OpenWrt Forum Archive

Topic: Openwrt support for Huawei HG655b

The content of this topic has been archived between 12 Mar 2018 and 5 May 2018. Unfortunately there are posts – most likely complete pages – missing.

danitool wrote:
fratzicu wrote:

Hi,
It's nice to see you guys are still working on this device. What usb jtag cable and software do you reccommend for the flashing? I didn't do this until now, but I would like to learn how to do it.

If you have a parallel port, i recommend a WIGGLER buffered cable, a custom made clone, since the original is too expensive. You can also use an unbuffered cable, the typical DLC5 for hairydairymaid, but you are limited to lenghts less than 15 cm. These cables are totally compatible with any software.

If you don't have a parallel port, well, the Altera USB blaster clone is ok, but some utilities didn't add support for it. This cable is fantastic and cheap, you can even flash SPI memories. But as I said it lacks support in some popular debricking utilities.

It's also possible to use a raspberry pi, there is somewhere in internet a ported Tjtag to rpi. It might be also possible to use another router as a JTAG adapter, but I guess nobody made any attempt in this way.

Is this good? http://www.diygadget.com/tiao-usb-multi … erial.html

andoru wrote:
cornelus2009 wrote:

Solved with a infrared reflow on wifi chip, now wifi is ok.

Where does one do that? Also how does "infrared reflow" translate into romanian? tongue

Hi,
I took the device that had the wifi not working to a guy that repairs such things to verify if it's a hardware issue (fried chip, etc). I wait for his diagnosis. I'll keep you posted.

fratzicu wrote:

Hi,
I took the device that had the wifi not working to a guy that repairs such things to verify if it's a hardware issue (fried chip, etc). I wait for his diagnosis. I'll keep you posted.

Thanks, looking forward to what you find out smile

Hi,
I compiled from danitool's branch a good firmware with needed software to make the hg655b a real nas (ftp, samba) and media server (minidlna) and also a openvpn client and others. It can be found here
https://app.box.com/s/ype4lnjw3t88s21dmi1wbf9vfa7ibx8n
regards

Hi guys.Does anybody know why I still have the following error
[   11.480000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'rt2x00.eeprom'.
[   11.604000] ieee80211 phy0: rt2800_probe_rt: Error - Invalid RT chipset 0xffff, rev ffff detected
[   11.612000] ieee80211 phy0: rt2x00lib_probe_dev: Error - Failed to allocate device
,despite I wrote calibration_data.bin several times?When I make backup,it appears to be ok,it looks exactly like that,Fratzicu posted in the previous pages.I've tried another versions of openwrt but i gave the same results.All partition looks ok,but when I launch "cat /proc/mtd4 |hexdump",it says no file or directory.What could it be?

*

cat /dev/mtd4 |hexdump

Thank you Danitool.Checked again,and this time it show me the calibration data.It is ok,but I still receive that errors.

(Last edited by moreanu_26 on 6 Mar 2015, 13:54)

Hello. I have a router HG655b (fw.18) from romtelecom
I tried the procedure to access the update page but fail ... (hold down the RESET button and then put the power after 10 seconds release the RESET button) .... one LED is on (LAN) which is connected cable network. What am I doing wrong?

mihai.maco wrote:

Hello. I have a router HG655b (fw.18) from romtelecom
I tried the procedure to access the update page but fail ... (hold down the RESET button and then put the power after 10 seconds release the RESET button) .... one LED is on (LAN) which is connected cable network. What am I doing wrong?

Did you set a static IP on your computer compatible with 192.168.1.1?
i.e 192.168.1.100

Yes my ip is 192.168.1.5...

I connected the serial port to HG655b and receive this information:
OY▒'-#5▒▒VV+-▒[595-57▒S_AgmcuAuSmwAgmcuAmcmWAye_▒55#▒▒-▒▒▒▒▒▒▒Ygmy▒▒s!#7▒55#▒▒u5▒▒▒▒u5#▒55#m7▒▒▒▒▒▒▒▒▒▒K▒

mihai.maco wrote:

I connected the serial port to HG655b and receive this information:
OY▒'-#5▒▒VV+-▒[595-57▒S_AgmcuAuSmwAgmcuAmcmWAye_▒55#▒▒-▒▒▒▒▒▒▒Ygmy▒▒s!#7▒55#▒▒u5▒▒▒▒u5#▒55#m7▒▒▒▒▒▒▒▒▒▒K▒

Use the correct baud rate
115200

And don't connect the serial port directly to the rs232 port at the computer, use a serial TTL (3.3V) adapter.

I connected with serial TTL (3.3V) adapter. I entered this mode :
CFE>
I can not access 192.168.1.1 in your browser ....
This information appears when I start the router with serial:

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Fri Apr 16 15:18:13 CST 2010 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB
CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Boot Address 0xb8000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6)                    : HW65x
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:10:18:01:00:01
PSI Size (1-64) KBytes            : 64
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (2 seconds) ***
Auto run second count down: 0
Decompression OK!
Entry at 0x80294000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80294000
Linux version 2.6.21.5 (dongpeiying@IBM_x3500) (gcc version 4.2.3) #567 Thu Sep 1 17:40:41 CST 2011
Pri Table Addr = 0040
ulBootFlag = 0002
Flash 0 at 0xb8000000
  Size : 8 MB
  Regions : 2
    0 : 0x00000000 - 0x00002000 *  8
    1 : 0x00010000 - 0x00010000 * 127
CPU revision is: 0002a031
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
On node 0 totalpages: 16128
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists.  Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 256 (order: 8, 1024 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 59484k/64512k available (2081k kernel code, 5012k reserved, 490k data, 104k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
Calibrating delay loop... 398.33 BogoMIPS (lpj=199168)
Mount-cache hash table entries: 512
wait instruction: enabled
bhal: bhalInit entry
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 128 (order: -3, 512 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IMQ starting with 3 devices...
IMQ driver loaded successfully.
        Hooking IMQ before NAT on PREROUTING.
        Hooking IMQ after NAT on POSTROUTING.

==boot from main kernel==
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xb8020100,5062656]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
MoniterInit entry
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Sep  1 2011 17:39:10
GACT probability on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
Netfilter messages via NETLINK v0.30.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 104k freed
init started: BusyBox vv1.9.1 (2011-09-01 17:42:00 CST)
starting pid 104, tty '': '/etc/init.d/rcS'
RCS DONE
starting pid 106, tty '': '/bin/sh'


BusyBox vv1.9.1 (2011-09-01 17:42:00 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

-/bin/sh: atserver: not found
-/bin/sh: usbdiagd: not found
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache  Char Driver v2.2 Aug  6 2010 11:03:27 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.2 Aug  6 2010 11:03:26
Broadcom Packet CMF (Experimental) Char Driver v0.1 Jul 23 2010 17:43:15 Registered<232>
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jul 23 2010 17:43:15 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
KLOB extended to 7 pools
KLOB extended to 8 pools
Broadcom Packet CMF (Experimental) SWC RESET.
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 23 2010 17:43:16 Registered
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jul 23 2010 17:43:16 Registered
Broadcom Packet CMF (Experimental) ENABLED.
eth0.5: MAC Address: 20:2B:C1:60:D4:E6
eth0.4: MAC Address: 20:2B:C1:60:D4:E6
eth0.3: MAC Address: 20:2B:C1:60:D4:E6
eth0.2: MAC Address: 20:2B:C1:60:D4:E6
DSP Driver: DSP init stub
Endpoint: endpoint_init entry
PROV(ts: 4 s 737ms):ALLOC item = 0000 location = 0x83C96A80 size = 40 line = 0
PROV(ts: 4 s 744ms):ALLOC item = 0001 location = 0x83C96A00 size = 40 line = 0
PROV(ts: 4 s 751ms):ALLOC item = 0002 location = 0x83C96980 size = 40 line = 0
PROV(ts: 4 s 758ms):ALLOC item = 0003 location = 0x83C96900 size = 40 line = 0
PROV(ts: 4 s 765ms):ALLOC item = 0004 location = 0x83C96880 size = 40 line = 0
PROV(ts: 4 s 772ms):ALLOC item = 0005 location = 0x83C96800 size = 40 line = 0
PROV(ts: 4 s 780ms):ALLOC item = 0006 location = 0x83C96780 size = 40 line = 0
PROV(ts: 4 s 787ms):ALLOC item = 0007 location = 0x83C96700 size = 40 line = 0
PROV(ts: 4 s 794ms):ALLOC item = 0008 location = 0x83C96680 size = 40 line = 0
PROV(ts: 4 s 801ms):ALLOC item = 0009 location = 0x83C96600 size = 40 line = 0
PROV(ts: 4 s 808ms):ALLOC item = 0011 location = 0x83CE2600 size = 4 line = 0
PROV(ts: 4 s 815ms):ALLOC item = 0200 location = 0x83C54E80 size = 248 line = 0
PROV(ts: 4 s 823ms):ALLOC item = 0201 location = 0x83C54D80 size = 248 line = 0
PROV(ts: 4 s 830ms):ALLOC item = 0202 location = 0x83C54C80 size = 248 line = 0
PROV(ts: 4 s 837ms):ALLOC item = 0203 location = 0x83C54B80 size = 248 line = 0
PROV(ts: 4 s 844ms):ALLOC item = 0204 location = 0x83C54A80 size = 248 line = 0
PROV(ts: 4 s 852ms):ALLOC item = 0205 location = 0x83C54980 size = 248 line = 0
PROV(ts: 4 s 859ms):ALLOC item = 0206 location = 0x83C54880 size = 248 line = 0
PROV(ts: 4 s 866ms):ALLOC item = 0207 location = 0x83C54780 size = 248 line = 0
PROV(ts: 4 s 873ms):ALLOC item = 0208 location = 0x83C54680 size = 248 line = 0
PROV(ts: 4 s 881ms):ALLOC item = 0209 location = 0x83C54580 size = 248 line = 0
PROV(ts: 4 s 888ms):ALLOC item = 0210 location = 0x83C54480 size = 248 line = 0
PROV(ts: 4 s 895ms):ALLOC item = 0211 location = 0x83C54380 size = 248 line = 0
PROV(ts: 4 s 902ms):ALLOC item = 0212 location = 0x83C54280 size = 248 line = 0
PROV(ts: 4 s 910ms):ALLOC item = 0213 location = 0x83C54180 size = 248 line = 0
PROV(ts: 4 s 917ms):ALLOC item = 0218 location = 0x83C54080 size = 248 line = 0
PROV(ts: 4 s 924ms):ALLOC item = 0219 location = 0x8376FE80 size = 248 line = 0
PROV(ts: 4 s 931ms):ALLOC item = 0220 location = 0x8376FD80 size = 248 line = 0
PROV(ts: 4 s 939ms):ALLOC item = 0221 location = 0x8376FC80 size = 248 line = 0
PROV(ts: 4 s 946ms):ALLOC item = 0222 location = 0x8376FB80 size = 248 line = 0
PROV(ts: 4 s 953ms):ALLOC item = 0223 location = 0x8376FA80 size = 248 line = 0
PROV(ts: 4 s 960ms):ALLOC item = 0224 location = 0x8376F980 size = 248 line = 0
PROV(ts: 4 s 968ms):ALLOC item = 0225 location = 0x8376F880 size = 248 line = 0
PROV(ts: 4 s 975ms):ALLOC item = 0400 location = 0x83CE2580 size = 4 line = 0
PROV(ts: 4 s 982ms):ALLOC item = 0401 location = 0x83CE2500 size = 4 line = 0
PROV(ts: 4 s 989ms):ALLOC item = 0402 location = 0x83CE2480 size = 4 line = 0
PROV(ts: 4 s 996ms):ALLOC item = 0403 location = 0x83CE2400 size = 4 line = 0
PROV(ts: 5 s 3  ms):ALLOC item = 0404 location = 0x83CE2380 size = 4 line = 0
PROV(ts: 5 s 10 ms):ALLOC item = 0405 location = 0x83CE2300 size = 4 line = 0
PROV(ts: 5 s 17 ms):ALLOC item = 0406 location = 0x83CE2280 size = 4 line = 0
PROV(ts: 5 s 25 ms):ALLOC item = 0407 location = 0x83CE2200 size = 4 line = 0
PROV(ts: 5 s 32 ms):ALLOC item = 0408 location = 0x83CE2180 size = 4 line = 0
PROV(ts: 5 s 39 ms):ALLOC item = 0409 location = 0x83CE2100 size = 4 line = 0
PROV(ts: 5 s 46 ms):ALLOC item = 0410 location = 0x83122F80 size = 4 line = 0
PROV(ts: 5 s 53 ms):ALLOC item = 0411 location = 0x83122F00 size = 4 line = 0
PROV(ts: 5 s 60 ms):ALLOC item = 0412 location = 0x83122E80 size = 4 line = 0
PROV(ts: 5 s 67 ms):ALLOC item = 0413 location = 0x83122E00 size = 4 line = 0
PROV(ts: 5 s 74 ms):ALLOC item = 0423 location = 0x83122D80 size = 4 line = 0
PROV(ts: 5 s 81 ms):ALLOC item = 0424 location = 0x83122D00 size = 4 line = 0
PROV(ts: 5 s 88 ms):ALLOC item = 0414 location = 0x83122C80 size = 4 line = 0
PROV(ts: 5 s 95 ms):ALLOC item = 0416 location = 0x83122C00 size = 4 line = 0
PROV(ts: 5 s 102ms):ALLOC item = 0417 location = 0x83122B80 size = 4 line = 0
PROV(ts: 5 s 109ms):ALLOC item = 0418 location = 0x83122B00 size = 4 line = 0
PROV(ts: 5 s 117ms):ALLOC item = 0600 location = 0x83122A80 size = 4 line = 0
PROV(ts: 5 s 124ms):ALLOC item = 0608 location = 0x83122A00 size = 4 line = 0
PROV(ts: 5 s 131ms):ALLOC item = 0609 location = 0x83122980 size = 4 line = 0
PROV(ts: 5 s 138ms):ALLOC item = 0610 location = 0x83122900 size = 4 line = 0
PROV(ts: 5 s 145ms):ALLOC item = 0611 location = 0x83122880 size = 4 line = 0
PROV(ts: 5 s 152ms):ALLOC item = 0612 location = 0x83122800 size = 4 line = 0
PROV(ts: 5 s 159ms):ALLOC item = 0613 location = 0x83122780 size = 4 line = 0
PROV(ts: 5 s 166ms):ALLOC item = 0617 location = 0x83122700 size = 4 line = 0
PROV(ts: 5 s 173ms):ALLOC item = 0618 location = 0x83122680 size = 4 line = 0
PROV(ts: 5 s 180ms):ALLOC item = 0619 location = 0x83122600 size = 4 line = 0
PROV(ts: 5 s 187ms):ALLOC item = 0620 location = 0x83122580 size = 4 line = 0
PROV(ts: 5 s 194ms):ALLOC item = 2000 location = 0x83122500 size = 4 line = 0
PROV(ts: 5 s 202ms):ALLOC item = 0805 location = 0x83122480 size = 4 line = 0
PROV(ts: 5 s 209ms):ALLOC item = 2200 location = 0x83122400 size = 4 line = 0
PROV(ts: 5 s 216ms):ALLOC item = 2201 location = 0x83122380 size = 4 line = 0
PROV(ts: 5 s 223ms):ALLOC item = 2202 location = 0x83122300 size = 4 line = 0
PROV(ts: 5 s 230ms):ALLOC item = 2203 location = 0x83122280 size = 4 line = 0
PROV(ts: 5 s 237ms):ALLOC item = 0616 location = 0x83122200 size = 4 line = 0
PROV(ts: 5 s 244ms):ALLOC item = 2204 location = 0x83122180 size = 4 line = 0
PROV(ts: 5 s 251ms):ALLOC item = 2600 location = 0x83122100 size = 4 line = 0
PROV(ts: 5 s 258ms):ALLOC item = 2601 location = 0x8376EF80 size = 4 line = 0
PROV(ts: 5 s 265ms):ALLOC item = 2602 location = 0x8376EF00 size = 4 line = 0
PROV(ts: 5 s 272ms):ALLOC item = 2603 location = 0x8376EE80 size = 4 line = 0
PROV(ts: 5 s 279ms):ALLOC item = 2604 location = 0x8376EE00 size = 4 line = 0
PROV(ts: 5 s 286ms):ALLOC item = 2605 location = 0x8376ED80 size = 4 line = 0
PROV(ts: 5 s 294ms):ALLOC item = 2606 location = 0x8376ED00 size = 4 line = 0
PROV(ts: 5 s 301ms):ALLOC item = 2800 location = 0x8376EC80 size = 4 line = 0
PROV(ts: 5 s 308ms):ALLOC item = 2801 location = 0x8376EC00 size = 4 line = 0
PROV(ts: 5 s 315ms):ALLOC item = 2802 location = 0x8138BC00 size = 1024 line = 0
PROV(ts: 5 s 322ms):ALLOC item = 2803 location = 0x8376EB80 size = 4 line = 0
PROV(ts: 5 s 329ms):ALLOC item = 0428 location = 0x8376EB00 size = 4 line = 0
PROV(ts: 5 s 336ms):ALLOC item = 0429 location = 0x8376EA80 size = 4 line = 0
PROV(ts: 5 s 343ms):ALLOC item = 0430 location = 0x8376EA00 size = 4 line = 0
PROV(ts: 5 s 350ms):ALLOC item = 0415 location = 0x8376E980 size = 4 line = 0
PROV(ts: 5 s 358ms):ALLOC item = 0427 location = 0x8376E900 size = 4 line = 0
PROV(ts: 5 s 365ms):ALLOC item = 0000 location = 0x83C96580 size = 40 line = 1
PROV(ts: 5 s 372ms):ALLOC item = 0001 location = 0x83C96500 size = 40 line = 1
PROV(ts: 5 s 379ms):ALLOC item = 0002 location = 0x83C96480 size = 40 line = 1
PROV(ts: 5 s 386ms):ALLOC item = 0003 location = 0x83C96400 size = 40 line = 1
PROV(ts: 5 s 393ms):ALLOC item = 0004 location = 0x83C96380 size = 40 line = 1
PROV(ts: 5 s 400ms):ALLOC item = 0005 location = 0x83C96300 size = 40 line = 1
PROV(ts: 5 s 408ms):ALLOC item = 0006 location = 0x83C96280 size = 40 line = 1
PROV(ts: 5 s 415ms):ALLOC item = 0007 location = 0x83C96200 size = 40 line = 1
PROV(ts: 5 s 422ms):ALLOC item = 0008 location = 0x83C96180 size = 40 line = 1
PROV(ts: 5 s 429ms):ALLOC item = 0009 location = 0x83C96100 size = 40 line = 1
PROV(ts: 5 s 436ms):ALLOC item = 0011 location = 0x8376E880 size = 4 line = 1
PROV(ts: 5 s 443ms):ALLOC item = 0200 location = 0x8376F780 size = 248 line = 1
PROV(ts: 5 s 451ms):ALLOC item = 0201 location = 0x8376F680 size = 248 line = 1
PROV(ts: 5 s 458ms):ALLOC item = 0202 location = 0x8376F580 size = 248 line = 1
PROV(ts: 5 s 465ms):ALLOC item = 0203 location = 0x8376F480 size = 248 line = 1
PROV(ts: 5 s 472ms):ALLOC item = 0204 location = 0x8376F380 size = 248 line = 1
PROV(ts: 5 s 480ms):ALLOC item = 0205 location = 0x8376F280 size = 248 line = 1
PROV(ts: 5 s 487ms):ALLOC item = 0206 location = 0x8376F180 size = 248 line = 1
PROV(ts: 5 s 494ms):ALLOC item = 0207 location = 0x8376F080 size = 248 line = 1
PROV(ts: 5 s 501ms):ALLOC item = 0208 location = 0x8376DE80 size = 248 line = 1
PROV(ts: 5 s 509ms):ALLOC item = 0209 location = 0x8376DD80 size = 248 line = 1
PROV(ts: 5 s 516ms):ALLOC item = 0210 location = 0x8376DC80 size = 248 line = 1
PROV(ts: 5 s 523ms):ALLOC item = 0211 location = 0x8376DB80 size = 248 line = 1
PROV(ts: 5 s 530ms):ALLOC item = 0212 location = 0x8376DA80 size = 248 line = 1
PROV(ts: 5 s 538ms):ALLOC item = 0213 location = 0x8376D980 size = 248 line = 1
PROV(ts: 5 s 545ms):ALLOC item = 0218 location = 0x8376D880 size = 248 line = 1
PROV(ts: 5 s 552ms):ALLOC item = 0219 location = 0x8376D780 size = 248 line = 1
PROV(ts: 5 s 559ms):ALLOC item = 0220 location = 0x8376D680 size = 248 line = 1
PROV(ts: 5 s 567ms):ALLOC item = 0221 location = 0x8376D580 size = 248 line = 1
PROV(ts: 5 s 574ms):ALLOC item = 0222 location = 0x8376D480 size = 248 line = 1
PROV(ts: 5 s 581ms):ALLOC item = 0223 location = 0x8376D380 size = 248 line = 1
PROV(ts: 5 s 589ms):ALLOC item = 0224 location = 0x8376D280 size = 248 line = 1
PROV(ts: 5 s 596ms):ALLOC item = 0225 location = 0x8376D180 size = 248 line = 1
PROV(ts: 5 s 603ms):ALLOC item = 0400 location = 0x8376E800 size = 4 line = 1
PROV(ts: 5 s 610ms):ALLOC item = 0401 location = 0x8376E780 size = 4 line = 1
PROV(ts: 5 s 617ms):ALLOC item = 0402 location = 0x8376E700 size = 4 line = 1
PROV(ts: 5 s 624ms):ALLOC item = 0403 location = 0x8376E680 size = 4 line = 1
PROV(ts: 5 s 631ms):ALLOC item = 0404 location = 0x8376E600 size = 4 line = 1
PROV(ts: 5 s 638ms):ALLOC item = 0405 location = 0x8376E580 size = 4 line = 1
PROV(ts: 5 s 645ms):ALLOC item = 0406 location = 0x8376E500 size = 4 line = 1
PROV(ts: 5 s 653ms):ALLOC item = 0407 location = 0x8376E480 size = 4 line = 1
PROV(ts: 5 s 660ms):ALLOC item = 0408 location = 0x8376E400 size = 4 line = 1
PROV(ts: 5 s 667ms):ALLOC item = 0409 location = 0x8376E380 size = 4 line = 1
PROV(ts: 5 s 674ms):ALLOC item = 0410 location = 0x8376E300 size = 4 line = 1
PROV(ts: 5 s 681ms):ALLOC item = 0411 location = 0x8376E280 size = 4 line = 1
PROV(ts: 5 s 688ms):ALLOC item = 0412 location = 0x8376E200 size = 4 line = 1
PROV(ts: 5 s 695ms):ALLOC item = 0413 location = 0x8376E180 size = 4 line = 1
PROV(ts: 5 s 702ms):ALLOC item = 0423 location = 0x8376E100 size = 4 line = 1
PROV(ts: 5 s 709ms):ALLOC item = 0424 location = 0x8376CF80 size = 4 line = 1
PROV(ts: 5 s 716ms):ALLOC item = 0414 location = 0x8376CF00 size = 4 line = 1
PROV(ts: 5 s 723ms):ALLOC item = 0416 location = 0x8376CE80 size = 4 line = 1
PROV(ts: 5 s 730ms):ALLOC item = 0417 location = 0x8376CE00 size = 4 line = 1
PROV(ts: 5 s 738ms):ALLOC item = 0418 location = 0x8376CD80 size = 4 line = 1
PROV(ts: 5 s 745ms):ALLOC item = 0600 location = 0x8376CD00 size = 4 line = 1
PROV(ts: 5 s 752ms):ALLOC item = 0608 location = 0x8376CC80 size = 4 line = 1
PROV(ts: 5 s 759ms):ALLOC item = 0609 location = 0x8376CC00 size = 4 line = 1
PROV(ts: 5 s 766ms):ALLOC item = 0610 location = 0x8376CB80 size = 4 line = 1
PROV(ts: 5 s 773ms):ALLOC item = 0611 location = 0x8376CB00 size = 4 line = 1
PROV(ts: 5 s 780ms):ALLOC item = 0612 location = 0x8376CA80 size = 4 line = 1
PROV(ts: 5 s 787ms):ALLOC item = 0613 location = 0x8376CA00 size = 4 line = 1
PROV(ts: 5 s 794ms):ALLOC item = 0617 location = 0x8376C980 size = 4 line = 1
PROV(ts: 5 s 801ms):ALLOC item = 0618 location = 0x8376C900 size = 4 line = 1
PROV(ts: 5 s 808ms):ALLOC item = 0619 location = 0x8376C880 size = 4 line = 1
PROV(ts: 5 s 815ms):ALLOC item = 0620 location = 0x8376C800 size = 4 line = 1
PROV(ts: 5 s 822ms):ALLOC item = 2000 location = 0x8376C780 size = 4 line = 1
PROV(ts: 5 s 830ms):ALLOC item = 0805 location = 0x8376C700 size = 4 line = 1
PROV(ts: 5 s 837ms):ALLOC item = 2200 location = 0x8376C680 size = 4 line = 1
PROV(ts: 5 s 844ms):ALLOC item = 2201 location = 0x8376C600 size = 4 line = 1
PROV(ts: 5 s 851ms):ALLOC item = 2202 location = 0x8376C580 size = 4 line = 1
PROV(ts: 5 s 858ms):ALLOC item = 2203 location = 0x8376C500 size = 4 line = 1
PROV(ts: 5 s 865ms):ALLOC item = 0616 location = 0x8376C480 size = 4 line = 1
PROV(ts: 5 s 872ms):ALLOC item = 2204 location = 0x8376C400 size = 4 line = 1
PROV(ts: 5 s 879ms):ALLOC item = 2600 location = 0x8376C380 size = 4 line = 1
PROV(ts: 5 s 886ms):ALLOC item = 2601 location = 0x8376C300 size = 4 line = 1
PROV(ts: 5 s 893ms):ALLOC item = 2602 location = 0x8376C280 size = 4 line = 1
PROV(ts: 5 s 900ms):ALLOC item = 2603 location = 0x8376C200 size = 4 line = 1
PROV(ts: 5 s 907ms):ALLOC item = 2604 location = 0x8376C180 size = 4 line = 1
PROV(ts: 5 s 914ms):ALLOC item = 2605 location = 0x8376C100 size = 4 line = 1
PROV(ts: 5 s 922ms):ALLOC item = 2606 location = 0x8376BF80 size = 4 line = 1
PROV(ts: 5 s 929ms):ALLOC item = 2800 location = 0x8376BF00 size = 4 line = 1
PROV(ts: 5 s 936ms):ALLOC item = 2801 location = 0x8376BE80 size = 4 line = 1
PROV(ts: 5 s 943ms):ALLOC item = 2802 location = 0x8138B800 size = 1024 line = 1
PROV(ts: 5 s 950ms):ALLOC item = 2803 location = 0x8376BE00 size = 4 line = 1
PROV(ts: 5 s 957ms):ALLOC item = 0428 location = 0x8376BD80 size = 4 line = 1
PROV(ts: 5 s 964ms):ALLOC item = 0429 location = 0x8376BD00 size = 4 line = 1
PROV(ts: 5 s 971ms):ALLOC item = 0430 location = 0x8376BC80 size = 4 line = 1
PROV(ts: 5 s 978ms):ALLOC item = 0415 location = 0x8376BC00 size = 4 line = 1
PROV(ts: 5 s 986ms):ALLOC item = 0427 location = 0x8376BB80 size = 4 line = 1
PROV(ts: 5 s 993ms):Allocated memory = 14200
Endpoint: endpoint_init COMPLETED
Start mic now ...
load cfm ok.
start log proc...
************************Write flash to db now ..., ulCfgFileType = 0
ifconfig: SIOCSIFNETMASK: Cannot assign requested address
ifconfig: SIOCGIFFLAGS: No such device
wlancmd: wlan driver adapter not found
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
wlancmd: wlan driver adapter not found
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
wlancmd: wlan driver adapter not found
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
wlancmd: wlan driver adapter not found
ifconfig: SIOCGIFFLAGS: No such device
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64


=== pAd = c03b5000, size = 448000 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xb1000000, csr_addr=0xb1000000!
sh: cannot kill pid 320: No such process
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device

begin WlanUpInterfaces...
RX DESC a335f000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
===Ralink RF DATA check ok====
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
RTMPSetPhyMode: channel is out of range, use first channel=0
MCS Set = ff ff 00 00 00
RTMPFilterCalibration - can't find a valid value, loopcnt=102 stop calibratingSYNC - BBP R4 to 20MHz.l
Main bssid = 82:2b:c1:60:d4:e4
<==== rt28xx_init, Status=0
0x1300 = 00064320
@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WEP-D4E6], LEN=[25]
@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WPA-D4E6], LEN=[25]
@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[HideSSID=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[CountryRegion=1], LEN=[16]

wlan_mode set@@@RTPRIV_IOCTL_SET CMD=[WirelessMode=9], LEN=[15]
come in , argv[2] = bgnmixed
@@@RTPRIV_IOCTL_SET CMD=[HtOpMode=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[BasicRate=15], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[FixedTxMode=HT], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[HtGi=0], LEN=[7]
@@@RTPRIV_IOCTL_SET CMD=[HtBw=1], LEN=[7]
@@@RTPRIV_IOCTL_SET CMD=[HtMcs=33], LEN=[9]
@@@RTPRIV_IOCTL_SET CMD=[HtAutoBa=1], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[HtRdg=1], LEN=[8]
@@@RTPRIV_IOCTL_SET CMD=[HtStbc=1], LEN=[9]
@@@RTPRIV_IOCTL_SET CMD=[BGProtection=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[ShortSlot=1], LEN=[12]
@@@RTPRIV_IOCTL_SET CMD=[HtOpMode=0], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[BasicRate=15], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[FixedTxMode=HT], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[RTSThreshold=2347], LEN=[18]
@@@RTPRIV_IOCTL_SET CMD=[FragThreshold=2346], LEN=[19]
@@@RTPRIV_IOCTL_SET CMD=[DtimPeriod=1], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[BeaconPeriod=100], LEN=[17]
@@@RTPRIV_IOCTL_SET CMD=[NoForwarding=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[MaxStaNum=32], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[IgmpSnEnable=1], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[NoForwarding=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[MaxStaNum=32], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[IgmpSnEnable=1], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[WmmCapable=1], LEN=[13]
@@@RTPRIV_IOCTL_SET CMD=[TxBurst=0], LEN=[10]
@@@RTPRIV_IOCTL_SET CMD=[TxPower=95], LEN=[11]
@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14]
@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14]
@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14]
@@@RTPRIV_IOCTL_SET CMD=[ACLClearAll=1], LEN=[14]
@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[AccessPolicy=0], LEN=[15]

begin WlanSetupBridge...
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 2(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0.1) entering forwarding state

begin WlanStartServices...
@@@RTPRIV_IOCTL_SET CMD=[AuthMode=OPEN], LEN=[14]
@@@RTPRIV_IOCTL_SET CMD=[EncrypType=wep], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[IEEE8021X=0], LEN=[12]
@@@RTPRIV_IOCTL_SET CMD=[Key1=525A455A4443324A44354B5950], LEN=[32]
@@@RTPRIV_IOCTL_SET CMD=[DefaultKeyID=1], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[Key2=32323232323232323232323232], LEN=[32]
@@@RTPRIV_IOCTL_SET CMD=[Key3=33333333333333333333333333], LEN=[32]
@@@RTPRIV_IOCTL_SET CMD=[Key4=34343434343434343434343434], LEN=[32]
@@@RTPRIV_IOCTL_SET CMD=[AuthMode=WPA2PSK], LEN=[17]
@@@RTPRIV_IOCTL_SET CMD=[EncrypType=AES], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[IEEE8021X=0], LEN=[12]
@@@RTPRIV_IOCTL_SET CMD=[WPAPSK=Y9SCX6Q575JXE], LEN=[21]
@@@RTPRIV_IOCTL_SET CMD=[DefaultKeyID=1], LEN=[15]
@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WEP-D4E6], LEN=[25]
@@@RTPRIV_IOCTL_SET CMD=[SSID=RomTelecom-WPA-D4E6], LEN=[25]
ATP_WLAN_Init SUCCESS!!
bcmxtmrt: MAC address: 20 2b c1 60 d4 e7
Use default bin /var/cwmp now ...

Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...bcmxtmrt: MAC address: 20 2b c1 60 d4 e8

Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...bcmxtmrt: MAC address: 20 2b c1 60 d4 e9

Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction in disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...
Set Mirror direction out disabled to eth0.2 Successfully...BcmAdsl_Initialize=0xC00AE834, g_pFnNotifyCallback=0xC00D67C4
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 053, PhaseValue = -050, PhaseCntl = 0x3FCB0000
QPROC is aligned, i = 027, PhaseValue = 0050, PhaseCntl = 0x3FCB001A
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
pSdramPHY=0xA3FFFFF8, 0x40444444 0x4C440444
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xBE300 => 0xEBA20 ***
AdslCoreSharedMemInit: shareMemAvailable=83392
AdslCoreHwReset:  AdslOemDataAddr = 0xA3FB3C78
insmod: can't open '/lib/extra/vnet.ko': No such file or directory
device eth0.5 entered promiscuous mode
device eth0.2 entered promiscuous mode
device eth0.3 entered promiscuous mode
device eth0.4 entered promiscuous mode
device eth0 is not a slave of br0
ifconfig: SIOCGIFFLAGS: No such device

ERROR: set wan media error.
atp: cur kernel version:[2.6.21.5]
bridge: can't decode speed from nas_a2_1: 0
device nas_a2_1 entered promiscuous mode
br0: port 7(nas_a2_1) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_a2_1) entering forwarding state
br0: port 7(nas_a2_1) entering disabled state
/var/wan/nas_a3_2/dial: line 1: 3: not found
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:wl0.2
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:wl0.2
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:wl0.3
port_no -1 not surported, br:br0, port:nas_a1_0
port_no -1 not surported, br:br0, port:wl0.3
port_no -1 not surported, br:br0, port:nas_a1_0
Ritchie app, 0
Cannot find device "nas0"
Cannot find device "nas0"
Action 4 device imq0 ifindex 2
Cannot find device "nas0"
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)
iptables: Bad rule (does a matching rule exist in that chain?)

Current sntp process is 1119!
FILE:voicecfg.c,LINE:89,sizeof(TAPI)=884,sizeof(SVC)=31856,sizeof(STATE)=14152
DEBUG[tapi.c:L1252]TAPI_GetCfg
BOS: Enter bosIniBOS: Enter bosInit
t
bosTimerInitEnter bosAppInit

Enter bosAppInExit bosAppInit
it
Exit bosAppBOS: Exit bosInit
Init
BOS: Exitendpoint_open COMPLETED
bosInit
Created message queue "HDSP", depth 40, id 1
00:00:21 CAEnter bosStartApp
LLCLIENT: Initializing endpoints callSipClientMain
Error getting IP address
sipConfig: sipzParamp=0x7f1ffa44 sipzParamp->regname=129.102.100.1
Set Mirror direction in disabled to eth0.2 Successfully...1 line 62 file
Set Mirror direction in disabled to eth0.2 Successfully...hsip.c
sipConfi
Set Mirror direction in disabled to eth0.2 Successfully...g: sipzParamp=0x
Set Mirror direction out disabled to eth0.2 Successfully...7f1ffa44line 72
Set Mirror direction out disabled to eth0.2 Successfully...file  hsip.c
si
Set Mirror direction out disabled to eth0.2 Successfully...pConfig: &mgscb=

bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...

0x51cf74line 85 AppResetDetectionEnable() - Enabled reset detection.
file  hsip.c
00:00:21 CALLCLIENT: Initializing endpoints
00:00:21 Endpoint will be initialized for country ETS (country code = 7)

Endpoint Event task started with pid 1139...
Endpoint Packet task started with pid 1140 ...

Sean@All modules init return 0.
Exit bosStartApp
br0: port 4(eth0.2) entering disabled state
br0: port 5(eth0.3) entering disabled state
br0: port 6(eth0.4) entering disabled state
br0: port 3(eth0.5) entering disabled state
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
bridge br0:9 doesn't exist; can't delete it
Append upnp ssdp listener ok.
Use default bin /var/upnp now ...
BHAL(ts: 22s 621ms):Initializing board HAL...
Codec Support: PCMA/PCMU
Codec Support: G722
Codec Support: G729A
Codec Support: G729B
Codec Support: G723
Codec Support: G726
Codec Support: BV16
Codec Support: BV32
Codec Support: LINPCM128
Codec Support: LINPCM256
Codec Support: ILBC
Codec Support: AMRNB
Codec Support: AMRWB
Codec Support: T.38
PCM: Interrupt Masks
---------------
IrqMask                    = 0x000007070000A0B4
IrqMask1                   = 0x0000000000000000
PCM_IUDMA->ctrl[0].intMask = 0x00000000
PCM_IUDMA->ctrl[1].intMask = 0x00000000

PCM: Interrupt Status
-----------------
IrqStatus                  = 0x0000000000000040
IrqStatus1                 = 0x0000000000000040
PCM_IUDMA->ctrl[0].intStat = 0x00000000
PCM_IUDMA->ctrl[1].intStat = 0x00000000
PCM->pcm_pll_ctrl1         = 0xFC80287D
PCM->pcm_pll_ctrl2         = 0xD0000000
PCM->pcm_pll_ctrl3         = 0x380005C0
PCM->pcm_pll_ctrl4         = 0x00000000
PCM->pcm_int_pending       = 0x00000000
PCM->pcm_int_mask          = 0x00000000
PCM->pcm_ctrl              = 0x00000000
PCM->pcm_chan_ctrl         = 0x00000000
PCM_IUDMA->regs.ctrlConfig = 0x00000001
PCM_IUDMA->ctrl[0].maxBurst                  = 0x00000008
PCM_IUDMA->ctrl[0].config                    = 0x00000000
PCM_IUDMA->stram[0].baseDescPointer          = 0x47D6B476
PCM_IUDMA->stram[0].stateBytesDoneRingOffset = 0x9D4893A1
PCM_IUDMA->stram[0].flagsLengthStatus        = 0xE9352495
PCM_IUDMA->stram[0].currentBufferPointer     = 0x4A462EC4
PCM_IUDMA->ctrl[1].maxBurst                  = 0x00000008
PCM_IUDMA->ctrl[1].config                    = 0x00000000
PCM_IUDMA->stram[1].baseDescPointer          = 0xF546B194
PCM_IUDMA->stram[1].stateBytesDoneRingOffset = 0x07554334
PCM_IUDMA->stram[1].flagsLengthStatus        = 0x0D5EB860
PCM_IUDMA->stram[1].currentBufferPointer     = 0x61795175
PLL init completed. PLL registers set to:
PCM->pcm_pll_ctrl1       = 0x0080147D
PCM->pcm_pll_ctrl2       = 0x10000000
PCM->pcm_pll_ctrl3       = 0x38000700
PCM->pcm_pll_ctrl4       = 0x00000015
Set up PCM registers
XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x80000000

Channel 0 assigned to timeslot 0
XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x89000000

Channel 1 assigned to timeslot 1
XDRV:pcm6368_timeslotAlloc 0xB0004040: 0x89A00000

Channel 2 assigned to timeslot 2
rxDescriptorArea       = 24
txDescriptorArea       = 24
Unaligned dmaRxDesc_c  = 0xA02D7000
Unaligned dmaTxDesc_c  = 0xA02AC000
rxBufferArea          = 1312
txBufferArea          = 1312
Unaligned dmaRxData   = 0xA02AD000
Unaligned dmaTxData   = 0xA02A8000
Aligned Tx Desc (0xA02AC000): chan 0, buf 0, sts 0xe000, len 640, bufp 0x2a8000
Aligned Tx Desc (0xA02AC008): chan 0, buf 1, sts 0x7000, len 640, bufp 0x2a8290
Aligned Rx Desc (0xA02D7000): chan 0, buf 0, sts 0x8000, len 640, bufp 0x2ad000
Aligned Rx Desc (0xA02D7008): chan 0, buf 1, sts 0x9000, len 640, bufp 0x2ad290
initIudma: chan 0, descBase 0xa02d7000, descBaseIudma 0x2d7000
initIudma: chan 1, descBase 0xa02ac000, descBaseIudma 0x2ac000
Enter TaskCreate CMT_EXCEPTION_IST
TaskCreate - spawn new task CMT_EXCEPTION_IST
Enable Got value: 1
NATEnabled Got value: 1

Exit TaskCreate
BHAL(ts: 23s 134ms):DSP build date: Fri_Nov_6_2009_15:10:14

regStatus (reg 12 sel 0)    = 0x10008501
regStatus (reg 12 sel 7)    = 0x00000101
regCause  (reg 13 sel 0)    = 0x00000000
regCause  (reg 13 sel 7)    = 0x00808000
regCMT    (reg 22 sel 0)    = 0xe31e1406
regCMT    (reg 22 sel 1)    = 0x10008001
XDRV:Kicking off secondary thread processor at entry point 0x8108C740 ...

XDRV:Secondary thread processor entry point at 0x8108c740

*** DSP TP: Entered main() ***
XDRV:Thread processor handshake. Secondary app initialized properly.

Enter TaskCreate HTSK
TaskCreate - spawn new task HTSK
Exit TaskCreate
MSPI INITIALIZED
SLIC reset pin: GPIO 32778
SLIC reset pin: GPIO 32778
SLIC chip select pin: GPIO 28
Initializing 89116 device 0 ...
---
SLIC: Starting 89116 device and line initializion...
SLIC: Resetting device using GPIO 32778 ...
SLIC: Reset applied on GPIO pin 32778SLIC: Initializing 89116 device 0
BcmSpiReserveSlave <0,2,6250000>, spiStatus=0
SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event (i = 0)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024
SLIC: 89116 device 0 initialized OK
SLIC: Initializing 89116 FXS line
SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event (i = 0)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048
SLIC: Received VP_EVID_CAL_CMP event (i= 120)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64
SLIC: FXS line RX timeslot = 0
SLIC: FXS line TX timeslot = 0
SLIC: 89116 FXS line initialized OK
SLIC: 89116 device 0 and FXS/FXO initializion COMPLETED OK !
---
Initializing 89316 device 0 ...
---
SLICDAA: Starting 89316 device and line initializion...
SLICDAA: Skipping SLIC chip reset
SLICDAA: Initializing 89316 device 0
SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event (i = 0)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024
SLICDAA: 89316 device 0 initialized OK
SLICDAA: Initializing 89316 FXS line
SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event (i = 0)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048
SLIC: Received VP_EVID_CAL_CMP event (i= 120)
SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64
SLICDAA: FXS line RX timeslot = 2
SLICDAA: FXS line TX timeslot = 2
SLICDAA: 89316 FXS line initialized OK
SLICDAA: Initializing 89316 FXO line
SLICDAA: Locale 7
SLICDAA: Locale 7
SLICDAA: FXO line RX timeslot = 4
SLICDAA: FXO line TX timeslot = 4
SLICDAA: 89316 FXO line initialized OK
SLICDAA: 89316 device 0 and FXS/FXO initializion COMPLETED OK !
---
BHAL(ts: 25s 997ms):COMPLETED Initializing board HAL
boardHalInit completed
Codec Support: PCMA/PCMU
Codec Support: G722
Codec Support: G729A
Codec Support: G729B
Codec Support: G723
Codec Support: G726
Codec Support: BV16
Codec Support: BV32
Codec Support: LINPCM128
Codec Support: LINPCM256
Codec Support: ILBC
Codec Support: AMRNB
Codec Support: AMRWB
Codec Support: T.38
Enter TaskCreate HRTBEAT
TaskCreate - spawn new task HRTBEAT
Exit TaskCreate
HEARTBEAT: Initialized!
Enter TaskCreate VRGEVPR
TaskCreate - spawn new task VRGEVPR
Exit TaskCreate
Enter TaskCreate HCAS
TaskCreate - spawn new task HCAS
Exit TaskCreate
gInterruptCounter     = 0x8115BEF4
gInterruptErrors      = 0x811493F0
gNextRxDesc           = 0x811493E4
gNextTxDesc           = 0x811493E0
32 ms ECAN tail-length
*** gStartRxDesc[0] = 0xA02D7000
*** gBufferSizeBytes = 640
*** gStartTxDesc[0] = 0xA02AC000
hal6368PcmInit 343 nextTxDesc = 0xA02AC000
hal6368PcmInit 343 nextTxDesc = 0xA02AC008
hal6368PcmInit 347 Ownership for TX desc not set. Use this buffer.
DSP: Interrupt Masks
---------------
IrqMask_high               = 0x00000707
IrqMask                    = 0x0000A0B4
IrqMask1_high              = 0x40000000
IrqMask1                   = 0x00000000
PCM_IUDMA->ctrl[0].intMask = 0x00000005
PCM_IUDMA->ctrl[1].intMask = 0x00000005

DSP: Interrupt Status
-----------------
IrqStatus_high             = 0x00000000
IrqStatus                  = 0x00000040
IrqStatus1_high            = 0x00000000
IrqStatus1                 = 0x00000040
PCM_IUDMA->ctrl[0].intStat = 0x00000000
PCM_IUDMA->ctrl[1].intStat = 0x00000000
EPT(ts: 26s 328ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x50) of type: 0x0
EPT(ts: 26s 455ms):Setting T.38 error correction mode for vhd 80 to 0x104
EPT(ts: 26s 791ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x51) of type: 0x0
EPT(ts: 26s 919ms):Setting T.38 error correction mode for vhd 81 to 0x104
EPT(ts: 27s 255ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x52) of type: 0x0
EPT(ts: 27s 382ms):Setting T.38 error correction mode for vhd 82 to 0x104
EPT(ts: 27s 718ms):hdspVhdOpen Secondary Connection VHD success. DSP 0, VHD (0x53) of type: 0x0
EPT(ts: 27s 846ms):Setting T.38 error correction mode for vhd 83 to 0x104
EndpointInit completed

Enter vrgEndptCEPT(ts: 28s 14 ms):endptConfigCIDModeParm classStmType = 2

asTimeParamContrEPT(ts: 28s 21 ms):ENDPT CREATE: Starting initialization for endpt 0
ol... minHookFlaEPT(ts: 28s 29 ms):EPTYPE_FXS
sh = 300, maxHookFlash = 800.
Codec Support: PCMA/PCMU
Codec Support: G722
Codec Support: G729A
Codec Support: G729B
Codec Support: G723
Codec Support: G726
Codec Support: BV16
Codec Support: BV32
Codec Support: LINPCM128
Codec Support: LINPCM256
Codec Support: ILBC
Codec Support: AMRNB
Codec Support: AMRWB
Codec Support: T.38
EPT(ts: 28s 187ms):hdspVhdOpen Line VHD success. DSP 0, VHD (0x54) of type: 0x7
HDSP(ts: 28s 205ms):VHD 0x54: Frame size = 40, Mode = Narrowband
HDSP(ts: 28s 230ms):Switchboard ON (type Duplex): VHD 0x54/1 with VHD 0x0/0
EPT(ts: 28s 237ms):Default value for provItemId '608' did not exist
EPT(ts: 28s 243ms):Default value for provItemId '600' did not exist
SLIC: Mode for FXS channel changed to 1
SLIC: Mode for FXS channel changed to 1
EPT(ts: 28s 292ms):COMPLETED successful initialization for endpt 0
00:00:28 SIGNAL: EPT(ts: 28s 298ms):SIGNAL: ept:0 cnx:-1 s:79 v:0 d:-1 p:-1 r:-1
endpt 0, cnx -1,EPT(ts: 28s 306ms):COMPLETED SIGNAL 79
evt 111 (TxGainEPT(ts: 28s 311ms):SIGNAL: ept:0 cnx:-1 s:80 v:0 d:-1 p:-1 r:-1
), value 0
00:0EPT(ts: 28s 318ms):COMPLETED SIGNAL 80
0:28 SIGNAL: endEPT(ts: 28s 323ms):ENDPT CREATE: Starting initialization for endpt 1
pt 0, cnx -1, evEPT(ts: 28s 331ms):EPTYPE_FXS
t 112 (RxGain), value 0
Codec Support: PCMA/PCMU
Codec Support: G722
Codec Support: G729A
Codec Support: G729B
Codec Support: G723
Codec Support: G726
Codec Support: BV16
Codec Support: BV32
Codec Support: LINPCM128
Codec Support: LINPCM256
Codec Support: ILBC
Codec Support: AMRNB
Codec Support: AMRWB
Codec Support: T.38
EPT(ts: 28s 487ms):hdspVhdOpen Line VHD success. DSP 0, VHD (0x55) of type: 0x7
HDSP(ts: 28s 504ms):VHD 0x55: Frame size = 40, Mode = Narrowband
HDSP(ts: 28s 529ms):Switchboard ON (type Duplex): VHD 0x55/1 with VHD 0x1/0
EPT(ts: 28s 536ms):Default value for provItemId '608' did not exist
EPT(ts: 28s 542ms):Default value for provItemId '600' did not exist
SLICDAA: Mode for FXS channel changed to 1
SLICDAA: Mode for FXS channel changed to 1
EPT(ts: 28s 592ms):COMPLETED successful initialization for endpt 1
00:00:28 SIGNAL: EPT(ts: 28s 599ms):SIGNAL: ept:1 cnx:-1 s:79 v:0 d:-1 p:-1 r:-1
endpt 1, cnx -1,EPT(ts: 28s 606ms):COMPLETED SIGNAL 79
evt 111 (TxGainEPT(ts: 28s 612ms):SIGNAL: ept:1 cnx:-1 s:80 v:0 d:-1 p:-1 r:-1
), value 0
00:0EPT(ts: 28s 619ms):COMPLETED SIGNAL 80
0:28 SIGNAL: endpt 1, cnx -1, evt 112 (RxGain), value 0
RTCP thread started with pid 1191
00:00:28 rtpInit: RTCP task created, taskId = 10251
00:00:28 CALLCLIENT: Initialization complete callSipClientMain

Use default bin /var/console now ...
-------------------------------
-----Welcome to ATP Cli------
-------------------------------

Login:

where wrong in the upgrade procedure?

danitool wrote:
mihai.maco wrote:

I connected the serial port to HG655b and receive this information:
OY▒'-#5▒▒VV+-▒[595-57▒S_AgmcuAuSmwAgmcuAmcmWAye_▒55#▒▒-▒▒▒▒▒▒▒Ygmy▒▒s!#7▒55#▒▒u5▒▒▒▒u5#▒55#m7▒▒▒▒▒▒▒▒▒▒K▒

Use the correct baud rate
115200

And don't connect the serial port directly to the rs232 port at the computer, use a serial TTL (3.3V) adapter.

Hello Danitool! i have a question ! Vorbesti romana?

Your CFE bootloader says:

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Fri Apr 16 15:18:13 CST 2010 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

whereeas the fratzicu's one says

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Wed Mar 23 22:59:09 CST 2011 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

They are different builds, flashing the fratzicu's bootloader should solve the problem. The other option is to build a firmware with a header this particular bootloader understands, but I have no idea how to do it.

danitool wrote:

Your CFE bootloader says:

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Fri Apr 16 15:18:13 CST 2010 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

whereeas the fratzicu's one says

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Wed Mar 23 22:59:09 CST 2011 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

They are different builds, flashing the fratzicu's bootloader should solve the problem. The other option is to build a firmware with a header this particular bootloader understands, but I have no idea how to do it.


Execute any command in CFE appears this message:

CFE> l

*** command status = -1

Any commands that are available?

Thx

try the command

help

if it doesn't work, then this is another CFE crippled by Huawei

danitool wrote:

try the command

help

if it doesn't work, then this is another CFE crippled by Huawei


CFE> help

*** command status = -1

mihai.maco wrote:
danitool wrote:

try the command

help

if it doesn't work, then this is another CFE crippled by Huawei


CFE> help

*** command status = -1

******************************************************************************************************

CFE version 1.0.37-102.6 for BCM96368 (32bit,SP,BE)
Build Date: Fri Apr 16 15:18:13 CST 2010 (lihua@IBM_x3500)
Copyright (C) 2000-2008 Broadcom Corporation.

Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB
CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Boot Address 0xb8000000


Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6)                    : HW65x
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:10:18:01:00:01
PSI Size (1-64) KBytes            : 64
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (2 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>
CFE> help

*** command status = -1
CFE>

Hello Dani,

Sorry for stepping in like this but for sure you and everybody on this topic are more experts then me in routers/modems.

If is possible i will kindly ask your advice

i need to update firmware on more hg655 routers in a short time.

is it possible to connect all the routers to one switch and update all of them at once from computer...
...install the firmware on all at once ??

i have the computer ; the switch ; cables etc ; firmware and no time and unfortunately no knowlage sad to react fast

Sorry for bother and thank you in advance
M

(Last edited by sica2ro200 on 27 Mar 2015, 20:35)

Replacing the OEM firmware by OpenWrt currently requires access to CFE. CFE uses the fixed address 192.168.1.1. Also the router requires pressing the reset button for breaking into CFE, I don't see any way to access all routers at the same time for upgrading. Therefore the short answer is no, you can't.

Of course more ways for upgrading the router might possible without using CFE, but still nobody did any research beyond using CFE. Probably beause CFE is very comfortable for flashing any firmware.

sica2ro200 wrote:

Hello Dani,

Sorry for stepping in like this but for sure you and everybody on this topic are more experts then me in routers/modems.

If is possible i will kindly ask your advice

i need to update firmware on more hg655 routers in a short time.

is it possible to connect all the routers to one switch and update all of them at once from computer...
...install the firmware on all at once ??

i have the computer ; the switch ; cables etc ; firmware and no time and unfortunately no knowlage sad to react fast

Sorry for bother and thank you in advance
M


hello sica2ro200

please help me with the procedure for replacement software hg655b. thx

hello there,

thank you both for reply

@mihai is nothing special...as to any other router....router home page 192.168.1.1/update software/browse for the bin file/next and that's it.

i'm not sure about pressing the reset button but i will check

tnx.....:(it will take longer then expected but if no other way smile

Hi,
I brought back my device from an "electronist" guy. He said that in his opinion there is nothing physically wrong with the wifi chip, meaning it is not fried, I mean that the voltages are right and so on. He doesn't know why the wifi is not recognised by the kernel. He suspects there is something wrong with the CFE.
Maybe there are more series of hg655b that have different CFEs that point to different locations of the calib data? I bought another device. I have a total number of 3 now available. For curiosity, also, I bought a dygadget (tiao) jtag device so I'll play a little bit with it and save everything I can. I hope you will help me, because this is the first time.
Regards

Thanks for keeping us posted fratzicu, hopefully we'll be able to solve our wifi issues smile