Hi folks!
I am experiencing some really bizarre problems with my OpenWrt installtion. I am running Barrier Braker on a TP-LINK WDR3600 as a torrent client behind an OpenVPN connection. I used a 32GB USB Stick attached to the second UBS port for storing torrents and a 4GB LG stick attached to the first USB port for overlay and swap.
Couple of days ago the 32GB USB stick failed so today I replaced it with a new 64GB SanDisk. The moment I rebooted the router with the USB in it however, something weird happened - the router was not accessible from my machine. At first I thought it didn't boot properly, but after further inspection it turned out it's booted, but with a completely new root folder, as if the router has been flashed clean. Taking the USB stick out and rebooting the router brings it back to its normal condition.
I have tried using different USB sticks since then, but the same thing always happens. I suspect it has something to do with overlay not functioning properly but I have no idea what it could possibly be, as I haven't changed anything at all, just replaced the USB stick.
Here's my fstab:
config global
option anon_swap '0'
option anon_mount '0'
option auto_swap '1'
option auto_mount '1'
option delay_root '15'
option check_fs '0'
config swap
option device '/dev/sda2'
option enabled '0'
config mount
option enabled '1'
option device '/dev/sda1'
option fstype 'ext4'
option target '/overlay'
option enabled_fsck '1'
And here's the system log when booting the router with a USB stick inserted in USB2:
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 4.670000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 4.700000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 4.700000] hub 1-0:1.0: USB hub found
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 4.710000] hub 1-0:1.0: 1 port detected
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 5.030000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 5.180000] hub 1-1:1.0: USB hub found
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 5.180000] hub 1-1:1.0: 4 ports detected
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 5.470000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 5.660000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 6.450000] eth0: link up (1000Mbps/Full duplex)
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 8.350000] jffs2: notice: (374) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (1 unchecked, 20 orphan) and 34 of xref (0 dead, 20 orphan) found.
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 9.020000] SCSI subsystem initialized
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 9.030000] usb-storage 1-1.1:1.0: USB Mass Storage device detected
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 9.040000] scsi0 : usb-storage 1-1.1:1.0
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 9.050000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 9.050000] scsi1 : usb-storage 1-1.2:1.0
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 9.060000] usbcore: registered new interface driver usb-storage
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.050000] scsi 0:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.060000] scsi 1:0:0:0: Direct-Access LG USB Drive 1100 PQ: 0 ANSI: 0 CCS
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.070000] sd 0:0:0:0: [sda] 121438208 512-byte logical blocks: (62.1 GB/57.9 GiB)
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.080000] sd 0:0:0:0: [sda] Write Protect is off
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 10.080000] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.080000] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.090000] sd 1:0:0:0: [sdb] 7864320 512-byte logical blocks: (4.02 GB/3.75 GiB)
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.100000] sd 1:0:0:0: [sdb] Write Protect is off
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 10.110000] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.110000] sd 1:0:0:0: [sdb] No Caching mode page found
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.110000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.120000] sd 1:0:0:0: [sdb] No Caching mode page found
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.130000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 10.140000] sda: sda1
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.150000] sd 0:0:0:0: [sda] Attached SCSI removable disk
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 10.180000] sdb: sdb1 sdb2
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.190000] sd 1:0:0:0: [sdb] No Caching mode page found
Wed Oct 1 12:01:10 2014 kern.err kernel: [ 10.200000] sd 1:0:0:0: [sdb] Assuming drive cache: write through
Wed Oct 1 12:01:10 2014 kern.notice kernel: [ 10.200000] sd 1:0:0:0: [sdb] Attached SCSI removable disk
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 15.300000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 15.340000] eth0: link down
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.900000] NET: Registered protocol family 10
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.920000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.930000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.940000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.950000] Backport generated by backports.git backports-20140320-37-g5c33da0
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 16.960000] ip_tables: (C) 2000-2006 Netfilter Core Team
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.000000] xt_time: kernel timezone is -0000
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.030000] cfg80211: Calling CRDA to update world regulatory domain
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.030000] cfg80211: World regulatory domain updated:
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.040000] cfg80211: DFS Master region: unset
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.040000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.050000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.060000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.070000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.080000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.080000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.090000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.100000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.110000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.150000] PPP generic driver version 2.4.2
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.170000] NET: Registered protocol family 24
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: EEPROM regdomain: 0x0
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: EEPROM indicates default country code should be used
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: doing EEPROM country->regdmn map search
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: country maps to regdmn code: 0x3a
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: Country alpha2 being used: US
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.230000] ath: Regpair used: 0x3a
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.250000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.250000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
Wed Oct 1 12:01:10 2014 kern.warn kernel: [ 17.270000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: EEPROM regdomain: 0x0
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: EEPROM indicates default country code should be used
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: doing EEPROM country->regdmn map search
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: country maps to regdmn code: 0x3a
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: Country alpha2 being used: US
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.280000] ath: Regpair used: 0x3a
Wed Oct 1 12:01:10 2014 kern.debug kernel: [ 17.290000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.290000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.300000] cfg80211: Calling CRDA for country: US
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.320000] cfg80211: Regulatory domain changed to country: US
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.330000] cfg80211: DFS Master region: FCC
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.330000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.340000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.350000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.360000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.370000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
Wed Oct 1 12:01:10 2014 kern.info kernel: [ 17.380000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
Wed Oct 1 12:01:12 2014 user.emerg syslog: 'radio0' is disabled
Wed Oct 1 12:01:12 2014 user.emerg syslog: 'radio1' is disabled
Wed Oct 1 12:01:12 2014 user.emerg syslog: 'radio0' is disabled
Wed Oct 1 12:01:12 2014 user.emerg syslog: 'radio1' is disabled
Wed Oct 1 12:01:14 2014 authpriv.info dropbear[905]: Not backgrounding
Wed Oct 1 12:01:15 2014 user.emerg syslog: setting up led USB1
Wed Oct 1 12:01:15 2014 user.emerg syslog: setting up led USB2
Wed Oct 1 12:01:15 2014 user.emerg syslog: setting up led WLAN2G
Wed Oct 1 12:01:15 2014 user.emerg syslog: - init complete -
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.930000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.930000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.950000] device eth0.1 entered promiscuous mode
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.950000] device eth0 entered promiscuous mode
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'lan' is enabled
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'lan' is setting up now
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'lan' is now up
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'loopback' is enabled
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'loopback' is setting up now
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'loopback' is now up
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.970000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
Wed Oct 1 12:01:16 2014 kern.info kernel: [ 24.980000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'wan' is enabled
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Network device 'lo' link is up
Wed Oct 1 12:01:16 2014 daemon.notice netifd: Interface 'loopback' has link connectivity
Wed Oct 1 12:01:16 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.780000] eth0: link up (1000Mbps/Full duplex)
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Network device 'eth0' link is up
Wed Oct 1 12:01:17 2014 daemon.notice netifd: VLAN 'eth0.2' link is up
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan' has link connectivity
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan' is setting up now
Wed Oct 1 12:01:17 2014 daemon.notice netifd: VLAN 'eth0.1' link is up
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.800000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.800000] br-lan: port 1(eth0.1) entered forwarding state
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.810000] br-lan: port 1(eth0.1) entered forwarding state
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.820000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.820000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
Wed Oct 1 12:01:17 2014 kern.info kernel: [ 25.840000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Bridge 'br-lan' link is up
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'lan' has link connectivity
Wed Oct 1 12:01:17 2014 daemon.notice netifd: wan (1056): udhcpc (v1.22.1) started
Wed Oct 1 12:01:17 2014 daemon.notice netifd: wan (1056): Sending discover...
Wed Oct 1 12:01:17 2014 daemon.notice netifd: wan (1056): Sending select for 192.168.1.3...
Wed Oct 1 12:01:17 2014 daemon.notice netifd: wan (1056): Lease of 192.168.1.3 obtained, lease time 268435455
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan6' is enabled
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Network alias 'eth0.2' link is up
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan6' has link connectivity
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan6' is setting up now
Wed Oct 1 12:01:17 2014 daemon.notice netifd: Interface 'wan' is now up
Wed Oct 1 12:01:17 2014 daemon.notice odhcp6c[1070]: (re)starting transaction on eth0.2
Wed Oct 1 12:01:17 2014 daemon.notice odhcp6c[1070]: Starting SOLICIT transaction (timeout 4294967295s, max rc 0)
Wed Oct 1 12:01:19 2014 kern.info kernel: [ 27.810000] br-lan: port 1(eth0.1) entered forwarding state
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: started, version 2.71 cachesize 150
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq-dhcp[1087]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: using local addresses only for domain lan
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: reading /tmp/resolv.conf.auto
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: using local addresses only for domain lan
Wed Oct 1 12:01:20 2014 daemon.warn dnsmasq[1087]: ignoring nameserver 192.168.1.1 - local interface
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: read /etc/hosts - 1 addresses
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq[1087]: read /tmp/hosts/dhcp - 1 addresses
Wed Oct 1 12:01:20 2014 daemon.info dnsmasq-dhcp[1087]: read /etc/ethers - 0 addresses
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1087]: exiting on receipt of SIGTERM
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: started, version 2.71 cachesize 150
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq-dhcp[1141]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: using local addresses only for domain lan
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: reading /tmp/resolv.conf.auto
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: using local addresses only for domain lan
Wed Oct 1 12:01:21 2014 daemon.warn dnsmasq[1141]: ignoring nameserver 192.168.1.1 - local interface
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: read /etc/hosts - 1 addresses
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq[1141]: read /tmp/hosts/dhcp - 1 addresses
Wed Oct 1 12:01:21 2014 daemon.info dnsmasq-dhcp[1141]: read /etc/ethers - 0 addresses
Wed Oct 1 12:01:21 2014 user.notice firewall: Reloading firewall due to ifup of wan (eth0.2)
Wed Oct 1 12:01:25 2014 daemon.info dnsmasq-dhcp[1141]: DHCPDISCOVER(br-lan) 68:5b:35:d2:b4:1e
Wed Oct 1 12:01:25 2014 daemon.info dnsmasq-dhcp[1141]: DHCPOFFER(br-lan) 192.168.1.102 68:5b:35:d2:b4:1e
Wed Oct 1 12:01:26 2014 daemon.info dnsmasq-dhcp[1141]: DHCPREQUEST(br-lan) 192.168.1.102 68:5b:35:d2:b4:1e
Wed Oct 1 12:01:26 2014 daemon.info dnsmasq-dhcp[1141]: DHCPACK(br-lan) 192.168.1.102 68:5b:35:d2:b4:1e Ivans-MBP-2
And here's dmesg output after booting without the stick inserted:
[ 0.000000] Linux version 3.10.49 (bb@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42625) ) #3 Wed Oct 1 14:00:51 CEST 2014
[ 0.000000] MyLoader: sysp=84c31530, boardp=0065cbe4, parts=195ef6a4
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 80334b60, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126052k/131072k available (2369k kernel code, 5020k reserved, 621k data, 272k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.330000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.330000] pci 0000:00:00.0: [168c:0033] type 00 class 0x028000
[ 0.330000] pci 0000:00:00.0: invalid calibration data
[ 0.340000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.340000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.340000] pci 0000:00:00.0: supports D1
[ 0.340000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.340000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 0.340000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.350000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.350000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.370000] TCP: reno registered
[ 0.370000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.380000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.390000] PCI: CLS 0 bytes, default 32
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.410000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 246
[ 0.430000] io scheduler noop registered
[ 0.430000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.470000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.470000] console [ttyS0] enabled, bootconsole disabled
[ 0.490000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.500000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.510000] 5 tp-link partitions found on MTD device spi0.0
[ 0.510000] Creating 5 MTD partitions on "spi0.0":
[ 0.520000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.520000] 0x000000020000-0x00000012e5fc : "kernel"
[ 0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] 0x00000012e5fc-0x0000007f0000 : "rootfs"
[ 0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.560000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.570000] 0x000000350000-0x0000007f0000 : "rootfs_data"
[ 0.580000] 0x0000007f0000-0x000000800000 : "art"
[ 0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.620000] switch0: Atheros AR8327 rev. 4 switch registered on ag71xx-mdio.0
[ 1.840000] libphy: ag71xx_mdio: probed
[ 2.390000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[ 2.400000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 2.410000] TCP: cubic registered
[ 2.410000] NET: Registered protocol family 17
[ 2.420000] Bridge firewalling registered
[ 2.420000] 8021q: 802.1Q VLAN Support v1.8
[ 2.440000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.440000] Freeing unused kernel memory: 272K (8034c000 - 80390000)
[ 4.620000] usbcore: registered new interface driver usbfs
[ 4.630000] usbcore: registered new interface driver hub
[ 4.630000] usbcore: registered new device driver usb
[ 4.640000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.650000] ehci-platform: EHCI generic platform driver
[ 4.660000] ehci-platform ehci-platform: EHCI Host Controller
[ 4.660000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 4.670000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 4.700000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 4.700000] hub 1-0:1.0: USB hub found
[ 4.710000] hub 1-0:1.0: 1 port detected
[ 5.030000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 5.180000] hub 1-1:1.0: USB hub found
[ 5.180000] hub 1-1:1.0: 4 ports detected
[ 5.470000] usb 1-1.2: new high-speed USB device number 3 using ehci-platform
[ 6.410000] eth0: link up (1000Mbps/Full duplex)
[ 8.360000] jffs2: notice: (373) jffs2_build_xattr_subsystem: complete building xattr subsystem, 21 of xdatum (1 unchecked, 20 orphan) and 34 of xref (0 dead, 20 orphan) found.
[ 9.020000] SCSI subsystem initialized
[ 9.040000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 9.040000] scsi0 : usb-storage 1-1.2:1.0
[ 9.050000] usbcore: registered new interface driver usb-storage
[ 10.050000] scsi 0:0:0:0: Direct-Access LG USB Drive 1100 PQ: 0 ANSI: 0 CCS
[ 10.060000] sd 0:0:0:0: [sda] 7864320 512-byte logical blocks: (4.02 GB/3.75 GiB)
[ 10.070000] sd 0:0:0:0: [sda] Write Protect is off
[ 10.070000] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 10.070000] sd 0:0:0:0: [sda] No Caching mode page found
[ 10.080000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 10.090000] sd 0:0:0:0: [sda] No Caching mode page found
[ 10.090000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 10.150000] sda: sda1 sda2
[ 10.160000] sd 0:0:0:0: [sda] No Caching mode page found
[ 10.160000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 10.170000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 14.400000] EXT4-fs (sda1): recovery complete
[ 14.410000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 14.440000] eth0: link down
[ 17.080000] NET: Registered protocol family 10
[ 17.090000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 17.100000] tun: Universal TUN/TAP device driver, 1.6
[ 17.110000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 17.120000] nf_conntrack version 0.5.0 (1973 buckets, 7892 max)
[ 17.140000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 17.150000] fuse init (API version 7.22)
[ 17.160000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 17.170000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 17.180000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 17.220000] xt_time: kernel timezone is -0000
[ 17.250000] cfg80211: Calling CRDA to update world regulatory domain
[ 17.250000] cfg80211: World regulatory domain updated:
[ 17.260000] cfg80211: DFS Master region: unset
[ 17.260000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 17.270000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.280000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.290000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.300000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.300000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 17.310000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 17.320000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 17.330000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 17.380000] PPP generic driver version 2.4.2
[ 17.400000] NET: Registered protocol family 24
[ 17.450000] ath: EEPROM regdomain: 0x0
[ 17.450000] ath: EEPROM indicates default country code should be used
[ 17.450000] ath: doing EEPROM country->regdmn map search
[ 17.450000] ath: country maps to regdmn code: 0x3a
[ 17.450000] ath: Country alpha2 being used: US
[ 17.450000] ath: Regpair used: 0x3a
[ 17.460000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 17.480000] cfg80211: Calling CRDA for country: US
[ 17.480000] cfg80211: Regulatory domain changed to country: US
[ 17.490000] cfg80211: DFS Master region: FCC
[ 17.500000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 17.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 17.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 17.520000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 17.530000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 17.540000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 17.550000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 17.550000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 17.560000] ath: EEPROM regdomain: 0x0
[ 17.560000] ath: EEPROM indicates default country code should be used
[ 17.560000] ath: doing EEPROM country->regdmn map search
[ 17.560000] ath: country maps to regdmn code: 0x3a
[ 17.560000] ath: Country alpha2 being used: US
[ 17.560000] ath: Regpair used: 0x3a
[ 17.580000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 17.590000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 25.690000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.710000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 25.710000] device eth0.1 entered promiscuous mode
[ 25.720000] device eth0 entered promiscuous mode
[ 25.730000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 25.740000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 25.750000] eth0: link up (1000Mbps/Full duplex)
[ 25.780000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 25.830000] br-lan: port 1(eth0.1) entered forwarding state
[ 25.840000] br-lan: port 1(eth0.1) entered forwarding state
[ 25.840000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 25.850000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 25.910000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 27.840000] br-lan: port 1(eth0.1) entered forwarding state
[ 28.360000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 28.380000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 28.400000] device wlan0 entered promiscuous mode
[ 28.410000] device wlan1 entered promiscuous mode
[ 28.410000] br-lan: port 3(wlan1) entered forwarding state
[ 28.420000] br-lan: port 3(wlan1) entered forwarding state
[ 29.530000] br-lan: port 3(wlan1) entered disabled state
[ 29.550000] br-lan: port 2(wlan0) entered forwarding state
[ 29.560000] br-lan: port 2(wlan0) entered forwarding state
[ 29.570000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 29.610000] br-lan: port 3(wlan1) entered forwarding state
[ 29.610000] br-lan: port 3(wlan1) entered forwarding state
[ 29.620000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 31.560000] br-lan: port 2(wlan0) entered forwarding state
[ 31.610000] br-lan: port 3(wlan1) entered forwarding state
Here's df output without the USB stick inserted:
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 499656 142288 320672 31% /
/dev/root 2304 2304 0 100% /rom
tmpfs 63160 404 62756 1% /tmp
/dev/sda1 499656 142288 320672 31% /overlay
overlayfs:/overlay 499656 142288 320672 31% /
tmpfs 512 0 512 0% /dev
Any help would be greatly appreciated!
(Last edited by el_commandante on 1 Jul 2015, 00:30)