Originally(2yrs ago) I know Breaker Barrier worked but no wifi, also it makes the unit very hot and I had to remove it, I figured I'd give it try except with 15.05.1 cause I wanted to try the kmod-brcmfmac and mess with it a bit, but if that didn't work i hoped that it wouldn't make it for routing at least and hoped that it doesn't get hot any more? but the CC image failed to load. In order to rule out a bad download, i downloaded another, flashed that image with same results, so i was able to recover ran but it was bricked again, i did reset to defaults on the linksys-E3200 I was able to recover still but wanted to post this, since the dev ticket site didn't let me create an account to report this bug or miscellaneous problem.
Side note, the BB 14.04 looks to have 6 partitions with only one nvram, I'll have to add that one here in a moment since I still have it on the router.
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
BusyBox v1.23.2 (2016-03-01 08:50:41 CET) built-in shell (ash)
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (15.05.1, r48532)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
================= FAILSAFE MODE active ================
special commands:
* firstboot reset settings to factory defaults
* mount_root mount root-partition with config files
after mount_root:
* passwd change root's password
* /etc/config directory with config files
for more help see:
http://wiki.openwrt.org/doc/howto/generic.failsafe
=======================================================
root@(none):/# dmesg
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48532) ) #1 Tue Mar 1 09:17:19 CET 2016
[ 0.000000] CPU0 revision is: 00019749 (MIPS 74Kc)
[ 0.000000] bcm47xx: Using bcma bus
[ 0.000000] bcma: bus0: Found chip with id 0x5357, rev 0x02 and package 0x0A
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802e4300, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61392K/65536K available (2594K kernel code, 119K rwdata,324K rodata, 148K init, 288K bss, 4144K reserved, 0K highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev0x26, class 0x0)
[ 0.000000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev0x1C, class 0x0)
[ 0.000000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
[ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x04, class 0x0)
[ 0.000000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x05, class 0x0)
[ 0.000000] bcma: bus0: Core 5 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x02, class 0x0)
[ 0.000000] bcma: bus0: Core 6 found: I2S (manuf 0x4BF, id 0x834, rev 0x02, class 0x0)
[ 0.000000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x0B, class 0x0)
[ 0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28A42A09)
[ 0.000000] bcma: bus0: Found serial flash
[ 0.000000] bcma: bus0: Found M25FL128 serial flash (size: 16384KiB, blocksize: 0x10000, blocks: 256)
[ 0.000000] bcma: bus0: Early bus registered
[ 0.000000] MIPS: machine is Linksys E3200 V1
[ 0.000000] bcm47xx: Setting up vectored interrupts
[ 0.060000] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] Switched to clocksource MIPS
[ 0.090000] NET: Registered protocol family 2
[ 0.090000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.090000] TCP: reno registered
[ 0.090000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.090000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.090000] NET: Registered protocol family 1
[ 0.090000] PCI: CLS 0 bytes, default 32
[ 0.370000] bcma: bus0: Using SPROM revision 8 provided by platform.
[ 0.370000] bcma: bus0: PMU resource config unknown or not needed for device 0x5357
[ 0.370000] bcma: bus0: Workarounds unknown or not needed for device 0x5357
[ 0.370000] bcma: bus0: Initializing MIPS core...
[ 0.370000] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[ 0.370000] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[ 0.370000] bcma: bus0: set_irq: core 0x0819, irq 5 => 5
[ 0.370000] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[ 0.370000] bcma: bus0: set_irq: core 0x0834, irq 2 => 2
[ 0.370000] bcma: bus0: IRQ reconfiguration done
[ 0.370000] bcma: core 0x0800, irq : 2(S)* 3 4 5 6 D I
[ 0.370000] bcma: core 0x0812, irq : 2(S) 3* 4 5 6 D I
[ 0.370000] bcma: core 0x082d, irq : 2(S) 3 4* 5 6 D I
[ 0.370000] bcma: core 0x082c, irq : 2(S) 3 4 5 6 D I*
[ 0.370000] bcma: core 0x0819, irq : 2(S) 3 4 5* 6 D I
[ 0.370000] bcma: core 0x082e, irq : 2(S) 3 4 5 6 D* I
[ 0.370000] bcma: core 0x0834, irq : 2(S)* 3 4 5 6 D I
[ 0.370000] bcma: core 0x080e, irq : 2(S) 3 4 5 6 D I*
[ 0.380000] bcma: bus0: Bus registered
[ 0.380000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.390000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.390000] msgmni has been set to 119
[ 0.390000] io scheduler noop registered
[ 0.390000] io scheduler deadline registered (default)
[ 0.390000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.400000] console [ttyS0] disabled
[ 0.420000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2, base_baud = 1250000) is a U6_16550A
[ 0.790000] console [ttyS0] enabled
[ 0.860000] 7 bcm47xxpart partitions found on MTD device bcm47xxsflash
[ 0.870000] Creating 7 MTD partitions on "bcm47xxsflash":
[ 0.880000] 0x000000000000-0x000000040000 : "boot"
[ 0.880000] 0x000000040000-0x000000fe0000 : "firmware"
[ 0.890000] 0x00000004001c-0x00000004090c : "loader"
[ 0.900000] 0x00000004090c-0x000000147800 : "linux"
[ 0.900000] 0x000000147800-0x000000fe0000 : "rootfs"
[ 0.910000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.910000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.920000] 0x000000370000-0x000000fe0000 : "rootfs_data"
[ 0.930000] 0x000000fe0000-0x000000ff0000 : "nvram"
[ 0.930000] 0x000000ff0000-0x000001000000 : "nvram"
[ 0.940000] bgmac bcma0:2: Found PHY addr: 30 (NOREGS)
[ 0.950000] bgmac bcma0:2: Support for Roboswitch not implemented
[ 0.970000] libphy: bgmac mii bus: probed
[ 1.130000] b53_common: found switch: BCM53125, rev 4
[ 1.140000] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 1.150000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[ 1.150000] TCP: cubic registered
[ 1.160000] NET: Registered protocol family 17
[ 1.160000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.180000] Bridge firewalling registered
[ 1.180000] 8021q: 802.1Q VLAN Support v1.8
[ 1.190000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.200000] Freeing unused kernel memory: 148K (802fb000 - 80320000)
[ 2.340000] init: Console is alive
[ 2.340000] init: - watchdog -
[ 4.400000] init: - preinit -
[ 4.920000] random: procd urandom read with 7 bits of entropy available
[ 6.180000] eth0: Link is Up - 1Gbps/Full - flow control off
[ 77.970000] random: nonblocking pool is initialized
root@(none):/#
root@(none):/# cat /proc/mtd
dev: size erasesize name
mtd0: 00040000 00010000 "boot"
mtd1: 00fa0000 00010000 "firmware"
mtd2: 000008f0 000008f0 "loader"
mtd3: 00106ef4 00010000 "linux"
mtd4: 00e98800 00010000 "rootfs"
mtd5: 00c70000 00010000 "rootfs_data"
mtd6: 00010000 00010000 "nvram"
mtd7: 00010000 00010000 "nvram"
If there is someone that would work on this or check on this that would be Great, Thank you, freeman01
(Last edited by freeman01 on 21 Apr 2017, 21:44)