OpenWrt Forum Archive

Topic: [Photo Sagem 2404 motherboard] help me find the serial port?

The content of this topic has been archived on 21 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hi I have cleared my sagem but not right where the serial port. Where is RX and TX?

http://www.3gspain.org/sagem.jpg

http://www.3gspain.org/sagem.jpg

(Last edited by juander on 17 Sep 2009, 23:04)

You'll have to solder a four pin header in the space right below the ethernet switch.

The pin nearest to the switch looks like ground, then probably tx and rx (going down).

That's what I figured but there are a number of components without soldering just below, do not influence?

This router also has usb?

(Last edited by juander on 18 Sep 2009, 09:50)

I have seen two possible RX and TX, a default one is at 0V and the other at 2.8V, that you think?

If I convert the signals between router and PC with a MAX232, does it break?

http://www.3gspain.org/sagem2.jpg

(Last edited by juander on 19 Sep 2009, 10:44)

http://images38.fotosik.pl/197/857e62350fe3a8ab.jpg

Thank, to connect your PC to the router can I use MAX232?

It is better to use MAX3232, or mobile phone datacable like Nokia DKU-5. I am using Siemens mobile datacable with Prolific PL2303 chip.

How upload the firmware? How is the cable connected properly?

juander, the pinouts  is (bottom) gnd - tx - rx  - vcc  (top)
http://img12.imageshack.us/img12/3689/patata.jpg http://img12.imageshack.us/img12/patata.jpg/1/w2048.png
Original FIrmware Serial Output:

Sagem CFE version: 3.13.5                          
Build Date: Mon May 14 17:56:09 CST 2007 
(shenmc@svr1.sagemharbournetworks.com)
Copyright (C) 2005-2006 Sagem communication.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB
Enter readNvramData(CFE)
Enter kerSysNvRamGet(CFE)
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404  
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz                               
Total memory: 16777216 bytes (16MB)                                             
                                                                                
Total memory used by CFE:  0x80401000 - 0x80528470 (1209456)                    
Initialized Data:          0x8041EAE0 - 0x80421AB0 (12240)                      
BSS Area:                  0x80421AB0 - 0x80426470 (18880)                      
Local Heap:                0x80426470 - 0x80526470 (1048576)                    
Stack Area:                0x80526470 - 0x80528470 (8192)                       
Text (code) segment:       0x80401000 - 0x8041EAD8 (121560)                     
Boot area (physical):      0x00529000 - 0x00569000                              
Relocation Factor:         I:00000000 - D:00000000                              
                                                                                
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Enter readNvramData(CFE)                                                        
Enter kerSysNvRamGet(CFE)                                                       
kerSysNvRamGet(CFE) Mac address:00:19:4b:b4:dd:aa, BoardId=F@ST2404             
Board IP address                  : 192.168.1.1:ffffff00                        
Host IP address                   : 192.168.1.28                                
Gateway IP address                :                                             
Run from flash/host (f/h)         : f                                           
Default host run file name        : vmlinux                                     
Default host flash file name      : bcm963xx_fs_kernel                          
Boot delay (0-9 seconds)          : 1                                           
Board Id Name                     : F@ST2404                                    
Psi size in KB                    : 24                                          
Number of MAC Addresses (1-32)    : 11                                          
Base MAC Address                  : 00:19:4b:b4:dd:aa                           
Ethernet PHY Type                 : Internal                                    
Memory size in MB                 : 16                                          
CMT Thread Number                 : 0                                           
Customer Name                     :SAGM(default)                                
                                                                                
*** Press any key to stop auto run (1 seconds) ***                              
Auto run second count down: 0                                                   
Code Address: 0x80010000, Entry Address: 0x801c6018                             
Decompression OK!                                                               
Entry at 0x801c6018                                                             
Closing network.                                                                
Starting program at 0x801c6018                                                  
Linux version 2.6.8.1 (chenc@svr1.sagem-szn.com) (gcc version 3.4.2) #1 
Wed Jun8
Parallel flash device: name SST39VF3201, id 0x235b, size 4096KB                 
Total Flash size: 4096K with 1024 sectors                                       
fInfo.flash_scratch_pad_start_blk = 1016                                        
fInfo.flash_scratch_pad_number_blk = 2                                          
fInfo.flash_scratch_pad_length = 0x2000                                         
fInfo.flash_scratch_pad_blk_offset = 0x0                                        
                                                                                
fInfo.flash_nvram_start_blk = 0                                                 
fInfo.flash_nvram_blk_offset = 0x580                                            
fInfo.flash_nvram_number_blk = 1                                                
                                                                                
fInfo.flash_persistent_start_blk = 1018                                         
fInfo.flash_persistent_blk_offset = 0x0                                         
fInfo.flash_persistent_number_blk = 6                                           
                                                                                
backup_start_blk = 1010                                                         
backup_blk_offset = 0x0                                                         
backup_number_blk = 6                                                           
backup_length = 24576                                                           
                                                                                
psi startAddr = bfffa000                                                        
sp startAddr = bfff8000                                                         
backup startAddr = bfff2000                                                     
                                                                                
F@ST2404 prom init                                                              
CPU revision is: 00029107                                                       
Determined physical RAM map:                                                    
 memory: 00fa0000 @ 00000000 (usable)                                           
On node 0 totalpages: 4000                                                      
  DMA zone: 4000 pages, LIFO batch:1                                            
  Normal zone: 0 pages, LIFO batch:1                                            
  HighMem zone: 0 pages, LIFO batch:1                                           
Built 1 zonelists                                                               
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200                 
brcm mips: enabling icache and dcache...                                        
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 
bytes.    
Primary data cache 8kB 2-way, linesize 16 bytes.                                
PID hash table entries: 64 (order 6: 512 bytes)                                 
Using 128.000 MHz high precision timer.                                         
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)                   
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)                     
Memory: 13816k/16000k available (1515k kernel code, 2164k reserved, 233k 
data, )
Calibrating delay loop... 254.77 BogoMIPS                                       
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)                      
Checking for 'wait' instruction...  unavailable.                                
NET: Registered protocol family 16                                              
Can't analyze prologue code at 80189494                                         
usbcore: registered new driver hub                                              
Initializing Cryptographic API                                                  
PPP generic driver version 2.4.2                                                
NET: Registered protocol family 24                                              
Using noop io scheduler                                                         
bcm963xx_mtd driver v1.0                                                        
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)        
ohci_hcd: block sizes: ed 64 td 64                                              
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)                                
ohci_hcd 0000:00:09.0: OHCI Host Controller                                     
PCI: Setting latency timer of device 0000:00:09.0 to 64                         
ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00                                 
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1            
hub 1-0:1.0: USB hub found                                                      
hub 1-0:1.0: 2 ports detected                                                   
usbcore: registered new driver usblp                                            
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver               
brcmboard: brcm_board_init entry                                                
RestoreMacFilter: Button GPIO 0x21 is enabled                                   
RestoreMacFilter: Button Interrupt 0x1 is enabled                               
RestoreMacFilter: Interrupt mapping OK                                          
Serial: BCM63XX driver $Revision: 1.3 $                                         
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX                                
NET: Registered protocol family 2                                               
IP: routing cache hash table of 512 buckets, 4Kbytes                            
********* ip_rt_init ************                                               
sizeof(struct rtable)=244                                                       
ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512,              
ip_rt_gc_interval=12000, rt_secret_rebuild=120000                               
TCP: Hash tables configured (established 512 bind 1024)                         
Initializing IPsec netlink socket                                               
NET: Registered protocol family 1                                               
NET: Registered protocol family 17                                              
NET: Registered protocol family 15                                              
Ebtables v2.0 registered                                                        
NET: Registered protocol family 8                                               
NET: Registered protocol family 20                                              
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>                   
All bugs added by David S. Miller <davem@redhat.com>                            
VFS: Mounted root (squashfs filesystem) readonly.                               
Freeing unused kernel memory: 72k freed                                         
init started:  BusyBox v1.00 (2008.06.25-10:09+0000) multi-call binary          
Algorithmics/MIPS FPU Emulator v1.5                                             
mount: Mounting tmpfs on /tmp failed: No such file                              
                                                                                
BusyBox v1.00 (2008.06.25-10:09+0000) Built-in shell (msh)                      
Enter 'help' for a list of built-in commands.                                   
                                                                                
                                                                                
Loading drivers and kernel modules...                                           
                                                                                
atmapi: module license 'Proprietary' taints kernel.                             
adsl: adsl_init entry                                                           
blaadd: blaa_detect entry                                                       
Broadcom BCMPROCFS v1.0 initialized                                             
Broadcom BCM6348B0 Ethernet Network Device v0.3 Jun 25 2008 18:01:31            
Config Ethernet Switch Through SPI Slave Select 0                               
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered                          
eth0: MAC Address: 00:19:4B:B4:DD:AA                                            
Cfm wathcer has been setup!                                                     
PCI: Setting latency timer of device 0000:00:01.0 to 64                         
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)                                
wl: srom not detected, using main memory mapped srom info (wombo board)         
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000            
wl0: MAC Address: 00:19:4B:B4:DD:AB                                             
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2             
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered                           
eth0 Link UP.                                                                   
Cfm has been started to initiate!                                               
Read Flash: part=[PERSISTENT]                                                   
Read Flash: part=[PERSISTENT]                                                   
PSI has been initiated successfully!                                            
BcmAdsl_Initialize=0xC006D928, g_pFnNotifyCallback=0xC0088D14                   
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000                  
pSdramPHY=0xA0FFFFF8, 0x28041 0x9689ACE8                                        
AdslCoreHwReset:  AdslOemDataAddr = 0xA0FFBB64                                  
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000                  
Read Flash: part=[FACTORYINFO]                                                  
Enter kerSysFactoryInfoGet: strLen[256],offset[0]                               
FactoryInfo[1-10]=[??????????]                                                  
ATM proc init !!!                                                               
ATM Config Management initiated successfully!                                   
Security configuration management initiated successfully!                       
                                                                                
==>   Software Version: 3.24a4  <==                                             
                                                                                
device eth0 entered promiscuous mode                                            
br0: port 1(eth0) entering learning state                                       
br0: topology change detected, propagating                                      
br0: port 1(eth0) entering forwarding state                                     
Setting SSID "Sagem"                                                            
Setting SSID "Guest"                                                            
Setting country code using abbreviation: "FR"                                   
wlctl band b run 0 time!                                                        
wlctl band b run 0 time!                                                        
channel 11 selected                                                             
device wl0 entered promiscuous mode                                             
br0: port 2(wl0) entering learning state                                        
br0: topology change detected, propagating                                      
br0: port 2(wl0) entering forwarding state                                      
device wl0.1 entered promiscuous mode                                           
br0: port 3(wl0.1) entering learning state                                      
br0: topology change detected, propagating                                      
br0: port 3(wl0.1) entering forwarding state                                    
EngDbg:- PSI Retrieve Status for PortMirrorStatus = 3                           
EngDbg:- In Effect Port Mirror Cfg                                              
ENGDBG :- In Effect Port Mirroring, status = 0   count = 0                      
Read Flash: part=[SCRATCH_PAD]                                                  
Read Flash: part=[SCRATCH_PAD]                                                  
Network initiated successfully!                                                 
Web Server initiated successfully!                                              
Read Flash: part=[SCRATCH_PAD]                                                  
Cfm initiated successfully!                                                     
No POSTINIT command need excuting                                               
Admin URL is blank, then don't start RemoteAutoUpgradeThread                    
========>Load the wireless_reload_monitor thread<=======                        
nat_cache: Unknown symbol invert_tuplepr                                        
nat_cache: Unknown symbol ip_ct_find_helper                                     
nat_cache: Unknown symbol ip_ct_refresh                                         
insmod: cannot insert 
`/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/s
--->syslog_options_up: blocksite unloged!                                       
nat_cache: Unknown symbol invert_tuplepr                                        
nat_cache: Unknown symbol ip_ct_find_helper                                     
nat_cache: Unknown symbol ip_ct_refresh                                         
insmod: cannot insert 
`/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/s
Read Flash: part=[FACTORYINFO]                                                  
Enter kerSysFactoryInfoGet: strLen[1024],offset[0]                              
FactoryInfo[1-10]=[??????????]

is there any pre-built image ? Because the latest f@ast2404-cfe, from 8.09 rc2  gets partition error...
thx

Has anyone succeeded in porting openwrt to the sagem fast 2404 / 2504 / 2604 ? if so, how? probably my isp will be giving me one soon.

flash is unusable... so no filesystem tongue

But there must be some way, why doesn't the bootloader load the image? wrong headers/checksums? some compression algorithms we're not using? How about replacing the bootloader?

naplam wrote:

But there must be some way, why doesn't the bootloader load the image? wrong headers/checksums? some compression algorithms we're not using? How about replacing the bootloader?

no, no.. the bootloader does load the image.
see bug tracker

Ok, so we just have to figure out the original firmware organization in the flash memory and mimic that, right? our kernel is being loaded but the squashfs partition is not the right place/the flash is not correctly partitioned, is that it?

(Last edited by naplam on 16 Jan 2010, 00:31)

naplam wrote:

Ok, so we just have to figure out the original firmware organization in the flash memory and mimic that, right? our kernel is being loaded but the squashfs partition is not the right place/the flash is not correctly partitioned, is that it?

exacto wink

cat /proc/mtd                                                                 
dev:    size   erasesize  name                                                  
mtd0: 002d1000 00001000 "Physically mapped flash"

tehere's only one partition mtd0 ...
these days i've been flashing an ar7 so i know mtd partitions may be redefined... but  ¿how can this be done in cfe? ¿deosn't the bin image redefine the map?

(Last edited by DeerHunter on 16 Jan 2010, 00:55)

DeerHunter, how do you log in with the original firmware? i have a tacky configuration interface in the sagem 2604 in telnet and ssh, not a shell. Also, mtdX are not mentioned in the system logs, another naming is used ("read flash: part [factory] things like that instead of mtd0 or 1 o2 whatever, you can see it in the log.

edit: i see your 2404 log is almost identical
edit: i guess you're getting a shell from the serial console smile
edit(2): i can get a shell by typing sh in the tacky menu instead of an option number

edit(3): some info:

# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/mtdblock0            3200      3200         0 100% /
tmpfs                      320       136       184  43% /var
tmpfs                       16         0        16   0% /mnt
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00313000 00001000 "Physically mapped flash"
# cat cpuinfo
system type             : F@ST2604
processor               : 0
cpu model               : BCM6348 V0.7
BogoMIPS                : 254.77
wait instruction        : no
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : yes
hardware watchpoint     : no
VCED exceptions         : not available
VCEI exceptions         : not available

I post it here in case it can help anyone with a 2404 or 2604 and similar hardware.

System Log:
      date                      facility        severity        message
      Jan  1 00:00:30           user            warn           kernel: backup_number_blk = 6
      Jan  1 00:00:30           user            warn           kernel: backup_length = 24576
      Jan  1 00:00:30           user            warn           kernel: 
      Jan  1 00:00:30           user            warn           kernel: psi startAddr = bfffa000
      Jan  1 00:00:30           user            warn           kernel: systemini startAddr = bfff9000
      Jan  1 00:00:30           user            warn           kernel: sp startAddr = bfff8000
      Jan  1 00:00:30           user            warn           kernel: backup startAddr = bfff2000
      Jan  1 00:00:30           user            warn           kernel: 
      Jan  1 00:00:30           user            warn           kernel: F@ST2604 prom init
      Jan  1 00:00:30           user            warn           kernel: CPU revision is: 00029107
      Jan  1 00:00:30           user            warn           kernel: Determined physical RAM map:
      Jan  1 00:00:30           user            warn           kernel:  memory: 00fa0000 @ 00000000 (usable)
      Jan  1 00:00:30           user            debug          kernel: On node 0 totalpages: 4000
      Jan  1 00:00:30           user            debug          kernel:   DMA zone: 4000 pages, LIFO batch:1
      Jan  1 00:00:30           user            debug          kernel:   Normal zone: 0 pages, LIFO batch:1
      Jan  1 00:00:30           user            debug          kernel:   HighMem zone: 0 pages, LIFO batch:1
      Jan  1 00:00:30           user            warn           kernel: Built 1 zonelists
      Jan  1 00:00:30           user            warn           kernel: Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
      Jan  1 00:00:30           user            warn           kernel: brcm mips: enabling icache and dcache...
      Jan  1 00:00:30           user            warn           kernel: Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
      Jan  1 00:00:30           user            warn           kernel: Primary data cache 8kB 2-way, linesize 16 bytes.
      Jan  1 00:00:30           user            warn           kernel: PID hash table entries: 64 (order 6: 512 bytes)
      Jan  1 00:00:30           user            warn           kernel: Using 128.000 MHz high precision timer.
      Jan  1 00:00:30           user            warn           kernel: Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
      Jan  1 00:00:30           user            warn           kernel: Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
      Jan  1 00:00:30           user            info           kernel: Memory: 13816k/16000k available (1516k kernel code, 2164k reserved, 232k data, 72k init, 0k highmem)
      Jan  1 00:00:30           user            warn           kernel: Calibrating delay loop... 254.77 BogoMIPS
      Jan  1 00:00:30           user            warn           kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
      Jan  1 00:00:30           user            warn           kernel: Checking for 'wait' instruction...  unavailable.
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 16
      Jan  1 00:00:30           user            warn           kernel: Can't analyze prologue code at 80189904
      Jan  1 00:00:30           user            info           kernel: usbcore: registered new driver hub
      Jan  1 00:00:30           user            info           kernel: Initializing Cryptographic API
      Jan  1 00:00:30           user            info           kernel: PPP generic driver version 2.4.2
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 24
      Jan  1 00:00:30           user            warn           kernel: Using noop io scheduler
      Jan  1 00:00:30           user            warn           kernel: bcm963xx_mtd driver v1.0
      Jan  1 00:00:30           user            debug          kernel: ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
      Jan  1 00:00:30           user            debug          kernel: ohci_hcd: block sizes: ed 64 td 64
      Jan  1 00:00:30           user            warn           kernel: PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
      Jan  1 00:00:30           user            info           kernel: ohci_hcd 0000:00:09.0: OHCI Host Controller
      Jan  1 00:00:30           user            debug          kernel: PCI: Setting latency timer of device 0000:00:09.0 to 64
      Jan  1 00:00:30           user            info           kernel: ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00
      Jan  1 00:00:30           user            info           kernel: ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
      Jan  1 00:00:30           user            info           kernel: hub 1-0:1.0: USB hub found
      Jan  1 00:00:30           user            info           kernel: hub 1-0:1.0: 2 ports detected
      Jan  1 00:00:30           user            info           kernel: usbcore: registered new driver usblp
      Jan  1 00:00:30           user            info           kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
      Jan  1 00:00:30           user            warn           kernel: brcmboard: brcm_board_init entry
      Jan  1 00:00:30           user            warn           kernel: RestoreMacFilter: Button GPIO 0x21 is enabled
      Jan  1 00:00:30           user            warn           kernel: RestoreMacFilter: Button Interrupt 0x1 is enabled
      Jan  1 00:00:30           user            warn           kernel: RestoreMacFilter: Interrupt mapping OK
      Jan  1 00:00:30           user            info           kernel: Serial: BCM63XX driver $Revision: 1.3 $
      Jan  1 00:00:30           user            warn           kernel: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 2
      Jan  1 00:00:30           user            info           kernel: IP: routing cache hash table of 512 buckets, 4Kbytes
      Jan  1 00:00:30           user            warn           kernel: ********* ip_rt_init ************
      Jan  1 00:00:30           user            warn           kernel: sizeof(struct rtable)=244
      Jan  1 00:00:30           user            warn           kernel: ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512, 
      Jan  1 00:00:30           user            warn           kernel: ip_rt_gc_interval=12000, rt_secret_rebuild=120000
      Jan  1 00:00:30           user            info           kernel: TCP: Hash tables configured (established 512 bind 1024)
      Jan  1 00:00:30           user            info           kernel: Initializing IPsec netlink socket
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 1
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 17
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 15
      Jan  1 00:00:30           user            notice         kernel: Ebtables v2.0 registered
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 8
      Jan  1 00:00:30           user            info           kernel: NET: Registered protocol family 20
      Jan  1 00:00:30           user            info           kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
      Jan  1 00:00:30           user            info           kernel: All bugs added by David S. Miller <davem@redhat.com>
      Jan  1 00:00:30           user            warn           kernel: VFS: Mounted root (squashfs filesystem) readonly.
      Jan  1 00:00:30           user            info           kernel: Freeing unused kernel memory: 72k freed
      Jan  1 00:00:30           user            warn           kernel: Algorithmics/MIPS FPU Emulator v1.5
      Jan  1 00:00:30           user            warn           kernel: atmapi: module license 'Proprietary' taints kernel.
      Jan  1 00:00:30           user            warn           kernel: adsl: adsl_init entry
      Jan  1 00:00:30           user            warn           kernel: entry
      Jan  1 00:00:30           user            info           kernel: Broadcom BCMPROCFS v1.0 initialized
      Jan  1 00:00:30           user            warn           kernel: Broadcom BCM6348B0 Ethernet Network Device v0.3 Jan 19 2009 17:23:25
      Jan  1 00:00:30           user            warn           kernel: Config Ethernet Switch Through SPI Slave Select 0
      Jan  1 00:00:30           user            warn           kernel: Cfm wathcer has been setup!
      Jan  1 00:00:30           user            warn           kernel: dgasp: kerSysRegisterDyingGaspHandler: eth0 registered 
      Jan  1 00:00:30           user            warn           kernel: eth0: MAC Address: 00:26:91:20:84:16
      Jan  1 00:00:30           user            debug          kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
      Jan  1 00:00:30           user            warn           kernel: PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
      Jan  1 00:00:30           user            warn           kernel: wl: srom not detected, using main memory mapped srom info (wombo board)
      Jan  1 00:00:30           user            warn           kernel: wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
      Jan  1 00:00:30           user            warn           kernel: wl0: MAC Address: 00:26:91:20:84:17
      Jan  1 00:00:30           user            warn           kernel: wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0
      Jan  1 00:00:30           user            warn           kernel: dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 
      Jan  1 00:00:30           user            warn           kernel: Cfm has been started to initiate!
      Jan  1 00:00:30           user            warn           kernel: Read Flash: part=[PERSISTENT]
      Jan  1 00:00:30           user            warn           kernel: Read Flash: part=[PERSISTENT]
      Jan  1 00:00:30           user            warn           kernel: PSI has been initiated successfully!
      Jan  1 00:00:30           user            warn           kernel: BcmAdsl_Initialize=0xC0070958, g_pFnNotifyCallback=0xC008E3C4
      Jan  1 00:00:30           user            warn           kernel: AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
      Jan  1 00:00:30           user            warn           kernel: pSdramPHY=0xA0FFFFF8, 0x1B7966 0xDEADBEEF
      Jan  1 00:00:30           user            warn           kernel: AdslCoreSharedMemInit: shareMemAvailable=21568
      Jan  1 00:00:30           user            warn           kernel: AdslCoreHwReset:  AdslOemDataAddr = 0xA0FEF9FC
      Jan  1 00:00:30           user            warn           kernel: AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
      Jan  1 00:00:30           user            warn           kernel: dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 
      Jan  1 00:00:30           user            warn           kernel: ATM proc init !!!
      Jan  1 00:00:30           user            warn           kernel: ATM Config Management initiated successfully!
      Jan  1 00:00:30           user            warn           kernel: ip_tables: (C) 2000-2002 Netfilter core team
      Jan  1 00:00:30           user            warn           kernel: ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
      Jan  1 00:00:30           user            warn           kernel: ip_conntrack_pptp version 2.1 loaded
      Jan  1 00:00:30           user            warn           kernel: ip_nat_pptp version 2.0 loaded
      Jan  1 00:00:30           user            warn           kernel: ip_conntrack_h323: init 
      Jan  1 00:00:30           user            warn           kernel: ip_nat_h323: initialize the module!
      Jan  1 00:00:30           user            warn           kernel: BRCM NAT Caching v0.1 Nov 18 2006 14:56:48
      Jan  1 00:00:30           user            warn           kernel: BRCM NAT Cache: Hooking hit function @ c0058c64
      Jan  1 00:00:30           user            warn           kernel: ip_conntrack_rtsp v0.01 loading
      Jan  1 00:00:30           user            warn           kernel: ip_nat_rtsp v0.01 loading
      Jan  1 00:00:30           user            warn           kernel: Security configuration management initiated successfully!
      Jan  1 00:00:30           user            warn           kernel: Read Flash: part=[FACTORYINFO]
      Jan  1 00:00:30           user            warn           kernel: Enter kerSysFactoryInfoGet: strLen[64],offset[0]
      Jan  1 00:00:30           user            warn           kernel: FactoryInfo[1-10]=[LK93211363]
      Jan  1 00:00:30           user            info           kernel: device eth0 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 1(eth0) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 1(eth0) entering forwarding state
      Jan  1 00:00:30           user            info           kernel: device wl0 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 2(wl0) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 2(wl0) entering forwarding state
      Jan  1 00:00:30           user            info           kernel: device wl0.1 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 3(wl0.1) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 3(wl0.1) entering forwarding state
      Jan  1 00:00:30           user            warn           kernel: hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
      Jan  1 00:00:30           user            warn           kernel:  source->dev->name=[wl0] ,is_local=[0]
      Jan  1 00:00:30           user            info           kernel: device eth0 left promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 1(eth0) entering disabled state
      Jan  1 00:00:30           user            info           kernel: device eth0 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 1(eth0) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 1(eth0) entering forwarding state
      Jan  1 00:00:30           user            info           kernel: device wl0 left promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 2(wl0) entering disabled state
      Jan  1 00:00:30           user            info           kernel: device wl0 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 2(wl0) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 2(wl0) entering forwarding state
      Jan  1 00:00:30           user            warn           kernel: hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
      Jan  1 00:00:30           user            warn           kernel:  source->dev->name=[wl0] ,is_local=[0]
      Jan  1 00:00:30           user            info           kernel: device wl0.1 left promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 3(wl0.1) entering disabled state
      Jan  1 00:00:30           user            info           kernel: device wl0.1 entered promiscuous mode
      Jan  1 00:00:30           user            info           kernel: br0: port 3(wl0.1) entering learning state
      Jan  1 00:00:30           user            info           kernel: br0: topology change detected, propagating
      Jan  1 00:00:30           user            info           kernel: br0: port 3(wl0.1) entering forwarding state
      Jan  1 00:00:30           user            warn           kernel: hlist_add_head_rcu=[0:12:17:41:db:fb]-----------------
      Jan  1 00:00:30           user            warn           kernel:  source->dev->name=[wl0] ,is_local=[0]
      Jan  1 00:00:30           user            warn           kernel: Read Flash: part=[SCRATCH_PAD]
      Jan  1 00:00:30           user            warn           kernel: Read Flash: part=[SCRATCH_PAD]
      Jan  1 00:00:30           user            warn           kernel: Network initiated successfully!
      Jan  1 00:00:31           user            warn           kernel: Web Server initiated successfully!
      Jan  1 00:00:31           user            warn           kernel: Read Flash: part=[SCRATCH_PAD]
      Jan  1 00:00:31           user            warn           kernel: Read Flash: part=[SYSTEM_INI]
      Jan  1 00:00:31           user            warn           kernel: Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
      Jan  1 00:00:31           user            warn           kernel: SystemIni[1-10]=[[quickSetu]
      Jan  1 00:00:31           user            debug          syslog: Remote upgrade: Admin URL is blank, then don't start RemoteAutoUpgradeThread 
      Jan  1 00:00:33           daemon          info           dnsmasq[534]: started, version 2.23 cachesize 150
      Jan  1 00:00:33           daemon          info           dnsmasq[534]: compile time options: no-IPv6 GNU-getopt ISC-leasefile no-DBus
      Jan  1 00:00:33           daemon          warn           dnsmasq[534]: running as root
      Jan  1 00:00:33           daemon          info           dnsmasq[534]: read /etc/hosts - 1 addresses
      Jan  1 00:00:33           daemon          warn           dnsmasq[534]: failed to access /etc/resolv.conf: No such file or directory
      Jan  1 00:00:34           daemon          info           dnsmasq[544]: started, version 2.23 cachesize 150
      Jan  1 00:00:34           daemon          info           dnsmasq[544]: compile time options: no-IPv6 GNU-getopt ISC-leasefile no-DBus
      Jan  1 00:00:34           daemon          warn           dnsmasq[544]: running as root
      Jan  1 00:00:34           daemon          info           dnsmasq[544]: read /etc/hosts - 1 addresses
      Jan  1 00:00:34           daemon          warn           dnsmasq[544]: failed to access /etc/resolv.conf: No such file or directory
      Jan  1 00:00:34           user            info           kernel: br0: port 1(eth0) entering disabled state
      Jan  1 00:00:35           user            warn           kernel: Cfm initiated successfully!
      Jan  1 00:00:50           user            warn           kernel: Read Flash: part=[FACTORYINFO]
      Jan  1 00:00:50           user            warn           kernel: Enter kerSysFactoryInfoGet: strLen[1024],offset[0]
      Jan  1 00:00:50           user            warn           kernel: FactoryInfo[1-10]=[LK93211363]
      Jan  1 00:00:50           user            warn           kernel: Read Flash: part=[PERSISTENT]
      Jan  1 00:00:50           user            warn           kernel: Read Flash: part=[BACKUP]
      Jan  1 00:00:50           user            warn           kernel: Enter kerSysBackupGet: strLen[24576],offset[0],fInfo.flash_backup_blk_offset=[0]
      Jan  1 00:00:50           user            warn           kernel: Backup[1-10]=[<psitree>
      Jan  1 00:00:50           user            warn           kernel: ]
      Jan  1 00:00:50           user            warn           kernel: Enter kerSysScratchPadBlock
      Jan  1 00:00:50           user            warn           kernel: read buffer len is: 4096
      Jan  1 00:00:50           user            warn           kernel: Read Flash: part=[SYSTEM_INI]
      Jan  1 00:00:50           user            warn           kernel: Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
      Jan  1 00:00:50           user            warn           kernel: SystemIni[1-10]=[[quickSetu]

dmesg info:
et = 0x0

system_ini_start_blk = 1017
system_ini_number_blk = 1
system_ini_blk_offset = 0x0
system_ini_length = 4096

fInfo.flash_nvram_start_blk = 0
fInfo.flash_nvram_blk_offset = 0x580
fInfo.flash_nvram_number_blk = 1

fInfo.flash_persistent_start_blk = 1018
fInfo.flash_persistent_blk_offset = 0x0
fInfo.flash_persistent_number_blk = 6

backup_start_blk = 1010
backup_blk_offset = 0x0
backup_number_blk = 6
backup_length = 24576

psi startAddr = bfffa000
systemini startAddr = bfff9000
sp startAddr = bfff8000
backup startAddr = bfff2000

F@ST2604 prom init
CPU revision is: 00029107
Determined physical RAM map:
 memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
  DMA zone: 4000 pages, LIFO batch:1
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 128.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13816k/16000k available (1516k kernel code, 2164k reserved, 232k data, 72k init, 0k highmem)
Calibrating delay loop... 254.77 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Can't analyze prologue code at 80189904
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 20, pci mem c0000b00
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
RestoreMacFilter: Button GPIO 0x21 is enabled
RestoreMacFilter: Button Interrupt 0x1 is enabled
RestoreMacFilter: Interrupt mapping OK
Serial: BCM63XX driver $Revision: 1.3 $
ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
********* ip_rt_init ************
sizeof(struct rtable)=244
ip_rt_max_size=2048, rt_hash_mask=511, ipv4_dst_ops.gc_thresh=512, 
ip_rt_gc_interval=12000, rt_secret_rebuild=120000
TCP: Hash tables configured (established 512 bind 1024)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 72k freed
Algorithmics/MIPS FPU Emulator v1.5
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6348B0 Ethernet Network Device v0.3 Jan 19 2009 17:23:25
Config Ethernet Switch Through SPI Slave Select 0
Cfm wathcer has been setup!
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered 
eth0: MAC Address: 00:26:91:20:84:16
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:26:91:20:84:17
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.174.64.18.cpe1.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 
Cfm has been started to initiate!
Read Flash: part=[PERSISTENT]
Read Flash: part=[PERSISTENT]
PSI has been initiated successfully!
BcmAdsl_Initialize=0xC0070958, g_pFnNotifyCallback=0xC008E3C4
AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA0FFFFF8, 0x1B7966 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=21568
AdslCoreHwReset:  AdslOemDataAddr = 0xA0FEF9FC
AnnexCParam=0x7FFF7858 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 
ATM proc init !!!
ATM Config Management initiated successfully!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (125 buckets, 0 max) - 368 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_conntrack_h323: init 
ip_nat_h323: initialize the module!
BRCM NAT Caching v0.1 Nov 18 2006 14:56:48
BRCM NAT Cache: Hooking hit function @ c0058c64
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
Security configuration management initiated successfully!
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[64],offset[0]
FactoryInfo[1-10]=[LK93211363]
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
 source->dev->name=[wl0] ,is_local=[0]
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device wl0 left promiscuous mode
br0: port 2(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
hlist_add_head_rcu=[2:26:91:20:84:17]-----------------
 source->dev->name=[wl0] ,is_local=[0]
device wl0.1 left promiscuous mode
br0: port 3(wl0.1) entering disabled state
device wl0.1 entered promiscuous mode
br0: port 3(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.1) entering forwarding state
hlist_add_head_rcu=[0:12:17:41:db:fb]-----------------
 source->dev->name=[wl0] ,is_local=[0]
Read Flash: part=[SCRATCH_PAD]
Read Flash: part=[SCRATCH_PAD]
Network initiated successfully!
Web Server initiated successfully!
Read Flash: part=[SCRATCH_PAD]
Read Flash: part=[SYSTEM_INI]
Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
SystemIni[1-10]=[[quickSetu]
br0: port 1(eth0) entering disabled state
Cfm initiated successfully!
Read Flash: part=[FACTORYINFO]
Enter kerSysFactoryInfoGet: strLen[1024],offset[0]
FactoryInfo[1-10]=[LK93211363]
Read Flash: part=[PERSISTENT]
Read Flash: part=[BACKUP]
Enter kerSysBackupGet: strLen[24576],offset[0],fInfo.flash_backup_blk_offset=[0]
Backup[1-10]=[<psitree>
]
Enter kerSysScratchPadBlock
read buffer len is: 4096
Read Flash: part=[SYSTEM_INI]
Enter kerSysSystemIniGet: strLen[4096],offset[0],fInfo.flash_system_ini_blk_offset=[0]
SystemIni[1-10]=[[quickSetu]
SystemIni[1-10]=[[quickSetu]

(Last edited by naplam on 18 Jan 2010, 21:19)

Does it work with Sagem fast 2604?

The discussion might have continued from here.