Topic: help me , who has DIR-825 B1 bootloader?
i have one DIR-825.
but this 825 user u-boot bootloader,
Serial can't input .
but i wan't use OPENWRT , so need can be input bootloader.
thanks . ![]()
DDNAS info site: www.rtnas.com
OpenWrt → General Discussion → help me , who has DIR-825 B1 bootloader?
i have one DIR-825.
but this 825 user u-boot bootloader,
Serial can't input .
but i wan't use OPENWRT , so need can be input bootloader.
thanks . ![]()
my dir-825 console has been disabled.....
I need to re-flash with the J-TAG as the backup loader is gone.
check out this page.
http://fetzig.org/2009/12/24/openwrt-on … k-dir-825/
and don't confuse file name. there are three version on dir-825 firmware.
openwrt-ar71xx-generic-dir-825-b1-jffs2-backup-..>
openwrt-ar71xx-generic-dir-825-b1-jffs2-factory..>
openwrt-ar71xx-generic-dir-825-b1-jffs2-sysupgr..>
in that page, you need to use backup version.
try it.
check out this page.
http://fetzig.org/2009/12/24/openwrt-on … k-dir-825/
and don't confuse file name. there are three version on dir-825 firmware.
openwrt-ar71xx-generic-dir-825-b1-jffs2-backup-..>
openwrt-ar71xx-generic-dir-825-b1-jffs2-factory..>
openwrt-ar71xx-generic-dir-825-b1-jffs2-sysupgr..>in that page, you need to use backup version.
try it.
thanks
i just try.
can't upgrade.
any bin display this message(include DD-WRT, d-link(ww,na):
UPLOAD FAILED
The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this Gateway, or the uploaded file may be corrupted.
If the uploaded file is correct, it is possible that the gateway may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a "user" instead of an "admin" - only administrators can upload new firmware.
The Gateway will not be reprogrammed.
I googled it. and I got this page.
http://www.dd-wrt.com/phpBB2/viewtopic. … f3053b8306
"I tried 30/30/30, restore-factory-defaults, flashing to 14144, flashing to stock (wireless AP works here) and back to 13972. No luck.
Immediately after a restore-defaults or 30/30/30, the dd-wrt SSID is visible. Changing it to client bridge, adding a virtual interface, or changing the SSID (i.e., changing any setting) leaves me with complete wireless nonfunction.
If only the stock firmware had client bridge mode.
I also tried OpenWRT briefly. That adventure almost left my router bricked, but taught me a perhaps-useful lesson. If your hold-reset-for-30 seconds firmware bootloader isn't working at all, try powercycling and holding the reset button as it turns on. This was the trick that allowed me to flash OpenWRT off.
"
please try powercycling way and 30-30-30 reset way.
thanks nikescar
this message maybe can't for me.
that DIR825 can be flash DD-WRT.
my DIR-825 can't flash DD-WRT. default bin is 2.0SS. this version only for taiwan(china).
i‘m Crazey??????
thanks nikescar
this message maybe can't for me.
that DIR825 can be flash DD-WRT.
my DIR-825 can't flash DD-WRT. default bin is 2.0SS. this version only for taiwan(china).
i‘m Crazey??????
Here is full flash image of DIR-825 B2 WW, (bootloader is working with WEB rescue console), http://upload.com.ua/get/901919492/
Made with SPIPGM http://rayer.ic.cz/programm/programm.htm#SPIPGM
Interface via LPT here http://rayer.ic.cz/elektro/spipgm.htm
I'm not able to download it from http://upload.com.ua/get/901919492/
Can you upload it to an other service?
Thank you
thank you, vavasik. ![]()
OpenWrt → General Discussion → help me , who has DIR-825 B1 bootloader?
Powered by PunBB, supported by Informer Technologies, Inc.