I have TL-WR703N v1 based board with Barrier Breaker r39365 / LuCI Trunk (svn-r10471) installed.
Yesterday, when i started to set it up in repeater mode to work in pair with main router i've quickly found out that channel 12/13 are disabled in firmware and i need to apply a well know reghack patch in order to enable normal european wi-fi operation.
After applying a reghack (i beleive it was successful) i can set country and it doesn't reset to 'US' after reboot anymore, but i still can't change wireless channel to anything above 11.
Channels with US default reg set (after applying reghack):
Frequencies:
* 2412 MHz [1] (27.0 dBm)
* 2417 MHz [2] (27.0 dBm)
* 2422 MHz [3] (27.0 dBm)
* 2427 MHz [4] (27.0 dBm)
* 2432 MHz [5] (27.0 dBm)
* 2437 MHz [6] (27.0 dBm)
* 2442 MHz [7] (27.0 dBm)
* 2447 MHz [8] (27.0 dBm)
* 2452 MHz [9] (27.0 dBm)
* 2457 MHz [10] (27.0 dBm)
* 2462 MHz [11] (27.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)Tried to set 'BO' with no success, even max power stays at 27dBm. Then set it to 'JP' just to test in case something wrong with 'BO'
Part of logread while booting with 'JP':
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.750000] cfg80211: Calling CRDA to update world regulatory domain
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.750000] cfg80211: World regulatory domain updated:
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.760000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.760000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.770000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.780000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.790000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.800000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: EEPROM regdomain: 0x0
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: EEPROM indicates default country code should be used
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: doing EEPROM country->regdmn map search
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: country maps to regdmn code: 0x3a
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: Country alpha2 being used: US
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.960000] ath: Regpair used: 0x3a
Thu Jan 1 03:00:11 1970 kern.debug kernel: [ 8.970000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.980000] cfg80211: Calling CRDA for country: US
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.980000] cfg80211: Regulatory domain changed to country: US
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.990000] cfg80211: DFS Master region FCC
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 8.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.010000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 1700 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.020000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.020000] cfg80211: (5490000 KHz - 5600000 KHz @ 80000 KHz), (300 mBi, 2400 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.030000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2400 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.040000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 3000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.050000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
Thu Jan 1 03:00:11 1970 kern.info kernel: [ 9.060000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.080000] cfg80211: Calling CRDA for country: JP
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.090000] cfg80211: Regulatory domain changed to country: JP
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.100000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.110000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.110000] cfg80211: (4910000 KHz - 4990000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.120000] cfg80211: (5030000 KHz - 5090000 KHz @ 40000 KHz), (N/A, 2300 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
Thu Jan 1 03:00:15 1970 kern.info kernel: [ 15.140000] cfg80211: (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2300 mBm)iw list:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)I can't flash any other OpenWRT build, i can't change main router channel from 13.
What i'm doing wrong?
Any help would be very appreciated.
Thanks in advance