3,626

Re: Fully featured OpenWrt build for the WNDR3700

How can I access my modem connected on the wan port?

Thanks.

3,627

Re: Fully featured OpenWrt build for the WNDR3700

vklimk wrote:

Hi guys,
I am using alt build r34054. It works fine for me with default options.
I'd like to implement http-filtering (block access to defined URLs, etc.). I believe it could be transparent proxy or something like that.
Would somebody point me what I should start with? Are there any packages included into alt build which I should use for that?
Thanks in advance guys!

I know it's note the answer you're looking for. But have you tried using OpenDNS? It works ok for blocking certain URLs.

3,628

Re: Fully featured OpenWrt build for the WNDR3700

2 arokh.

could you please compile latest OC build with the settings from r35899 ?
It has more space saved from excluded unrar, nzbget and maybe more.
thank you in advance.

3,629

Re: Fully featured OpenWrt build for the WNDR3700

hwm wrote:
vklimk wrote:

Hi guys,
I am using alt build r34054. It works fine for me with default options.
I'd like to implement http-filtering (block access to defined URLs, etc.). I believe it could be transparent proxy or something like that.
Would somebody point me what I should start with? Are there any packages included into alt build which I should use for that?
Thanks in advance guys!

I know it's note the answer you're looking for. But have you tried using OpenDNS? It works ok for blocking certain URLs.

No, I want to install proxy on my router - it is more powerful and flexible solution I think.
So, would somebody point me what I should start with? Where to get tinyproxy which will work with alt build r34054 for example?

3,630 (edited by axishero 2013-06-09 06:06:52)

Re: Fully featured OpenWrt build for the WNDR3700

Hello,arokh!
Do you mind telling the method of overcloking in openwrt? I want to build a custom image for wndrmac with the stuff I need.

3,631 (edited by hnyman 2013-06-09 08:11:10)

Re: Fully featured OpenWrt build for the WNDR3700

axishero wrote:

Hello,arokh!
Do you mind telling the method of overcloking in openwrt? I want to build a custom image for wndrmac with the stuff I need.

Read discussion from this onward: https://forum.openwrt.org/viewtopic.php?pid=179512#p179512
Especially this: https://forum.openwrt.org/viewtopic.php?pid=179651#p179651

The referenced background material https://forum.openwrt.org/viewtopic.php?id=38777 gives pretty straightforward info and advice to create patch for Linux kernel and to place that patch file at the end of the kernel patch queue. Updated for the current 3.8.13 kernel, the correct place to place the overclock patch is /target/linux/ar71xx/patches-3.8

In Linux 3.8.13 sources, the file to be patched is: https://git.kernel.org/cgit/linux/kerne … gs/v3.8.13

3,632 (edited by axishero 2013-06-09 17:43:01)

Re: Fully featured OpenWrt build for the WNDR3700

hnyman wrote:
axishero wrote:

Hello,arokh!
Do you mind telling the method of overcloking in openwrt? I want to build a custom image for wndrmac with the stuff I need.

Read discussion from this onward: https://forum.openwrt.org/viewtopic.php?pid=179512#p179512
Especially this: https://forum.openwrt.org/viewtopic.php?pid=179651#p179651

You are very kind of help.My overclock is successful!
But I got some strange letters from ttl after overclock.It's a little bit annoying .My ttl cable is CP2102.
Update:Tested with arokh's OC build and another cable with different chip,the same showed up.

U-Boot 1.1.4 (May 27 2011 - 14:58:01)

DNI HW ID: 29763654 flash 16MB RAM 128MB (ar7100) U-boot dni25 V0.1
DRAM:  b8050000: 0xc0140180
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 265k for U-Boot at: 87fbc000
Reserving 192k for malloc() at: 87f8c000
Reserving 44 Bytes for Board Info at: 87f8bfd4
Reserving 36 Bytes for Global Data at: 87f8bfb0
Reserving 128k for boot params() at: 87f6bfb0
Stack Pointer at: 87f6bf98
Now running in RAM - U-Boot at: 87fbc000
id read 0x100000ff
flash size 16MB, sector count = 256
Flash: 16 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7100_enet_initialize...
CHH:mac: 0 if: 2
CHH:mac:verify: 0 if: 00000002
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803788
after rtl8366s_initChip ret=0
eth0: 20:4e:7f:82:9a:59
eth0 up
CHH:mac: 1 if: 1
CHH:mac:verify: 1 if: 00000001
: cfg1 0xf cfg2 0x7014
in rtl8366s_phy_setup mac=-1476803308
eth1: 20:4e:7f:82:9a:5a
eth1 up
eth0, eth1
Trying eth0
: unit 0 phy is up...RGMii 1000Mbps full duplex
#259:ag7100_set_mac_from_link
: pll reg 0x18050010: 0x11110000  
: cfg_1: 0x1ff0000
: cfg_2: 0x3ff
: cfg_3: 0x8001ff
: cfg_4: 0xffff
: cfg_5: 0xfffef
: done cfg2 0x7215 ifctl 0x40605060 miictrl 0x22 

 Client starts...[Listening] for ADVERTISE...checksum bad
checksum bad
Tchecksum bad
Tchecksum bad
checksum bad
Tchecksum bad

Retry count exceeded; boot the image as usual

 nmrp server is stopped or failed !
Hit any key to stop autoboot:  0 
   Verifying Checksum ... OK
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 934184 bytes loaded to 0x80800000
## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.3.8
   Created:      2013-06-09  11:12:19 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    934120 Bytes = 912.2 kB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728

Starting kernel ...
./BBB+??+e;.A"1E1i5g8.A7&"3TA:.5gA??F.1?1."$.e7.R.?R&+.9f$j?.    J?BBB+.?7?4-?.=?.E4-.BBB+.)?.5gA5B?"%*A?4A.B+?!.:?!?$?
                                                 JQ..B+.7U;.?:B%?%
                                                                               BB+?(&uBB+??
                      :B%?BBB+.+e5.IQ=V7A4?+?uQ..B+5-we=BBB.BBB?1.Q?BBB+?.KIwi?6
                                         ?.i=6.1.]3?.KIQ..B+?WA(?:.I;?/BBB+ve5,?BBaBB4A.B+?+E4-?WA;+e8?..?*BBB+..A5-we=??wI;4A.B+B<BBB?aBB|/BBB+..??WY5..7WA7.:?TGQ8..?5wA7g?1?*eN%JQ..B+..Y?Y1GA4.u..*?.?4-?.$VB/
                    a1.Q.7.7.?2wi.Q:Gf.?6-2.?7Ke?7e8?$.a<
          B"2.;.??;.1?9.2.M26]5KI?BBB+.??.A1?5.%Jue0.'2R.+e|/BBB+.?=.WA4.+E4-.KQ1kb"7.:RZ?Ti1VU.BBB+?GITE4-??.A1?5.F"7.:NNKbTi1VU.BBB+?.e=?.9.7.WA??!Y.1.?We5?+e4A.B+?.e=.+A3.1NY.1.?!YTE4-..e1.5We5?+e?BBB+?..3.Vi4?.8.BB6BBB+?,JA3.Vi4?.8.BB6.BBB+?.qF+Z?N^.,GA2WARJ..Y?IRぎ?1.0R.*i1JR?..?.1/U.BBB+??(];E;'2?4.y*e6wE6.;'2)e$?*e$$/BBB+?I%)V|/BBB+.E:,.3.qw]8e:.R:
                              .?%A..R4A.B+?觊A<.*i4??Y9.?BZB+?.Y3.1??.A1?5.%J?B^B+??*.?.0??3GA2,Y=F|/B^B+..Q5=1
                u?5.:-
                         ..A?F?..1.??BbB+?u/E4.A5?i     !?H.    *B? ??J.B-?.8.6
                                    ?*.?7GI:?.5?1=2..I8|/J.B-.?3?8-?.TwY1
                  B?J.B-?*?.2VGM1?.BBBQ.?B+?.i;BBB??2.:.9VI?Y?BB6aJM2J9Q.?B+?.i;BBB??2.:.9VIWwA?B+$/J+BB-?.BBB$:.i8..1.gQ3.8..J+BB-?.BBB?.i8..1.gQ3.8..JKBB-?.BBB$:.B.Vw]1
                                      ?-B<$BB6aB2JM-4A?B+?.BBB?.B.Vw]1
               ?-B<$BB6aF2JM-4A?B+?.BBB$:?.A5VA2?8.Q.?B+?.BBB??.A5VA$.?F?JkBB-?.kQ5wA8.7U;?3-?.J
                                                                          BB-??*.e8.0??3GA2,Y=J?J
                               BB-??-+A3.1??.A1?5.$J"7.:BR
                                                                          ?=+e|/J+BB-?..2e4-
                       ??.A1?5.
                                      f"7.:NNKbTi1VU.J+BB-?..A4.+E4-.KQ1f"7.:JFRTi1VU.JKBB-??e4?.e?M5*e1
                                                               "1.2e4-
                                                                        R
                                                                          ?5GAf&$/JKBB-?..A:.e8.04A?B+?..+E4-.KQ1
                                                            ?7.:BR
                                                                       ?=+e4A?B+??.+A4.+E4-.KQ1
                                ?7.:BR
                                           ?=+e|/J.B-??*.e8.0??3GA2,Y=F?J.B-?-e4ju+e;.A.B.R&?4avi3WeQ..B+.h.+e;.A? &"+)V**"$?Q?%+??    !%%?(*"3&JFB?
                                                    ?.%7]?JBB+?.5?..1
     ?J.JFB+??WI9Wew]8?.8.04A.B+??WI9We*A0]1?.8.0"0.i4..JJB+?VYb%>+V..eF]:kY    A;e5wA0.2WI?JRB+?VY?j
     q+1
         ?.B<$BB.'F&?.?V(?    2.850000] console [ttyS0] enabled, bootconsole disabled
[    2.850000] console [ttyS0] enabled, bootconsole disabled
[    2.860000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[    2.870000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[    2.870000] 6 cmdlinepart partitions found on MTD device spi0.0
[    2.880000] Creating 6 MTD partitions on "spi0.0":
[    2.880000] 0x000000000000-0x000000050000 : "u-boot"
[    2.890000] 0x000000050000-0x000000070000 : "u-boot-env"
[    2.890000] 0x000000070000-0x000000160000 : "kernel"
[    2.900000] 0x000000160000-0x000000ff0000 : "rootfs"
[    2.910000] mtd: partition "rootfs" set to be root filesystem
[    2.910000] mtd: partition "rootfs_data" created automatically, ofs=700000, len=8F0000 
[    2.920000] 0x000000700000-0x000000ff0000 : "rootfs_data"
[    2.930000] 0x000000ff0000-0x000001000000 : "art"
[    2.930000] 0x000000070000-0x000000ff0000 : "firmware"
[    2.940000] Realtek RTL8366S ethernet switch driver version 0.2.2
[    2.950000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[    2.950000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[    2.990000] rtl8366s: probed
[    2.990000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    3.300000] eth1: Atheros AG71xx at 0xba000000, irq 5
[    3.600000] ag71xx ag71xx.1: eth1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[    3.610000] TCP cubic registered
[    3.620000] NET: Registered protocol family 17
[    3.620000] 8021q: 802.1Q VLAN Support v1.8
[    3.630000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    3.640000] Freeing unused kernel memory: 212k freed
[    5.030000] eth0: link up (1000Mbps/Full duplex)
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
[    8.320000] eth0: link down
[    9.740000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[    9.750000] Backport based on wireless-testing.git master-2013-02-22
[    9.760000] compat.git: wireless-testing.git
[    9.860000] cfg80211: Calling CRDA to update world regulatory domain
[    9.860000] cfg80211: World regulatory domain updated:

3,633

Re: Fully featured OpenWrt build for the WNDR3700

Put out an updated oc build - r37038 smile

3,634

Re: Fully featured OpenWrt build for the WNDR3700

The last build had some issues with my old crda setup, wouldn't set country. I changed to the new regdb.txt method + CONFIG_ATH_USER_REGD and it seems to work now, build updated as well.

3,635

Re: Fully featured OpenWrt build for the WNDR3700

arokh wrote:

The last build had some issues with my old crda setup, wouldn't set country. I changed to the new regdb.txt method + CONFIG_ATH_USER_REGD and it seems to work now, build updated as well.

Could you update the default version? Because I want use the pptp vpn.
thank you

Re: Fully featured OpenWrt build for the WNDR3700

And is there any possibiilty to build the images ourselves? Do you have the files to do that? (and would you be ready to give it)
(f.e. config files for toolchain, patches,...)

3,637

Re: Fully featured OpenWrt build for the WNDR3700

Dima_2005 wrote:

And is there any possibiilty to build the images ourselves? Do you have the files to do that? (and would you be ready to give it)
(f.e. config files for toolchain, patches,...)

Sure, you can download all sources and packages for free:
https://dev.openwrt.org/wiki/GetSource

His custom configuration file for each build version can be found like in this example:
http://enduser.subsignal.org/~trondah/builds/normal/r34054/openwrt-wndr3700-r34054.config

You can check out the top level folders for other versions or build type.

3,638

Re: Fully featured OpenWrt build for the WNDR3700

I'm using 36195 oc and I saw a weird thing.. While I use same configuration as my old version it seems minidlna is wonky..

How should I say it? Sometimes my TV sees it, sometimes don't. Before I was constantly using minidlna without problem. Is there a problem on minidlna with v36195? Should I upgrade to the latest (37038)?

3,639

Re: Fully featured OpenWrt build for the WNDR3700

Hi all,
I'm new in this forum. I have a wndr3700v1. About one year ago I installed a firmware openwrt for some time. In the end I went back to original firmware because I have no special need for additional features.
Now I need to have a dynamic dns service with No-IP and I think to install the Arokh firmware. I have some questions:
1. Is this the last version? If no where I can find it?
http://enduser.subsignal.org/~trondah/builds/normal/r34054/

2. Where I can find the installation procedure?

3. What are the performance of the wifi compared to those of the original firmware?

4. What are the performance of the CPU?

Thanks

3,640

Re: Fully featured OpenWrt build for the WNDR3700

Hi All,

I've been running r34054 on my WNDR3700v2 for several months now.  Everything works fine, except between about 6-14 days (seems to be random), my 2.4 GHz network stops working.  The SSID for it is still visible, but when any device attempts to connect to it, (i.e. iOS, Android, MacBook Air, MacBook Retina, etc.) it's unable to.

A simple power-cycle fixes it and it's a minor inconvenience, but was wondering if anyone else has experienced that issue?

Thanks in advance!

Cheers,
Kermee

3,641

Re: Fully featured OpenWrt build for the WNDR3700

Hi Arokh,

I see there's a new OC build, but as I'm not into OC'ing I'm looking for a recent standard build.

Should I use the one mentioned by temp302t, r34054 which dates from November 2012, or use this one from July 2nd (this new one is somewhat smaller however):

http://enduser.subsignal.org/~trondah/tree/bin/ar71xx/

What's the difference?

Thanks smile

3,642

Re: Fully featured OpenWrt build for the WNDR3700

zaadstra wrote:

Hi Arokh,

I see there's a new OC build, but as I'm not into OC'ing I'm looking for a recent standard build.

Should I use the one mentioned by temp302t, r34054 which dates from November 2012, or use this one from July 2nd (this new one is somewhat smaller however):

http://enduser.subsignal.org/~trondah/tree/bin/ar71xx/

What's the difference?

Thanks smile

I've done a diff on the package list and see some packages stripped and others updated.

More important question, is this firmware stable or more an internal/"nightly" build?  is it safe wink

Thanks!

3,643

Re: Fully featured OpenWrt build for the WNDR3700

New OC build: http://enduser.subsignal.org/~trondah/dangerous_overclock/r37215/

3,644

Re: Fully featured OpenWrt build for the WNDR3700


Could you update the default version? Because I want use the pptp vpn.
thank you

3,645

Re: Fully featured OpenWrt build for the WNDR3700

kw_openwrt wrote:

I'm very pleased with the OpenWrt Barrier Breaker r34054 release. It's very stable and everything is working as is should be. I don't have enough Linux skills to figure it out by myself, but I want to install a VPN software to make it possible to setup a connection from my PC or Android phone to my router. When I want to watch TV on my phone, I will need a connection to my ISP, which can be done by a VPN connection if I'm not at home.

Can someone help me so setup a VPN server? When I follow this guide http://wiki.openwrt.org/inbox/vpn.howto I get errors when I want to build certificates (build-ca). build-ca: 8: ./pkitool: not found

With other guides I have also some problems because of missing packages.
http://www.mayrhofer.eu.org/l2tp-ipsec-gateway-for-mobile-phones

I believe the IPsec/L2TP is the best way because Android supports that by default.

Hopefully someone has a guide or can explain me how the do this. Thanks.

Me too i am trying to achieve the same VPN for Android (Galaxy S4) to access the USB files connected to the router, somewhat L2TP cannot be installed, will post more info on this later... I am using OpenWRT Barrier Breaker on my D-Link 835 A1.
If anyone knows a better way to use IPSEC, Samba and Android please let us know.

3,646 (edited by mmhorda 2013-07-14 22:04:59)

Re: Fully featured OpenWrt build for the WNDR3700


Hello. 
GRE tunnels are broken on latest build sad

by the way. did have a chance to take a look at miniupnpd? as long as i know it should contain an extra rule in firewall since it was  moved to firewall 3 otherwise it looks like working but not when you take a closer look.

here is the rule:

config include 'miniupnpd'
    option type 'script'
    option path '/usr/share/miniupnpd/firewall.include'
    option family 'IPv4'
    option reload '1'

3,647 (edited by arokh 2013-07-15 17:26:01)

Re: Fully featured OpenWrt build for the WNDR3700

I don't use GRE tunnels, if you have a fix share it and I'll include it. UPNP has been working for me, but I'll include the missing config in next build.

EDIT: I noticed there is a new module ip_tunnel in 3.10 and it was needed by the sit module. I've put up a new oc build with that module can you try now?

3,648

Re: Fully featured OpenWrt build for the WNDR3700

arokh wrote:

I don't use GRE tunnels, if you have a fix share it and I'll include it. UPNP has been working for me, but I'll include the missing config in next build.

EDIT: I noticed there is a new module ip_tunnel in 3.10 and it was needed by the sit module. I've put up a new oc build with that module can you try now?

Thanks a lot.
Yes I will try these days and let you know.

3,649

Re: Fully featured OpenWrt build for the WNDR3700

arokh wrote:

I don't use GRE tunnels, if you have a fix share it and I'll include it. UPNP has been working for me, but I'll include the missing config in next build.

EDIT: I noticed there is a new module ip_tunnel in 3.10 and it was needed by the sit module. I've put up a new oc build with that module can you try now?


Could you update the default version? Because I want use the pptp vpn.
thank you

3,650

Re: Fully featured OpenWrt build for the WNDR3700

gkl1368 wrote:
arokh wrote:

I don't use GRE tunnels, if you have a fix share it and I'll include it. UPNP has been working for me, but I'll include the missing config in next build.

EDIT: I noticed there is a new module ip_tunnel in 3.10 and it was needed by the sit module. I've put up a new oc build with that module can you try now?


Could you update the default version? Because I want use the pptp vpn.
thank you

Second  that.  Or is it an option to build with the optimizations but without the OC, so creating the same firmware but at normal clock speed?  Would it be possible to set the speed from within running firmware with an option or config file?