The content of this topic has been archived on 4 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Hi all,
Has anyone tried adding support for the Netgear PR2000? Seems like a good cheap portable router. 2x2:2 MIMO config, USB, WAN and LAN port.
There is some info here: https://wikidevi.com/wiki/Netgear_PR2000
If no one else has I plan to give it a go. Seems like most of the hardware is already supported on other routers but still need to identify the Flash chip so will need to open it up.
(Last edited by ddfczm on 7 Aug 2014, 21:06)
Opened it up and had a closer look.
CPU/Wifi/Eth: MediaTek MT7620N SOC
RAM: 64 MiB (EtronTech EM68B16CWQD-25H)
Flash: MX25L12845EMI-106
I can't find too much information about the Flash memory chip & how big it is. I assume this is the data sheet for the family of chip: http://www.macronix.com/Lists/DataSheet … 20v1.9.pdf
Here is the mtd info from dmesg. Looks like its 16MB
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
Creating 19 MTD partitions on "raspi":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000240000 : "Kernel"
0x000000ea0000-0x000000ec0000 : "English UI"
0x000000ec0000-0x000000ee0000 : "Chinese UI"
0x000000ee0000-0x000000f00000 : "Russian UI"
0x000000f00000-0x000000f20000 : "Portuguese UI"
0x000000f20000-0x000000f40000 : "German UI"
0x000000f40000-0x000000f60000 : "Other UI"
0x000000f60000-0x000000f70000 : "WiFi Data"
0x000000f70000-0x000000f80000 : "SC Private Data"
0x000000f80000-0x000000f90000 : "POT"
0x000000f90000-0x000000fa0000 : "Traffic Meter"
0x000000fa0000-0x000000fb0000 : "Traffic Meter2"
0x000000fb0000-0x000000fc0000 : "SC Nvram"
0x000000fc0000-0x000000fd0000 : "DPF"
0x000000240000-0x000000ea0000 : "Rootfs"
0x000000fd0000-0x000000fe0000 : "Ralink Nvram"
0x000000fe0000-0x000000ff0000 : "Reserved Block1"
0x000000ff0000-0x000001000000 : "Reserved Block2"
I visit this URL:
routerlogin.net/setup.cgi?todo=debug
when i connect to PR2000 to enable debug mode, which the telnet can be turned on.
then telnet routerlogin.net
"cat /proc/mtd" show such result:
dev: size erasesize name
mtd0: 00040000 00010000 "Bootloader"
mtd1: 00200000 00010000 "Kernel"
mtd2: 00020000 00010000 "English UI"
mtd3: 00020000 00010000 "Chinese UI"
mtd4: 00020000 00010000 "Russian UI"
mtd5: 00020000 00010000 "Portuguese UI"
mtd6: 00020000 00010000 "German UI"
mtd7: 00020000 00010000 "Other UI"
mtd8: 00010000 00010000 "WiFi Data"
mtd9: 00010000 00010000 "SC Private Data"
mtd10: 00010000 00010000 "POT"
mtd11: 00010000 00010000 "Traffic Meter"
mtd12: 00010000 00010000 "Traffic Meter2"
mtd13: 00010000 00010000 "SC Nvram"
mtd14: 00010000 00010000 "DPF"
mtd15: 00c60000 00010000 "Rootfs"
mtd16: 00010000 00010000 "Ralink Nvram"
mtd17: 00010000 00010000 "Reserved Block1"
mtd18: 00010000 00010000 "Reserved Block2"
which means the flash is 16M.
and "cat /proc/cpuinfo" shows:
# cat /proc/cpuinfo
system type : Ralink SoC
processor : 0
cpu model : MIPS 24Kc V5.0
BogoMIPS : 386.04
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ff8, 0x0ff8, 0x0213, 0x0ff8]
ASEs implemented : mips16 dsp
shadow register sets : 1
core : 0
VCED exceptions : not available
VCEI exceptions : not available
Also the netgear PR2000 firmware open source code can be download at:
http://kb.netgear.com/app/answers/detai … mers-(gpl)
PR2000 really a good net gear. There's only one reason i want to update firmware is want to install shadowsock on it.
If someone know other solution that the shadowsock can be installed except change the whole system. please tell me. thanks,
I am looking to buy some of these routers to my work place, since they are very portable but I really want openwrt on them before so we can both use usb modems and maybe increase the output voltage on the antennas.
Any one working on it?
Hey there!
I'd just like to know if someone did test to install OpenWRT on the PR2000 yet?
Since jiwei posted the SourceCode in the End of 2014 perhaps someone did some more testing?
What I found when I searched the web for the MediaTek SOC you already mentioned here is this:
https://wikidevi.com/wiki/WRTnode_(MT7620N)
https://downloads.openwrt.org/snapshots … ages/luci/
https://dev.openwrt.org/ticket/18849
Perhaps anyone is able to do some further testing with this?
...would love to see OpenWRT on the PR2000 because of it's VPN-Ability 
Thx & best Regards,
SchwarzerRiese
I am interested in this device now.
I use the TP-Link TL-WR710N extensively:
https://forum.openwrt.org/viewtopic.php?pid=238822
Previously the pricing on the PR2000 was out of whack, but now it looks like it's priced appropriately in the US market.
This Netgear PR2000 is very similar in that it has a built-in power plug, a USB port, and two 100BASE-T ports.
Internally, the PR2000 has twice the RAM and flash storage as the TL-WR710N. That's a big plus. The PR2000 also has a switch and some additional LEDs. It also looks like it can take power in from USB, though that's not interesting to me. CPU is slightly faster on the Mhz, but that's a poor comparison.
On the downside, the swivel antenna looks gimmicky and I'd be worried about that getting broken off out in the field. Also, the MediaTek chip is an issue due to their exceptionally bad Linux/Android reputation. Netgear's reputation isn't very good either.
I will probably buy one and give it a try.
Hello,
Thank you for your interest in this device, I'd really like to be able to test OpenWRT on this powerful little device.
Let us know if you decide to investigate a bit more.
I just bought this device too, tell me if you need a volunteer 
I am interested in this device now.
I use the TP-Link TL-WR710N extensively:
https://forum.openwrt.org/viewtopic.php?pid=238822Previously the pricing on the PR2000 was out of whack, but now it looks like it's priced appropriately in the US market.
This Netgear PR2000 is very similar in that it has a built-in power plug, a USB port, and two 100BASE-T ports.
Internally, the PR2000 has twice the RAM and flash storage as the TL-WR710N. That's a big plus. The PR2000 also has a switch and some additional LEDs. It also looks like it can take power in from USB, though that's not interesting to me. CPU is slightly faster on the Mhz, but that's a poor comparison.
On the downside, the swivel antenna looks gimmicky and I'd be worried about that getting broken off out in the field. Also, the MediaTek chip is an issue due to their exceptionally bad Linux/Android reputation. Netgear's reputation isn't very good either.
I will probably buy one and give it a try.
I also have several NETGEAR N300 PR2000 Trek (http://youtu.be/Fyo7l8J5Q7I | https://www.youtube.com/watch?v=lA4vwYXqLZ0) and offer this to the OpenWRT firmware for testing.
Travel Router, Range Extender, Access Point and Wireless Bridge function quite well but unfortunately the original software is very Basic. The device is small, uses very little power, and thanks to USB completely independent of mains supplies with a power bank.
It works so well to share Internetverbidungen that require authentication page to enter credentials, z. B. Hotspots Telekom, etc in hotels ..
It is the only Travel Router, which can be very easily retrofitted with external antenna connections even.
With the Netgear OpenWrt PR2000 would then really perfect!
Very, very thanks, if you could provide for the great part OpenWrt firmware!
Pauline
***************************************************
Ich habe auch mehrere NETGEAR N300 PR2000 Trek (https://www.youtube.com/watch?v=Y4AjrSyuFSY) und biete diese zum Testen der OpenWRT-Firmware an. .
Travel Router, Range Extender, Access Point and Wireless Bridge funktionieren schon ganz gut aber leider ist die Original Software nur sehr Basic. Das Gerät ist klein, verbraucht sehr wenig Strom und ist dank USB mit einer Power Bank vollkommen unabhängig von Stromnetz.
Es klappt damit auch Internetverbidungen zu teilen, die eine Authentifikationsseite zur Eingabe von Zugangsdaten erfordern, z. B. Hotspots der Telekom, in Hotels usw..
Es ist der einzige Travel-Router, der sich sogar sehr einfach mit externen Antennenanschlüssen nachrüsten lässt.
Mit OpenWrtt wären die Netgear PR2000 dann wirklich perfekt!
Ganz, ganz lieben Dank, wenn ihr für das tolle Teil OpenWrt-Firmware bereitstellen könntet!
Pauline
Agree, the router is really nice, however it lacks OpenWRT. Wish to see it on the supported list!
Maybe someone could check what processor it actually is?
Hi, this is my first time posting here and I'm relatively new to OpenWRT, so please forgive the noobness.
I have a PR2000, Ver 1.3 with firmware V1.0.0.14. I would like to get OpenWRT running on it.
I can enable debug mode with routerlogin.net/setup.cgi?todo=debug, but admin/password doesn't get me into telnet. I've tried other username/passwords like Netguy/Netdog, etc. but nothing works.
I figured out how to get a serial connection, here is what I have learned:
TP9=Tx
TP8=Vcc
TP7=Rx
TP10=G
Baud=57600
Here is what I got during boot:
####################################
U-Boot 1.1.3 (Apr 24 2014 - 13:37:12)
Board: Ralink APSoC DRAM: 64 MB
enable ephy clock...done. rf reg 29 = 5
SSC disabled.
spi_wait_nsec: 29
spi device id: c2 20 18 c2 20 (2018c220)
find flash: MX25L12805D
*** Warning - bad CRC, using default environment
============================================
Ralink UBoot Version: 4.1.1.0
--------------------------------------------
ASIC 7620_MP (Port5<->None)
DRAM component: 512 Mbits DDR, width 16
DRAM bus: 16 bit
Total memory: 64 MBytes
Flash component: SPI Flash
Date:Apr 24 2014 Time:13:37:12
============================================
icache: sets:512, ways:4, linesz:32 ,total:65536
dcache: sets:256, ways:4, linesz:32 ,total:32768
Press Ctrl+C to Enter the Main loop...
1 0
******************************************
Uboot StandAlone Entry
******************************************
Enter NMRP_main
Flash Sector Number : 256.
Waitting for RX_DMA_BUSY status Start... done
ETH_STATE_ACTIVE!!
NMRP_FLASH_SIZE_buffer --> a1000000.
NMRP:LISTENING
### No NMRP Server found ###
******************************************
Uboot StandAlone Entry
******************************************
Flash Sector Number : 256.
***************************************************
Sercomm Boot Version 3.12.0
***************************************************
Entering Firmware : Everything is OK.
3: System Boot system code via Flash.
## Booting image at bc040000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1537321 Bytes = 1.5 MB
Load Address: 80000000
Entry Point: 8000c310
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.36 (root@localhost.localdomain) (gcc version 3.4.2) #219 Thu Feb 12 15:47:55 CST 2015
The CPU feqenuce set to 580 MHz
MIPS CPU sleep mode enabled.
PCIE: bypass PCIe DLL.
PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
disable all power about PCIe
PCIE: PLL power down for MT7620N
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock15 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00051140
Readback ErrCtl register=00051140
Memory: 60344k/65536k available (3276k kernel code, 5192k reserved, 946k data, 168k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:80405ee8, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
RALINK_GPIOMODE = 1a311d
RALINK_GPIOMODE = 18311d
PPLL_CFG1=0x4010000
MT7620 PPLL unlock
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Load Kernel WDG Timer Module
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
fuse init (API version 7.15)
msgmni has been set to 117
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Ralink gpio driver initialized
spidrv_major = 217
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : c2 20 18 c2 20 (2018c220)
MX25L12805D(c2 2018c220) (16384 Kbytes)
mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536
Creating 19 MTD partitions on "raspi":
0x000000000000-0x000000040000 : "Bootloader"
0x000000040000-0x000000240000 : "Kernel"
0x000000ea0000-0x000000ec0000 : "English UI"
0x000000ec0000-0x000000ee0000 : "Chinese UI"
0x000000ee0000-0x000000f00000 : "Russian UI"
0x000000f00000-0x000000f20000 : "Portuguese UI"
0x000000f20000-0x000000f40000 : "German UI"
0x000000f40000-0x000000f60000 : "Other UI"
0x000000f60000-0x000000f70000 : "WiFi Data"
0x000000f70000-0x000000f80000 : "SC Private Data"
0x000000f80000-0x000000f90000 : "POT"
0x000000f90000-0x000000fa0000 : "Traffic Meter"
0x000000fa0000-0x000000fb0000 : "Traffic Meter2"
0x000000fb0000-0x000000fc0000 : "SC Nvram"
0x000000fc0000-0x000000fd0000 : "DPF"
0x000000240000-0x000000ea0000 : "Rootfs"
0x000000fd0000-0x000000fe0000 : "Ralink Nvram"
0x000000fe0000-0x000000ff0000 : "Reserved Block1"
0x000000ff0000-0x000001000000 : "Reserved Block2"
rdm_major = 253
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
usbcore: registered new interface driver net1080
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (942 buckets, 3768 max)
nf_conntrack_rtsp v0.6.21 loading
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
GRE over IPv4 demultiplexor driver
gre: can't add protocol
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
TCP cubic registered
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
L2TP IP encapsulation support (L2TPv3)
L2TP netlink interface
L2TP ethernet pseudowire support (L2TPv3)
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:15.
Freeing unused kernel memory: 168k freed
init started: BusyBox v1.12.1 (2015-02-12 14:19:44 CST)
starting pid 45, tty '': '/usr/etc/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=Systeswitch register base addr to 0xb0000000
m Architecture Depar0x18111d
tment=
write offset 0x60, value 0x18311d
led_pb_api: module license 'Sercomm' taints kernel.
Disabling lock debugging due to kernel taint
Register LED ID <20>
Register LED ID <60>
Register LED ID <10>
Register LED ID <90>
Register LED ID <94>
Register LED ID <95>
netfilter dnshj choose interested dns queries module loaded !
init common module successful
insert firewall block module success
fake source dos protect modules is inserted
netfilter PSD and TCP/UDP Echo/Chargen Attack loaded
netfilter tcp syn flood module loaded
netfilter clamp total session for one src ip module loaded
netfilter other dos module loaded
insmod finish
Raeth v3.0 (Tasklet,SkbRecycle)
phy_tx_ring = 0x03696000, tx_ring = 0xa3696000
phy_rx_ring0 = 0x03697000, rx_ring0 = 0xa3697000
SMACCR1 -- : 0x0000000c
SMACCR0 -- : 0x43762077
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
device eth2.1 entered promiscuous mode
device eth2 entered promiscuous mode
preapre_sys_for_3g
mknod: /dev/zero: File exists
mknod: /dev/ttyUSB0: File exists
mknod: /dev/ttyUSB1: File exists
mknod: /dev/ttyUSB2: File exists
mknod: /dev/ttyUSB3: File exists
mkdir: cannot create directory '/var': File exists
preapre_sys_for_3g done
[rc debug]/usr/sbin/rc init
[SYSTEM]echo "Configure 6855 ESW port base vlan"
Configure 6855 ESW port base vlan
[SYSTEM]switch reg w 2004 ff0003
switch reg write offset=2004, value=ff0003
[SYSTEM]switch reg w 2104 ff0003
switch reg write offset=2104, value=ff0003
[SYSTEM]switch reg w 2204 ff0003
switch reg write offset=2204, value=ff0003
[SYSTEM]switch reg w 2304 ff0003
switch reg write offset=2304, value=ff0003
[SYSTEM]switch reg w 2404 ff0003
switch reg write offset=2404, value=ff0003
[SYSTEM]switch reg w 2504 ff0003
switch reg write offset=2504, value=ff0003
[SYSTEM]switch reg w 2010 810000c0
switch reg write offset=2010, value=810000c0
[SYSTEM]switch reg w 2110 810000c0
switch reg write offset=2110, value=810000c0
[SYSTEM]switch reg w 2210 810000c0
switch reg write offset=2210, value=810000c0
[SYSTEM]switch reg w 2310 810000c0
switch reg write offset=2310, value=810000c0
[SYSTEM]switch reg w 2410 810000c0
switch reg write offset=2410, value=810000c0
[SYSTEM]switch reg w 2510 810000c0
switch reg write offset=2510, value=810000c0
[SYSTEM]switch reg w 2610 81000000
switch reg write offset=2610, value=81000000
[SYSTEM]switch reg w 2710 81000000
switch reg write offset=2710, value=81000000
[SYSTEM]switch reg w 2604 20ff0003
switch reg write offset=2604, value=20ff0003
[SYSTEM]switch reg w 2704 20ff0003
switch reg write offset=2704, value=20ff0003
[SYSTEM]switch reg w 2610 81000000
switch reg write offset=2610, value=81000000
[SYSTEM]switch reg w 2014 10002
switch reg write offset=2014, value=10002
[SYSTEM]switch reg w 2114 10001
switch reg write offset=2114, value=10001
[SYSTEM]switch reg w 2214 10001
switch reg write offset=2214, value=10001
[SYSTEM]switch reg w 2314 10001
switch reg write offset=2314, value=10001
[SYSTEM]switch reg w 2414 10001
switch reg write offset=2414, value=10001
[SYSTEM]switch reg w 2514 100br0: port 1(eth2.1) entering learning state
01br0: port 1(eth2.1) entering learning state
switch reg write offset=2514, value=10001
[SYSTEM]switch vlan set device eth2 left promiscuous mode
0 1br0: port 1(eth2.1) entering learning state
01111111
[SYSTEM]switch vlan set 1 2 10000011
[SYSTEM]switch clear
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
[SYSTEMdevice eth2 entered promiscuous mode
]/sbr0: port 1(eth2.1) entering learning state
bibr0: port 1(eth2.1) entering learning state
n/ifconfig br0 down hw ether 6C:B0:CE:71:72:D8 up
[SYSTswitch register base addr to 0xb0117014
EM]/sbin/ifconfig eth2.1 down
[SYSTEM]/sbwrite offset 0x0, value 0xee0000c
in/ifconfig eth2.1 hw ether 6C:B0:CE:71:72:D8
[SYSTEM]/sbin/ifconfig eth2.1 up
[SYSTEM]reg s 0xb0117014
[SYSTEM]reg w 0 0xee0000c
[rc.c::sync_system_mode():417] sync device mode
[rc.c::sync_system_mode():444] device in wired mode
RC: wifi_init()
rules = <>, timeout = 20
[SYSTEM]insmod /lib/modules/2.6.36/kernel/drivers/net/wireless/rt2860v2_ap/rt2860v2_ap.ko mac=6C:B0:CE:71:72:D8
=== pAd = c07b6000, size = 968608 ===
<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6_edcca_monitor_20131222
[rc.c::rc_init():731] force ap mode to disable
[rc.c::rc_init():770] find_new_version: 0
[rc.c::sync_system_mode():417] sync device mode
[rc.c::sync_system_mode():444] device in wired mode
[rc debug]/usr/sbin/rc wlan restart
ap_name=wlan action=restart
[rc.c::rc_action():995] rc_action before add wlan - restart
rc action <wlan @ restart> before file_lock.
rc action <wlan @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add wlan - restart
[rc.c::rc_stop():937] Calling Stop function of wlan
[SYSTEM]/usr/bin/killall apcli_monitor
killall: apcli_monitor: no process killed
[SYSTEM]/usr/bin/killall rt2860apd
killall: rt2860apd: no process killed
[SYSTEM]/usr/bin/killall rtinicapd
killall: rtinicapd: no process killed
[SYSTEM]/sbin/ifconfig wds0 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds0
interface wds0 does not exist!
[SYSTEM]/sbin/ifconfig wdsi0 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi0
interface wdsi0 does not exist!
[SYSTEM]/sbin/ifconfig wds1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds1
interface wds1 does not exist!
[SYSTEM]/sbin/ifconfig wdsi1 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi1
interface wdsi1 does not exist!
[SYSTEM]/sbin/ifconfig wds2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds2
interface wds2 does not exist!
[SYSTEM]/sbin/ifconfig wdsi2 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wdsi2
interface wdsi2 does not exist!
[SYSTEM]/sbin/ifconfig wds3 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/brctl delif br0 wds3
interface wds3 does not exist!
[SYSCan't find DB for id==40
TEM]/sbin/ifconfig wdsi3 down
ifconfig: SIOCGIFFLAGS: No suchCan't find DB for id==41
device
[SYSTEM]/sbin/brctl delif br0 wdsi3
interface wCan't find DB for id==42
dsi3 does not exist!
[SYSTEM]/sbin/ifconfig apcli0 down
Can't find DB for id==45
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/sbin/ifconfig ra0 down
[SYSTEM]/sbin/iwpriv rai0 set RadioOn=1
rai0 no private ioctls.
[SYSTEM]/sbin/ifconfig rai0 down
ifconfig: SIOCGIFFLAGS: No such device
[SYSTEM]/bin/led_app off 40
[SYSTEM]/bin/led_app off 41
[SYSTEM]/bin/led_app off 42
[SYSTEM]/bin/led_app off 45
[SYSTEM]/usr/bin/killall -9 nas
killall: nas: no process killed
[SYSTEM]/usr/bin/killall -9 eapd
killall: eapd: no process killed
[SYSTEM]/usr/bin/killall -9 wps_monitor
killall: wps_monitor: no process killed
Can't find DB for id==45
an't find DB for id==61
2mCan't find DB for id==62
[SCan't find DB for id==63
YSTCan't find DB for id==64
EMCan't find DB for id==65
]/Can't find DB for id==66
usCan't find DB for id==67
r/bCan't find DB for id==68
in/killall -9 wps_ap
killall: wps_ap: no process killed
[SYSTEM]/usr/bin/killall -9 wps_det
killall: wps_det: no process killed
[SYSTEM]/bin/echo 0 > /proc/sc_led/wifi_mode
[SYSTEM]/bin/echo 0 > /proc/sc_led/wps_running
[SYSTEM]/usr/bin/rm -rf /tmp/wps_monitor.pid
[SYSTEM]/usr/bin/rm -rf /tmp/bcmupnp.pid
[SYSTEM]/usr/bin/killall -9 wps_det
killall: wps_det: no processdevice ra0 entered promiscuous mode
kdevice ra0 left promiscuous mode
illdevice ra0 entered promiscuous mode
eddevice ra0 left promiscuous mode
[rc.c::rc_start():899] Calling Start function of wlan
[SYSTEM]brctl addif br0 ra0
can't add ra0 to bridge br0: Invalid argument
[SYSTEM]brctl addif br0 rai0
interface rai0 does not exist!
[SYSTEM]/usr/sbin/wsc_daemon &
sh: /usr/sbin/wsc_daemon: not found
[SYSTEM]mkdir -p /etc/Wireless/RT2860
[wifi_mtk/wifi.c::create_ralink_driver_conf():829] NOT apcli mode, follow spec to show extchannel
[SYSTEM]mkdir -p /etc/Wireless/iNIC
[wifi_mtk/wifi.c::create_ralink_driver_conf():829] NOT apcli mode, follow spec to show extchannel
Interface doesn't accept private ioctl...
e2p (8BE7): Network is down
[wifi_mtk/wifi.c::pr2000_wifidata_modify():1323]
[wifi_mtkRX DESC a37a0000 size = 2048
/wifi.c::prepare_single_sRTMP_TimerListAdd: add timer obj c0863320!
kuRTMP_TimerListAdd: add timer obj c081c238!
()RTMP_TimerListAdd: add timer obj c081ee54!
:1RTMP_TimerListAdd: add timer obj c081ef14!
22RTMP_TimerListAdd: add timer obj c081efd4!
6]RTMP_TimerListAdd: add timer obj c081f094!
cRTMP_TimerListAdd: add timer obj c081f154!
urRTMP_TimerListAdd: add timer obj c081f214!
reRTMP_TimerListAdd: add timer obj c081f2d4!
ntRTMP_TimerListAdd: add timer obj c081f394!
wRTMP_TimerListAdd: add timer obj c081f454!
ifRTMP_TimerListAdd: add timer obj c081f514!
i RTMP_TimerListAdd: add timer obj c081f5d4!
reRTMP_TimerListAdd: add timer obj c081f694!
giRTMP_TimerListAdd: add timer obj c081f754!
onRTMP_TimerListAdd: add timer obj c081f814!
iRTMP_TimerListAdd: add timer obj c081f8d4!
s RTMP_TimerListAdd: add timer obj c081f994!
NoRTMP_TimerListAdd: add timer obj c081c20c!
rtRTMP_TimerListAdd: add timer obj c081ee28!
h RTMP_TimerListAdd: add timer obj c081eee8!
AmRTMP_TimerListAdd: add timer obj c081efa8!
erRTMP_TimerListAdd: add timer obj c081f068!
icRTMP_TimerListAdd: add timer obj c081f128!
aRTMP_TimerListAdd: add timer obj c081f1e8!
[RTMP_TimerListAdd: add timer obj c081f2a8!
wiRTMP_TimerListAdd: add timer obj c081f368!
fiRTMP_TimerListAdd: add timer obj c081f428!
_mRTMP_TimerListAdd: add timer obj c081f4e8!
tkRTMP_TimerListAdd: add timer obj c081f5a8!
/wRTMP_TimerListAdd: add timer obj c081f668!
ifRTMP_TimerListAdd: add timer obj c081f728!
i.RTMP_TimerListAdd: add timer obj c081f7e8!
c:RTMP_TimerListAdd: add timer obj c081f8a8!
:pRTMP_TimerListAdd: add timer obj c081f968!
reRTMP_TimerListAdd: add timer obj c081c1e0!
paRTMP_TimerListAdd: add timer obj c081ee80!
reRTMP_TimerListAdd: add timer obj c081ef40!
_sRTMP_TimerListAdd: add timer obj c081f000!
inRTMP_TimerListAdd: add timer obj c081f0c0!
glRTMP_TimerListAdd: add timer obj c081f180!
e_RTMP_TimerListAdd: add timer obj c081f240!
skRTMP_TimerListAdd: add timer obj c081f300!
u(RTMP_TimerListAdd: add timer obj c081f3c0!
):RTMP_TimerListAdd: add timer obj c081f480!
12RTMP_TimerListAdd: add timer obj c081f540!
32RTMP_TimerListAdd: add timer obj c081f600!
] RTMP_TimerListAdd: add timer obj c081f6c0!
==RTMP_TimerListAdd: add timer obj c081f780!
==RTMP_TimerListAdd: add timer obj c081f840!
==RTMP_TimerListAdd: add timer obj c081f900!
wiRTMP_TimerListAdd: add timer obj c081f9c0!
fiRTMP_TimerListAdd: add timer obj c07bf578!
rRTMP_TimerListAdd: add timer obj c07bedc0!
egRTMP_TimerListAdd: add timer obj c07bf548!
ioRTMP_TimerListAdd: add timer obj c07bf8f0!
n RTMP_TimerListAdd: add timer obj c07bf640!
isRTMP_TimerListAdd: add timer obj c07bf670!
NRTMP_TimerListAdd: add timer obj c07bf830!
orRTMP_TimerListAdd: add timer obj c07bf860!
thRTMP_TimerListAdd: add timer obj c07c2b80!
ARTMP_TimerListAdd: add timer obj c07c23c8!
meRTMP_TimerListAdd: add timer obj c07c2b50!
riRTMP_TimerListAdd: add timer obj c07c2ef8!
caRTMP_TimerListAdd: add timer obj c07c2c48!
, RTMP_TimerListAdd: add timer obj c07c2c78!
weRTMP_TimerListAdd: add timer obj c07c2e38!
wRTMP_TimerListAdd: add timer obj c07c2e68!
ilRTMP_TimerListAdd: add timer obj c07c6188!
l RTMP_TimerListAdd: add timer obj c07c59d0!
usRTMP_TimerListAdd: add timer obj c07c6158!
e RTMP_TimerListAdd: add timer obj c07c6500!
/eRTMP_TimerListAdd: add timer obj c07c6250!
tcRTMP_TimerListAdd: add timer obj c07c6280!
_rRTMP_TimerListAdd: add timer obj c07c6440!
o/RTMP_TimerListAdd: add timer obj c07c6470!
WiRTMP_TimerListAdd: add timer obj c07c9790!
reRTMP_TimerListAdd: add timer obj c07c8fd8!
leRTMP_TimerListAdd: add timer obj c07c9760!
ssRTMP_TimerListAdd: add timer obj c07c9b08!
/RRTMP_TimerListAdd: add timer obj c07c9858!
T2RTMP_TimerListAdd: add timer obj c07c9888!
86RTMP_TimerListAdd: add timer obj c07c9a48!
0ARTMP_TimerListAdd: add timer obj c07c9a78!
P/RTMP_TimerListAdd: add timer obj c07ccd98!
FCRTMP_TimerListAdd: add timer obj c07cc5e0!
C.RTMP_TimerListAdd: add timer obj c07ccd68!
daRTMP_TimerListAdd: add timer obj c07cd110!
t=RTMP_TimerListAdd: add timer obj c07cce60!
==RTMP_TimerListAdd: add timer obj c07cce90!
==RTMP_TimerListAdd: add timer obj c07cd050!
==RTMP_TimerListAdd: add timer obj c07cd080!
=RTMP_TimerListAdd: add timer obj c07d03a0!
TMP_TimerListAdd: add timer obj c07cfbe8!
[3RTMP_TimerListAdd: add timer obj c07d0370!
2mRTMP_TimerListAdd: add timer obj c07d0718!
[SRTMP_TimerListAdd: add timer obj c07d0468!
YSRTMP_TimerListAdd: add timer obj c07d0498!
TERTMP_TimerListAdd: add timer obj c07d0658!
M]RTMP_TimerListAdd: add timer obj c07d0688!
ecRTMP_TimerListAdd: add timer obj c07d39a8!
hoRTMP_TimerListAdd: add timer obj c07d31f0!
1RTMP_TimerListAdd: add timer obj c07d3978!
>RTMP_TimerListAdd: add timer obj c07d3d20!
/RTMP_TimerListAdd: add timer obj c07d3a70!
tmRTMP_TimerListAdd: add timer obj c07d3aa0!
p/RTMP_TimerListAdd: add timer obj c07d3c60!
apRTMP_TimerListAdd: add timer obj c07d3c90!
clRTMP_TimerListAdd: add timer obj c07d6fb0!
i_RTMP_TimerListAdd: add timer obj c07d67f8!
wiRTMP_TimerListAdd: add timer obj c07d6f80!
fiRTMP_TimerListAdd: add timer obj c07d7328!
_iRTMP_TimerListAdd: add timer obj c07d7078!
f_RTMP_TimerListAdd: add timer obj c07d70a8!
inRTMP_TimerListAdd: add timer obj c07d7268!
itRTMP_TimerListAdd: add timer obj c07d7298!
edRTMP_TimerListAdd: add timer obj c081ea0c!
TMP_TimerListAdd: add timer obj c081e254!
0mRTMP_TimerListAdd: add timer obj c081e9dc!
RTMP_TimerListAdd: add timer obj c081ed84!
TMP_TimerListAdd: add timer obj c081ead4!
32RTMP_TimerListAdd: add timer obj c081eb04!
m[RTMP_TimerListAdd: add timer obj c081ea3c!
SYRTMP_TimerListAdd: add timer obj c081ea6c!
STRTMP_TimerListAdd: add timer obj c081ea9c!
EMRTMP_TimerListAdd: add timer obj c083988c!
]/RTMP_TimerListAdd: add timer obj c08399a8!
sbRTMP_TimerListAdd: add timer obj c08398b8!
inRTMP_TimerListAdd: add timer obj c0820b44!
/ifconfig raRTMP_TimerListAdd: add timer obj c07bc668!
0 RTMP_TimerListAdd: add timer obj c07bfc70!
upRTMP_TimerListAdd: add timer obj c07c3278!
TMP_TimerListAdd: add timer obj c07c6880!
0mRTMP_TimerListAdd: add timer obj c07c9e88!
RTMP_TimerListAdd: add timer obj c07cd490!
RTMP_TimerListAdd: add timer obj c07d0a98!
RTMP_TimerListAdd: add timer obj c07d40a0!
RTMP_TimerListAdd: add timer obj c0820850!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
start ch = 1, ch->num = 1
32 32 32 32
32 32 32 32 30 30 30 30
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26
start ch = 2, ch->num = 2
34 34 34 34
44 44 38 38 34 34 30 30
44 44 38 38 34 34 30 30 44 44 38 38 34 34 30 30
26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26
start ch = 4, ch->num = 5
34 34 34 34
44 44 38 38 34 34 30 30
44 44 38 38 34 34 30 30 44 44 38 38 34 34 30 30
32 32 32 32 32 32 32 32 32 32 32 32 32 32 32 32
start ch = 9, ch->num = 2
34 34 34 34
44 44 38 38 34 34 30 30
44 44 38 38 34 34 30 30 44 44 38 38 34 34 30 30
26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26
start ch = 11, ch->num = 3
40 40 40 40
32 32 32 32 32 32 30 30
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xff1e
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c07bc264!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 1, D2 = 22, CalCode = 49 !!!
RT6352_Temperature_Init : BBPR49 = 0x1
RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff7
Current Temperature from BBP_R49=0xfffffffa
RT6352_TssiTableAdjust: upper_bound = 0x7F decimal: 127
RT6352_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128
*** RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -1 -1 -1 -128 -1 -1
- -1 - -1 -1 -1 -1 -1 -1 -1, offset=-9, tuning=0
RT6352_TssiTableAdjust: G Tssi[-7 .. +7] = -128 -10 -10 -10 -128 -10 -10 - -10 - -10 -10 -10 -10 -10 -10 -10, offset=-9, tuning=0
mp_temperature=0x00, step = +7
E2PROM: G Tssi[-7 .. +7] = -128 -10 -10 -10 -128 -10 -10 - -10 - -10 -10 -10 -10 -10 -10 -10, offset=-9, tuning=0
TX BW Filter Calibration !!!
RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= f, phase=3a)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= 1, phase=3d)
TX IQ Calibration Done!
bAutoTxAgcG = 0
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 01
SYNC - BBP R4 to 20MHz.l
RTMP_TimerListAdd: add timer obj c08210fc!
Main bssid = 6c:b0:ce:71:72:d8
<==== rt28xx_init, Status=0
0x1300 = 00064380
[SYSTEM]/bin/led_app on 40
Can't find DB for id==40
[libscm_wl.c::GenerateUUID():121]
GUI ASCII string: 38833092-3092-1883-82d5-6cb0ce7172d8
[libscm_wl.c::GenerateUUID():122]
GUI HEX string: 388330923092188382d56cb0ce7172d8
[SYSTEM]/usr/bin/killall miniupnpd_wsc
killall: miniupnpd_wsc: no process killed
[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
+ iwpriv ra0 set WscConfMode=0
+ iwpriv rai0 set WscConfMode=0
+ iwpriv ra0 set WscSetupLock=0
+ iwpriv rai0 set WscSetupLock=0
+ route add -host 239.255.255.250 dev br0
+ iwpriv ra0 set WscConfMode=7
+ miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -i eth2.2 -a 192.168.168.1 -n 7777 -u 38833092-3092-1883-82d5-6cb0ce7172d8
Unknown option: -I
Unknown option: ra0
Jan 1 00:00:15 miniupnpd[434]: [truncated] m
Jan 1 00:00:15 miniupnpd[434]: [truncated] m
Jan 1 00:00:Can't find DB for id==45
15 miniupnpd[434]: Failed to open sockets for sending SSDP notify messages. EXITING
[SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptime
[SYSTEM]/usr/sbin/led_app on 45
[SYSTEM]iwpriv rai0 mac 1328=331d0f05
rai0 no private ioctls.
[SYSTEM]/sbin/iwpriv ra0 set DyncVgaEnable=0
[SYSTEM]/usr/bin/killall apcli_monitor
killall: apcli_monitor: no process killed
[wifi_mtk/apcli.c::is_apcli_ok_to_start():42] check if device is ready to start apcli
[wifi_mtk/apcli.c::_dump_apcli_masterap_config():15] ===dump apcli apcli config===
apcli_act_as_wan:1
apcli_remoteap_ssid:
apcli_remoteap_bssid:
apcli_remoteap_auth:
apcli_remoteap_encry:
apcli_remoteap_wpakey:
apcli_remoteap_wep_key:
apcli_remoteap_wep_keyidx:
apcli_remoteap_wep_keytype:
[wifi_mtk/apcli.c::is_apcli_ok_to_start():85] wait pr_wizard
[wifi_mtk/apcli.c::is_apcli_ok_to_start():93] NOT start apcli
unlink running file </var/run/rc.wlan.run>
[rc switch register base addr to 0xb0000000
debug]/usr/sbin/rc hw_nat start
ap_name=hw_n0x18379d
at action=start
[rc.c::rc_action():995] rc_action before adwrite offset 0x60, value 0x18379d
d hw_nat - start
rc action <hw_nat @ start> beforwrite offset 0x60, value 0x18b79d
e file_lock.
rc action <hw_nat @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.hw_nat.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add hw_nat - start
[rc.c::rc_start():899] Calling Start function of hw_nat
[SYSTEM]/bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
insmod: can't read '/lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko': No such file or directory
unlink running file </var/run/rc.hw_nat.run>
=============rc start
[rc debug]/usr/sbin/rc lan start
ap_name=lan action=start
[rc.c::rc_action():995] rc_action before add lan - start
rc action <lan @ start> before file_lock.
rc action <lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add lan - start
[rc.c::rc_start():899] Calling Start function of lan
[basic/lan_cfg.c::start_lan():343]
[SYSTEM]/usr/sbin/brctl setfd br0 1
[SYSTEM]/sbin/ifconfig br0 192.168.168.1 netmask 255.255.255.0 broadcast 192.168.168.255
[basic/lan_cfg.c::start_lan():382]
[SYSTEM]/usr/sbin/brctl stp br0 off
sh: cannot create /proc/http_file/getLanIp: nonexistent directory
[basic/lan_cfg.c::start_lan():395]
[basic/lan_cfg.c::start_lan():416]
[SYSTEM]echo "Set GPIO72 to GPIO mode"
Set GPIO72 to GPIO mode
[SYSTEM]reg s 0xb0000000
[SYSTEM]reg r 60
[SYSTEM]reg w 60 0x18379d
[SYSTEM]reg w 60 0x18b79d
[basic/lan_cfg.c::start_lan():439]
unlink running file </var/run/rc.lan.run>
[flash.c::sc_check_remotescfgmgrmagic():634] buf:ff, ff, ff, ff
[flash.c::sc_check_remotescfgmgrmagic():636] magic:31, 3e, c5, 8d
scfgmgr for local
[rc debug]/usr/sbin/rc printk start
ap_name=printk action=start
[rc.c::rc_action():995] rc_action before add printk - start
rc action <printk @ start> before file_lock.
rc action <printk @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.printk.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add printk - start
[rc.c::rc_start():899] Calling Start function of printk
[SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk
unlink running file </var/run/rc.printk.run>
[rc debug]/usr/sbin/rc timezone start
ap_name=timezone action=start
[rc.c::rc_action():995] rc_action before add timezone - start
rc action <timezone @ start> before file_lock.
rc action <timezone @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.timezone.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add timezone - start
[rc.c::rc_start():899] Calling Start function of timezone
[SYSTEM]/bin/echo GMT+8 > /etc/TZ
unlink running file </var/run/rc.timezone.run>
[rc debug]/usr/sbin/rc syslogd start
ap_name=syslogd action=start
[rc.c::rc_action():995] rc_action before add syslogd - start
rc action <syslogd @ start> before file_lock.
rc action <syslogd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add syslogd - start
[rc.c::rc_start():899] Calling Start function of syslogd
[SYSTEM]/sbin/syslogd -f /etc/syslog.conf
unlink running file </var/run/rc.syslogd.run>
[rc debug]/usr/sbin/rc remote_httpd start
ap_name=remote_httpd action=start
[rc.c::rc_action():995] rc_action before add remote_httpd - start
rc action <remote_httpd @ start> before file_lock.
rc action <remote_httpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.remote_httpd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add remote_httpd - start
[rc.c::rc_start():899] Calling Start function of remote_httpd
unlink running file </var/run/rc.remote_httpd.run>
[rc debug]/usr/sbin/rc dhcpd start
ap_name=dhcpd action=start
[rc.c::rc_action():995] rc_action before add dhcpd - start
rc action <dhcpd @ start> before file_lock.
rc action <dhcpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dhcpd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add dhcpd - start
[rc.c::rc_start():899] Calling Start function of dhcpd
killall: udhcpd: no process killed
unlink running file </var/run/rc.dhcpd.run>
[rc debug]/usr/sbin/rc ntp start
ap_name=ntp action=start
[rc.c::rc_action():995] rc_action before add ntp - start
rc action <ntp @ start> before file_lock.
rc action <ntp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ntp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add ntp - start
[rc.c::rc_start():899] Calling Start function of ntp
[SYSTEM]/usr/sbin/netgear_ntp -z GMT+8&
unlink running file </var/run/rc.ntp.run>
[rc debug]/usr/sbin/rc hw_nat start
ap_name=hw_nat action=start
[rc.c::rc_action():995] rc_action before add hw_nat - start
rc action <hw_nat @ start> before file_lock.
rc action <hw_nat @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.hw_nat.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add hw_nat - start
[rc.c::rc_start():899] Calling Start function of hw_nat
[SYSTEM]/bin/insmod /lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko
insmod: can't read '/lib/modules/2.6.36/kernel/net/nat/hw_nat/hw_nat.ko': No such file or directory
unlink running file </var/run/rc.hw_nat.run>
[rc debug]/usr/sbin/rc route start
ap_name=route action=start
[rc.c::rc_action():995] rc_action before add route - start
rc action <route @ start> before file_lock.
rc action <route @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.route.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add route - start
[rc.c::rc_start():899] Calling Start function of route
unlink running file </var/run/rc.route.run>
[rc debug]/usr/sbin/rc ripd start
ap_name=ripd action=start
[rc.c::rc_action():995] rc_action before add ripd - start
rc action <ripd @ start> before file_lock.
rc action <ripd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.ripd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add ripd - start
[rc.c::rc_start():899] Calling Start function of ripd
unlink running file </var/run/rc.ripd.run>
[rc debug]/usr/sbin/rc dnrd start
ap_name=dnrd action=start
[rc.c::rc_action():995] rc_action before add dnrd - start
rc action <dnrd @ start> before file_lock.
rc action <dnrd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add dnrd - start
[rc.c::rc_start():899] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.168.1:80
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.168.1
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.168.1
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]dnrd -a 192.168.168.1 -m hosts -c off -r 0 -s 8.8.8.8 &
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.168.1
Notice: caching turned off
unlink running file </var/run/rc.dnrd.run>
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
[rc debug]/usr/sbin/rc potcounter start
ap_name=potcounter action=start
[rc.c::rc_action():995] rc_action before add potcounter - start
rc action <potcounter @ start> before file_lock.
rc action <potcounter @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.potcounter.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add potcounter - start
[rc.c::rc_start():899] Calling Start function of potcounter
unlink running file </var/run/rc.potcounter.run>
[rc debug]/usr/sbin/rc lltd start
ap_name=lltd action=start
[rc.c::rc_action():995] rc_action before add lltd - start
rc action <lltd @ start> before file_lock.
rc action <lltd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.lltd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add lltd - start
[rc.c::rc_start():899] Calling Start function of lltd
unlink running file </var/run/rc.lltd.run>
[rc debug]/usr/sbin/rc usb_init start
ap_name=usb_init action=start
[rc.c::rc_action():995] rc_action before add usb_init - start
rc action <usb_init @ start> before file_lock.
rc action <usb_init @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_init.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add usb_init - start
[rc.c::rc_start():899] Calling Start function of usb_init
[SYSTEM]/bin/rm /etc/samba/secrets.tdb
rm: cannot remove '/etc/samba/secrets.tdb': No such file or directory
[SYSTEM]/usr/bin/killall -9 smbd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 nmbd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[SYSTEM]/usr/bin/killall -9 bftpd >/dev/null 2>&1
[usb_new/usb.c::sd_mount():1082] usb has unpluged, we will check if we need power off USB LED[SYSTEM]/usr/sbin/rc usb_led_control stop
[rc debug]/usr/sbin/rc usb_led_control stop
ap_name=usb_led_control action=stop
[rc.c::rc_action():995] rc_action before add usb_led_control - stop
rc action <usb_led_control @ stop> before file_lock.
rc action <usb_led_control @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_led_control.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add usb_led_control - stop
unlink running file </var/run/rc.usb_led_control.run>
[rc.c::rc_action():995] rc_action before add usb_led_control - stop
rc action <usb_led_control @ stop> before file_lock.
rc action <usb_led_control @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_led_control.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add usb_led_control - stop
unlink running file </var/run/rc.usb_led_control.run>
can't find this application
[rc.c::rc_action():995] rc_action before add usb_led_control - stop
rc action <usb_led_control @ stop> before file_lock.
rc action <usb_led_control @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.usb_led_control.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add usb_led_control - stop
[rc.c::rc_stop():937] Calling Stop function of usb_led_control
[usb/usb_led.c::usb_led_control_off():109] ---------not 3g mode-off usb------
[SYSTEM]/usr/sbin/led_app off 60
unlink running file </var/run/rc.usb_led_control.run>
unlink running file </var/run/rc.usb_init.run>
[rc debug]/usr/sbin/rc debug_mode start
ap_name=debug_mode action=start
[rc.c::rc_action():995] rc_action before add debug_mode - start
rc action <debug_mode @ start> before file_lock.
rc action <debug_mode @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.debug_mode.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add debug_mode - start
[rc.c::rc_start():899] Calling Start function of debug_mode
unlink running file </var/run/rc.debug_mode.run>
[rc debug]/usr/sbin/rc wifi_isolation start
ap_name=wifi_isolation action=start
[rc.c::rc_action():995] rc_action before add wifi_isolation - start
rc action <wifi_isolation @ start> before file_lock.
rc action <wifi_isolation @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wifi_isolation.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add wifi_isolation - start
[rc.c::rc_start():899] Calling Start function of wifi_isolation
[SYSTEM]/bin/echo "lan_ip=192.168.168.1" > /proc/wifi_isolation
sh: cannot create /proc/wifi_isolation: nonexistent directory
[SYSTEM]/bin/echo "lan_netmask=255.255.255.0" > /proc/wifi_isolation
sh: cannot create /proc/wifi_isolation: nonexistent directory
unlink running file </var/run/rc.wifi_isolation.run>
[rc debug]/usr/sbin/rc httpd start
ap_name=httpd action=start
[rc.c::rc_action():995] rc_action before add httpd - start
rc action <httpd @ start> before file_lock.
rc action <httpd @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.httpd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add httpd - start
[rc.c::rc_start():899] Calling Start function of httpd
[sc_language.c::create_language_file():426] Create link files for <English>
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock2 to ENU
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock3 to ESP
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock4 to CHS
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock5 to FRA
[sc_language.c::update_language_mtd_mapping():325] update mtd /dev/mtdblock6 to DEU
[sc_language.c::create_language_file():449] Checking MTD </dev/mtdblock2> according to its id <ENU>
[sc_language.c::decompress_language():175] Try to decompress MTD </dev/mtdblock2>
rmmod: ipt_REJECT: No such file or directory
[rc debug]/bin/rc firewall restart
ap_name=firewall action=restart
[rc.c::rc_action():995] rc_action before add firewall - restart
rc action <firewall @ restart> before file_lock.
rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add firewall - restart
unlink running file </var/run/rc.firewall.run>
[rc.c::rc_action():995] rc_action before add firewall - restart
rc action <firewall @ restart> before file_lock.
rc action <firewall @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.firewall.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add firewall - restart
[rc.c::rc_stop():937] Calling Stop function of firewall
[SYSTEM]echo 0 > /proc/sys/net/ipv4/ip_forward
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
[SYSTEM]echo 1 > /proc/sys/net/ipv4/conf/wlan0-va0/forwarding
sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
[rc.c::rc_start():899] Calling Start function of firewall
[SYSTEM]/usr/sbin/rc syslogd create;/usr/bin/killall -SIGUSR2 syslogd &
[rc debug]/usr/sbin/rc syslogd create
ap_name=syslogd action=create
[rc.c::rc_action():995] rc_action before add syslogd - create
rc action <syslogd @ create> before file_lock.
rc action <syslogd @ create lock = 4> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.syslogd.run
rc action < unlock = 4> after file_lock.
[rc.c::rc_action():1003] rc_action after add syslogd - create
[rc.c::rc_create():979] Calling Create function of syslogd
unlink running file </var/run/rc.syslogd.run>
[SYSTEM]/bin/echo switch=on > /proc/net/spi_enable
[SYSTEM]/bin/echo clear > /proc/net/firewall_block
[SYSTEM]/bin/echo clear > /proc/net/clamp_total_session_for_one_src
[SYSTEM]/bin/echo clear > /proc/net/psd_udp_tcp_vanilla_port_scan
[SYSTEM]/bin/echo clear > /proc/net/echo_chargen_config
[SYSTEM]/bin/echo wan_if=eth2.2 > /proc/net/spi_enable
[SYSTEM]/bin/echo spi=enable > /proc/net/spi_enable
[SYSTEM]/usr/sbin/killall -9 usb_httpd
killall: usb_httpd: no process killed
[SYSTEM]/bin/echo "enable_ipmac=0" > /proc/arp_protect_enable
sh: cannot create /proc/arp_protect_enable: nonexistent directory
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Bad argument `DROP'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `CNAPT'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `HAIRPIN'
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.10: option `--eaddr' requires an argument
Try `iptables -h' or 'iptables --help' for more information.
Using intrapositioned negation (`--option ! this`) is deprecated in favor of extrapositioned (`! --option this`).
Bad argument `DNAT'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `DNAT'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `DNAT'
Try `iptables -h' or 'iptables --help' for more information.
Bad argument `DNAT'
Try `iptables -h' or 'iptables --help' for more information.
iptables v1.4.10: option `--eaddr' requires an argument
Try `iptables -h' or 'iptables --help' for more information.
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.168.1
[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab
[SYSTEM]/bin/echo GMT+8 > /etc/TZ
[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule
sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory
unlink running file </var/run/rc.firewall.run>
[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR PR2000" -c '**.cgi' -t 300&
unlink running file </var/run/rc.httpd.run>
[rc debug]/usr/sbin/rc wlan start
ap_name=wlan action=start
[rc.c::rc_action():995] rc_action before add wlan - start
rc action <wlan @ start> before file_lock.
rc action <wlan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.wlan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add wlan - start
[rc.c::rc_start():899] Calling Start function of wlan
[SYSTEM]brctl addif br0 ra0
[SYSTEM]brctl addif br0 rai0
interface rai0 does not exist!
[SYSTEM]/usr/sbin/wsc_daemon &
sh: /usr/sbin/wsc_daemon: not found
[SYSTEM]mkdir -p /etc/Wireless/RT2860
[wifi_mtk/wifi.c::create_ralink_driver_conf():829] NOT apcli mode, follow spec to show extchannel
[SYSTEM]mkdir -p /etc/Wireless/iNIC
[wifi_mtk/wifi.c::create_ralink_driver_conf():829] NOT apcli mode, follow spec to show extchannel
[wifi_mtk/wifi.c::pr2000_wifidata_modify():1323] ra0 e2p:
[0x0050]:0xFFFF
[wifi_mtk/wifi.c::prepare_single_sku():1226] current wifi region is North America
[wifi_mtk/wifi.c::prepare_single_sku():1232] ======wifi region is North America, we will use /etc_ro/Wireless/RT2860AP/FCC.dat========
[SYSTEM]echo 1 > /tmp/apcli_wifi_if_inited
[SYSTEM]/sbin/ifconfig ra0 up
[SYSTEM]/bin/led_app on 40
[libscm_wl.c::GenerateUUID():121]
GUI ASCII string: 38833092-3092-1883-87c7-6cb0ce7172d8
[libscm_wl.c::GenerateUUID():122]
GUI HEX string: 388330923092188387c76cb0ce7172d8
[SYSTEM]/usr/bin/killall miniupnpd_wsc
killall: miniupnpd_wsc: no process killed
[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh
[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh
+ iwpriv ra0 set WscConfMode=0
+ iwpriv rai0 set WscConfMode=0
+ iwpriv ra0 set WscSetupLock=0
+ iwpriv rai0 set WscSetupLock=0
+ route add -host 239.255.255.250 dev br0
+ iwpriv ra0 set WscConfMode=7
+ miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -i eth2.2 -a 192.168.168.1 -n 7777 -u 38833092-3092-1883-87c7-6cb0ce7172d8
Unknown option: -I
Unknown option: ra0
[SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptime
[SYSTEM]/usr/sbin/led_app on 45
[SYSTEM]iwpriv rai0 mac 1328=331d0f05
rai0 no private ioctls.
[SYSTEM]/sbin/iwpriv ra0 set DyncVgaEnable=0
[SYSTEM]/usr/bin/killall apcli_monitor
killall: apcli_monitor: no process killed
[wifi_mtk/apcli.c::is_apcli_ok_to_start():42] check if device is ready to start apcli
[wifi_mtk/apcli.c::_dump_apcli_masterap_config():15] ===dump apcli apcli config===
apcli_act_as_wan:1
apcli_remoteap_ssid:
apcli_remoteap_bssid:
apcli_remoteap_auth:
apcli_remoteap_encry:
apcli_remoteap_wpakey:
apcli_remoteap_wep_key:
apcli_remoteap_wep_keyidx:
apcli_remoteap_wep_keytype:
[wifi_mtk/apcli.c::is_apcli_ok_to_start():85] wait pr_wizard
[wifi_mtk/apcli.c::is_apcli_ok_to_start():93] NOT start apcli
unlink running file </var/run/rc.wlan.run>
=============rc finish
[ pr_wiz_fsm - 563 ]enter
[ pr_wiz_fsm - 570 ]state = DEV_STATE_BOOT
[ pr_wiz_start_dns_hijack - 253 ]enter
[rc debug]/sbin/rc dnrd restart
ap_name=dnrd action=restart
[rc.c::rc_action():995] rc_action before add dnrd - restart
rc action <dnrd @ restart> before file_lock.
rc action <dnrd @ restart lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.dnrd.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add dnrd - restart
[rc.c::rc_stop():937] Calling Stop function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.168.1:80
[rc debug]/usr/sbin/rc upnp start
ap_name=upnp action=start
[rc.c::rc_action():995] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
[rc.c::rc_action():995] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add upnp - start
unlink running file </var/run/rc.upnp.run>
can't find this application
[rc.c::rc_action():995] rc_action before add upnp - start
rc action <upnp @ start> before file_lock.
rc action <upnp @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.upnp.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add upnp - start
[rc.c::rc_start():899] Calling Start function of upnp
[SYSTEM]route add -net 239.0.0.0 netmask 255.0.0.0 br0
[SYSTEM]/usr/sbin/miniupnpd -i eth2.2 -a 192.168.168.1 -p 56688 -U -t 1800 -T 4 -u 824ff22b-8c7d-41c5-a131-6cb0ce7172d8
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.168.1
unlink running file </var/run/rc.upnp.run>
route: SIOCADDRT: File exists
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.168.1
/usr/etc/rcS: line 275: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory
/usr/etc/rcS: line 276: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory
/usr/etc/rcS: line 280: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
[rc.c::rc_start():899] Calling Start function of dnrd
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.168.1:80
min free is 10519
[rc debug]/usr/sbin/rc reset_lan start
ap_name=reset_lan action=start
[rc.c::rc_action():995] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
iptables: No chain/target/match by that name.
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
[rc.c::rc_action():995] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.168.1
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add reset_lan - start
unlink running file </var/run/rc.reset_lan.run>
can't find this application
[rc.c::rc_action():995] rc_action before add reset_lan - start
rc action <reset_lan @ start> before file_lock.
rc action <reset_lan @ start lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.reset_lan.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add reset_lan - start
[rc.c::rc_start():899] Calling Start function of reset_lan
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.168.1
iptables: No chain/target/match by that name.
[SYSTEM]killall -9 dnrd
killall: dnrd: no process killed
[SYSTEM]iptables -t nat -D PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.168.1
iptables: No chain/target/match by that name.
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p udp --dport 53 -j DNAT --to 192.168.168.1
[SYSTEM]iptables -t nat -I PREROUTING -i br0 -p tcp --dport 80 -j DNAT --to 192.168.168.1:80
[SYSTEM]dnrd -a 192.168.168.1 -m hosts -c off -g routerlogin.com &
unlink running file </var/run/rc.dnrd.run>
[ pr_wiz_reset_wan_settings - 538 ]enter
Notice: caching turned off
Warning: Using /etc/hosts will be removed in a future version. Please use only the /etc/dnrd/master file or use -m off.
[rc debug]/sbin/rc wan stop
[SYSTEM]/usr/bin/killall netgear_ntp
[SYSTEM]/usr/bin/killall -SIGUSR2 miniupnpd
killall: ripd: no process killed
killall: zebra: no process killed
killall: ripd: no process killed
killall: zebra: no process killed
[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -t nat -F POSTROUTING
[SYSTEM]/usr/sbin/iptables -t nat -A POSTROUTING -o eth2.2 -j MASQUERADE
[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv4/conf/br0/forwarding
[SYSTEM]/usr/sbin/iptables -D PRE_BASIC -t nat -i eth2.2 -d ! (null) -j DROP
sh: syntax error: "(" unexpected
[SYSTEM]/bin/echo "#!/bin/sh" > /etc/ppp/ip-down
[SYSTEM]/usr/bin/killall pppd
killall: pppd: no process killed
[SYSTEM]/usr/bin/killall openl2tpd
killall: openl2tpd: no process killed
[SYSTEM]/usr/bin/killall udhcpc
killall: udhcpc: no process killed
[SYSTEM]/usr/bin/killall pppoe-relay
killall: pppoe-relay: no process killed
[SYSTEM]/sbin/ifconfig eth2.2 0.0.0.0 >/dev/null 2>&1
[ pr_wiz_reset_wan_settings - 538 ]enter
[ pr_profile_filter_read - 473 ]enter
[ pr_profile_lock - 44 ]lock fd = -1, user = 0
[ pr_profile_unlock - 59 ]lock fd = 3, user = 1
[ pr_wiz_fsm - 600 ]no NODECT profile in this mode
[ pr_wiz_fsm - 612 ]wan port no link, to DEV_STATE_WIRED_NO_CABLE
[ pr_wiz_fsm - 570 ]state = DEV_STATE_WIRED_NO_CABLE
unlink running file </var/run/rc.reset_lan.run>
cable_down_once
[rc debug]/usr/sbin/rc down_manage stop
ap_name=down_manage action=stop
[rc.c::rc_action():995] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
[rc.c::rc_action():995] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
can't find this application
[rc.c::rc_action():995] rc_action before add down_manage - stop
rc action <down_manage @ stop> before file_lock.
rc action <down_manage @ stop lock = 3> after file_lock.
[SYSTEM]/bin/cp /proc/uptime /var/run/rc.down_manage.run
killall: udhcpc: no process killed
rc action < unlock = 3> after file_lock.
[rc.c::rc_action():1003] rc_action after add down_manage - stop
unlink running file </var/run/rc.down_manage.run>
can't find this application
Path: .
URL: http://sdcsvn.sdc.sercomm.com/svn/WNR25 … hes/PR2000
Repository Root: http://sdcsvn.sdc.sercomm.com/svn/WNR2500
Repository UUID: ba50b1f2-a9a7-11df-84b5-2b521ff782fd
Revision: 4576
Node Kind: directory
Schedule: normal
Last Changed Author: jhoshua_jiang
Last Changed Rev: 4575
Last Changed Date: 2015-02-14 05:16:58 +0800 (Sat, 14 Feb 2015)
VERSION: V1.0.0.14_1.0.1
Build from: localhost.localdomain /home/jhoshua/project/PR2000_1014/PR2000 by jhoshua
DATE: Fri Feb 13 17:24:21 CST 2015
BOARD_ID: PR2000
PID USER VSZ STAT COMMAND
1 root 1600 S init
2 root 0 SW [kthreadd]
3 root 0 SW [ksoftirqd/0]
4 root 0 SW [kworker/0:0]
5 root 0 SW [kworker/u:0]
6 root 0 SW< [khelper]
7 root 0 SW [sync_supers]
8 root 0 SW [bdi-default]
9 root 0 SW< [kblockd]
10 root 0 SW [khubd]
11 root 0 SW [kswapd0]
12 root 0 SW< [crypto]
17 root 0 SW [mtdblock0]
18 root 0 SW [mtdblock1]
19 root 0 SW [mtdblock2]
20 root 0 SW [mtdblock3]
21 root 0 SW [mtdblock4]
22 root 0 SW [mtdblock5]
23 root 0 SW [mtdblock6]
24 root 0 SW [mtdblock7]
25 root 0 SW [mtdblock8]
26 root 0 SW [mtdblock9]
27 root 0 SW [mtdblock10]
28 root 0 SW [mtdblock11]
29 root 0 SW [mtdblock12]
30 root 0 SW [mtdblock13]
31 root 0 SW [mtdblock14]
32 root 0 SW [mtdblock15]
33 root 0 SW [mtdblock16]
34 root 0 SW [mtdblock17]
35 root 0 SW [mtdblock18]
36 root 0 SW [kworker/u:1]
43 root 0 SW [kworker/0:1]
45 root 1600 S /bin/sh /usr/etc/rcS
116 root 1140 S /sbin/klogd
118 root 836 S /usr/sbin/cmd_agent_ap
120 root 836 S /usr/sbin/cmd_agent_ap_3g
122 root 836 S /usr/sbin/cmd_agent_ap_rc
248 root 1388 S /usr/sbin/led_switch
406 root 0 SW [RtmpCmdQTask]
407 root 0 SW [RtmpWscTask]
476 root 1696 S /usr/sbin/scfgmgr
493 root 1200 S /sbin/syslogd -f /etc/syslog.conf
503 root 908 S /usr/sbin/udhcpd /etc/udhcpd.conf
886 root 1244 S /usr/bin/lld2 br0
915 root 856 S telnetenabled 192.168.168.1 6CB0CE7172D8 Gearguy Gear
1379 root 1960 S /usr/sbin/mini_httpd -d /www -r NETGEAR PR2000 -c **.
1413 root 1008 S miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -
1569 root 2036 S /usr/sbin/miniupnpd -i eth2.2 -a 192.168.168.1 -p 566
1571 root 860 S /usr/sbin/crond
1572 root 1392 S /usr/sbin/multi_pb_app 90 10 50
1628 root 0 Z [crond]
1629 root 0 Z [crond]
1801 root 844 S /usr/sbin/cmd_agent
2286 root 1920 S dnrd -a 192.168.168.1 -m hosts -c off -g routerlogin.
2505 root 1392 S usr/sbin/wan_monitor
2527 root 0 SW [ telnetDBGD ]
2528 root 0 SW [ acktelnetDBGD ]
2529 root 0 SW [checkSBusTimeou]
2531 root 0 SW [NU UDP]
2532 root 0 SW [NU TCP]
2534 root 1600 R /bin/ps
starting pid 2536, tty '/dev/ttyS1': '/bin/sh'
# INFO14AE: Bind to br0
####################################
I'm not 100% sure where to go from here, but this was just step 1. Now its time to learn step 2. I hope this info helps, and if anyone can give me any guidance from this point on I would appreciate it.
Ok, more specifically firmware is V1.0.0.14_1.0.1.
Telnet worked with Login: root and no password. I thought I had tried that, guess not.
Some info from telnet. I know some has been posted already, I was just poking around. Heres a full copy:
#######################################
PR2000 login: root
Welcome to
_______ _______ ___ __ ____ _ _ ___
| ___ \| __ || | |__|| \ | || | / /
| |___| || |__| || |__ __ | \| || |/ /
| _ /| _ || || || |\ || \
|__| \__\|__| |__||______||__||_| \____||_|\___\
=System Architecture Department=
# ls
bin etc_ro lib proc tmp www
dev home media sbin usr www.eng
etc init mnt sys var
# cat /proc/cpuinfo
system type : Ralink SoC
processor : 0
cpu model : MIPS 24Kc V5.0
BogoMIPS : 386.04
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ff8, 0x0ff8, 0x03bb, 0x0ff8]
ASEs implemented : mips16 dsp
shadow register sets : 1
core : 0
VCED exceptions : not available
VCEI exceptions : not available
# cat /proc/meminfo
MemTotal: 60512 kB
MemFree: 35968 kB
Buffers: 2236 kB
Cached: 7216 kB
SwapCached: 0 kB
Active: 5144 kB
Inactive: 6044 kB
Active(anon): 1736 kB
Inactive(anon): 32 kB
Active(file): 3408 kB
Inactive(file): 6012 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 1760 kB
Mapped: 1108 kB
Shmem: 32 kB
Slab: 7448 kB
SReclaimable: 676 kB
SUnreclaim: 6772 kB
KernelStack: 520 kB
PageTables: 332 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 30256 kB
Committed_AS: 5432 kB
VmallocTotal: 1048372 kB
VmallocUsed: 5460 kB
VmallocChunk: 1026216 kB
# cat /etc/passwd
root::0:0:root:/:/bin/sh
nobody::99:99:Nobody:/:/sbin/sh
# /sbin/lsmod
Module Size Used by
NetUSB 186484 0
GPL_NetUSB 3636 1 NetUSB
usbserial_filter 1728 0
usb_storage 38072 0
ipt_REJECT 136779 1
rt2860v2_ap 1994612 1
others_dos 1258 0
clamp_total_session_for_one_src 138010 0
tcp_syn_dos 23719 0
psd_and_special_udp_dos 898328 0
fake_source_dos 1945 0
firewall_block 10796 0
common 1644 2 psd_and_special_udp_dos,fake_source_dos
natlimit 4304 1
hairpin 1536 2
cudp 880 1
cdmz 1328 0
calg 3248 0
cpm 6400 0
cpt 7216 0
cnapt 1408 2
cnapt_core 16041 7 hairpin,cudp,cdmz,calg,cpm,cpt,cnapt
xt_ct_dir 646 1
ipt_DLOG 1168 6
ipt_dnshj 1328 1
ipt_http_string 6336 0
ipt_condition 1664 0
led_hw 1840 0
led_pb_api 6298 1 led_hw
# ls -l /
lrwxrwxrwx 1 root root 9 Feb 13 2015 bin -> usr/sbin/
drwxr-xr-x 3 root root 0 Dec 31 1969 dev
lrwxrwxrwx 1 root root 8 Feb 13 2015 etc -> /tmp/etc
lrwxrwxrwx 1 root root 11 Feb 13 2015 etc_ro -> /tmp/etc_ro
drwxr-xr-x 2 root root 3 Dec 2 2012 home
lrwxrwxrwx 1 root root 11 Feb 13 2015 init -> bin/busybox
drwxr-xr-x 4 root root 1919 Feb 13 2015 lib
drwxr-xr-x 2 root root 0 Dec 31 1969 media
lrwxrwxrwx 1 root root 8 Feb 13 2015 mnt -> /tmp/mnt
dr-xr-xr-x 77 root root 0 Dec 31 1969 proc
lrwxrwxrwx 1 root root 9 Feb 13 2015 sbin -> usr/sbin/
drwxr-xr-x 11 root root 0 Dec 31 1969 sys
drwxr-xr-x 10 root root 0 Oct 15 23:36 tmp
drwxr-xr-x 10 root root 151 May 15 2013 usr
lrwxrwxrwx 1 root root 8 Feb 13 2015 var -> /tmp/var
lrwxrwxrwx 1 root root 8 Feb 13 2015 www -> /tmp/www
drwxr-xr-x 7 root root 15813 Feb 13 2015 www.eng
# ls -l /etc/
-rwxr-xr-x 1 root root 136 Feb 11 2015 3g
-rwxr-xr-x 1 root root 202 Feb 11 2015 3g.chat
-rw-r--r-- 1 root root 6 Oct 15 23:34 TZ
drwxr-xr-x 4 root root 0 Dec 31 1969 Wireless
-rwxr-xr-x 1 root root 12239 Feb 13 2015 bftpd.conf
-r-xr-xr-x 1 root root 1025 Dec 31 1969 block.htm
prw-r--r-- 1 root root 0 Dec 31 1969 cmd_agent
prw-r--r-- 1 root root 0 Dec 31 1969 cmd_agent_3g
prw-r--r-- 1 root root 0 Oct 15 23:34 cmd_agent_rc
-rw-r--r-- 1 root root 265 Oct 15 23:34 crontab
-rw-r--r-- 1 root root 10131 Feb 13 2015 default
-rwxr-xr-x 1 root root 1062 Feb 11 2015 dhclient-enter-hook.in
-rwxr-xr-x 1 root root 484 Feb 11 2015 dht.dat
drwxr-xr-x 2 root root 0 Dec 31 1969 dnrd
-rwxr-xr-x 1 root root 385 Feb 11 2015 do.sh
-rwxr-xr-x 1 root root 11132 Feb 11 2015 dongle_cmd
-rwxr-xr-x 1 root root 182388 Feb 11 2015 dongle_mgnt
-rwxr-xr-x 1 root root 104076 Feb 11 2015 dongle_monitor
-rwxr-xr-x 1 root root 453 Feb 11 2015 dongle_reboot.sh
lrwxrwxrwx 1 root root 26 Dec 31 1969 download_job.cgi -> /usr/sbin/download_job.cgi
-rwxr-xr-x 1 root root 306 Feb 11 2015 enlarge_mem_reclaim_threshold.sh
-rw-r--r-- 1 root root 56 Dec 31 1969 err401.htm
-rw-r--r-- 1 root root 318 Feb 11 2015 fstab
-rw-r--r-- 1 root root 25 Feb 11 2015 group
-rwxr-xr-x 1 root root 353 Feb 11 2015 gsmtd.conf
-rw-r--r-- 1 root root 10 Dec 31 1969 gui_version
-rw-r--r-- 1 root root 276 Oct 15 23:36 hosts
-rw-r--r-- 1 root root 15 Dec 31 1969 htpasswd
lrwxrwxrwx 1 root root 28 Dec 31 1969 htpwd_recovery.cgi -> /usr/sbin/htpwd_recovery.cgi
-rw-r--r-- 1 root root 46 Feb 11 2015 inittab
drwxr-xr-x 3 root root 0 Feb 13 2015 iproute2
drwxr-xr-x 3 root root 0 Feb 11 2015 l2tp
lrwxrwxrwx 1 root root 17 Dec 31 1969 language -> /tmp/language/ENU
-rw-r--r-- 1 root root 48 Feb 11 2015 lld2d.conf
-rwxr-xr-x 1 root root 4983 Feb 11 2015 makedevlinks
-rw-r--r-- 1 root root 1778 Feb 11 2015 mini_httpd.pem
-rw-r--r-- 1 root root 325 Feb 11 2015 motd
-rwxr-xr-x 1 root root 5548 Feb 11 2015 msg_send_robot
-rw-r--r-- 1 root root 120 Feb 11 2015 naptd.conf.orig
-rw-r--r-- 1 root root 10 Oct 15 23:34 new_gui_version
-rw-r--r-- 1 root root 9 Oct 15 23:34 new_version
-rw-r--r-- 1 root root 57 Feb 11 2015 passwd
drwxr-xr-x 5 root root 0 Dec 31 1969 ppp
-rwxr-xr-x 1 root root 1452 Feb 11 2015 prepare_3g
-rwxr-xr-x 1 root root 9120 Feb 11 2015 rcS
-rw-r--r-- 1 root root 7947 Feb 11 2015 rcS.MT
-rwxr-xr-x 1 root root 139 Feb 11 2015 reboot
-rwxr-xr-x 1 root root 225 Feb 11 2015 remove.sh
-rw-r--r-- 1 root root 48 Dec 31 1969 resolv.conf
lrwxrwxrwx 1 root root 28 Dec 31 1969 restore_config.cgi -> /usr/sbin/restore_config.cgi
drwxr-xr-x 2 root root 0 Feb 13 2015 samba
drwxr-xr-x 2 root root 0 Feb 13 2015 samba.conf
lrwxrwxrwx 1 root root 19 Dec 31 1969 setup.cgi -> /usr/sbin/setup.cgi
-rw-r--r-- 1 root root 6199 Feb 11 2015 simplecfgservice.xml
-rw-r--r-- 1 root root 523 Feb 13 2015 svn.info
-rw-r--r-- 1 root root 262 Dec 31 1969 syslog.conf
drwxr-xr-x 4 root root 0 Feb 11 2015 udev
-rwxr-xr-x 1 root root 2119 Feb 11 2015 udhcpc.ap.script
-rwxr-xr-x 1 root root 2759 Feb 11 2015 udhcpc.apcli.script
-rwxr-xr-x 1 root root 958 Feb 11 2015 udhcpc.failover.script
-rwxr-xr-x 1 root root 973 Feb 11 2015 udhcpc.failoverpptpc.script
-rwxr-xr-x 1 root root 1597 Feb 11 2015 udhcpc.fix.script
-rwxr-xr-x 1 root root 1655 Feb 11 2015 udhcpc.l2tp.script
-rwxr-xr-x 1 root root 1438 Feb 11 2015 udhcpc.pppoe.script
-rwxr-xr-x 1 root root 1581 Feb 11 2015 udhcpc.pptpc.script
-rwxr-xr-x 1 root root 2512 Feb 11 2015 udhcpc.script
-rwxr-xr-x 1 root root 894 Feb 11 2015 udhcpc.wizard.script
-rw-r--r-- 1 root root 178 Dec 31 1969 udhcpd.conf
-rw-r--r-- 1 root root 0 Dec 31 1969 udhcpd.reserved_info
lrwxrwxrwx 1 root root 27 Dec 31 1969 upgrade_flash.cgi -> /usr/sbin/upgrade_flash.cgi
lrwxrwxrwx 1 root root 19 Dec 31 1969 upgrade_stringTbl.cgi -> /usr/sbin/setup.cgi
drwxr-xr-x 3 root root 0 Feb 11 2015 usb
-rw-r--r-- 1 root root 0 Dec 31 1969 usb_httpd.conf
-rw-r--r-- 1 root root 16 Feb 13 2015 version
#
#######################################
(Last edited by xaxx on 22 Oct 2015, 16:07)
nice work.
One word of caution with the PR2000.
It appears to have a known failure mode when plugged into any AC outlet with a surge suppressor.
In our office, it works great when plugged into a normal wall outlet.
When I plug it into a power strip with a surge suppressor inside, it drops Wi-Fi or reboots every couple of minutes, making it impossible to maintain connectivity.
I recently plugged it into a normal wall outlet inside a fire department EOC, and it behaved the same way. When I asked "there's a whole-building surge suppressor in the electrical panel, right", the answer was affirmative, and I put the Trek aside.
I found one reference to this as being the cause, and lots of threads complaining about the problem, without a good solution.
If it weren't for that issue, I'd give it five stars.
@somni: Thanks, we'll see if it ends up being worth the time.
@PetesGuide: I noticed some odd power behavior with 5V/1A USB vs. A/C. I never saw that specific type of behavior and I was plugged into a power strip with surge protection or a UPS with surge protection at least some of the time. Do you get the same issue if you use a USB power source on a surge protector? Also, what hardware revision is your PR2000?
Has anyone attempted yet? Or had any luck yet? I just picked up this PR2000 because PureVPN claimed to support the default firmware. Once I unboxed, PureVPN changed their tune and no longer support Netgear. This is sad for me. I travel frequently for work and was looking forward to packing this instead of my Asus RT-N16 ... smaller footprint, and I only need 1 LAN port for my Roku.
please please please someone get OpenWRT working onboard this!!!
I wanted to ask times whether there is now a Openwrt release for this great TravelRouter or is in the works?
Seeking namely also a OpenWTR firmware for the "Netgear N300 Trek PR2000 Travel Router, Range Extender, Repeaterund Ethernet Bridge"
Thank you for your support.
Pauline
The discussion might have continued from here.