Hello
I'm connected to this Dockstar serial cable (that I made).
I'm root.
I would like to install Openwrt
I downloaded
openwrt-kirkwood-rootfs.tar.gz
openwrt-kirkwood-uImage
What is the simplest way to do the install?( there are many different suggestions there on the site,I;m not sure to pick the right one)
Here goes the log
-sh-3.2# init 6
BusyBox v1.7.0 (2008-02-26 19:25:17 IST) multi-call binary
Usage: init
Init is the parent of all processes
U-Boot 1.1.4 (Jul 16 2009 - 21:02:16) Cloud Engines (3.4.16)
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 00690D60
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:256 MB
CPU : Marvell Feroceon (Rev 1)
CLOUD ENGINES BOARD: REDSTONE:1.0
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
Reading data from 0x100000 -- 0% complete.
Reading data from 0x107800 -- 1% complete.
...
Reading data from 0x3e8800 -- 97% complete.
Reading data from 0x3f0800 -- 98% complete.
Reading data from 0x3f8000 -- 99% complete.
Reading data from 0x3ff800 -- 100% complete.
3145728 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-08-31 23:31:05 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1976384 Bytes = 1.9 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux............................................................................................................................ done, bootin.
[ 0.000000] Linux version 2.6.22.18 (bdietrich@brad-ux) (gcc version 4.2.1) #57 Mon Aug 31 16:31:01 PDT 2009
[ 0.000000] CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] Machine: Feroceon-KW
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] CPU0: D VIVT write-back cache
[ 0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
[ 0.000000] Built 1 zonelists. Total pages: 32512
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 128MB 0MB 0MB 0MB = 128MB total
[ 0.000000] Memory: 125824KB available (3588K code, 252K data, 120K init)
[ 0.240000] Mount-cache hash table entries: 512
[ 0.240000] CPU: Testing write buffer coherency: ok
[ 0.240000] NET: Registered protocol family 16
[ 0.240000]
[ 0.240000] CPU Interface
[ 0.240000] -------------
[ 0.240000] SDRAM_CS0 ....base 00000000, size 128MB
[ 0.240000] SDRAM_CS1 ....disable
[ 0.240000] SDRAM_CS2 ....disable
[ 0.240000] SDRAM_CS3 ....disable
[ 0.240000] PEX0_MEM ....base e8000000, size 128MB
[ 0.240000] PEX0_IO ....base f2000000, size 1MB
[ 0.240000] INTER_REGS ....base f1000000, size 1MB
[ 0.240000] NFLASH_CS ....base fa000000, size 2MB
[ 0.240000] SPI_CS ....base f4000000, size 16MB
[ 0.240000] BOOT_ROM_CS ....no such
[ 0.240000] DEV_BOOTCS ....no such
[ 0.240000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.240000]
[ 0.240000] Marvell Development Board (LSP Version KW_LSP_4.2.7_patch21_with_rx_desc_tuned)-- SHEEVA PLUG Soc: 88F6281 A0 LE
[ 0.240000]
[ 0.240000] Detected Tclk 200000000 and SysClk 400000000
[ 0.240000] MV Buttons Device Load
[ 0.240000] Marvell USB EHCI Host controller #0: c0537600
[ 0.740000] PEX0 interface detected no Link.
[ 0.740000] PCI: bus0: Fast back to back transfers enabled
[ 0.740000] SCSI subsystem initialized
[ 0.740000] usbcore: registered new interface driver usbfs
[ 0.740000] usbcore: registered new interface driver hub
[ 0.740000] usbcore: registered new device driver usb
[ 0.740000] NET: Registered protocol family 2
[ 0.750000] Time: kw_clocksource clocksource has been installed.
[ 0.840000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.840000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.840000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.840000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.840000] TCP reno registered
[ 0.870000] RTC has been updated!!!
[ 0.870000] RTC registered
[ 0.870000] Use the XOR engines (acceleration) for enhancing the following functions:
[ 0.870000] o RAID 5 Xor calculation
[ 0.870000] o kernel memcpy
[ 0.870000] o kenrel memzero
[ 0.870000] Number of XOR engines to use: 4
[ 0.870000] cesadev_init(c00116b4)
[ 0.870000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 0.870000] MV Buttons Driver Load
[ 0.870000] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 0.870000] squashfs: LZMA suppport for slax.org by jro
[ 0.870000] JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc.
[ 0.870000] io scheduler noop registered
[ 0.870000] io scheduler anticipatory registered (default)
[ 0.890000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[ 0.890000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.900000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
[ 0.900000] RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
[ 0.910000] Loading Marvell Ethernet Driver:
[ 0.920000] o Cached descriptors in DRAM
[ 0.920000] o DRAM SW cache-coherency
[ 0.920000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 0.930000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 0.940000] o TCP segmentation offload enabled
[ 0.940000] o Receive checksum offload enabled
[ 0.940000] o Transmit checksum offload enabled
[ 0.950000] o Network Fast Processing (Routing) supported
[ 0.960000] o Driver ERROR statistics enabled
[ 0.960000] o Driver INFO statistics enabled
[ 0.960000] o Proc tool API enabled
[ 0.970000] o Rx descripors: q0=128
[ 0.970000] o Tx descripors: q0=532
[ 0.980000] o Loading network interface(s):
[ 0.980000] o eth0, ifindex = 1, GbE port = 0
[ 0.990000] o eth1, ifindex = 2, GbE port = 1
[ 0.990000]
[ 1.000000] mvFpRuleDb (c7ed5000): 1024 entries, 4096 bytes
[ 1.000000] Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
[ 1.010000] Copyright (c) 1999-2006 Intel Corporation.
[ 1.010000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
[ 1.020000] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.020000]
[ 1.020000] Warning Sata is Powered Off
[ 1.030000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
[ 1.040000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[ 1.050000] Scanning device for bad blocks
[ 1.070000] Bad eraseblock 305 at 0x02620000
[ 1.150000] Using static partition definition
[ 1.160000] Creating 4 MTD partitions on "nand_mtd":
[ 1.160000] 0x00000000-0x00100000 : "u-boot"
[ 1.170000] 0x00100000-0x00500000 : "uImage"
[ 1.170000] 0x00500000-0x02500000 : "root"
[ 1.180000] 0x02500000-0x10000000 : "data"
[ 1.180000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 1.190000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 1.230000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 1.250000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 1.250000] usb usb1: configuration #1 chosen from 1 choice
[ 1.260000] hub 1-0:1.0: USB hub found
[ 1.260000] hub 1-0:1.0: 1 port detected
[ 1.380000] USB Universal Host Controller Interface driver v3.0
[ 1.660000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 1.810000] usb 1-1: configuration #1 chosen from 1 choice
[ 1.810000] hub 1-1:1.0: USB hub found
[ 1.820000] hub 1-1:1.0: 4 ports detected
[ 2.170000] usb 1-1.2: new high speed USB device using ehci_marvell and address 3
[ 2.270000] usb 1-1.2: configuration #1 chosen from 1 choice
[ 2.270000] usbcore: registered new interface driver usblp
[ 2.280000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 2.290000] Initializing USB Mass Storage driver...
[ 2.290000] scsi0 : SCSI emulation for USB Mass Storage devices
[ 2.300000] usbcore: registered new interface driver usb-storage
[ 2.300000] USB Mass Storage support registered.
[ 2.310000] mice: PS/2 mouse device common for all mice
[ 2.310000] i2c /dev entries driver
[ 2.320000] Linux telephony interface: v1.00
[ 2.320000] md: linear personality registered for level -1
[ 2.330000] md: raid0 personality registered for level 0
[ 2.330000] md: raid1 personality registered for level 1
[ 2.510000] raid6: int32x1 97 MB/s
[ 2.680000] raid6: int32x2 114 MB/s
[ 2.850000] raid6: int32x4 122 MB/s
[ 3.020000] raid6: int32x8 110 MB/s
[ 3.020000] raid6: using algorithm int32x4 (122 MB/s)
[ 3.020000] md: raid6 personality registered for level 6
[ 3.030000] md: raid5 personality registered for level 5
[ 3.030000] md: raid4 personality registered for level 4
[ 3.040000] raid5: measuring checksumming speed
[ 3.090000] arm4regs : 1084.000 MB/sec
[ 3.140000] 8regs : 754.800 MB/sec
[ 3.190000] 32regs : 900.000 MB/sec
[ 3.190000] raid5: using function: arm4regs (1084.000 MB/sec)
[ 3.200000] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
[ 3.200000] dm_crypt using the OCF package.
[ 3.210000] sdhci: Secure Digital Host Controller Interface driver
[ 3.210000] sdhci: Copyright(c) Pierre Ossman
[ 3.220000] usbcore: registered new interface driver usbhid
[ 3.220000] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 3.230000] TCP cubic registered
[ 3.230000] NET: Registered protocol family 1
[ 3.240000] NET: Registered protocol family 17
[ 3.240000] md: Autodetecting RAID arrays.
[ 3.250000] md: autorun ...
[ 3.250000] md: ... autorun DONE.
[ 7.860000] Empty flash at 0x00de8e44 ends at 0x00de9000
[ 8.020000] VFS: Mounted root (jffs2 filesystem) readonly.
[ 8.030000] Freeing init memory: 120K
[ 8.050000] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Blade 1.20 PQ: 0 ANSI: 5
[ 8.160000] sd 0:0:0:0: [sda] 31266816 512-byte hardware sectors (16009 MB)
[ 8.180000] sd 0:0:0:0: [sda] Write Protect is off
[ 8.180000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.380000] sd 0:0:0:0: [sda] 31266816 512-byte hardware sectors (16009 MB)
[ 8.410000] sd 0:0:0:0: [sda] Write Protect is off
[ 8.410000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.420000] sda: sda1 sda2
[ 8.430000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 8.430000] sd 0:0:0:0: Attached scsi generic sg0 type 0
init started: BusyBox v1.7.0 (2008-02-26 19:25:17 IST)
starting pid 286, tty '': '/etc/init.d/rcS'
[ 10.200000] eth0: link down
[ 10.200000] eth0: started
udhcpc (v1.7.0) started
HWADDR 00 0x10 0x75 0x1a 0xd6 0x1b
PIP0 214
PIP1 27
Sending discover...
[ 11.790000] eth0: link up, full duplex, speed 100 Mbps
Sending discover...
Sending discover...
HWADDR 00 0x10 0x75 0x1a 0xd6 0x1b
PIP0 214
PIP1 27
Unexpected Argument: leasefail
interface=eth0
PATH=/sbin:/usr/sbin:/bin:/usr/bin
PWD=/
SHLVL=1
HOME=/
_=/bin/printenv
No lease, forking to background
Loading fs modules: [ 19.400000] fuse init (API version 7.8)
Success
[ 19.780000] ufsd: module license 'Commercial product' taints kernel.
[ 19.940000] ufsd: driver loaded at bf040000 built on Aug 5 2009 15:35:26
[ 19.940000] UFSD version 7.07 (Aug 5 2009, 15:29:19)
[ 19.940000] NTFS read/write support included
[ 19.940000] Hfs+/HfsX read/write support included
[ 19.940000] $Id: ufsdvfs.c,v 1.226 2009/07/30 16:04:07 shura Exp $ (LBD=ON)
Loading tun.ko: [ 19.960000] tun: Universal TUN/TAP device driver, 1.6
[ 19.970000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Success
Loading xce.ko: [ 19.990000] Cloud Engines XCE Init [Version: 1.0.0.20]
[ 20.000000] XCE: CPU MEMORY MAP:
[ 20.000000] XCE: -- 0x00001000 - 0xbeffffff (3055 MB) User Space Mappings
[ 20.010000] XCE: -- 0xbf000000 - 0xbfffffff ( 16 MB) Kernel module space
[ 20.020000] XCE: -- 0xc0000000 - 0xc7ffffff ( 128 MB) Kernel direct-mapped ram
[ 20.020000] XCE: -- 0xc8800000 - 0xe7ffffff ( 504 MB) Kernel vmalloc space
[ 20.030000] XCE: -- 0xe8000000 - 0xfeffffff ( 367 MB) Kernel platform space
[ 20.040000] XCE: Current GPIO State:
[ 20.040000] XCE: GPIO L OUT: 0xeff00000
[ 20.050000] XCE: GPIO L OE: 0xefffffff
[ 20.050000] XCE: GPIO L BLINK: 0x00000000
[ 20.060000] XCE: GPIO L POL: 0x00000000
[ 20.060000] XCE: GPIO L IN: 0xeff00080
[ 20.060000] XCE: GPIO H OUT: 0xfffeffff
[ 20.070000] XCE: GPIO H OE: 0xfffc3fff
[ 20.070000] XCE: GPIO H BLINK: 0x00000000
[ 20.080000] XCE: GPIO H POL: 0x00000000
[ 20.080000] XCE: GPIO H IN: 0x0002fffd
[ 20.090000] XCE: Kernel thread starting PID: 354
Success
[ 20.090000] XCE: -- 'wdog=off
[ 20.090000] '
Starting hbplug: Success
starting pid 356, tty '': '/bin/sh'
-sh-3.2# [ 21.080000] XCE: BLPARAMS: -- Loading properties [c7117f04].
[ 21.090000] XCE: BLPARAMS: reading 2048 bytes @ a0000
[ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a0800
[ 21.100000] XCE: BLPARAMS: reading 2048 bytes @ a1000
[ 21.110000] XCE: BLPARAMS: reading 2048 bytes @ a1800
[ 26.290000] XCE: -- 'led0=0'
-sh-3.2#