The content of this topic has been archived on 11 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
I apologize for the clumsy English, translated from Russian to English in Google.
Used these Shortcuts http://wiki.openwrt.org/toh/ubiquiti/nanostation, http://wiki.openwrt.org/doc/howto/gener … ng.serial.
How to determine the size of the firmware (eg openwrt-atheros-ubnt2-squashfs.bin size 2,887,680, a calculator get 0x2C1000), how much is this correct?
"erase 0xbf020000 +0 x7c0000". - In Ubiquiti NanoStation Loco2 what address instead 0xbf020000?
Can ustavnka Web interface?
Thank you all.
Aleksandr, use tftp upload.
You need to install OpenWrt image.
Іn paragraph Requirements - NanoStation firmware file from Ubiquiti (not an OpenWrt image)
I understand so OpenWrt so can not be installed.
(http://wiki.openwrt.org/toh/ubiquiti/na … #procedure)
The example sets the openwrt.
tftp 192.168.1.20
tftp> bin
tftp> put openwrt-atheros-ubnt5-squashfs.bin flash_update
Sent 1965199 bytes in 28.8 seconds
tftp> quit
The main purpose of installing openwr, installation tool Aircrack-ng suit me for this openwrt-atheros-ubnt2-squashfs.bin or need to install a different firmware
download image http://downloads.openwrt.org/attitude_a … actory.bin
Turn off the device
Press the reset button
Turn on the device
Release the reset button ~10 seconds (but not longer) after turning the device on. You will know it's ready when the LEDs change.
from command prompt
tftp -i 192.168.1.20 put openwrt-ar71xx-generic-ubnt-nano-m-squashfs-factory.binwait until OpenWRT start working, install aircrack-ng.
(Last edited by neryba on 23 Aug 2013, 13:51)
>tftp -i 192.168.1.20 put openwrt-ar71xx-generic-ubnt-nano-m-squashfs-factory
.bin flash_update
A server error: Invalid firmware file
E:\>tftp -i 192.168.1.20 put openwrt-atheros-ubnt2-squashfs.bin flash_update
The successful transfer: 2883992 байт за 12 сек., 240332 байт/с
Stopped running lights turned off.
Telnet is not to connection, 192.168.1.20, 192.168.1.1
Ping is not 192.168.1.20, 192.168.1.1
Release the reset button ~ 10 seconds (but not longer) after turning the device on. You will know it's ready when the LEDs change.
Ping is not 192.168.1.20, 192.168.1.1
Now running lights red, yellow, green. I did a brick
Telnet 192.168.1.1 booted
Firmware openwrt-atheros-ubnt2-squashfs.bin established
Everything is working. Now you need as you install aircrack-ng.
thank you neryba
openwrt-ar71xx-generic-ubnt-nano-m-squashfs-factory.bin
nano-m and the need to Ubiquiti NanoStation Loco2
Which firmware to try to aircrack-ng.
neryba tell me please: aircrack-ng how to install and configure.
read wiki
http://wiki.openwrt.org/doc/techref/opkg
http://www.aircrack-ng.org/doku.php
i do not know how you mean by "configuring" aircrack...
I read here http://wiki.openwrt.org/oldwiki/wireless.aircrack?s[]=aircrack&s[]=ng
The question is how to set RemoteFileSystem
What do you think would suit NFS
I'd capture on a samba share, seems simpler:
Thank you nebbia88.
I can not combine WAN (WiFi client mode, assigns the address dhcp) and LAN (static address dhсp disabled) interface. That is, in Ubiquiti NanoStation Loco2 intnernet is (downloaded and installed the software from the site http://downloads.openwrt.org/backfire/1 … ackages/).
On your computer, no Internet, the gateway address Ubiquiti Nanostation.
If I understand the need to set up MASQUERADE. http://wiki.openwrt.org/doc/recipes/routedclient # using.masquerade
To install the software on the need to set up Remote FileSystem OPKG
What is WAN IP?
Why you are using backfire? try attitude adjustment it is newer.
The discussion might have continued from here.