More progress. I've booted the AP135-020 initramfs image. Network and Wireless gets detected.
[ 0.000000] Linux version 3.10.49 (erwin@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45951) ) #6 Sat Jun 27 19:34:37 CEST 2015
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9342 rev 1
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=AP135-020 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art)ro,16000k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 59288k/65536k available (2239k kernel code, 6248k reserved, 603k data, 2212k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] MIPS: machine is Atheros AP135-020 reference board
[ 0.300000] ar71xx: invalid PHY interface mode for GE1
[ 0.310000] registering PCI controller with io_map_base unset
[ 0.320000] bio: create slab <bio-0> at 0
[ 0.330000] PCI host bridge to bus 0000:00
[ 0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 0.350000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.360000] Switching to clocksource MIPS
[ 0.370000] NET: Registered protocol family 2
[ 0.370000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.370000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.380000] TCP: Hash tables configured (established 512 bind 512)
[ 0.380000] TCP: reno registered
[ 0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 3.040000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.050000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 3.060000] msgmni has been set to 115
[ 3.060000] io scheduler noop registered
[ 3.070000] io scheduler deadline registered (default)
[ 3.070000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 3.100000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 3.110000] console [ttyS0] enabled, bootconsole disabled
[ 3.110000] console [ttyS0] enabled, bootconsole disabled
[ 3.120000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 3.130000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 3.130000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 3.140000] mtd: spi0.0: partitioning exceeds flash size, truncating
[ 3.150000] mtd: spi0.0: partitioning exceeds flash size, truncating
[ 3.150000] mtd: spi0.0: skipping zero sized partition
[ 3.160000] mtd: spi0.0: partitioning exceeds flash size, truncating
[ 3.160000] mtd: spi0.0: skipping zero sized partition
[ 3.170000] mtd: spi0.0: partitioning exceeds flash size, truncating
[ 3.180000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 3.180000] Creating 4 MTD partitions on "spi0.0":
[ 3.190000] 0x000000000000-0x000000040000 : "u-boot"
[ 3.190000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 3.200000] 0x000000050000-0x000000800000 : "rootfs"
[ 3.210000] mtd: device 2 (rootfs) set to be root filesystem
[ 3.210000] mtdsplit: no squashfs found in "rootfs"
[ 3.220000] mtdsplit: no squashfs found in "spi0.0"
[ 3.230000] 0x000000050000-0x000000800000 : "firmware"
[ 3.260000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[ 4.460000] libphy: ag71xx_mdio: probed
[ 5.010000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[ 5.030000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 5.040000] TCP: cubic registered
[ 5.040000] NET: Registered protocol family 17
[ 5.040000] 8021q: 802.1Q VLAN Support v1.8
[ 5.060000] Freeing unused kernel memory: 2212K (80327000 - 80550000)
procd: Console is alive
procd: - watchdog -
[ 5.110000] usbcore: registered new interface driver usbfs
[ 5.110000] usbcore: registered new interface driver hub
[ 5.120000] usbcore: registered new device driver usb
[ 5.130000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.140000] ehci-platform: EHCI generic platform driver
[ 5.140000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.150000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.160000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.190000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.190000] hub 1-0:1.0: USB hub found
[ 5.200000] hub 1-0:1.0: 1 port detected
[ 5.200000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 9.690000] NET: Registered protocol family 10
[ 9.700000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[ 9.710000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.730000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 9.740000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 9.770000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.770000] cfg80211: World regulatory domain updated:
[ 9.780000] cfg80211: DFS Master region: unset
[ 9.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.790000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.800000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.810000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.820000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.830000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.830000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 9.840000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 9.850000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 9.930000] ath10k_pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[ 9.940000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.250000] ath10k: pci irq legacy irq_mode 0 reset_mode 0
[ 10.340000] ath10k: otp stream is empty, using board.bin contents
[ 11.170000] ath10k: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.1.467.2-1 api 2 htt 2.1
[ 11.710000] cfg80211: Calling CRDA for country: US
[ 11.720000] cfg80211: Regulatory domain changed to country: US
[ 11.720000] cfg80211: DFS Master region: FCC
[ 11.730000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 11.740000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.740000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 11.750000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 11.760000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 11.770000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 11.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.880000] xt_time: kernel timezone is -0000
[ 11.910000] PPP generic driver version 2.4.2
[ 11.940000] NET: Registered protocol family 24
[ 11.980000] ieee80211 phy1: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
procd: - init complete -
[ 19.500000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 21.010000] eth0: link up (1000Mbps/Full duplex)
[ 21.030000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
BusyBox v1.22.1 (2015-06-26 11:59:06 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Barrier Breaker, r45951)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#
Next step is to create the profile for this device.