Topic: Ubiquiti UniFi AP-LR

Hello.
I have BZ.qca9342.v3.7.19.5372.161007.0916 and I want install openWRT in my device, but after this command

fwupdate.real -m openwrt-ar71xx-generic-ubnt-unifi-squashfs-factory.bin -d

I see

BZ.v3.7.19# fwupdate.real -m fwupdate.bin -d 
Found mtd block: /dev/mtd0(u-boot)
Found mtd block: /dev/mtd1(u-boot-env)
Found mtd block: /dev/mtd2(kernel)
Found mtd block: /dev/mtd3(cfg)
Found mtd block: /dev/mtd4(EEPROM)
Got U-Boot variable: mtdparts = mtdparts=mtdparts=ath-nor0:384k(u-boot),64k(u-boot-env),7424k(kernel),256k(cfg),64k(EEPROM)
Adding U-Boot partition: u-boot 9F000000 00060000
Adding U-Boot partition: u-boot-env 9F060000 00010000
Adding U-Boot partition: kernel 9F070000 00740000
Adding U-Boot partition: cfg 9F7B0000 00040000
Adding U-Boot partition: EEPROM 9F7F0000 00010000
Calculating flash size:
Adding block: /dev/mtd0("u-boot") - size: 00060000
Adding block: /dev/mtd1("u-boot-env") - size: 00010000
Adding block: /dev/mtd2("kernel") - size: 00740000
Adding block: /dev/mtd3("cfg") - size: 00040000
Adding block: /dev/mtd4("EEPROM") - size: 00010000
Total flash size: 00800000
Flash start: 9F000000
Flash end: 9F800000
Header MAGIC 'OPEN'
Current: BZ.qca9342.v3.7.19.5372.161007.0916

New ver: BZ.ar934x.v6.0.0-OpenWrt-50104
Invalid version 'BZ.ar934x.v6.0.0-OpenWrt-50104'

After cnhange Chip name to ar934x anr recompile openWRT
I got new error

BZ.v3.7.19# fwupdate.real -m openwrt-qca93xx-generic-ubnt-unifi-squashfs-factory.bin -d
Found mtd block: /dev/mtd0(u-boot)
Found mtd block: /dev/mtd1(u-boot-env)
Found mtd block: /dev/mtd2(kernel)
Found mtd block: /dev/mtd3(cfg)
Found mtd block: /dev/mtd4(EEPROM)
Got U-Boot variable: mtdparts = mtdparts=mtdparts=ath-nor0:384k(u-boot),64k(u-boot-env),7424k(kernel),256k(cfg),64k(EEPROM)
Adding U-Boot partition: u-boot 9F000000 00060000
Adding U-Boot partition: u-boot-env 9F060000 00010000
Adding U-Boot partition: kernel 9F070000 00740000
Adding U-Boot partition: cfg 9F7B0000 00040000
Adding U-Boot partition: EEPROM 9F7F0000 00010000
Calculating flash size:
Adding block: /dev/mtd0("u-boot") - size: 00060000
Adding block: /dev/mtd1("u-boot-env") - size: 00010000
Adding block: /dev/mtd2("kernel") - size: 00740000
Adding block: /dev/mtd3("cfg") - size: 00040000
Adding block: /dev/mtd4("EEPROM") - size: 00010000
Total flash size: 00800000
Flash start: 9F000000
Flash end: 9F800000
Header MAGIC 'OPEN'
Current: BZ.qca9342.v3.7.19.5372.161007.0916

New ver: BZ.qca9342.v6.0.0-OpenWrt-50104
FW Part: "kernel"(1), MAGIC: 'PART', Base: 0x9F050000, DLen: 0x00100000, PLen: 0x00100000
FW Part: "rootfs"(2), MAGIC: 'PART', Base: 0x9F150000, DLen: 0x00380004, PLen: 0x00660000
Invalid FW Part 3 MAGIC 'END.'

Help me with advice on how to add code

Re: Ubiquiti UniFi AP-LR

Any idea?

Re: Ubiquiti UniFi AP-LR

Uiquiti devices have TFTP recovery so you don't have to worry too much about bricking  Can you open the case and connect a serial console?  Some of them are glued together so that's not easy.

Re: Ubiquiti UniFi AP-LR

I can not instaling image from wiki.openwrt.org/toh/ubiquiti/unifi from ssh.

Current: BZ.qca9342.v3.7.19.5372.161007.0916

New ver: BZ.ar934x.v6.0.0-OpenWrt-50104
Invalid version 'BZ.ar934x.v6.0.0-OpenWrt-50104'

Is it possible to install this image via TFTP?