OpenWrt Forum Archive

Topic: Micronet SP916GN

The content of this topic has been archived on 2 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hi,

I have a Micronet SP916GN, and I'd like to know if it could support openwrt.

I wonder why there's no any Micronet devices in the list of supported hardware. I've also googled in this forums and couldn't find much info about this routers.

Does anybody tryed with this Micronet? I didn't open it to see what hardware it has inside. Thanks!

micronet SP916GN v3
chipset RT3052F

T101044 MX
29LV3200VTI

Zentel
A3V64S4DETT

U-Boot 1.1.3 (Nov 25 2008 - 16:46:30)


Board: Ralink APSoC DRAM:  relocate_code Pointer at: 80fa8000
flash_protect ON: from 0xBFC00000 to 0xBFC26213

protect on 0

protect on 1

protect on 2

protect on 3

protect on 4

protect on 5

protect on 6

protect on 7

protect on 8

protect on 9

flash_protect ON: from 0xBFC30000 to 0xBFC3FFFF

protect on 10

============================================

Ralink UBoot Version: 3.1

--------------------------------------------

ASIC 3052_MP1 (MAC to GigaMAC Mode)
DRAM COMPONENT: 64Mbits
DRAM BUS: 32BIT
Total memory: 16 MBytes
Flash: 4 MBytes
Date:Nov 25

Please choose the operation:

   0: Load ucos code to SDRAM via TFTP Client.
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line iEth0 (10/100-M)

enetvar=ethaddr,Eth addr:00:AA:BB:CC:DD:18

00:AA:BB:CC:DD:18:


eth_current->name = Eth0 (10/100-M)

DEBUG BootType=48
 

0: System Load Boot Loader | F/W  then write to Flash via TFTP Client.

Warning!! Erase Linux in Flash th*NexTxPacket = 80fe6440
NetTxPacket = 0x80FE6440
NetRxPackets[0] = 0x80FE6A40
NetRxPackets[1] = 0x80FE7040
NetRxPackets[2] = 0x80FE7640
NetRxPackets[3] = 0x80FE7C40
NetRxPackets[4] = 0x80FE8240
NetRxPackets[5] = 0x80FE8840
0FEB840
NetRxPackets[14] = 0x80FEBE40
NetRxPackets[15] = 0x80FEC440
NetRxPackets[16] = 0x80FECA40
NetRxPackets[17] = 0x80FED040
NetRxPackets[18] = 0x80FED640
NetRxPackets[19] = 0x80FEDC40
KSEG1ADDR(NetTxPacket) = 0xA0FE6440

NetLoop,call eth_init !

Trying Eth0 (10/100-M)

Waitting RT2880_RX_DMA_BUSY status Start... done

Mac to giga Mac mode 

Header Payload scatter function is Disable !!

RT2880_PDMA_GLO_CFG=00000020
*************************************************
RT2880_RX_CALC_IDX0=19
RT2880_RX_DRX_IDX0 = 0
*************************************************

Select server or client model: 1/2
server model start
SERVER IP address : 192.168.1.6 port:69
Load address: 0x80100000
Loading: *\0x08

The discussion might have continued from here.