead: no process killed
[ 11.565699] device eth0 entered promiscuous mode
sh: [ 11.574917] device br0 left promiscuous mode
ead: not found
[ 11.582797] device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Address not available
[ 11.600209] device br0 left promiscuous mode
ath9k deconfigure_single: phy0 ath0
ath9k deconfigure_single: phy1 ath1
[ 11.634281] cfg80211: Regulatory domain changed to country: US
[ 11.640157] cfg80211: DFS Master region: FCC
[ 11.640158] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.640166] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.640171] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
[ 11.640176] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
[ 11.640180] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2300 mBm), (N/A)
[ 11.640184] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.640189] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 13.562164] mvneta f1070000.ethernet eth0: link up
[ 13.567013] br0: port 1(eth0) entered forwarding state
[ 13.572245] br0: port 1(eth0) entered forwarding state
resetbutton: factory default.
removing lockfile
send dhcp lease release signal
[ 15.572090] br0: port 1(eth0) entered forwarding state
ath9k configure_single: phy0 ath0
sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/chanbw: nonexistent directory
sh: can't create /sys/kernel/debug/ieee80211/phy0/ath9k/ani: nonexistent directory
command failed: Not supported (-95)
call mac80211autochannel for interface: ath0
Sending SIGTERM [ 16.008760] watchdog watchdog0: watchdog did not stop!
to all processes
Sending SIGKILL to all processes
unmounting /
unmounting /
[ 24.021878] reboot: Restarting system
BootROM 1.20
Booting from NAND flash
Step 1: First phase of PEX-PIPE Configuration
Step 2: Configure the desire PIN_PHY_GEN
Step 3 QSGMII enable
Step 4: Configure SERDES MUXes
Step 5: Activate the RX High Impedance Mode
Step 6: [PEX-Only] PEX-Main configuration (X4 or X1)
Step 6.2: [PEX-Only] PCI Express Link Capabilities
Step 7: [PEX-X4 Only] To create PEX-Link
Steps 7,8,9,10 and 11
Steps 12: [PEX-Only] Last phase of PEX-PIPE ConfigurationSteps 13: Wait 15ms before checking resultsSteps 14: [PEX-Only] In order to configureSteps 15: [PEX-Only] In order to configureSteps 16: [PEX-Only] Training Enablestep 17: max_if= 0x7
step 17: PEX0 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0050
mvPexConfigRead: return addr=0x%x0050
--> 7001
--> 7001
--> A005
--> A005
--> 0010
--> 4C12
Gen2 client!
step 17: PEX1 pexUnit= 0
step 17: PEX2 pexUnit= 0
** Link is Gen1, check the EP capability
--> 0040
mvPexConfigRead: return addr=0x%x0040
--> 5001
--> 5001
--> 7005
--> 7005
--> 0010
--> DC12
Gen2 client!
step 17: PEX3 pexUnit= 0
PEX3 : Detected No Link. Status Reg(0x0004DA64) = 0x00000001
step 17: PEX4 pexUnit= 1
PEX4 : Detected No Link. Status Reg(0x00081A64) = 0x00000001
step 17: PEX5 pexUnit= 1
PEX5 : Detected No Link. Status Reg(0x00085A64) = 0x00000001
step 17: PEX6 pexUnit= 1
PEX6 : Detected No Link. Status Reg(0x00089A64) = 0x00000001
DDR3 Training Sequence - Ver 4.5.DDR3 Training Sequence - Static MC Init
DDR3 Training Sequence - HW Training Procedure
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2011.12 (Feb 06 2014 - 17:14:13) Marvell version: v2011.12 2013_Q1.2
Boot version:v1.3.25
Board: RD-AXP-GP rev 1.0
SoC: MV78230 B0
running 2 CPUs
Custom configuration
CPU: Marvell PJ4B (584) v7 (Rev 2) LE
CPU 0
CPU @ 1200 [MHz]
L2 @ 600 [MHz]
TClock @ 250 [MHz]
DDR @ 600 [MHz]
DDR 32Bit Width, FastPath Memory Access
DDR ECC Disabled
DRAM: 256 MiB
Map: Code: 0x0fea7000:0x0ff5e2d4
BSS: 0x0ffefd80
Stack: 0x0f9a6ef8
Heap: 0x0f9a7000:0x0fea7000
NAND: Spansion 1Gb(ID=F101) 128 MiB
MMC: MRVL_MMC: 0
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
#### auto_recovery ####
[u_env] get auto_recovery == yes
[u_env] get auto_recovery == yes
[u_env] get boot_part == 2
[u_env] get boot_part_ready == 3
auto_recovery enabled:1, boot_part:2, boot_part_ready:3
[boot_count_read] block:0x140000, size:256KB, records:128
[boot_count_read_record] boot_count:0, next_record:17
[boot_count_write] erase:0, auto_recovery->block_offset:0x140000
Updating boot_count ...
[boot_count_write] offset:0x148800 , length:2048
done
PEX 0.0(0): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.1(1): Root Complex Interface, Detected Link X1, GEN 1.1
PEX 0.2(2): Root Complex Interface, Detected Link X1, GEN 2.0
PEX 0.3(3): Detected No Link.
PEX 1.0(4): Detected No Link.
PEX 1.1(5): Detected No Link.
PEX 1.2(6): Detected No Link.
boot_end Offset: 0x100000
u_env_off Offset: 0x100000
s_env_off Offset: 0x140000
devinfo Offset: 0x900000
===================
total_badCount: 0
boot_badCount: 0
u_env_badCount: 0
s_env_badCount: 0
buff_badCount: 0
===================
FPU initialized to Run Fast Mode.
USB 0: Host Mode
USB 1: Host Mode
USB 2: Device Mode
Modules Detected:
mvEthE6171SwitchBasicInit finished
Net: mvSysNetaInit enter
set port 0 to rgmii enter
set port 1 to rgmii enter
egiga0 [PRIME], egiga1
modify Phy Status
auto_recovery_check changes bootcmd: run altnandboot
Hit any key to stop autoboot: 0
Marvell>>