Hi, everyone.
I upload this information.
The files were updated.
---
target/linux/brcm2708/base-files/etc/board.d/02_network
target/linux/brcm2708/base-files/etc/diag.sh
target/linux/brcm2708/base-files/lib/brcm2708.sh
target/linux/brcm2708/image/Makefile
target/linux/brcm2708/patches-4.4/0391-BCM270X_DT-Add-bcm2708-rpi-0-w.dts.patch
package/kernel/brcm2708-gpu-fw/Makefile
package/base-files/files/etc/rc.local
---
Details of the update (patch) are as follows.
---
--- a/target/linux/brcm2708/base-files/etc/board.d/02_network
+++ b/target/linux/brcm2708/base-files/etc/board.d/02_network
@@ -11,6 +11,9 @@
board=$(brcm2708_board_name)
case "$board" in
+rpi-0-w)
+ ucidef_set_interface_lan "wlan0"
+ ;;
rpi-b |\
rpi-b-plus |\
rpi-2-b |\
--- a/target/linux/brcm2708/base-files/etc/diag.sh
+++ b/target/linux/brcm2708/base-files/etc/diag.sh
@@ -8,7 +8,8 @@
case "$(brcm2708_board_name)" in
rpi-b |\
rpi-cm |\
- rpi-zero)
+ rpi-zero |\
+ rpi-0-w)
status_led="led0"
;;
rpi-b-plus |\
--- a/target/linux/brcm2708/base-files/lib/brcm2708.sh
+++ b/target/linux/brcm2708/base-files/lib/brcm2708.sh
@@ -21,6 +21,9 @@
"Raspberry Pi Zero Rev"*)
board_name="rpi-zero"
;;
+ "Raspberry Pi Zero W Rev"*)
+ board_name="rpi-0-w"
+ ;;
"Raspberry Pi 2 Model B Rev"*)
board_name="rpi-2-b"
;;
--- a/target/linux/brcm2708/image/Makefile
+++ b/target/linux/brcm2708/image/Makefile
@@ -68,7 +68,7 @@
### BCM2708/BCM2835 ###
ifeq ($(SUBTARGET),bcm2708)
# Raspberry Pi Models B/B+/CM
- $(eval $(call bcm27xx,RaspberryPi,rpi,bcm2708-rpi-b bcm2708-rpi-b-plus bcm2708-rpi-cm))
+ $(eval $(call bcm27xx,RaspberryPi,rpi,bcm2708-rpi-b bcm2708-rpi-b-plus bcm2708-rpi-cm bcm2708-rpi-0-w))
endif
### BCM2709/BCM2836 ###
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.4/0391-BCM270X_DT-Add-bcm2708-rpi-0-w.dts.patch
@@ -0,0 +1,213 @@
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -3,6 +3,7 @@
+ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b.dtb
+ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-b-plus.dtb
+ dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-cm.dtb
++dtb-$(CONFIG_ARCH_BCM2708) += bcm2708-rpi-0-w.dtb
+ dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-cm.dtb
+ dtb-$(CONFIG_ARCH_BCM2709) += bcm2709-rpi-2-b.dtb
+ dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb
+--- /dev/null
++++ b/arch/arm/boot/dts/bcm2708-rpi-0-w.dts
+@@ -0,0 +1,200 @@
++/dts-v1/;
++
++#include "bcm2708.dtsi"
++
++/ {
++ compatible = "brcm,bcm2708";
++ model = "Raspberry Pi Zero W";
++};
++
++&gpio {
++ sdhost_pins: sdhost_pins {
++ brcm,pins = <48 49 50 51 52 53>;
++ brcm,function = <4>; /* alt0 */
++ };
++
++ spi0_pins: spi0_pins {
++ brcm,pins = <9 10 11>;
++ brcm,function = <4>; /* alt0 */
++ };
++
++ spi0_cs_pins: spi0_cs_pins {
++ brcm,pins = <8 7>;
++ brcm,function = <1>; /* output */
++ };
++
++ i2c0_pins: i2c0 {
++ brcm,pins = <0 1>;
++ brcm,function = <4>;
++ };
++
++ i2c1_pins: i2c1 {
++ brcm,pins = <2 3>;
++ brcm,function = <4>;
++ };
++
++ i2s_pins: i2s {
++ brcm,pins = <18 19 20 21>;
++ brcm,function = <4>; /* alt0 */
++ };
++
++ sdio_pins: sdio_pins {
++ brcm,pins = <34 35 36 37 38 39>;
++ brcm,function = <7 7 7 7 7 7>; /* ALT3 = SD1 */
++ brcm,pull = <0 2 2 2 2 2>;
++ };
++
++ bt_pins: bt_pins {
++ brcm,pins = <43>;
++ brcm,function = <4>; /* alt0:GPCLK2 */
++ brcm,pull = <0>; /* none */
++ };
++
++ uart0_pins: uart0_pins {
++ brcm,pins = <30 31 32 33>;
++ brcm,function = <7>; /* alt3=UART0 */
++ brcm,pull = <2 0 0 2>; /* up none none up */
++ };
++
++ uart1_pins: uart1_pins {
++ brcm,pins;
++ brcm,function;
++ brcm,pull;
++ };
++
++ audio_pins: audio_pins {
++ brcm,pins = <>;
++ brcm,function = <>;
++ };
++};
++
++&sdhost {
++ pinctrl-names = "default";
++ pinctrl-0 = <&sdhost_pins>;
++ bus-width = <4>;
++ status = "okay";
++};
++
++&mmc {
++ pinctrl-names = "default";
++ pinctrl-0 = <&sdio_pins>;
++ non-removable;
++ bus-width = <4>;
++ status = "okay";
++};
++
++&fb {
++ status = "okay";
++};
++
++&uart0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart0_pins &bt_pins>;
++ status = "okay";
++};
++
++&uart1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&uart1_pins>;
++ status = "okay";
++};
++
++&spi0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>;
++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>;
++
++ spidev0: spidev@0{
++ compatible = "spidev";
++ reg = <0>; /* CE0 */
++ #address-cells = <1>;
++ #size-cells = <0>;
++ spi-max-frequency = <500000>;
++ };
++
++ spidev1: spidev@1{
++ compatible = "spidev";
++ reg = <1>; /* CE1 */
++ #address-cells = <1>;
++ #size-cells = <0>;
++ spi-max-frequency = <500000>;
++ };
++};
++
++&i2c0 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c0_pins>;
++ clock-frequency = <100000>;
++};
++
++&i2c1 {
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2c1_pins>;
++ clock-frequency = <100000>;
++};
++
++&i2c2 {
++ clock-frequency = <100000>;
++};
++
++&i2s {
++ #sound-dai-cells = <0>;
++ pinctrl-names = "default";
++ pinctrl-0 = <&i2s_pins>;
++};
++
++&random {
++ status = "okay";
++};
++
++&leds {
++ act_led: act {
++ label = "led0";
++ linux,default-trigger = "mmc0";
++ gpios = <&gpio 47 0>;
++ };
++};
++
++&hdmi {
++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
++};
++
++&audio {
++ pinctrl-names = "default";
++ pinctrl-0 = <&audio_pins>;
++};
++
++/ {
++ chosen {
++ bootargs = "8250.nr_uarts=1";
++ };
++};
++
++/ {
++ __overrides__ {
++ uart0 = <&uart0>,"status";
++ uart0_clkrate = <&clk_uart0>,"clock-frequency:0";
++ uart1 = <&uart1>,"status";
++ i2s = <&i2s>,"status";
++ spi = <&spi0>,"status";
++ i2c0 = <&i2c0>,"status";
++ i2c1 = <&i2c1>,"status";
++ i2c2_iknowwhatimdoing = <&i2c2>,"status";
++ i2c0_baudrate = <&i2c0>,"clock-frequency:0";
++ i2c1_baudrate = <&i2c1>,"clock-frequency:0";
++ i2c2_baudrate = <&i2c2>,"clock-frequency:0";
++ core_freq = <&clk_core>,"clock-frequency:0";
++
++ act_led_gpio = <&act_led>,"gpios:4";
++ act_led_activelow = <&act_led>,"gpios:8";
++ act_led_trigger = <&act_led>,"linux,default-trigger";
++
++ audio = <&audio>,"status";
++ watchdog = <&watchdog>,"status";
++ random = <&random>,"status";
++ sd_overclock = <&sdhost>,"brcm,overclock-50:0";
++ sd_force_pio = <&sdhost>,"brcm,force-pio?";
++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0";
++ sd_debug = <&sdhost>,"brcm,debug";
++ };
++};
--- a/package/kernel/brcm2708-gpu-fw/Makefile
+++ b/package/kernel/brcm2708-gpu-fw/Makefile
@@ -1,5 +1,6 @@
#
# Copyright (C) 2012-2016 OpenWrt.org
+# Copyright (C) 2017 LEDE project
#
# This is free software, licensed under the GNU General Public License v2.
# See /LICENSE for more information.
@@ -8,8 +9,8 @@
include $(INCLUDE_DIR)/kernel.mk
PKG_NAME:=brcm2708-gpu-fw
-PKG_VERSION:=2016-06-08
-PKG_RELEASE:=70143fe9d371cd6486a80d6765e93b5574212b64
+PKG_VERSION:=2017-03-03
+PKG_RELEASE:=78c4983379de0537f49a97fb37ceaaf42632b28c
PKG_BUILD_DIR:=$(KERNEL_BUILD_DIR)/$(PKG_NAME)/rpi-firmware-$(PKG_RELEASE)
@@ -24,7 +25,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-LICENCE.broadcom
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=LICENCE.broadcom
- MD5SUM:=4a4d169737c0786fb9482bb6d30401d1
+ HASH:=ba76edfc10a248166d965b8eaf320771c44f4f432d4fce2fd31fd272e7038add
endef
$(eval $(call Download,LICENCE_broadcom))
@@ -32,7 +33,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-bootcode.bin
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=bootcode.bin
- MD5SUM:=5bbb5f25dfe16f2871d5defcc48ac9ff
+ HASH:=d990031baec20fe2cd5e24d9f3d6fc34891afdb128838d010d9a0249ae29ea6b
endef
$(eval $(call Download,bootcode_bin))
@@ -40,7 +41,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-fixup.dat
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=fixup.dat
- MD5SUM:=c85a8a7fd6f1012dedb979d5a5350135
+ HASH:=38b69384f62bc7b64f17dcedc03c5582af6b4f8dfc25fe5904d4eb3181a3387b
endef
$(eval $(call Download,fixup_dat))
@@ -48,7 +49,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-fixup_cd.dat
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=fixup_cd.dat
- MD5SUM:=1e6c0d6c576956282b498f255eb12d3b
+ HASH:=05c682ffcc74cd1356f1b9a32a7034763bfea94e5cb54eaaa2e69affc1cd33d7
endef
$(eval $(call Download,fixup_cd_dat))
@@ -56,7 +57,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-start.elf
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=start.elf
- MD5SUM:=94f8e421d6e46e89a60aa001af63844e
+ HASH:=59b9d26b463a84f017fae186493bb54e642de6c7e0376b3cbe3375df6132edc0
endef
$(eval $(call Download,start_elf))
@@ -64,7 +65,7 @@
FILE:=$(RPI_FIRMWARE_FILE)-start_cd.elf
URL:=$(RPI_FIRMWARE_URL)
URL_FILE:=start_cd.elf
- MD5SUM:=0a9082c25af181cbf16338de2362d5d6
+ HASH:=fb9aea03eb6790062c100166444bf7d2b8a6cea605bd041f905fcacefacbbae2
endef
$(eval $(call Download,start_cd_elf))
--- a/package/base-files/files/etc/rc.local
+++ b/package/base-files/files/etc/rc.local
@@ -1,4 +1,13 @@
# Put your custom commands here that should be executed once
# the system init finished. By default this file does nothing.
+model=`cat /proc/device-tree/model`
+case "$model" in
+"Raspberry Pi Zero W Rev"* |\
+"Raspberry Pi 3 Model B Rev"*)
+ /usr/bin/hciattach /dev/ttyAMA0 bcm43xx 3000000 flow -
+ ;;
+esac
+/usr/bin/hciconfig hci0 up
+
exit 0