OpenWrt Forum Archive

Topic: Running Kamikaze on Linksys wag160n

The content of this topic has been archived between 7 Oct 2014 and 12 Apr 2018. Unfortunately there are posts – most likely complete pages – missing.

Hi,

does kamikaze run on Linksys WAG160N?
If yes can someone point me to a useful howto link?
Thanks in advance
Dick

(Last edited by x345r on 31 Mar 2009, 22:24)

Hi
will someone post cfe /wholeflash jtag dump of wag160n version1 annex A device please?

thanks in advance

hello,

same here, flash or some kind of howto would be nice
thanks and regards.

up

brcm63xx seems to be supported since backfire.

http://wiki.openwrt.org/toh/linksys/wag160n


Is there a method to do the operation without jtag cable?

And what is the correct image to choose

I've been waiting for this for some time. However I've tried various images via the web interface and none of them are accepted. What is the correct image for the WAG160N (my version is the Annex A).

And there is this on the hardware page:

"Hints

Before flashing OpenWrt make sure to backup "ath_data" (/dev/mtdblock4). It's calibration data for wireless device. You have to include this data into OpenWrt, and modify ath9k driver to read it durning device initialisation."

How on earth is this to be done? I have installed a firmware to give me telnet access and used the webserver to download all the /dev/mtdblockX contents, but I'm now stuck.

Here are some pertinent command outputs:

# cat /proc/cpuinfo
system type             : 96358GW
processor               : 0
cpu model               : BCM6358 V1.0
BogoMIPS                : 299.82
wait instruction        : no
microsecond timers      : yes
tlb_entries             : 32
extra interrupt vector  : no
hardware watchpoint     : no
unaligned access                : 446889
VCED exceptions         : not available
VCEI exceptions         : not available

# free
              total         used         free       shared      buffers
  Mem:        29364        22320         7044            0         1732
Swap:            0            0            0
Total:        29364        22320         7044

# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/mtdblock0            2624      2624         0 100% /
# dmesg                                                               
conntrack_pptp version 2.1 loaded                                     
ip_conntrack_rtsp v0.01 loading                                       
ip_nat_h323: init success                                             
ip_nat_pptp version 2.0 loaded                                         
ip_nat_rtsp v0.01 loading                                             
ip_tables: (C) 2000-2002 Netfilter core team                           
netfilter PSD loaded - (c) astaro AG                                   
ipt_random match loaded                                               
NET: Registered protocol family 1                                     
NET: Registered protocol family 17                                     
Ebtables v2.0 registered                                               
NET: Registered protocol family 8                                     
NET: Registered protocol family 20                                     
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>         
All bugs added by David S. Miller <davem@redhat.com>                   
VFS: Mounted root (squashfs filesystem) readonly.                     
Freeing unused kernel memory: 92k freed                               
Algorithmics/MIPS FPU Emulator v1.5                                   
bcm_enet: module license 'Proprietary' taints kernel.                 
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jun  3 2009 12:25:20   
Config Ethernet Switch Through MDIO Pseudo PHY Interface               
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered                 
eth0: MAC Address: 00:22:6B:E2:5F:9A                                   
BcmAdsl_Initialize=0x8011A498, g_pFnNotifyCallback=0x8021F624         
AnnexCParam=0x7FFF7ED8 AnnexAParam=0x00000980 adsl2=0x00000000         
pSdramPHY=0xA1FFFFF8, 0x1B7F1F 0xDEADBEEF                             
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4                         
AnnexCParam=0x7FFF7ED8 AnnexAParam=0x00000980 adsl2=0x00000000         
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered                 
AnnexCParam=0x7FFF7EC8 AnnexAParam=0x00000980 adsl2=0x00000000         
ATM proc init !!!                                                     
device eth0 entered promiscuous mode                                   
eth0 Link UP.                                                         
br0: port 1(eth0) entering learning state                             
br0: topology change detected, propagating                             
br0: port 1(eth0) entering forwarding state                           
kwsc_mod: init                                                         
create wsc_cfb entry                                                   
create wsc_cfb entry                                                   
create wsc_iechange entry                                             
create wsc_userset entry                                               
ath_dfs: Version 2.0.0                                                 
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_hal: 0.9.14.25 (AR5416, DEBUG)                                     
wlan: 0.8.4.2 (Atheros/multi-bss)                                       
ath_rate_atheros: Version 2.0.1                                         
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)                                   
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)                       
Changelist :0 Date: 0                                                   
Chan  Freq  RegPwr  HT   CTL CTL_U CTL_L DFS                           
   1  2412n     27  HT20  1    0    1     N                             
   1  2412n     20  HT40  1    0    1     N                             
   2  2417n     20  HT40  1    0    1     N                             
   3  2422n     20  HT40  1    1    1     N                             
   4  2427n     20  HT40  1    1    1     N                             
   5  2432n     20  HT40  1    1    1     N                             
   6  2437n     20  HT40  1    1    1     N                             
   7  2442n     20  HT40  1    1    1     N                             
   8  2447n     20  HT40  1    1    1     N                             
   9  2452n     20  HT40  1    1    1     N                             
  10  2457n     20  HT40  1    1    1     N                             
  11  2462n     20  HT40  1    1    1     N                             
  12  2467n     20  HT40  1    1    0     N                             
  13  2472n     20  HT40  1    1    0     N                             
ath_attach 9864val 1ce00                                               
wifi0: 11ng rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11ng MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15                                           
wifi0: mac 13.2 phy 8.1 radio 15.0                                                                 
wifi0: Use hw queue 1 for WME_AC_BE traffic                                                       
wifi0: Use hw queue 0 for WME_AC_BK traffic                                                       
wifi0: Use hw queue 2 for WME_AC_VI traffic                                                       
wifi0: Use hw queue 3 for WME_AC_VO traffic                                                       
wifi0: Use hw queue 8 for CAB traffic                                                             
wifi0: Use hw queue 9 for beacons                                                                 
wifi0: Atheros 5416 Owl emulation: mem=0x10000000, irq=39 hw_base=0xb0000000                       
ar5416SetPowerPerRateTable() syn 2412 ctl 2412 ext 2412 is40 0                                     
  6mb OFDM  15.0 dBm |  9mb OFDM  15.0 dBm | 12mb OFDM  15.0 dBm | 18mb OFDM  15.0 dBm             
24mb OFDM  15.0 dBm | 36mb OFDM  15.0 dBm | 48mb OFDM  15.0 dBm | 54mb OFDM  14.0 dBm             
1L   CCK   17.0 dBm | 2L   CCK   17.0 dBm | 2S   CCK   17.0 dBm | 5.5L CCK   17.0 dBm             
5.5S CCK   17.0 dBm | 11L  CCK   17.0 dBm | 11S  CCK   17.0 dBm | XR         15.0 dBm             
HT20mcs 0  14.0 dBm | HT20mcs 1  14.0 dBm | HT20mcs 2  14.0 dBm | HT20mcs 3  14.0 dBm             
HT20mcs 4  14.0 dBm | HT20mcs 5  14.0 dBm | HT20mcs 6  13.0 dBm | HT20mcs 7  11.0 dBm             
HT40mcs 0   0.0 dBm | HT40mcs 1   0.0 dBm | HT40mcs 2   0.0 dBm | HT40mcs 3   0.0 dBm             
HT40mcs 4   0.0 dBm | HT40mcs 5   0.0 dBm | HT40mcs 6   0.0 dBm | HT40mcs 7   0.0 dBm             
Dup CCK     0.0 dBm | Dup OFDM    0.0 dBm | Ext CCK     0.0 dBm | Ext OFDM    0.0 dBm             
2xAntennaReduction: 6, 2xMaxRegulatory: 54, 2xPowerLimit: 60                                       
2xMaxPowerLevel: 28 (HT20)                                                                         
TPC Enabled 1 1 0                                                                                 
ar5416SetPowerPerRateTable() syn 2412 ctl 2412 ext 2412 is40 0                                     
  6mb OFDM  15.0 dBm |  9mb OFDM  15.0 dBm | 12mb OFDM  15.0 dBm | 18mb OFDM  15.0 dBm             
24mb OFDM  15.0 dBm | 36mb OFDM  15.0 dBm | 48mb OFDM  15.0 dBm | 54mb OFDM  14.0 dBm             
1L   CCK   17.0 dBm | 2L   CCK   17.0 dBm | 2S   CCK   17.0 dBm | 5.5L CCK   17.0 dBm             
5.5S CCK   17.0 dBm | 11L  CCK   17.0 dBm | 11S  CCK   17.0 dBm | XR         15.0 dBm             
HT20mcs 0  14.0 dBm | HT20mcs 1  14.0 dBm | HT20mcs 2  14.0 dBm | HT20mcs 3  14.0 dBm             
HT20mcs 4  14.0 dBm | HT20mcs 5  14.0 dBm | HT20mcs 6  13.0 dBm | HT20mcs 7  11.0 dBm             
HT40mcs 0   0.0 dBm | HT40mcs 1   0.0 dBm | HT40mcs 2   0.0 dBm | HT40mcs 3   0.0 dBm             
HT40mcs 4   0.0 dBm | HT40mcs 5   0.0 dBm | HT40mcs 6   0.0 dBm | HT40mcs 7   0.0 dBm             
Dup CCK     0.0 dBm | Dup OFDM    0.0 dBm | Ext CCK     0.0 dBm | Ext OFDM    0.0 dBm             
2xAntennaReduction: 6, 2xMaxRegulatory: 54, 2xPowerLimit: 60                                       
2xMaxPowerLevel: 30 (LEG)                                                                         
device ath0 entered promiscuous mode                                                               
ar5416SetPowerPerRateTable() syn 2412 ctl 2412 ext 2412 is40 0                                     
  6mb OFDM  15.0 dBm |  9mb OFDM  15.0 dBm | 12mb OFDM  15.0 dBm | 18mb OFDM  15.0 dBm             
24mb OFDM  15.0 dBm | 36mb OFDM  15.0 dBm | 48mb OFDM  15.0 dBm | 54mb OFDM  14.0 dBm             
1L   CCK   17.0 dBm | 2L   CCK   17.0 dBm | 2S   CCK   17.0 dBm | 5.5L CCK   17.0 dBm             
5.5S CCK   17.0 dBm | 11L  CCK   17.0 dBm | 11S  CCK   17.0 dBm | XR         15.0 dBm             
HT20mcs 0  14.0 dBm | HT20mcs 1  14.0 dBm | HT20mcs 2  14.0 dBm | HT20mcs 3  14.0 dBm             
HT20mcs 4  14.0 dBm | HT20mcs 5  14.0 dBm | HT20mcs 6  13.0 dBm | HT20mcs 7  11.0 dBm             
HT40mcs 0   0.0 dBm | HT40mcs 1   0.0 dBm | HT40mcs 2   0.0 dBm | HT40mcs 3   0.0 dBm             
HT40mcs 4   0.0 dBm | HT40mcs 5   0.0 dBm | HT40mcs 6   0.0 dBm | HT40mcs 7   0.0 dBm
Dup CCK     0.0 dBm | Dup OFDM    0.0 dBm | Ext CCK     0.0 dBm | Ext OFDM    0.0 dBm
2xAntennaReduction: 6, 2xMaxRegulatory: 54, 2xPowerLimit: 60
2xMaxPowerLevel: 28 (HT20)
TPC Enabled 1 1 0
Force rf_pwd_icsyndiv to 1 on 2412 (1 2)
ath_newstate: Resetting VAP dfswait_run
ath_newstate: Resetting VAP dfswait_run
ar5416SetPowerPerRateTable() syn 2432 ctl 2422 ext 2442 is40 1
  6mb OFDM  17.0 dBm |  9mb OFDM  17.0 dBm | 12mb OFDM  17.0 dBm | 18mb OFDM  17.0 dBm
24mb OFDM  17.0 dBm | 36mb OFDM  17.0 dBm | 48mb OFDM  16.0 dBm | 54mb OFDM  14.0 dBm
1L   CCK   19.0 dBm | 2L   CCK   19.0 dBm | 2S   CCK   19.0 dBm | 5.5L CCK   19.0 dBm
5.5S CCK   19.0 dBm | 11L  CCK   19.0 dBm | 11S  CCK   19.0 dBm | XR         17.0 dBm
HT20mcs 0  18.0 dBm | HT20mcs 1  18.0 dBm | HT20mcs 2  18.0 dBm | HT20mcs 3  18.0 dBm
HT20mcs 4  18.0 dBm | HT20mcs 5  17.0 dBm | HT20mcs 6  13.0 dBm | HT20mcs 7  11.0 dBm
HT40mcs 0  11.0 dBm | HT40mcs 1  11.0 dBm | HT40mcs 2  11.0 dBm | HT40mcs 3  11.0 dBm
HT40mcs 4  11.0 dBm | HT40mcs 5  11.0 dBm | HT40mcs 6  11.0 dBm | HT40mcs 7  11.0 dBm
Dup CCK    11.0 dBm | Dup OFDM   11.0 dBm | Ext CCK    19.0 dBm | Ext OFDM   17.0 dBm
2xAntennaReduction: 0, 2xMaxRegulatory: 40, 2xPowerLimit: 60
2xMaxPowerLevel: 22 (HT40)
TPC Enabled 1 1 0
Force rf_pwd_icsyndiv to 2 on 2432 (1 2)
ath_chan_set: Changing to channel 2422, Flags 30080, PF 0
ieee80211_beacon_alloc[329] : Doing IE to Local
make a wpa2 ie :
30      1c      01      00      00      0f      ac      02      02      00      00      0f      ac      04      00      0f
ac      02      02      00      00      0f      ac      01      00      0f      ac      02      00      00
make a wpa ie :
dd      1e      00      50      f2      01      01      00      00      50      f2      02      02      00      00      50
f2      04      00      50      f2      02      02      00      00      50      f2      01      00      50      f2      02

br0: port 2(ath0) entering learning state
br0: topology change detected, propagating
br0: port 2(ath0) entering forwarding state
ath_aggr_addba_responseprocess: TX ADDBA Response TID: 0  RXBAW: 64 MYBAW: 64 ETHER:00:02:6f:4f:86:1f

(Last edited by alexcrow on 15 Apr 2010, 17:00)

bump

Seems like no-one cares about this router due to its bad reputation with the stock firmware.

I am stuck at the same point..

Before flashing OpenWrt make sure to backup "ath_data" (/dev/mtdblock4). It's calibration data for wireless device. You have to include this data into OpenWrt, and modify ath9k driver to read it durning device initialisation."

Anyone able to assist?

i too have the same problem

looks like maybe it isn't supported as of 10.03 after all

on the wiki page the user managed to make it working by the looks of it

Hi!

Here you can download firmware i've prepared for WAG160N as described on wiki. It's based on Backfire 10.03-rc1 and works well for me since two months now.

--
Regards

thanks. does it also work with the dsl modem?

> thanks. does it also work with the dsl modem?

No. It does not - dsl drivers are missing :-(

Virus wrote:

> thanks. does it also work with the dsl modem?

No. It does not - dsl drivers are missing :-(

Hi Virus,
one question... dsl drivers missing means that wag160n only functions as access point or bridge? So it can't be used as standalone modem/router like original firmware?

Thanks...

Virus,

Can you please re-upload the firmware file for me? The rapidshare limit has expired.

Many thanks

Alex

Here you are, alexcrow :-)

Thx for reup. Is there a way to flash it without jtag?

Thats my issue with ur .bin:
Upgrade file is not the correct type or version for this device.
Upgrade failed.

Please select the correct file and try again.

(Last edited by xris on 13 Jun 2010, 10:54)

biohazard wrote:
Virus wrote:

> thanks. does it also work with the dsl modem?

No. It does not - dsl drivers are missing :-(

Hi Virus,
one question... dsl drivers missing means that wag160n only functions as access point or bridge? So it can't be used as standalone modem/router like original firmware?

Will appreciate an answer to this with an attachment of the /etc/config/network and /etc/config/wireless files to show how it's configured as an AP or bridge (preference).

hi virus
         is it possible to get a dump of wholefalsh /cfe from wag160n?.Need em to debrick mine.
thanks

I only have a serial console on mine, I don't think I can do it from that.

The firmware on here still gives me a 'Kernel panic - not syncing: unable to detect bcm963xx board' error.

Are there any settings in cfe that need changing first?

(Last edited by Zhadnost on 18 Jun 2010, 09:25)

After changing the Board ID to 96358VW, the kernel gets a bit further before falling over.

CFE version 1.0.37-5.4 for BCM96358 (32bit,SP,BE)
Build Date: å 10 19:25:21 CST 2008 (root@9DavidZhang2)
Copyright (C) 2000-2005 Broadcom Corporation.

Boot Address 0xbfc00000

Initializing Arena.
Initializing Devices.
Parallel flash device: name MX29LV320AB, id 0x22a8, size 4096KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80528800 (1210368)
Initialized Data:          0x8041E550 - 0x8041FF60 (6672)
BSS Area:                  0x8041FF60 - 0x80426800 (26784)
Local Heap:                0x80426800 - 0x80526800 (1048576)
Stack Area:                0x80526800 - 0x80528800 (8192)
Text (code) segment:       0x80401000 - 0x8041E544 (120132)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 2
Board Id Name                     : 96358VW
Psi size in KB                    : 24
Number of MAC Addresses (1-32)    : 10
Base MAC Address                  : 00:1d:7e:b5:0f:92
Ethernet PHY Type                 : Internal
Memory size in MB                 : 32
CMT Thread Number                 : 1

*** Press any key to stop auto run (2 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.10 (openwrt@wrt1.marcant.net) (gcc version 4.3.3 (GCC) ) #8 Thu Apr 1 10:20:02 CEST 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-5.4
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29544k/32768k available (2135k kernel code, 3224k reserved, 458k data, 140k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0:   IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0:   IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0:   MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.228:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW, and tagid bc310.
bcm963xx_flash: Partition 0 is CFE offset 81c6ba20 and length 0
bcm963xx_flash: Partition 1 is kernel offset e84 and length 0
bcm963xx_flash: Partition 2 is rootfs offset ec5 and length 0
bcm963xx_flash: Partition 3 is nvram offset f06 and length 0
bcm963xx_flash: Partition 4 is linux offset f46 and length 0
bcm963xx_flash: Spare partition is 3c0000 offset and length 30000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
split_squashfs: no squashfs found in "bcm963xx"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl-fail
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Node at 0x0000f6bc with length 0x00000a8f would run over the end of the erase block
Perhaps the file system was created with the wrong erase size?
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000f6c4: 0x52b6 instead

<snip='Lots of the Above'>

jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x002b0024: 0x683a instead
Further such events for this erase block will not be printed
VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
Kernel panic - not syncing: Attempted to kill init!

(Last edited by Zhadnost on 18 Jun 2010, 09:43)

Okay that's weird, I just erased and re-installed the image and it appears to have worked.

Another odd thing, is that the rootfs is so small that I can't put openvpn on it, I know I've managed to stuff it into a 4MB flash before.

And the only image I can get to install is openwrt-96358GW-squashfs-bc310-cfe.bin , which I have no idea where I got it from.

KAMIKAZE (bleeding edge, r20018)

(Last edited by Zhadnost on 18 Jun 2010, 12:00)

Can u upload it?

Zhadnost wrote:

Okay that's weird, I just erased and re-installed the image and it appears to have worked.

Another odd thing, is that the rootfs is so small that I can't put openvpn on it, I know I've managed to stuff it into a 4MB flash before.

And the only image I can get to install is openwrt-96358GW-squashfs-bc310-cfe.bin , which I have no idea where I got it from.

KAMIKAZE (bleeding edge, r20018)

I've searched image openwrt-96358GW-squashfs-bc310-cfe.bin in web but found nothing... is this image ok ?
With this image asdl works fine?
Please can u share image?

Thanks !!!!