Re: TP-Link TL-MR3020 Support

Thanks for share.

Re: TP-Link TL-MR3020 Support

Thanks, very much!

Re: TP-Link TL-MR3020 Support

Hi, me again smile.
  Updated with http://downloads.openwrt.org/attitude_a … pgrade.bin firmware, but now i have another issue:
===========
root@OpenWrt:/etc/modules.d# dmesg
[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Nov 18 04:31:55 UTC 2012
[    0.000000] MyLoader: sysp=444ba8b5, boardp=5fbcaeef, parts=ebc66edc
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR9330 rev 1
[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 02000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00002000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00002000
[    0.000000] On node 0 totalpages: 8192
[    0.000000] free_area_init_node: node 0, pgdat 802ef060, node_mem_map 81000000
[    0.000000]   Normal zone: 64 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
[    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 29008k/32768k available (2209k kernel code, 3760k reserved, 412k data, 212k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[    0.100000] MIPS: machine is TP-LINK TL-MR3020
[    0.350000] bio: create slab <bio-0> at 0
[    0.360000] Switching to clocksource MIPS
[    0.360000] NET: Registered protocol family 2
[    0.370000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.370000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.370000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.380000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.390000] TCP reno registered
[    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] NET: Registered protocol family 1
[    0.410000] PCI: CLS 0 bytes, default 32
[    0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.430000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.440000] msgmni has been set to 56
[    0.440000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.450000] io scheduler noop registered
[    0.450000] io scheduler deadline registered (default)
[    0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.470000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[    0.480000] console [ttyATH0] enabled, bootconsole disabled
[    0.490000] m25p80 spi0.0: found s25sl032a, expected m25p80
[    0.500000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
[    0.500000] 5 tp-link partitions found on MTD device spi0.0
[    0.510000] Creating 5 MTD partitions on "spi0.0":
[    0.510000] 0x000000000000-0x000000020000 : "u-boot"
[    0.520000] 0x000000020000-0x000000109894 : "kernel"
[    0.520000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.540000] 0x000000109894-0x0000003f0000 : "rootfs"
[    0.540000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.550000] mtd: partition "rootfs" set to be root filesystem
[    0.560000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=110000
[    0.570000] 0x0000002e0000-0x0000003f0000 : "rootfs_data"
[    0.570000] 0x0000003f0000-0x000000400000 : "art"
[    0.580000] 0x000000020000-0x0000003f0000 : "firmware"
[    0.600000] ag71xx_mdio: probed
[    0.610000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.160000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd041, driver=Generic PHY]
[    1.170000] TCP cubic registered
[    1.170000] NET: Registered protocol family 17
[    1.180000] Bridge firewalling registered
[    1.180000] 8021q: 802.1Q VLAN Support v1.8
[    1.190000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.200000] Freeing unused kernel memory: 212k freed
[    3.090000] Registered led device: tp-link:green:3g
[    3.100000] Registered led device: tp-link:green:wlan
[    3.100000] Registered led device: tp-link:green:lan
[    3.100000] Registered led device: tp-link:green:wps
[    5.160000] eth0: link up (100Mbps/Full duplex)
[    6.420000] JFFS2 notice: (441) jffs2_build_xattr_subsystem: complete building xattr subsystem, 19 of xdatum (1 unchecked, 18 orphan) and 28 of xref (0 dead, 18 orphan) found.
[    6.540000] eth0: link down
[    8.250000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[    8.250000] Backport based on wireless-testing.git master-2012-09-07
[    8.260000] compat.git: wireless-testing.git
[    8.290000] cfg80211: Calling CRDA to update world regulatory domain
[    8.300000] cfg80211: World regulatory domain updated:
[    8.300000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.310000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.320000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.330000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.330000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.340000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.690000] usbcore: registered new interface driver usbfs
[    8.690000] usbcore: registered new interface driver hub
[    8.700000] usbcore: registered new device driver usb
[    9.260000] ath: EEPROM regdomain: 0x0
[    9.260000] ath: EEPROM indicates default country code should be used
[    9.260000] ath: doing EEPROM country->regdmn map search
[    9.260000] ath: country maps to regdmn code: 0x3a
[    9.260000] ath: Country alpha2 being used: US
[    9.260000] ath: Regpair used: 0x3a
[    9.260000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    9.260000] Registered led device: ath9k-phy0
[    9.260000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[    9.270000] cfg80211: Calling CRDA for country: US
[    9.270000] cfg80211: Regulatory domain changed to country: US
[    9.280000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.290000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.290000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    9.300000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.310000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.320000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.320000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    9.370000] PPP generic driver version 2.4.2
[    9.640000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.870000] NET: Registered protocol family 24
[    9.890000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.890000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[    9.900000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    9.940000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    9.960000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    9.960000] hub 1-0:1.0: USB hub found
[    9.960000] hub 1-0:1.0: 1 port detected
[    9.990000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[   10.230000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   10.270000] uhci_hcd: USB Universal Host Controller Interface driver
[   10.290000] usb 1-1: new full-speed USB device number 2 using ehci-platform
[   10.400000] usbcore: registered new interface driver usbserial
[   10.410000] USB Serial support registered for generic
[   10.450000] usbcore: registered new interface driver usbserial_generic
[   10.450000] usbserial: USB Serial Driver core
[   10.510000] USB Serial support registered for GSM modem (1-port)
[   10.510000] option 1-1:1.0: GSM modem (1-port) converter detected
[   10.520000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[   10.530000] option 1-1:1.1: GSM modem (1-port) converter detected
[   10.530000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[   10.540000] option 1-1:1.2: GSM modem (1-port) converter detected
[   10.540000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
[   10.550000] option 1-1:1.3: GSM modem (1-port) converter detected
[   10.560000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
[   10.560000] option 1-1:1.4: GSM modem (1-port) converter detected
[   10.570000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4
[   10.580000] usbcore: registered new interface driver option
[   10.580000] option: v0.7.2:USB Driver for GSM modems
[   13.870000] device eth0 entered promiscuous mode
[   14.370000] eth0: link up (100Mbps/Full duplex)
[   14.370000] br-lan: port 1(eth0) entered forwarding state
[   14.380000] br-lan: port 1(eth0) entered forwarding state
[   16.380000] br-lan: port 1(eth0) entered forwarding state
[   17.390000] device wlan0 entered promiscuous mode
[   18.260000] br-lan: port 2(wlan0) entered forwarding state
[   18.270000] br-lan: port 2(wlan0) entered forwarding state
[   20.270000] br-lan: port 2(wlan0) entered forwarding state
root@OpenWrt:/etc/modules.d# lsusb
/bin/ash: lsusb: not found
root@OpenWrt:/etc/modules.d# opkg install usb-modeswitch-data
Package usb-modeswitch-data (20120120-1) installed in root is up to date.
root@OpenWrt:/etc/modules.d# opkg install luci-proto-3g
Unknown package 'luci-proto-3g'.
Collected errors:
* opkg_install_cmd: Cannot install package luci-proto-3g.
root@OpenWrt:/etc/modules.d#
===========

and in web GUI in the interface properties i see "cannot open /usr/lib/lua/luci/model/cbi/admin_network/proto_3g.lua: No such file or directory" error. Any ideas?

Re: TP-Link TL-MR3020 Support

opkg update

330 (edited by written_direcon 2013-01-05 14:35:29)

Re: TP-Link TL-MR3020 Support

opkg update
opkg install usbutils usb-modeswitch-data luci-proto-3g

And all errors should be fixed :-)

Re: TP-Link TL-MR3020 Support

root@OpenWrt:/# opkg update
Downloading http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/packages/Packages.gz.
Inflating http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/packages/Packages.gz.
Updated list of available packages in /var/opkg-lists/attitude_adjustment.
root@OpenWrt:/# opkg install libusb
Package libusb (0.1.12-3) installed in root is up to date.
root@OpenWrt:/# which lsusb
root@OpenWrt:/# find / -name lsusb

Re: TP-Link TL-MR3020 Support

written_direcon> yes! Works now! Thanks!

Re: TP-Link TL-MR3020 Support

The magic of opkg update! Do it regularly!

334

Re: TP-Link TL-MR3020 Support

Hi folks
I'm new here and maybe I ask dumb questions.

I want to use a MR3020 for wireless communication to a arduino based board via ftdi.
the plan was to use the rx and tx directly and have raw communication with ser2net.
the base stuff is done, but I'm so far away with linux, that I need some help:

is it possible to use the console rx and tx of the 3020 while in uboot, and then get it free to use it with ser2net?

i'm already flashed the uboot with webfailsafe.

some ideas?

thx
Lutz

Re: TP-Link TL-MR3020 Support

https://forum.openwrt.org/viewtopic.php?id=41219

336

Re: TP-Link TL-MR3020 Support

great.
thx for the ultrafast help !

337 (edited by novikorisnik 2013-01-14 00:26:43)

Re: TP-Link TL-MR3020 Support

Hello to all of you good people.

I have to commend, I have succeeded to make WiFi internet radio with TP Link MR3020. Maybe it is not big deal for you guys, but for me it is, as I don't know nothing about Linux and hardware hacks.

I had to make a blog http://tplinkmr3020wifiradio.blogspot.com/, where I described, actually made a how to, for making the internet radio. I'll put it in order to look nicer and fancy with pictures and rest fancy things these days, but for now I think it is enough.

Only issue that I have is that after I power off router more than 30 seconds it'll not start from USB, and I have to restart it again. After restart everything works fine. Is this normal or it is some kind of bug, or my settings are faulty?

338 (edited by brna 2013-01-14 01:52:56)

Re: TP-Link TL-MR3020 Support

Hey, novi, and hello OpenWRT community.

Novi, tnx for the tutorial, i kinda got stuck at network config  on the same project as yours but on a wr703, and this is very helpful. Pozdrav!

Re: TP-Link TL-MR3020 Support

Pozdrav Brna.

I'm glad that I helped to someone smile

I have one more issue to report, it is regarding ogg stream, I added this issue to blog.
When I start ogg stream everything is ok for about 1-2 seconds, and after that sound starts to be intermittent.I can't figure out what causing this, it is above my knowledge and I need help from someone more competent.

Re: TP-Link TL-MR3020 Support

Now I have no peace...Can someone tell me is it possible to add functionality to WPS button...actually I have idea to start/stop playing the radio stream with one long push, and with one short push to change stations from playlist...and maybe with double click to go back trough playlist smile
As I'm inexperienced with this things I'd appreciate constructive suggestions...(I'm willing to try to make it by myself, but I need some instructions and how to)

Re: TP-Link TL-MR3020 Support

novikorisnik wrote:

Now I have no peace...Can someone tell me is it possible to add functionality to WPS button...actually I have idea to start/stop playing the radio stream with one long push, and with one short push to change stations from playlist...and maybe with double click to go back trough playlist smile
As I'm inexperienced with this things I'd appreciate constructive suggestions...(I'm willing to try to make it by myself, but I need some instructions and how to)

Please check this article in the Wiki: http://wiki.openwrt.org/doc/howto/hardware.button

2x TP-Link TL-MR3020, 2x TP-Link TL-WR703N, 1x TP-Link TL-MR11U, 1x Hame MPR-L8

342 (edited by dddesign 2013-01-18 13:45:59)

Re: TP-Link TL-MR3020 Support

novikorisnik wrote:

actually I have idea to start/stop playing the radio stream with one long push, and with one short push to change stations from playlist...and maybe with double click to go back trough playlist smile

buttons activate:
# opkg update
# opkg install kmod-button-hotplug
# mkdir /etc/hotplug.d/button

for WPS button:
add script in this directory:
/etc/hotplug.d/button/01-wps-button:

#!/bin/sh

#logger $BUTTON
#logger $ACTION
#logger $SEEN

if [ $BUTTON = 'wps' ]
then
    if [ $ACTION = 'pressed' ]; then
        # this is a solution to trigger long pushing:
        date +%s > /tmp/pressed
        /usr/bin/button_pressed &
    fi
    if [ $ACTION = 'released' ]; then
        0 > /tmp/pressed
        if [ $SEEN = 0 ]; then
            #here action for short push (eg next song in mpd):
            logger WPS: NEXT
            mpc next
        fi
    fi
fi

and in /usr/bin/ this script:
/usr/bin/button_pressed:

#!/bin/sh
pressed=`cat /tmp/pressed`
action_2="do" # after 2 sec, "do" it or not ""
action_4="do" # after 4 sec, "do" it or not ""
while [ "`cat /tmp/pressed`" -gt 0 ]; do
    now=`date +%s`
    if [ $now = $((pressed+2)) ] && [ $action_2 = "do" ]; then
        action_2="done"
        #action here (eg play/pause mpd):
        #use it carefully: this actions execute after 2s pressed button, there is no release necessary.
        if [ "$(mpc | grep play)" = "" ]; then
            logger WPS: play
            mpc play
        else
            logger WPS: pause
            mpc pause
        fi
    fi
    if [ $now = $((pressed+4)) ] && [ $action_4 = "do" ]; then
        action_4="done"
        #action here (eg play/pause replay)
        #if the button is still pressed, after the actions before (2sec), following actions execute in addtion
        #use it carefully, these actions are execute after 4s pressed button, no release necessary
        logger WPS: replay
        mpc pause
        mpc play
    fi
done
rm /tmp/pressed

for SLIDER add this script in /etc/hotplug.d
/etc/hotplug.d/button/02-slider:

#!/bin/sh
sleep 1
#logger "log: $BUTTON -- $ACTION"

if [ $ACTION == "released" ] ; then
    if [ $BUTTON == "BTN_1" ] ; then  
        logger "Slider 3G"
        #some actions here
        
    elif [ $BUTTON == "BTN_0" ] && grep -qe "sw1.*in  lo" /sys/kernel/debug/gpio; then
        logger "Slider WISP"
        #some action here

    fi
elif [ $BUTTON == "BTN_0" ] || [ $BUTTON == "BTN_0" ] ; then
    if grep -qe "sw1.*in  hi" /sys/kernel/debug/gpio ; then
        if grep -qe "sw2.*in  hi" /sys/kernel/debug/gpio ; then
            logger "Slider AP"
            #some action here

        fi
    fi
fi

if you want to execute SLIDER scripts while/after booting add this script:
/etc/init.d/button_slider

#!/bin/sh /etc/rc.common

START=19
boot() {
    if grep -qe "sw2.*in  hi" /sys/kernel/debug/gpio ; then
        if grep -qe "sw1.*in  hi" /sys/kernel/debug/gpio ; then
            # AP
            logger AP
            #action here:

        else
            # WISP
            logger WISP
            #action here:

        fi
    else
        # 3G
        logger 3G
        #action here:

    fi
}

and enable it:
# /etc/init.d/button_slider enable

don't forget to make all script executable.

if you find a solution for double-press, let me know.
j

Re: TP-Link TL-MR3020 Support

Hello everyone, how are u? I need a little help, I was using the Openwrt software in my router  MR3020, but I was making some tests with a modem Cmotech CDU-680 and it was not working well, then I decided to go back to the original firmware TP-LINK running the commands in the wiki:

# opkg update && opkg install unzip
# cd /tmp
# wget http://www.tp-link.com/Resources/software/TL-MR3020_V1_120320.zip
# unzip TL-MR3020*.zip
# mtd -r write mr3020*up*.bin firmware


Everything was great until the router reboot, I can ping to 192.168.0.254 ang get answer,  I can connect to the wireless, but when I try to open the web  to http://192.168.0.254, a window pop up and ask for user and password, I wrote it admin:admin, but here is the problem the web gui interface from tplink never start completely, looks like is corrupt or something.  Is there any way to recover the router?  I was reading in the wiki about U-bootloader console. Can I use this method to try to recover the router?  Please a little help.
Thank so much
Regards,
Victor

Re: TP-Link TL-MR3020 Support

I flashed the openwrt rc1 on my tl mr3020, everything is going fine, I can connect to internet using the router

The only problem is I can't seem to access the luci webgui at 192.168.1.1 via wifi, I can only access it from lan connection

Even telnet and SSH to 192.168.1.1 via wifi failed

So everytime I need to change some configs, I must connect the router via the lan port, then I can access the webgui via 192.168.1.1

What's wrong ?

Re: TP-Link TL-MR3020 Support

paleskin wrote:

I flashed the openwrt rc1 on my tl mr3020, everything is going fine, I can connect to internet using the router

The only problem is I can't seem to access the luci webgui at 192.168.1.1 via wifi, I can only access it from lan connection

Even telnet and SSH to 192.168.1.1 via wifi failed

So everytime I need to change some configs, I must connect the router via the lan port, then I can access the webgui via 192.168.1.1

What's wrong ?

You have to add a firewall rule to open access to TCP port 80 to get access to webadmin from wan, and to TCP port 22 for SSH access from wan.

This can be done from the webadmin itnerface, under "Network > Firewall > Trafic Rules".

2x TP-Link TL-MR3020, 2x TP-Link TL-WR703N, 1x TP-Link TL-MR11U, 1x Hame MPR-L8

Re: TP-Link TL-MR3020 Support

Squonk wrote:
paleskin wrote:

I flashed the openwrt rc1 on my tl mr3020, everything is going fine, I can connect to internet using the router

The only problem is I can't seem to access the luci webgui at 192.168.1.1 via wifi, I can only access it from lan connection

Even telnet and SSH to 192.168.1.1 via wifi failed

So everytime I need to change some configs, I must connect the router via the lan port, then I can access the webgui via 192.168.1.1

What's wrong ?

You have to add a firewall rule to open access to TCP port 80 to get access to webadmin from wan, and to TCP port 22 for SSH access from wan.

This can be done from the webadmin itnerface, under "Network > Firewall > Trafic Rules".

Done, but still I can't access the webgui via wifi

Could u guide me step by step ?

Thanks

Re: TP-Link TL-MR3020 Support

Hello.
I have read http://wiki.openwrt.org/toh/tp-link/tl-mr3020 and try to update openwrt on my mr3020.

I have installed openwrt-ar71xx-generic-tl-mr3020-v1-squashfs-sysupgrade.bin from

http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/

and then cant install for example luci package:

root@OpenWrt:~# opkg update
Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/Packages.gz.
Updated list of available packages in /var/opkg-lists/barrier_breaker.
root@OpenWrt:~#
root@OpenWrt:~# opkg install luci
Unknown package 'luci'.
Collected errors:
 * opkg_install_cmd: Cannot install package luci.
root@OpenWrt:~#

should I return to AArc1 or there is other fresh firmware for my router ?

please advice

Re: TP-Link TL-MR3020 Support

Either go to AArc1 (least painful option)
Or build your own + packages
Or wait until the build bots have finished updating the packages (luci is not yet compiled, as you found out).

Re: TP-Link TL-MR3020 Support

can't connect via 3G "serial line is not 8 bit clean"

My Huawei E160 (Aldi-Stick) was doing his work properly half a year ago in Germany with eplus.

I made a new test today and got the message "serial line is not 8 bit clean"

I had a similar problem in sweden with telenor past the 1. July, before it was working well.

The stick is running without problems with the original software

help appreciated

This is the syslog

Jul 15 15:40:06 OpenWrt kern.debug kernel: [    0.000000]   Normal zone: 0 pages reserved
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    0.000000]   Normal zone: 8128 pages, LIFO batch:0
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    0.000000] pcpu-alloc: [0] 0
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.000000] Kernel command line:  board=TL-MR3020 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Writing ErrCtl register=00000000
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Readback ErrCtl register=00000000
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Memory: 29312k/32768k available (2072k kernel code, 3456k reserved, 390k data, 200k init, 0k highmem)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] NR_IRQS:48
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.080000] pid_max: default: 32768 minimum: 301
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.080000] Mount-cache hash table entries: 512
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.090000] NET: Registered protocol family 16
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.100000] MIPS: machine is TP-LINK TL-MR3020
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.340000] bio: create slab <bio-0> at 0
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.340000] Switching to clocksource MIPS
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.350000] NET: Registered protocol family 2
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.350000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.370000] TCP: Hash tables configured (established 1024 bind 1024)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.380000] TCP reno registered
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.390000] NET: Registered protocol family 1
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    0.400000] PCI: CLS 0 bytes, default 32
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.430000] msgmni has been set to 57
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.430000] io scheduler noop registered
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.440000] io scheduler deadline registered (default)
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.440000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.450000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.450000] console [ttyATH0] enabled, bootconsole disabled
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.470000] m25p80 spi0.0: found s25sl032a, expected m25p80
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.470000] m25p80 spi0.0: s25sl032a (4096 Kbytes)
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.480000] 5 tp-link partitions found on MTD device spi0.0
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.480000] Creating 5 MTD partitions on "spi0.0":
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.490000] 0x000000000000-0x000000020000 : "u-boot"
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.490000] 0x000000020000-0x0000000fc3cc : "kernel"
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.500000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.510000] 0x0000000fc3cc-0x0000003f0000 : "rootfs"
Jul 15 15:40:06 OpenWrt kern.warn kernel: [    0.520000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.530000] mtd: partition "rootfs" set to be root filesystem
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.530000] mtd: partition "rootfs_data" created automatically, ofs=350000, len=A0000
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.540000] 0x000000350000-0x0000003f0000 : "rootfs_data"
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.550000] 0x0000003f0000-0x000000400000 : "art"
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    0.550000] 0x000000020000-0x0000003f0000 : "firmware"
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.800000] ag71xx_mdio: probed
Jul 15 15:40:06 OpenWrt kern.info kernel: [    0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.410000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.410000] TCP westwood registered
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.420000] NET: Registered protocol family 17
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.420000] 8021q: 802.1Q VLAN Support v1.8
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.430000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Jul 15 15:40:06 OpenWrt kern.info kernel: [    1.440000] Freeing unused kernel memory: 200k freed
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    3.650000] Registered led device: tp-link:green:3g
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    3.650000] Registered led device: tp-link:green:wlan
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    3.650000] Registered led device: tp-link:green:lan
Jul 15 15:40:06 OpenWrt kern.debug kernel: [    3.650000] Registered led device: tp-link:green:wps
Jul 15 15:40:06 OpenWrt kern.info kernel: [    6.770000] eth0: link up (100Mbps/Full duplex)
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    6.970000] JFFS2 notice: (415) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 30 of xref (0 dead, 19 orphan) found.
Jul 15 15:40:06 OpenWrt kern.info kernel: [    7.170000] eth0: link down
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.110000] Compat-wireless backport release: compat-wireless-2012-04-17-2-r31672
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.110000] Backport based on wireless-testing.git master-2012-04-17
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.200000] cfg80211: Calling CRDA to update world regulatory domain
Jul 15 15:40:06 OpenWrt kern.notice kernel: [    9.610000] SCSI subsystem initialized
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.860000] usbcore: registered new interface driver usbfs
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.860000] usbcore: registered new interface driver hub
Jul 15 15:40:06 OpenWrt kern.info kernel: [    9.940000] usbcore: registered new device driver usb
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.120000] cfg80211: World regulatory domain updated:
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.130000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.140000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.140000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.150000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.160000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.170000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: EEPROM regdomain: 0x0
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: EEPROM indicates default country code should be used
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: doing EEPROM country->regdmn map search
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: country maps to regdmn code: 0x3a
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: Country alpha2 being used: US
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.730000] ath: Regpair used: 0x3a
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.740000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Jul 15 15:40:06 OpenWrt kern.debug kernel: [   10.740000] Registered led device: ath9k-phy0
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.740000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.750000] cfg80211: Calling CRDA for country: US
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.970000] cfg80211: Regulatory domain changed to country: US
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.970000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.980000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.990000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   10.990000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.000000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.010000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.020000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.550000] PPP generic driver version 2.4.2
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.700000] ip_tables: (C) 2000-2006 Netfilter Core Team
Jul 15 15:40:06 OpenWrt kern.info kernel: [   11.910000] NET: Registered protocol family 24
Jul 15 15:40:06 OpenWrt kern.info kernel: [   12.160000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jul 15 15:40:06 OpenWrt kern.info kernel: [   12.170000] ehci-platform ehci-platform: Generic Platform EHCI Controller
Jul 15 15:40:08 OpenWrt kern.info kernel: [   16.860000] device wlan0 entered promiscuous mode
Jul 15 15:40:10 OpenWrt kern.info kernel: [   19.450000] device wlan0 left promiscuous mode
Jul 15 15:40:10 OpenWrt kern.info kernel: [   19.460000] br-lan: port 1(wlan0) entered disabled state
Jul 15 15:40:11 OpenWrt kern.info kernel: [   19.600000] device wlan0 entered promiscuous mode
Jul 15 15:40:11 OpenWrt user.info sysinit: Loading defaults
Jul 15 15:40:11 OpenWrt kern.info kernel: [   20.440000] usb 1-1.3: new high-speed USB device number 6 using ehci-platform
Jul 15 15:40:11 OpenWrt kern.info kernel: [   20.580000] option 1-1.3:1.0: GSM modem (1-port) converter detected
Jul 15 15:40:11 OpenWrt kern.info kernel: [   20.580000] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB2
Jul 15 15:40:12 OpenWrt kern.info kernel: [   20.610000] option 1-1.3:1.1: GSM modem (1-port) converter detected
Jul 15 15:40:12 OpenWrt kern.info kernel: [   20.620000] usb 1-1.3: GSM modem (1-port) converter now attached to ttyUSB3
Jul 15 15:40:12 OpenWrt user.info sysinit: Loading synflood protection
Jul 15 15:40:12 OpenWrt kern.info kernel: [   20.660000] scsi3 : usb-storage 1-1.3:1.2
Jul 15 15:40:12 OpenWrt kern.info kernel: [   20.660000] scsi4 : usb-storage 1-1.3:1.3
Jul 15 15:40:12 OpenWrt user.notice gpsd: Starting...
Jul 15 15:40:12 OpenWrt user.notice try to start gpsd with : /dev/ttyUSB0   /dev/ttyUSB1
Jul 15 15:40:12 OpenWrt user.info sysinit: Adding custom chains
Jul 15 15:40:12 OpenWrt user.notice gpsd[953]: gpsd:ERROR: can't create IPv6 socket
Jul 15 15:40:13 OpenWrt kern.notice kernel: [   21.660000] scsi 3:0:0:0: CD-ROM            HUAWEI   Mass Storage     2.31 PQ: 0 ANSI: 2
Jul 15 15:40:13 OpenWrt kern.notice kernel: [   21.670000] scsi 4:0:0:0: Direct-Access     HUAWEI   MMC Storage      2.31 PQ: 0 ANSI: 2
Jul 15 15:40:13 OpenWrt kern.notice kernel: [   21.710000] sd 4:0:0:0: [sda] Attached SCSI removable disk
Jul 15 15:40:13 OpenWrt user.info sysinit: Loading zones
Jul 15 15:40:14 OpenWrt user.info sysinit: Loading forwardings
Jul 15 15:40:14 OpenWrt user.info sysinit: Loading rules
Jul 15 15:40:15 OpenWrt user.info sysinit: Loading redirects
Jul 15 15:40:15 OpenWrt user.info sysinit: Loading includes
Jul 15 15:40:15 OpenWrt user.info sysinit: Optimizing conntrack
Jul 15 15:40:15 OpenWrt user.info sysinit: Loading interfaces
Jul 15 15:40:16 OpenWrt user.notice ifup: Enabling Router Solicitations on loopback (lo)
Jul 15 15:40:16 OpenWrt kern.info kernel: [   24.960000] device eth0 entered promiscuous mode
Jul 15 15:40:16 OpenWrt kern.info kernel: [   25.030000] eth0: link up (100Mbps/Full duplex)
Jul 15 15:40:16 OpenWrt authpriv.info dropbear[1181]: Running in background
Jul 15 15:40:17 OpenWrt kern.info kernel: [   26.450000] br-lan: port 2(eth0) entered forwarding state
Jul 15 15:40:17 OpenWrt kern.info kernel: [   26.450000] br-lan: port 2(eth0) entered forwarding state
Jul 15 15:40:17 OpenWrt kern.info kernel: [   26.450000] br-lan: port 1(wlan0) entered forwarding state
Jul 15 15:40:17 OpenWrt kern.info kernel: [   26.460000] br-lan: port 1(wlan0) entered forwarding state
Jul 15 15:40:18 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul 15 15:40:19 OpenWrt user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Jul 15 15:40:21 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq[1406]: started, version 2.59 cachesize 150
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq[1406]: compile time options: IPv6 GNU-getopt no-DBus no-i18n DHCP TFTP no-conntrack no-IDN
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq-dhcp[1406]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq[1406]: using local addresses only for domain lan
Jul 15 15:40:22 OpenWrt daemon.warn dnsmasq[1406]: no servers found in /tmp/resolv.conf.auto, will retry
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq[1406]: read /etc/hosts - 1 addresses
Jul 15 15:40:22 OpenWrt daemon.info dnsmasq-dhcp[1406]: read /etc/ethers - 0 addresses
Jul 15 15:40:22 OpenWrt user.info sysinit: setting up led USB
Jul 15 15:40:22 OpenWrt user.info sysinit: setting up led WLAN
Jul 15 15:40:22 OpenWrt user.info sysinit: setting up led LAN


Jul 15 15:40:26 OpenWrt daemon.info dnsmasq-dhcp[1406]: DHCPREQUEST(br-lan) 192.168.1.135 04:7d:7b:09:2f:b5
Jul 15 15:40:26 OpenWrt daemon.info dnsmasq-dhcp[1406]: DHCPACK(br-lan) 192.168.1.135 04:7d:7b:09:2f:b5 TOSH_I7
Jul 15 15:40:31 OpenWrt daemon.info dnsmasq-dhcp[1406]: DHCPINFORM(br-lan) 192.168.1.135 04:7d:7b:09:2f:b5
Jul 15 15:40:31 OpenWrt daemon.info dnsmasq-dhcp[1406]: DHCPACK(br-lan) 192.168.1.135 04:7d:7b:09:2f:b5 TOSH_I7
Jul 15 15:40:32 OpenWrt kern.info kernel: [   41.480000] br-lan: port 2(eth0) entered forwarding state
Jul 15 15:40:32 OpenWrt kern.info kernel: [   41.480000] br-lan: port 1(wlan0) entered forwarding state
Jul 15 15:42:06 OpenWrt daemon.notice pppd[1580]: pppd 2.4.5 started by root, uid 0
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: abort on (BUSY)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: abort on (NO CARRIER)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: abort on (ERROR)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: report (CONNECT)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: timeout set to 10 seconds
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: send (AT&F^M)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: expect (OK)
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: AT&F^M^M
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: OK
Jul 15 15:42:07 OpenWrt local2.info chat[1598]:  -- got it
Jul 15 15:42:07 OpenWrt local2.info chat[1598]: send (ATE1^M)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: expect (OK)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: ^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: ATE1^M^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: OK
Jul 15 15:42:08 OpenWrt local2.info chat[1598]:  -- got it
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: send (AT+CGDCONT=1,"IP","internet.eplus.de"^M)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: timeout set to 30 seconds
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: expect (OK)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: ^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: AT+CGDCONT=1,"IP","internet.eplus.de"^M^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: OK
Jul 15 15:42:08 OpenWrt local2.info chat[1598]:  -- got it
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: send (ATD*99***1#^M)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: expect (CONNECT)
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: ^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: ATD*99***1#^M^M
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: CONNECT
Jul 15 15:42:08 OpenWrt local2.info chat[1598]:  -- got it
Jul 15 15:42:08 OpenWrt local2.info chat[1598]: send ( ^M)
Jul 15 15:42:08 OpenWrt daemon.info pppd[1580]: Serial connection established.
Jul 15 15:42:08 OpenWrt daemon.info pppd[1580]: Using interface 3g-wan
Jul 15 15:42:08 OpenWrt daemon.notice pppd[1580]: Connect: 3g-wan <--> /dev/ttyUSB3

Jul 15 15:42:39 OpenWrt daemon.warn pppd[1580]: LCP: timeout sending Config-Requests
Jul 15 15:42:39 OpenWrt daemon.notice pppd[1580]: Connection terminated.
Jul 15 15:42:39 OpenWrt daemon.warn pppd[1580]: Receive serial link is not 8-bit clean:
Jul 15 15:42:39 OpenWrt daemon.warn pppd[1580]: Problem: all had bit 7 set to 0
Jul 15 15:42:40 OpenWrt daemon.notice pppd[1580]: Modem hangup

Re: TP-Link TL-MR3020 Support

robthebrew

so there is chance that package for luci and mjpg-streamer that also not available for now will be compiled after some time and will appear in http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/ ?

when it will be done ? when I should check this folder ? Is there some info about time how buildbot works ?