Hi everyone,
I just succeed to install OpenWRT mainline on Clearfog router board from SolidRun. Works fine, except mini-PCIe WiFi modules from Compex: WLE900VX on Qualcomm-Atheros QCA9880. As I seen on lots of posts I'm not the only one in this case and the router board or the WiFi module aren't the problem.
I wrote a full step-by-step tutorial to build and install OpenWRT on the board:
forum.solid-run.com/viewtopic.php?f=34&t=3287&p=22116#p22116
On the .config file the following selected items are checked:
CONFIG_PACKAGE_ath10k-firmware-qca988x=y
CONFIG_PACKAGE_ATH_DFS=y
CONFIG_PACKAGE_kmod-ath10k=yWhen I'm booting the board I got some errors about this firmware:
[ 13.293644] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 13.300102] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 13.479283] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 13.490021] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.500372] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 13.509486] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 13.519883] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.530035] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 13.554585] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 13.563863] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 13.573874] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 13.622787] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 13.633259] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.643895] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 13.656918] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 13.867871] hidraw: raw HID events driver (C) Jiri Kosina
[ 14.795986] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 14.886825] pci 0000:00:03.0: enabling device (0140 -> 0142)
[ 14.892536] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 14.899002] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 15.074278] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 15.085014] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.095334] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 15.104430] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[ 15.114820] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.125559] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 15.134298] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 15.143554] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 15.153363] ath10k_pci 0000:02:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 15.202285] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 15.212756] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.223094] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 15.232409] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08Then the lspci command returns informations on both modules:
root@OpenWrt:/# lspci
00:02.0 Class 0604: 11ab:6828
00:03.0 Class 0604: 11ab:6828
01:00.0 Class 0280: 168c:003c
02:00.0 Class 0280: 168c:003cFull boot log:
BootROM - 1.73
Booting from MMC
General initialization - Version: 1.0.0
Detected Device ID 6828
High speed PHY - Version: 2.0
Init Customer board board SerDes lanes topology details:
| Lane # | Speed| Type |
------------------------------|
| 0 | 3 | SATA0 |
| 1 | 0 | SGMII1 |
| 2 | 5 | PCIe1 |
| 3 | 5 | USB3 HOST1 |
| 4 | 5 | PCIe2 |
| 5 | 0 | SGMII2 |
-------------------------------
PCIe, Idx 1: detected no link
PCIe, Idx 2: detected no link
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver TIP-1.39.0
DDR3 Training Sequence - Switching XBAR Window to FastPath Window
DDR3 Training Sequence - Ended Successfully
BootROM: Image checksum verification PASSED
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** LOADER **
U-Boot 2013.01-g1e88e63-dirty (Jul 20 2016 - 21:38:48) Marvell version: 2015_T1.0p11
Board: A38x-Customer-Board-1
SoC: MV88F6828 Rev A0
running 2 CPUs
CPU: ARM Cortex A9 MPCore (Rev 1) LE
CPU 0
CPU @ 1332 [MHz]
L2 @ 666 [MHz]
TClock @ 250 [MHz]
DDR3 @ 666 [MHz]
DDR3 32 Bit Width,FastPath Memory Access, DLB Enabled, ECC Disabled
DRAM: 1 GiB
MMC: mv_sdh: 0
sdhci_transfer_data: Error detected in status(0x408000)!
PCI-e 1 (IF 0 - bus 0) Root Complex Interface, Detected Link X1, GEN 1.1
PCI-e 2 (IF 1 - bus 1) Root Complex Interface, Detected Link X1, GEN 1.1
USB2.0 0: Host Mode
USB3.0 0: Host Mode
USB3.0 1: Host Mode
Map: Code: 0x3fed3000:0x3ff978bc
BSS: 0x3ffef564
Stack: 0x3f9c2f20
Heap: 0x3f9c3000:0x3fed3000
U-Boot Environment: 0x000f0000:0x00100000 (MMC)
Board configuration detected:
Register 20 is = 0xffff
Writing 0xfff9 to register 20
Verifying value - 0xffff
Port1: phyAddr=0x1, Not Marvell PHY id1 ffff id2 ffff
PHY error - shutdown port1
Net:
| port | Interface | PHY address |
|--------|-----------|--------------|
| egiga0 | RGMII | 0x00 |
| egiga1 | SGMII | 0x01 |
| egiga2 | SGMII | In-Band |
egiga0 [PRIME], egiga1, egiga2
Hit any key to stop autoboot: 0
18588 bytes read in 17 ms (1 MiB/s)
2277252 bytes read in 133 ms (16.3 MiB/s)
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x01000000
Loading Device Tree to 00ff8000, end 00fff89b ... OK
Skipping Device Tree update ('fdt_skip_update' = yes)
Limit DDR size at 3GB due to power of 2 requirement of Address decoding
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.14 (jcd@jcdserveri7b) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50104) ) #83 SMP Thu Jun 8 14:51:03 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: SolidRun Clearfog A1
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] PERCPU: Embedded 12 pages/cpu @cfdd1000 s17984 r8192 d22976 u49152
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: rootfstype=ext4 root=/dev/mmcblk0p1 rw console=ttyS0,115200 rootwait
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 252760K/262144K available (4532K kernel code, 187K rwdata, 1628K rodata, 268K init, 299K bss, 9384K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc060c3d4 (6161 kB)
[ 0.000000] .init : 0xc060d000 - 0xc0650000 ( 268 kB)
[ 0.000000] .data : 0xc0650000 - 0xc067edb4 ( 188 kB)
[ 0.000000] .bss : 0xc067edb4 - 0xc06c9cec ( 300 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] mvebu_mbus: [Firmware Warn]: deprecated mbus-mvebu Device Tree, suspend/resume will not work
[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9
[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[ 0.000000] L2C-310 D prefetch enabled, offset 1 lines
[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 1024 kB
[ 0.000000] L2C-310 Coherent: CACHE_ID 0x410054c9, AUX_CTRL 0x56070001
[ 0.000000] Switching to timer-based delay loop, resolution 40ns
[ 0.000003] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 85899345900ns
[ 0.000011] clocksource: armada_370_xp_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 76450417870 ns
[ 0.000161] Console: colour dummy device 80x30
[ 0.000172] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=250000)
[ 0.000180] pid_max: default: 32768 minimum: 301
[ 0.000220] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000226] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000446] CPU: Testing write buffer coherency: ok
[ 0.000565] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.000593] Setting up static identity map for 0x8280 - 0x82d8
[ 0.000692] mvebu-soc-id: MVEBU SoC ID=0x6828, Rev=0x4
[ 0.000792] mvebu-pmsu: Initializing Power Management Service Unit
[ 0.001262] Booting CPU 1
[ 0.001458] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.001489] Brought up 2 CPUs
[ 0.001496] SMP: Total of 2 processors activated (100.00 BogoMIPS).
[ 0.001499] CPU: All CPU(s) started in SVC mode.
[ 0.003540] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.003629] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.003673] pinctrl core: initialized pinctrl subsystem
[ 0.004048] NET: Registered protocol family 16
[ 0.004623] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.029882] cpuidle: using governor ladder
[ 0.033040] mvebu-pmsu: CPU hotplug support is currently broken on Armada 38x: disabling
[ 0.033051] mvebu-pmsu: CPU idle is currently broken on Armada 38x: disabling
[ 0.060712] SCSI subsystem initialized
[ 0.060936] usbcore: registered new interface driver usbfs
[ 0.060967] usbcore: registered new interface driver hub
[ 0.060995] usbcore: registered new device driver usb
[ 0.061602] clocksource: Switched to clocksource armada_370_xp_clocksource
[ 0.063723] NET: Registered protocol family 2
[ 0.063991] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.064010] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.064031] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.064060] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.064075] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.064150] NET: Registered protocol family 1
[ 0.064660] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.067808] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.067818] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.068744] io scheduler noop registered
[ 0.068753] io scheduler deadline registered (default)
[ 0.069233] armada-38x-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.069620] irq: Cannot allocate irq_descs @ IRQ50, assuming pre-allocated
[ 0.069780] irq: Cannot allocate irq_descs @ IRQ82, assuming pre-allocated
[ 0.070133] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.112148] mv_xor f1060800.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.112254] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.152119] mv_xor f1060900.xor: Marvell XOR (Descriptor Mode): ( xor cpy intr )
[ 0.152297] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.152670] console [ttyS0] disabled
[ 0.172746] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 23, base_baud = 15625000) is a 16550A
[ 0.730262] console [ttyS0] enabled
[ 0.754059] f1012100.serial: ttyS1 at MMIO 0xf1012100 (irq = 24, base_baud = 15625000) is a 16550A
[ 0.763454] ahci-mvebu f10a8000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.772536] ahci-mvebu f10a8000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.782076] scsi host0: ahci-mvebu
[ 0.785678] scsi host1: ahci-mvebu
[ 0.789196] ata1: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x100 irq 45
[ 0.797146] ata2: SATA max UDMA/133 mmio [mem 0xf10a8000-0xf10a9fff] port 0x180 irq 45
[ 0.805194] ahci-mvebu f10e0000.sata: AHCI 0001.0000 32 slots 2 ports 6 Gbps 0x3 impl platform mode
[ 0.814275] ahci-mvebu f10e0000.sata: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs
[ 0.823871] scsi host2: ahci-mvebu
[ 0.827460] scsi host3: ahci-mvebu
[ 0.830966] ata3: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x100 irq 46
[ 0.838917] ata4: SATA max UDMA/133 mmio [mem 0xf10e0000-0xf10e1fff] port 0x180 irq 46
[ 0.848030] libphy: Fixed MDIO Bus: probed
[ 0.852282] libphy: orion_mdio_bus: probed
[ 0.857694] mvneta f1030000.ethernet eth0: Using random mac address 0a:f3:cf:7d:aa:bf
[ 0.866505] mvneta f1034000.ethernet eth1: Using random mac address 62:c8:8d:e1:35:3f
[ 0.875252] mvneta f1070000.ethernet eth2: Using random mac address 92:c0:d6:0f:1e:1d
[ 0.883172] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.889716] ehci-pci: EHCI PCI platform driver
[ 0.894210] ehci-platform: EHCI generic platform driver
[ 0.899554] ehci-orion: EHCI orion driver
[ 0.903664] orion-ehci f1058000.usb: EHCI Host Controller
[ 0.909087] orion-ehci f1058000.usb: new USB bus registered, assigned bus number 1
[ 0.916749] orion-ehci f1058000.usb: irq 40, io mem 0xf1058000
[ 0.941617] orion-ehci f1058000.usb: USB 2.0 started, EHCI 1.00
[ 0.947834] hub 1-0:1.0: USB hub found
[ 0.951623] hub 1-0:1.0: 1 port detected
[ 0.955899] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 0.961232] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 2
[ 0.968849] xhci-hcd f10f0000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 0.977420] xhci-hcd f10f0000.usb3: irq 48, io mem 0xf10f0000
[ 0.983442] hub 2-0:1.0: USB hub found
[ 0.987213] hub 2-0:1.0: 1 port detected
[ 0.991246] xhci-hcd f10f0000.usb3: xHCI Host Controller
[ 0.996586] xhci-hcd f10f0000.usb3: new USB bus registered, assigned bus number 3
[ 1.004127] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.012480] hub 3-0:1.0: USB hub found
[ 1.016251] hub 3-0:1.0: 1 port detected
[ 1.020321] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.025663] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 4
[ 1.033269] xhci-hcd f10f8000.usb3: hcc params 0x0a000990 hci version 0x100 quirks 0x00010010
[ 1.041841] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[ 1.047850] hub 4-0:1.0: USB hub found
[ 1.051649] hub 4-0:1.0: 1 port detected
[ 1.055675] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 1.061004] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 1.068556] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.076895] hub 5-0:1.0: USB hub found
[ 1.080668] hub 5-0:1.0: 1 port detected
[ 1.084832] usbcore: registered new interface driver usb-storage
[ 1.091021] armada38x-rtc f10a3800.rtc: rtc core: registered f10a3800.rtc as rtc0
[ 1.098689] i2c /dev entries driver
[ 1.113190] orion_wdt: Initial timeout 171 sec
[ 1.117816] sdhci: Secure Digital Host Controller Interface driver
[ 1.124019] sdhci: Copyright(c) Pierre Ossman
[ 1.128568] sdhci-pxav3 f10d8000.sdhci: Got CD GPIO
[ 1.133508] sdhci-pxav3 f10d8000.sdhci: No vmmc regulator found
[ 1.139442] sdhci-pxav3 f10d8000.sdhci: No vqmmc regulator found
[ 1.151620] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.157052] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.181613] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.187038] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.192522] mmc0: SDHCI controller on f10d8000.sdhci [f10d8000.sdhci] using ADMA
[ 1.199982] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.209539] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 1.217333] NET: Registered protocol family 10
[ 1.222380] NET: Registered protocol family 17
[ 1.226863] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.239521] 8021q: 802.1Q VLAN Support v1.8
[ 1.243808] Registering SWP/SWPB emulation handler
[ 1.249513] armada38x-rtc f10a3800.rtc: setting system clock to 2106-02-07 06:26:55 UTC (4294967215)
[ 1.259692] Waiting for root device /dev/mmcblk0p1...
[ 1.295793] mmc0: MAN_BKOPS_EN bit is not set
[ 1.304855] mmc0: new high speed MMC card at address 0001
[ 1.310516] mmcblk0: mmc0:0001 DF4064 58.2 GiB
[ 1.315149] mmcblk0boot0: mmc0:0001 DF4064 partition 1 4.00 MiB
[ 1.321151] mmcblk0boot1: mmc0:0001 DF4064 partition 2 4.00 MiB
[ 1.327157] mmcblk0rpmb: mmc0:0001 DF4064 partition 3 4.00 MiB
[ 1.334472] mmcblk0: p1 p2
[ 1.372079] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 1.380543] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[ 1.401934] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 1.410057] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 1.416255] Freeing unused kernel memory: 268K (c060d000 - c0650000)
[ 1.511668] init: Console is alive
[ 1.515153] init: - watchdog -
[ 1.541667] usb 5-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 1.562584] usb-storage 5-1:1.0: USB Mass Storage device detected
[ 1.568906] usb-storage 5-1:1.0: Quirks match for vid 174c pid 55aa: 400000
[ 1.575956] scsi host4: usb-storage 5-1:1.0
[ 1.835793] Uniform Multi-Platform E-IDE driver
[ 1.860793] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 2.571897] scsi 4:0:0:0: Direct-Access ASMT 2115 0 PQ: 0 ANSI: 6
[ 2.580644] sd 4:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 2.588303] random: procd urandom read with 12 bits of entropy available
[ 2.595049] sd 4:0:0:0: [sda] Write Protect is off
[ 2.600037] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.615102] sd 4:0:0:0: [sda] Attached SCSI disk
[ 4.960324] mount_root: mounting /dev/root
[ 4.964976] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[ 4.970455] mount_root: loading kmods from internal overlay
[ 5.022901] block: attempting to load /etc/config/fstab
[ 5.029439] block: extroot: not configured
[ 5.041064] procd: - early -
[ 5.043997] procd: - watchdog -
[ 5.620865] procd: - ubus -
[ 5.774063] procd: - init -
Please press Enter to activate this console.
[ 6.459967] md: linear personality registered for level -1
[ 6.467862] md: raid0 personality registered for level 0
[ 6.474683] md: raid1 personality registered for level 1
[ 6.483251] md: raid10 personality registered for level 10
[ 6.489606] async_tx: api initialized (async)
[ 6.494502] xor: measuring software checksum speed
[ 6.591595] arm4regs : 2102.400 MB/sec
[ 6.691593] 8regs : 1618.800 MB/sec
[ 6.791591] 32regs : 1672.400 MB/sec
[ 6.795783] xor: using function: arm4regs (2102.400 MB/sec)
[ 6.971906] raid6: int32x1 gen() 127 MB/s
[ 7.141603] raid6: int32x1 xor() 140 MB/s
[ 7.311887] raid6: int32x2 gen() 199 MB/s
[ 7.481694] raid6: int32x2 xor() 174 MB/s
[ 7.651614] raid6: int32x4 gen() 216 MB/s
[ 7.821652] raid6: int32x4 xor() 166 MB/s
[ 7.991777] raid6: int32x8 gen() 309 MB/s
[ 8.161672] raid6: int32x8 xor() 172 MB/s
[ 8.165951] raid6: using algorithm int32x8 gen() 309 MB/s
[ 8.171360] raid6: .... xor() 172 MB/s, rmw enabled
[ 8.176253] raid6: using intx1 recovery algorithm
[ 8.183216] md: raid6 personality registered for level 6
[ 8.188544] md: raid5 personality registered for level 5
[ 8.193888] md: raid4 personality registered for level 4
[ 8.204202] md: multipath personality registered for level -4
[ 8.211393] aoe: AoE v85 initialised.
[ 8.216736] NET: Registered protocol family 8
[ 8.221105] NET: Registered protocol family 20
[ 8.228383] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 8.244430] loop: module loaded
[ 8.249687] nbd: registered device at major 43
[ 8.258803] tun: Universal TUN/TAP device driver, 1.6
[ 8.263899] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.276292] ipip: IPv4 over IPv4 tunneling driver
[ 8.284200] l2tp_core: L2TP core driver, V2.0
[ 8.288954] l2tp_netlink: L2TP netlink interface
[ 8.297448] gre: GRE over IPv4 demultiplexor driver
[ 8.302908] ip_gre: GRE over IPv4 tunneling driver
[ 8.310360] PPP generic driver version 2.4.2
[ 8.317584] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.332718] nf_conntrack version 0.5.0 (3953 buckets, 15812 max)
[ 9.452306] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 9.632108] Netfilter messages via NETLINK v0.30.
[ 9.637751] ip_set: protocol 6
[ 12.677455] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
[ 12.685066] Backport generated by backports.git backports-20160216-0-ge3c56e4
[ 13.257861] GPIO line 496 (pcie1.0-clkreq) hogged as input
[ 13.263989] GPIO line 499 (pcie1.0-w-disable) hogged as output/low
[ 13.270484] GPIO line 500 (pcie2.0-clkreq) hogged as input
[ 13.276603] GPIO line 503 (pcie2.0-w-disable) hogged as output/low
[ 13.283108] GPIO line 501 (usb3-current-limit) hogged as input
[ 13.289566] GPIO line 502 (usb3-power) hogged as output/high
[ 13.295856] GPIO line 507 (m.2 devslp) hogged as output/low
[ 13.301741] GPIO line 508 (sfp-los) hogged as input
[ 13.306930] GPIO line 509 (sfp-tx-fault) hogged as input
[ 13.312873] GPIO line 510 (sfp-tx-disable) hogged as output/low
[ 13.319105] GPIO line 511 (sfp-mod-def0) hogged as input
[ 13.324486] pca953x 0-0020: interrupt support not compiled in
[ 13.330324] mvebu-pcie soc:pcie-controller: /soc/pcie-controller/pcie@2,0: reset gpio is active low
[ 13.340080] mvebu-pcie soc:pcie-controller: /soc/pcie-controller/pcie@3,0: reset gpio is active low
[ 13.401715] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00
[ 13.408611] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 13.414912] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 13.421811] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 13.427551] PCI: bus0: Fast back to back transfers disabled
[ 13.433147] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 13.441172] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 13.449484] PCI: bus1: Fast back to back transfers disabled
[ 13.455358] PCI: bus2: Fast back to back transfers disabled
[ 13.461006] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[ 13.467822] pci 0000:00:03.0: BAR 8: assigned [mem 0xe0400000-0xe06fffff]
[ 13.474635] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit]
[ 13.481974] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0200000-0xe020ffff pref]
[ 13.489214] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 13.494197] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe02fffff]
[ 13.501005] pci 0000:02:00.0: BAR 0: assigned [mem 0xe0400000-0xe05fffff 64bit]
[ 13.508343] pci 0000:02:00.0: BAR 6: assigned [mem 0xe0600000-0xe060ffff pref]
[ 13.515586] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 13.520563] pci 0000:00:03.0: bridge window [mem 0xe0400000-0xe06fffff]
[ 13.527858] pci 0000:00:02.0: enabling device (0140 -> 0142)
[ 13.533562] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 13.540039] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 13.719283] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
[ 13.730020] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.740251] firmware ath10k!pre-cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 13.749366] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/cal-pci-0000:01:00.0.bin failed with error -2
[ 13.759763] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.769926] firmware ath10k!cal-pci-0000:01:00.0.bin: firmware_loading_store: map pages failed
[ 13.795280] ath10k_pci 0000:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 13.804561] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 13.814591] ath10k_pci 0000:01:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 13.863520] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 13.873992] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 13.884377] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 13.897232] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 14.127791] hidraw: raw HID events driver (C) Jiri Kosina
[ 14.402334] sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 15.037314] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 15.127023] pci 0000:00:03.0: enabling device (0140 -> 0142)
[ 15.132764] ath10k_pci 0000:02:00.0: enabling device (0140 -> 0142)
[ 15.139290] ath10k_pci 0000:02:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 15.314244] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
[ 15.324982] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.335213] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 15.344347] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/cal-pci-0000:02:00.0.bin failed with error -2
[ 15.354739] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.365302] firmware ath10k!cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
[ 15.374044] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
[ 15.383300] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 1
[ 15.393387] ath10k_pci 0000:02:00.0: firmware ver 10.2.4.97 api 5 features no-p2p crc32 f91e34f2
[ 15.442548] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
[ 15.453020] ath10k_pci 0000:02:00.0: Falling back to user helper
[ 15.463437] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
[ 15.472250] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
[ 16.211989] u32 classifier
[ 16.214705] input device check on
[ 16.218373] Actions configured
[ 16.621908] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1
[ 16.642060] Mirror/redirect action on
[ 20.157786] fuse init (API version 7.23)
[ 20.374293] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 20.382636] ctnetlink v0.93: registering with nfnetlink.
[ 20.573789] PPP MPPE Compression module registered
[ 20.579086] NET: Registered protocol family 24
[ 20.584061] PPTP driver version 0.8.5
[ 20.592791] usbcore: registered new interface driver usbserial
[ 20.598672] usbcore: registered new interface driver usbserial_generic
[ 20.605252] usbserial: USB Serial support registered for generic
[ 20.622058] xt_time: kernel timezone is -0000
[ 20.628238] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 20.637756] usbcore: registered new interface driver sierra
[ 20.643393] usbserial: USB Serial support registered for Sierra USB modem
[ 20.650784] usbcore: registered new interface driver sierra_net
[ 22.709908] random: nonblocking pool is initialized
[ 23.203990] device eth0 entered promiscuous mode
[ 23.209751] br-lan: port 1(eth0) entered forwarding state
[ 23.215206] br-lan: port 1(eth0) entered forwarding state
[ 23.230688] device eth1 entered promiscuous mode
[ 23.235576] br-lan: port 2(eth1) entered forwarding state
[ 23.241015] br-lan: port 2(eth1) entered forwarding state
[ 23.254630] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 24.191724] br-lan: port 1(eth0) entered disabled state
[ 24.197053] br-lan: port 2(eth1) entered disabled state
[ 25.201621] mvneta f1030000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[ 25.209487] br-lan: port 1(eth0) entered forwarding state
[ 25.214927] br-lan: port 1(eth0) entered forwarding state
[ 25.221614] mvneta f1034000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off
[ 25.229472] br-lan: port 2(eth1) entered forwarding state
[ 25.234901] br-lan: port 2(eth1) entered forwarding state
[ 27.211598] br-lan: port 1(eth0) entered forwarding state
[ 27.231597] br-lan: port 2(eth1) entered forwarding state
[ 28.252019] mvneta f1070000.ethernet eth2: Link is Up - 1Gbps/Full - flow control off
[ 28.259878] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 39.155421] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 42.131605] ath10k_pci 0000:01:00.0: bss channel survey timed out
[ 45.131604] ath10k_pci 0000:01:00.0: bss channel survey timed out
[ 48.131606] ath10k_pci 0000:02:00.0: bss channel survey timed out
[ 51.131605] ath10k_pci 0000:02:00.0: bss channel survey timed out
BusyBox v1.24.2 () built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
DESIGNATED DRIVER (Bleeding Edge, 50104)
-----------------------------------------------------
* 2 oz. Orange Juice Combine all juices in a
* 2 oz. Pineapple Juice tall glass filled with
* 2 oz. Grapefruit Juice ice, stir well.
* 2 oz. Cranberry Juice
-----------------------------------------------------
root@OpenWrt:/# Any help? Thanks!