Hi, all!
I have DLink DSL-2650U (bcm6358). After little patching Makefile to add 96358VW2 targer, router successfuly flashed by openwrt-96358VW2-squashfs-dsl2650u-cfe.bin.
Index: target/linux/brcm63xx/image/Makefile
===================================================================
--- target/linux/brcm63xx/image/Makefile (revision 19253)
+++ target/linux/brcm63xx/image/Makefile (working copy)
@@ -163,6 +163,8 @@
$(call Image/Build/CFE,$(1),F@ST2404,6348,bc310,OpenWRT-$(REVISION),bc310)
# Inventel Livebox
$(call Image/Build/RedBoot,livebox)
+ # D-Link DSL-2650U
+ $(call Image/Build/CFE,$(1),96358VW2,6358,bc310,,dsl2650u)
# D-Link DSL-2740B
$(call Image/Build/CFE,$(1),96358GW,6358,bc310,,dsl2740b)
# Pirelli Alice Gate VoIP 2 Plus Wi-Fi AGPF-S0
Here is startup log:
CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)
Build Date: Tue Apr 24 15:57:24 CST 2007 (gavin@FD5)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MB, id 0x2200, size 8192KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80527C50 (1207376)
Initialized Data: 0x8041D580 - 0x8041F480 (7936)
BSS Area: 0x8041F480 - 0x80425C50 (26576)
Local Heap: 0x80425C50 - 0x80525C50 (1048576)
Stack Area: 0x80525C50 - 0x80527C50 (8192)
Text (code) segment: 0x80401000 - 0x8041D57C (116092)
Boot area (physical): 0x00528000 - 0x00568000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.2
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name :
Default host flash file name : openwrt-96358VW2-squashfs-dsl2650u-cfe.bin
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:22:b0:xx:xx:xx
PSI Size (1-64) KBytes : 24
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.30.10 (tipok@mythbox) (gcc version 4.3.3 (GCC) ) #2 Thu Jan 21 16:01:38 EET 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300000000 Hz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.1
console [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29512k/32768k available (2073k kernel code, 3256k reserved, 428k data, 132k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
net_namespace: 532 bytes
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.306:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) ?© 2001-2006 Red Hat, Inc.
msgmni has been set to 57
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console handover: boot [early0] -> real [ttyS0]
bcm63xx_enet MII bus: probed
bcm963xx_flash: 0x02000000 at 0x1e000000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc310.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 700000
bcm963xx_flash: Partition 3 is nvram offset 7f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 7e0000
bcm963xx_flash: Spare partition is 260000 offset and length 590000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-oy
0x0000000f0000-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=260000, len=590000
0x000000260000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "nvram"
0x000000010000-0x0000007f0000 : "linux"
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
Registered led device: <NULL>
leds-gpio: probe of leds-gpio.0 failed with error -16
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 132k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press CTRL-C for failsafe
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
- init -
Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
eth1: link forced UP - 100/full - flow control off/off
device eth1 entered promiscuous mode
br-lan: port 1(eth1) entering forwarding state
Generic kernel compatibility enabled based on linux-next next-20100113
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: Failed to enable switch
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 8
NET: Registered protocol family 20
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (512 buckets, 2048 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
This device also have 1 additional USB and 5th ethernet port (it goes into broadcom main cpu) on pcb, but connectors are not soldered.
openwrt on Dlink DSL-2650U more -> http://tipok.org.ua/ru/node/31