I'am doing exaclty as DGDodo described with his r45269 files and getting exactly the same outputs, but after running kernel i run into problems.
P-2812HNU-Fx # bootm 0x80800000
## Booting kernel from Legacy Image at 80800000 ...
Image Name: MIPS OpenWrt Linux-3.18.10
Created: 2015-04-04 23:46:13 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 4718520 Bytes = 4.5 MiB
Load Address: 80002000
Entry Point: 80002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.18.10 (sylwek@WRT) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44945) ) #2 Sun Apr 5 01:45:49 CEST 2015
[ 0.000000] SoC: VR9 rev 1.1
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc)
[ 0.000000] MIPS: machine is P2812HNUF1 - ZyXEL P-2812HNU-F1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00014b20
[ 0.000000] Readback ErrCtl register=00014b20
[ 0.000000] Memory: 121772K/131072K available (3506K kernel code, 149K rwdata, 1036K rodata, 3160K init, 206K bss, 9300K reserved)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 500MHz
[ 0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[ 0.032000] pid_max: default: 32768 minimum: 301
[ 0.036000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.044000] pinctrl core: initialized pinctrl subsystem
[ 0.052000] NET: Registered protocol family 16
[ 0.060000] pinctrl-xway 1e100b10.pinmux: Init done
[ 0.064000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[ 0.168000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[ 0.172000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[ 0.176000] MEM 0x0000000018000000..0x0000000019ffffff
[ 0.180000] IO 0x000000001ae00000..0x000000001affffff
[ 0.192000] gpio-stp-xway 1e100bb0.stp: Init done
[ 0.196000] usbcore: registered new interface driver usbfs
[ 0.200000] usbcore: registered new interface driver hub
[ 0.204000] usbcore: registered new device driver usb
[ 0.208000] PCI host bridge to bus 0000:00
[ 0.212000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[ 0.216000] pci_bus 0000:00: root bus resource [io 0xffffffff]
[ 0.220000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.224000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.228000] Switched to clocksource MIPS
[ 0.232000] NET: Registered protocol family 2
[ 0.236000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.244000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.252000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.256000] TCP: reno registered
[ 0.260000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.268000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.272000] NET: Registered protocol family 1
[ 5.136000] gptu: totally 6 16-bit timers/counters
[ 5.140000] gptu: misc_register on minor 63
[ 5.144000] gptu: succeeded to request irq 126
[ 5.152000] gptu: succeeded to request irq 127
[ 5.156000] gptu: succeeded to request irq 128
[ 5.160000] gptu: succeeded to request irq 129
[ 5.164000] gptu: succeeded to request irq 130
[ 5.168000] gptu: succeeded to request irq 131
[ 5.172000] ralink,eeprom ralink_eep: using RT3062.eeprom as eeprom
[ 5.180000] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a1x.bin
[ 5.188000] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 6A60000
[ 5.192000] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 6A60000
[ 5.300000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 5.308000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 5.312000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 5.324000] msgmni has been set to 237
[ 5.328000] io scheduler noop registered
[ 5.332000] io scheduler deadline registered (default)
[ 5.340000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[ 5.348000] console [ttyLTQ0] enabled
[ 5.348000] console [ttyLTQ0] enabled
[ 5.356000] bootconsole [early0] disabled
[ 5.356000] bootconsole [early0] disabled
[ 5.364000] nand: device found, Manufacturer ID: 0xec, Chip ID: 0xf1
[ 5.364000] nand: Samsung NAND 128MiB 3,3V 8-bit
[ 5.364000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[ 5.380000] Scanning device for bad blocks
[ 5.424000] Bad eraseblock 755 at 0x000005e60000
[ 5.444000] 4 ofpart partitions found on MTD device 10000000.nand-parts
[ 5.448000] Creating 4 MTD partitions on "10000000.nand-parts":
[ 5.452000] 0x000000000000-0x000000040000 : "uboot"
[ 5.460000] 0x000000040000-0x000000060000 : "uboot-env"
[ 5.464000] 0x000000060000-0x000000260000 : "kernel"
[ 5.468000] 0x000000260000-0x000008000000 : "ubi"
[ 5.576000] libphy: lantiq,xrx200-mdio: probed
[ 5.600000] net-xrx200: invalid MAC, using random
[ 5.668000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1)
[ 5.736000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1)
[ 5.804000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[ 5.872000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[ 5.940000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1)
[ 5.948000] wdt 1f8803f0.watchdog: Init done
[ 5.952000] TCP: cubic registered
[ 5.956000] NET: Registered protocol family 17
[ 5.960000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 5.972000] Bridge firewalling registered
[ 5.976000] 8021q: 802.1Q VLAN Support v1.8
[ 5.984000] UBI error: ubi_auto_attach: no valid UBI magic found i[ 5.996000] Freeing unused kernel memory: 3160K (8049a000 - 807b0000)
[ 6.020000] init: failed to symlink /tmp -> /var
[ 6.020000] init: Console is alive
[ 6.028000] init: - watchdog -
[ 6.056000] dwc2 1e101000.ifxhcd: requested GPIO 489
[ 6.916000] dwc2 1e101000.ifxhcd: DWC OTG Controller
[ 6.916000] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[ 6.924000] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[ 6.932000] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[ 6.932000] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[ 6.944000] hub 1-0:1.0: USB hub found
[ 6.948000] hub 1-0:1.0: 1 port detected
[ 7.812000] dwc2 1e106000.ifxhcd: DWC OTG Controller
[ 7.812000] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[ 7.820000] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[ 7.828000] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[ 7.828000] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[ 7.840000] hub 2-0:1.0: USB hub found
[ 7.844000] hub 2-0:1.0: 1 port detected
[ 8.028000] init: - preinit -
[ 8.140000] random: procd urandom read with 31 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 11.248000] procd: - early -
[ 11.252000] procd: - watchdog -
[ 11.816000] procd: - ubus -
[ 12.828000] procd: - init -
Please press Enter to activate this console.
[ 13.856000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
[ 13.884000] NET: Registered protocol family 10
[ 13.892000] NET: Registered protocol family 8
[ 13.892000] NET: Registered protocol family 20
[ 13.904000] PPP generic driver version 2.4.2
[ 13.916000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.936000] MEI CPE Driver, Version 1.2.0
[ 13.936000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
Lantiq CPE API Driver version: DSL CPE API V4.11.4
[ 13.960000]
[ 13.960000] Predefined debug level: 2
[ 13.972000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 13.976000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 13.988000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.000000] Infineon Technologies DEU driver version 2.0.0
[ 14.004000] IFX DEU DES initialized (multiblock).
[ 14.008000] IFX DEU AES initialized (multiblock).
[ 14.012000] IFX DEU ARC4 initialized (multiblock).
[ 14.020000] IFX DEU SHA1 initialized.
[ 14.020000] IFX DEU MD5 initialized.
[ 14.024000] IFX DEU SHA1_HMAC initialized.
[ 14.028000] IFX DEU MD5_HMAC initialized.
[ 14.040000] nf_conntrack version 0.5.0 (1952 buckets, 7808 max)
[ 14.068000] NET: Registered protocol family 24
[ 14.092000] xt_time: kernel timezone is -0000
[ 14.112000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.136000] cfg80211: World regulatory domain updated:
[ 14.136000] cfg80211: DFS Master region: unset
[ 14.144000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 14.152000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.160000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.168000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.176000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.184000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 14.192000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 14.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.208000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 14.304000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 14.308000] rt2800pci 0000:00:0e.0: failed to load eeprom property
[ 14.312000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT3062.eeprom'.
After that it just reboots. Any solution to that?