Anyone fancy giving a hand?
Working:
Ethernet ports. All seem to be lan.
Leds.
Buttons.
Usb. Well plugging in a device is announced, I havent tested data transfers yet.
Wifi, not fully tested but is emitting a good signal
Not working:
ADSL. Can ping the tc chip at 192.168.2.1 but i need to use extroot to get some additional tools such as nmap to see if i can figure this thing out.
U-Boot 1.1.3 (Jul 7 2012 - 20:00:17)
Board: Ralink APSoC DRAM: 16 MB
relocate_code Pointer at: 80fb0000
Set info->start[0]=BF000000
flash_protect ON: from 0xBF000000 to 0xBF01D423
flash_protect ON: from 0xBF030000 to 0xBF030FFF
============================================
Ralink UBoot Version: 3.3
--------------------------------------------
ASIC 3052_MP2 (Port5<->RvMII)
DRAM component: 128 Mbits SDR
DRAM bus: 16 bit
Total memory: 16 MBytes
Flash component: NOR Flash
Date:Jul 7 2012 Time:20:00:17
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384
##### The CPU freq = 384 MHZ ####
SDRAM bus set to 16 bit
SDRAM size =16 Mbytes
Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
9: Load Boot Loader code then write to Flash via TFTP.
0
3: System Boot system code via Flash.
## Booting image at bf050000 ...
Image Name: MIPS OpenWrt Linux-3.3.8
Created: 2012-07-09 0:00:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 835166 Bytes = 815.6 kB
Load Address: 80000000
Entry Point: 80000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80000000) ...
## Giving linux memsize in MB, 16
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (ant@C2Q) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #5 Mon Jul 9 00:59:06 BST 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001964c (MIPS 24KEc)
[ 0.000000] Ralink RT3052 id:1 rev:3 running at 384.00 MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 01000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00001000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00001000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
[ 0.000000] Kernel command line: board=HG532 console=ttyS1,57600 mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware) rootfstype=sq2
[ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
[ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00046b2d
[ 0.000000] Readback ErrCtl register=00046b2d
[ 0.000000] Memory: 13720k/16384k available (1914k kernel code, 2664k reserved, 317k data, 172k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:48
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.000000] console [ttyS1] enabled, bootconsole disabled
[ 0.010000] Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
[ 0.090000] pid_max: default: 32768 minimum: 301
[ 0.100000] Mount-cache hash table entries: 512
[ 0.110000] NET: Registered protocol family 16
[ 0.120000] MIPS: machine is Hauwei Echolife HG532
[ 0.130000] gpiochip_add: registered GPIOs 0 to 23 on device: RT305X-GPIO0
[ 0.140000] gpiochip_add: registered GPIOs 24 to 39 on device: RT305X-GPIO1
[ 0.150000] gpiochip_add: registered GPIOs 40 to 51 on device: RT305X-GPIO2
[ 0.180000] bio: create slab <bio-0> at 0
[ 0.190000] Switching to clocksource MIPS
[ 0.200000] NET: Registered protocol family 2
[ 0.210000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.230000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.240000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.250000] TCP: Hash tables configured (established 512 bind 512)
[ 0.270000] TCP reno registered
[ 0.270000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.280000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.300000] NET: Registered protocol family 1
[ 0.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.380000] msgmni has been set to 26
[ 0.390000] io scheduler noop registered
[ 0.390000] io scheduler deadline registered (default)
[ 0.410000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.420000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
[ 0.430000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
[ 0.450000] physmap platform flash device: 00800000 at bf000000
[ 0.460000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022a7
[ 0.480000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.490000] Amd/Fujitsu Extended Query version 1.1.
[ 0.510000] physmap-flash.0: Swapping erase regions for top-boot CFI table.
[ 0.520000] number of CFI chips: 1
[ 0.530000] 6 cmdlinepart partitions found on MTD device physmap-flash.0
[ 0.540000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.550000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.560000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.580000] 0x000000040000-0x000000050000 : "factory"
[ 0.590000] 0x000000050000-0x000000130000 : "kernel"
[ 0.610000] 0x000000130000-0x000000400000 : "rootfs"
[ 0.620000] mtd: partition "rootfs" set to be root filesystem
[ 0.630000] mtd: partition "rootfs_data" created automatically, ofs=2F0000, len=110000
[ 0.650000] 0x0000002f0000-0x000000400000 : "rootfs_data"
[ 0.660000] 0x000000050000-0x000000400000 : "firmware"
[ 0.690000] TCP cubic registered
[ 0.700000] NET: Registered protocol family 17
[ 0.710000] 8021q: 802.1Q VLAN Support v1.8
[ 0.720000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.740000] Freeing unused kernel memory: 172k freed
[ 2.430000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 2.510000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 5.970000] JFFS2 notice: (357) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 5 of xref (0 dead, 2 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 6.890000] Compat-wireless backport release: compat-wireless-2012-06-14
[ 6.910000] Backport based on wireless-testing.git master-2012-06-14
[ 6.920000] compat.git: wireless-testing.git
[ 6.960000] cfg80211: Calling CRDA to update world regulatory domain
[ 6.980000] cfg80211: World regulatory domain updated:
[ 6.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 7.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.020000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.040000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 7.050000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.070000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 7.570000] usbcore: registered new interface driver usbfs
[ 7.580000] usbcore: registered new interface driver hub
[ 7.590000] usbcore: registered new device driver usb
[ 7.910000] phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT305X.eeprom'.
[ 8.070000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 2872, rf: 0002, rev: 0200.
[ 8.220000] Error: Driver 'gpio-keys-polled' is already registered, aborting...
[ 8.370000] PPP generic driver version 2.4.2
[ 8.560000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.730000] NET: Registered protocol family 24
[ 8.760000] nf_conntrack version 0.5.0 (217 buckets, 868 max)
[ 9.090000] dwc_otg: version 2.72a 24-JUN-2008
[ 9.100000] dwc_otg: Core Release: 2.66a
[ 9.310000] dwc_otg: Periodic Transfer Interrupt Enhancement - disabled
[ 9.320000] dwc_otg: Multiprocessor Interrupt Enhancement - disabled
[ 9.330000] dwc_otg: Using DMA mode
[ 9.340000] dwc_otg: Device using Buffer DMA mode
[ 9.350000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 9.360000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 9.370000] dwc_otg dwc_otg.0: irq 26, io mem 0x101c0000
[ 9.380000] dwc_otg: Init: Port Power? op_state=1
[ 9.390000] dwc_otg: Init: Power Port (0)
[ 9.400000] hub 1-0:1.0: USB hub found
[ 9.410000] hub 1-0:1.0: 1 port detected
[ 9.800000] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 13.100000] device eth0.1 entered promiscuous mode
[ 13.110000] device eth0 entered promiscuous mode
[ 13.130000] br-lan: port 1(eth0.1) entered forwarding state
[ 13.140000] br-lan: port 1(eth0.1) entered forwarding state
[ 15.140000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.150000] ramips-wdt: timeout value 60 must be 0 < timeout < 33
[ 16.970000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.060000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.070000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.080000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.100000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.110000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.130000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 17.150000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 17.170000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 17.190000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 2, TXop: 0.
[ 17.240000] device wlan0 entered promiscuous mode
[ 17.250000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.290000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.300000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.310000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.330000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.340000] phy0 -> rt2800_is_305x_soc: Notice - Unknown RF chipset on rt305x
[ 17.360000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102.
[ 17.380000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188.
[ 17.400000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0.
[ 17.420000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0.
[ 17.830000] br-lan: port 2(wlan0) entered forwarding state
[ 17.840000] br-lan: port 2(wlan0) entered forwarding state
[ 17.860000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 1, TXop: 47.
[ 17.920000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 1, TXop: 94.
[ 17.960000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 6, Aifs: 3, TXop: 0.
[ 18.030000] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0.
[ 19.840000] br-lan: port 2(wlan0) entered forwarding state
BusyBox v1.19.4 (2012-07-09 00:47:01 BST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
ATTITUDE ADJUSTMENT (Bleeding Edge, r32649)
-----------------------------------------------------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/# cat /proc/cpuinfo
system type : Ralink RT3052 id:1 rev:3
machine : Hauwei Echolife HG532
processor : 0
cpu model : MIPS 24KEc V4.12
BogoMIPS : 255.59
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
ASEs implemented : mips16 dsp
shadow register sets : 1
kscratch registers : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available
(Last edited by routednbooted on 10 Jul 2012, 11:10)