Hello,
I have used OpenWRT on devices many times before and I love it, but I have recently tried flashing it to a TP-Link TD-W9980 v1 and have come unstuck.
I have followed the OpenWRT Wiki guide for the W9980.
After transferring u-boot I get the error "SPI flash not selected" so I am unable to erase the SPI and flash the OpenWRT firmware image.
Please see below for serial capture (I didn't capture the transfer of u-boot using "cat u-boot.asc > /dev/ttyUSB0") :
ROM VER: 1.1.4
CFG 04
EEPROM Data OK
UART
********************************************************************************
U-Boot 2010.06-LANTIQ-v-2.0.40-00014-g0553908 (Oct 19 2015 - 22:30:36)
CLOCK CPU 500M RAM 250M
DRAM: 64 MiB
Using default environment
In: serial
Out: serial
Err: serial
Net: Internal phy(GE) firmware version: 0x841d
vr9 SwitchFailed to initialize SPI flash at 0:3
No SPI flash selected. Please run `sf probe'
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
VR9 # tftp $(loadaddr) openwrt-15.05.1-lantiq-xrx200-TDW8970-sysupgrade.image
Failed to initialize SPI flash at 0:3
No SPI flash selected. Please run `sf probe'
Using vr9 Switch device
TFTP from server 192.168.1.2; our IP address is 192.168.1.1
Filename 'openwrt-15.05.1-lantiq-xrx200-TDW8970-sysupgrade.image'.
Load address: 0x80800000
Loading: T #################################################################
#################################################################
#################################################################
#################################################################
##########################
done
Bytes transferred = 4194308 (400004 hex)
VR9 # sf erase 0x20000 0x7a0000
No SPI flash selected. Please run `sf probe'
And a capture from a normal boot with TP-Link firmware:
ROM VER: 1.1.4
CFG 05
DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa3ffffff
DDR check ok... start booting...
U-Boot 2010.06-svn14907-LANTIQ-v-2.3.08 (Jan 22 2016 - 10:08:47)
CLOCK CPU 500M RAM 250M
DRAM: 64 MiB
Using default environment
In: serial
Out: serial
Err: serial
Net: Internal phy(GE) firmware version: 0x8434
vr9 Switch8192 KiB GD25Q64C at 0:3 is now current device
MAC: 98-de-d0-ac-21-de
run "flash_flash" to bring up the kernel
Hit any key to stop autoboot: 0
8192 KiB GD25Q64C at 0:3 is now current device
8192 KiB GD25Q64C at 0:3 is now current device
Uncompressing ...
Starting kernel ...
Lantiq xDSL CPE VR9
mips_hpt_frequency = 250000000, counter_resolution = 2
Linux version 2.6.32.32 (swd@localhost.localdomain) (gcc version 4.3.3 (GCC) ) 6
phym = 04000000, mem = 04000000, max_pfn = 00004000
Reserving memory for CP1 @0xa4000000, size 0x00000000
CPU revision is: 00019556 (MIPS 34Kc)
Determined physical RAM map:
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: root=/dev/mtdblock2 rw rootfstype=squashfs ip=192.168.1.1:=
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 32kB, VIPT, 4-way,
linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00040280
Readback ErrCtl register=00040280
Memory: 60596k/65536k available (2881k kernel code, 4872k reserved, 826k data, )
Hierarchical RCU implementation.
NR_IRQS:185
Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH
console [ttyS0] enabled
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2011 Lantiq DeutschlH
Lantiq PCIe Root Complex driver, version 1.5.3, (c) 2001-2011 Lantiq DeutschlanH
bio: create slab <bio-0> at 0
pci 0000:00:00.0: PME# supported from D1 D2
pci 0000:00:00.0: PME# disabled
ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: PME# supported from D0 D1 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x1c000000-0x1c0fffff
pci 0000:01:00.0: PREFETCH window: disabled
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
gptu: totally 6 16-bit timers/counters
gptu: misc_register on minor 63
gptu: succeeded to request irq 118
gptu: succeeded to request irq 119
gptu: succeeded to request irq 120
gptu: succeeded to request irq 121
gptu: succeeded to request irq 122
gptu: succeeded to request irq 123
IFX DMA driver, version ifxmips_dma_core.c:v1.0.17
,(c)2009 Infineon Technologies AG
Lantiq CGU driver, version 1.1.27, (c) 2001-2011 Lantiq Deutschland GmbH
vpe1_mem = 0
Wired TLB entries for Linux read_c0_wired() = 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
fuse init (API version 7.13)
msgmni has been set to 118
Line: 127, function: deu_init
DMA Referenced PAGE_SIZE = 4096
Infineon Technologies DEU driver version 2.0.0
IFX DEU DES initialized (multiblock) (DMA).
IFX DEU AES initialized (multiblock) (DMA).
IFX DEU ARC4 initialized (multiblock) (DMA).
IFX DEU SHA1 initialized (DMA).
IFX DEU MD5 initialized (DMA).
IFX DEU SHA1_HMAC initialized (DMA).
IFX DEU MD5_HMAC initialized (DMA).
io scheduler noop registered (default)
ifx_pmu_init: Major 252
Lantiq PMU driver, version 1.2.2, (c) 2001-2011 Lantiq Deutschland GmbH
Lantiq GPIO driver, version 1.2.14, (c) 2001-2011 Lantiq Deutschland GmbH
Infineon Technologies RCU driver version 1.0.8
Lantiq LED Controller driver, version 1.0.6, (c) 2001-2011 Lantiq Deutschland GH
Lantiq (VRX) DSL CPE MEI driver, version 1.4.4, (c) 2013 Lantiq Deutschland GmbH
ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC
Register ASC (UART) to PMCU.
Lantiq ASC (UART) driver, version 1.0.9, (c) 2001-2011 Lantiq Deutschland GmbH
brd: module loaded
loop: module loaded
Lantiq SSC driver, version 2.2.6, (c) 2001-2011 Lantiq Deutschland GmbH
Register flash device:flash0
SPI Device: GD25Q64C 0xC8 (GD) 0x40 0x17
Parameters: num sectors = 128, sector size = 65536, write size = 256
7 cmdlinepart partitions found on MTD device ifx_sflash
Creating 7 MTD partitions on "ifx_sflash":
0x000000000000-0x000000020000 : "boot"
0x000000020000-0x000000160000 : "kernel"
0x000000160000-0x0000007c0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
0x0000007c0000-0x0000007d0000 : "config"
0x0000007d0000-0x0000007e0000 : "romfile"
0x0000007e0000-0x0000007f0000 : "rom"
0x0000007f0000-0x000000800000 : "radio"
Lantiq SPI flash driver, version 1.1.9, (c) 2001-2011 Lantiq Deutschland GmbH
ifxmips_gpio: Pin ID 10 (port 0, pin 10) has been reserved by module SFLASH fro!
ifx_dataflash_init status error 255
PPP generic driver version 2.4.2
NET: Registered protocol family 24
IFX SWITCH API, Version 1.1.7.2
SWAPI: Registered character device [switch_api] with major no [81]
Switch API: PCE MicroCode loaded !!
Init IFX_ETHSW_Switch_API_procModule successfully.
Switch Auto Polling value = 0
GPHY FW load for A2x !!
GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR : 410000
IFX GPHY driver GE Mode, version ifxmips_vr9_gphy: V0.9 - Firmware: 8434
Registered led device: broadband_led
Registered led device: internet_led
Registered led device: usb1_link_led
Registered led device: usb2_link_led
Lantiq LED driver, version 1.0.17, (c) 2001-2011 Lantiq Deutschland GmbH
Mirror/redirect action on
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (947 buckets, 5120 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Ebtables v2.0 registered
NET: Registered protocol family 8
atmpvc_init() failed with -17
KOAM is loaded successfully.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 184k freed
starting pid 190, tty '': '/etc/init.d/rcS'
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
IFXUSB: ifxusb_hcd: version 3.2 B120208
Chip Version :0002 BurstSize=4
IFXUSB: USB core #0 soft-reset
IFXUSB: USB core #0 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1
ifxusb_hcd ifxusb_hcd: irq 54, io mem 0xbe101000
IFXUSB: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
IFXUSB: USB core #1 soft-reset
IFXUSB: USB core #1 soft-reset
ifxusb_hcd ifxusb_hcd: IFX USB Controller
ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2
ifxusb_hcd ifxusb_hcd: irq 83, io mem 0xbe106000
IFXUSB: Init: Power Port (0)
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
dns_init
domain_name:tplinkmodem.net
Please press Enter to activate this console. [ dm_readFile ] 2042: can not opel
[ dm_loadCfg ] 2254: software version is not match, in config, version = 0
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/default_config.xml!, al
[ parseConfigNode ] 522: Meet unrecognized object node "PhDDNSCfg", skip the ne
[ parseConfigNode ] 527: Meet unrecognized parameter node "PhDDNSCfg", skip the
[ parseConfigNode ] 522: Meet unrecognized object node "X_TPLINK_WANUSB3gLinkCe
[ parseConfigNode ] 522: Meet unrecognized object node "QueueManagement", skipe
[ parseConfigNode ] 522: Meet unrecognized object node "X_TPLINK_IPTVCfg", skie
[ parseConfigNode ] 522: Meet unrecognized object node "VoiceService", skip the
[ parseConfigNode ] 527: Meet unrecognized parameter node "VoiceService", skipe
[ parseConfigNode ] 522: Meet unrecognized object node "X_TPLINK_SpeedDialCfg"e
[ parseConfigNode ] 522: Meet unrecognized object node "X_TPLINK_MultiIspDialPe
[ parseConfigNode ] 522: Meet unrecognized object node "X_TPLINK_CallLogCfg", e
[ freshLineState ] 606: Can not open /dev/dsl_cpe_api for reading!
[ freshLineState ] 606: Can not open /dev/dsl_cpe_api for reading!
Loading E5 (MII0/1) driver ...... MAC-0: 98-de-d0-ac-21-de
MAC-1: 98-de-d0-ac-21-df
Succeeded!
PPE datapath driver info:
Version ID: 64.3.3.1.0.1.1
Family : VR9
DR Type : Normal Data Path | Indirect-Fast Path
Interface : MII0 | MII1
Mode : Routing
Release : 0.1.1
PPE 0 firmware info:
Version ID: 7.1.5.1.0.33
Family : VR9
FW Type : Standard
Interface : MII0/1 + PTM
Mode : reserved - 1
Release : 0.33
PPE 1 firmware info:
Version ID: 7.2.1.6.2.0
Family : VR9
FW Type : Acceleration
Interface : MII0 + MII1
Mode : Bridging + IPv4 Routing
Release : 2.0
IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
Lantiq CPE API Driver version: DSL CPE API V4.16.6-pd1
Predefined debug level: 3
ifx_ppa_api: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
PPA API --- init successfully
ifx_ppa_init - init succeeded
wlan0 no private ioctls.
wlan0.0 no private ioctls.
wlan0.0 no private ioctls.
ath0 no private ioctls.
ath2 no private ioctls.
ath2 no private ioctls.
sendto: No such file or directory
send 2001 error 251, -1
[ oal_sys_getOldTZInfo ] 330: Open TZ file error!
ioctl: No such device
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
[ rsl_initLanIgmpSnoopObj ] 181: We need vlan if we want igmp snooping
ath0 no private ioctls.
ath1 no private ioctls.
wlan0 no private ioctls.
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device eth0.2 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(eth0.2) entering forwarding state
device eth0.3 entered promiscuous mode
br0: port 2(eth0.3) entering forwarding state
device
eth0.4 entered promiscuous mode
br0: port 3(eth0.4) entering forwarding state
device eth0.5 entered promiscuous mode
br0: port 4(eth0.5) entering forwarding state
*********cal_data*******
a55a00000000000000000000*********end*******
ath_hal: 0.9.17.1 (AR5212, AR5416, AR9380, RF5111, RF5112, RF2413, RF5413, RF23)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Righd
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reservd
ath_pci: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
@@@@@@@@@@@@@devid = ff1c@@@@@@@@
@@@@@@@@@@@@@devid = 2e@@@@@@@@
CalData[0] = 0xa5
CalData[1] = 0x5a
CalData[2] = 0x0
CalData[3] = 0x0
CalData[4] = 0x0
CalData[5] = 0x3
CalData[6] = 0x60
CalData[7] = 0x0
CalData[8] = 0x16
CalData[9] = 0x8c
CalData[10] = 0x0
CalData[11] = 0x2d
CalData[12] = 0x60
CalData[13] = 0x8
CalData[14] = 0x0
CalData[15] = 0x1
CalData[16] = 0x2
CalData[17] = 0x80
CalData[18] = 0x60
CalData[19] = 0x2c
CalData[20] = 0x16
CalData[21] = 0x8c
CalData[22] = 0xa1
CalData[23] = 0x99
CalData[24] = 0x50
CalData[25] = 0x0
CalData[26] = 0x16
CalData[27] = 0x8c
CalData[28] = 0x0
CalData[29] = 0x2e
CalData[30] = 0x50
CalData[31] = 0x8
CalData[32] = 0x0
CalData[33] = 0x1
CalData[34] = 0x2
CalData[35] = 0x80
CalData[36] = 0x50
CalData[37] = 0x2c
CalData[38] = 0x16
CalData[39] = 0x8c
CalData[40] = 0xa1
CalData[41] = 0x99
CalData[42] = 0x50
CalData[43] = 0x64
CalData[44] = 0x8c
CalData[45] = 0xc0
CalData[46] = 0x5
CalData[47] = 0x4
CalData[48] = 0x57
CalData[49] = 0xc
CalData[50] = 0x3f
CalData[51] = 0x1
CalData[52] = 0x22
CalData[53] = 0x0
CalData[54] = 0x50
CalData[55] = 0x6c
CalData[56] = 0x3c
CalData[57] = 0x11
CalData[58] = 0x0
CalData[59] = 0x3
CalData[60] = 0x40
CalData[61] = 0x4
CalData[62] = 0x5
CalData[63] = 0xb
CalData[64] = 0x0
CalData[65] = 0x4a
CalData[66] = 0x40
CalData[67] = 0x74
CalData[68] = 0x0
CalData[69] = 0x3
CalData[70] = 0x0
CalData[71] = 0x0
CalData[72] = 0x40
CalData[73] = 0x0
CalData[74] = 0x50
CalData[75] = 0x1
CalData[76] = 0x1
CalData[77] = 0xc2
CalData[78] = 0x60
CalData[79] = 0x34
CalData[80] = 0x0
CalData[81] = 0x44
CalData[82] = 0x0
CalData[83] = 0x0
CalData[84] = 0x51
CalData[85] = 0xc
CalData[86] = 0x20
CalData[87] = 0x10
CalData[88] = 0x0
CalData[89] = 0x6
CalData[90] = 0x51
CalData[91] = 0x64
CalData[92] = 0x14
CalData[93] = 0x12
CalData[94] = 0xff
CalData[95] = 0x24
CalData[96] = 0x51
CalData[97] = 0x68
CalData[98] = 0x17
CalData[99] = 0xff
CalData[100] = 0x0
CalData[101] = 0x15
CalData[102] = 0x50
CalData[103] = 0x68
CalData[104] = 0x20
CalData[105] = 0x10
CalData[106] = 0x0
CalData[107] = 0x19
CalData[108] = 0xff
CalData[109] = 0xff
CalData[110] = 0xff
CalData[111] = 0xff
CalData[112] = 0xff
CalData[113] = 0xff
CalData[114] = 0xff
CalData[115] = 0xff
CalData[116] = 0xff
CalData[117] = 0xff
CalData[118] = 0xff
CalData[119] = 0xff
CalData[120] = 0xff
CalData[121] = 0xff
CalData[122] = 0xff
CalData[123] = 0xff
CalData[124] = 0xff
CalData[125] = 0xff
CalData[126] = 0xff
CalData[127] = 0xff
CalData[128] = 0xff
CalData[129] = 0xff
CalData[130] = 0xff
CalData[131] = 0xff
CalData[132] = 0xff
CalData[133] = 0xff
CalData[134] = 0xff
CalData[135] = 0xff
CalData[136] = 0xff
CalData[137] = 0xff
CalData[138] = 0xff
CalData[139] = 0xff
CalData[140] = 0xff
CalData[141] = 0xff
CalData[142] = 0xff
CalData[143] = 0xff
CalData[144] = 0xff
CalData[145] = 0xff
CalData[146] = 0xff
CalData[147] = 0xff
CalData[148] = 0xff
CalData[149] = 0xff
CalData[150] = 0xff
CalData[151] = 0xff
CalData[152] = 0xff
CalData[153] = 0xff
CalData[154] = 0xff
CalData[155] = 0xff
CalData[156] = 0xff
CalData[157] = 0xff
CalData[158] = 0xff
CalData[159] = 0xff
CalData[160] = 0xff
CalData[161] = 0xff
CalData[162] = 0xff
CalData[163] = 0xff
CalData[164] = 0xff
CalData[165] = 0xff
CalData[166] = 0xff
CalData[167] = 0xff
CalData[168] = 0xff
CalData[169] = 0xff
CalData[170] = 0xff
CalData[171] = 0xff
CalData[172] = 0xff
CalData[173] = 0xff
CalData[174] = 0xff
CalData[175] = 0xff
CalData[176] = 0xff
CalData[177] = 0xff
CalData[178] = 0xff
CalData[179] = 0xff
CalData[180] = 0xff
CalData[181] = 0xff
CalData[182] = 0xff
CalData[183] = 0xff
CalData[184] = 0xff
CalData[185] = 0xff
CalData[186] = 0xff
CalData[187] = 0xff
CalData[188] = 0xff
CalData[189] = 0xff
CalData[190] = 0xff
CalData[191] = 0xff
CalData[192] = 0xff
CalData[193] = 0xff
CalData[194] = 0xff
CalData[195] = 0xff
CalData[196] = 0xff
CalData[197] = 0xff
CalData[198] = 0xff
CalData[199] = 0xffdfs_attach: use DFS enhancements
DFS min filter rssiThresh = 18
DFS max pulse dur = 151 ticks
ath_get_caps[5105] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5080] tx chainmask mismatch actual 3 sc_chainmak 0
Register wlan WPS function, dev=0x82e8c000
Register wlan button on function
Register wlan button off function
wifi0: Atheros ???: mem=0x1c000000, irq=136 hw_base=0xbc000000
ath_netdev_set_macaddr: ffffff98:ffffffde:ffffffd0:ffffffac:21:ffffffde
ni aponly is null!
wlan_vap_create : enter. devhandle=0x82e8c2c0, opmode=IEEE80211_M_HOSTAP, flags1
wlan_vap_create : exit. devhandle=0x82e8c2c0, opmode=IEEE80211_M_HOSTAP, flags=.
VAP device ath0 created
ath0
wlan_vap_create : enter. devhandle=0x82e8c2c0, opmode=IEEE80211_M_STA, flags=0x3
wlan_vap_create : exit. devhandle=0x82e8c2c0, opmode=IEEE80211_M_STA, flags=0x3.
VAP device ath1 created
ath1
wlan_vap_create : enter. devhandle=0x82e8c2c0, opmode=IEEE80211_M_HOSTAP, flags1
wlan_vap_create : exit. devhandle=0x82e8c2c0, opmode=IEEE80211_M_HOSTAP, flags=.
VAP device ath2 created
ath2
DES SSID SET=TP-LINK_2.4GHz_AC21DE
DFS min filter rssiThresh = 15
DFS max pulse dur = 151 ticks
ni aponly is null!
WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
SET failed on device ath0 ; Invalid argument.
DES SSID SET=TP-LINK_Guest_2.4GHz
Reading topology file /var/Wireless/2_4G_topology.conf ...
015.570: Reading radio configuration file /var/Wireless/2_4G_80211g.ap_radio ...
015.571: Reading bss configuration file /var/Wireless/ath0.ap_bss ...
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
Using interface ath0 with hwaddr 98:de:d0:ac:21:de and ssid 'TP-LINK_2.4GHz_AC2'
DES SSID SET=TP-LINK_2.4GHz_AC21DE
015.887: upnp_wps_device_init called
l2_packet_receive - recvfrom: Network is down
ni aponly is null!
Scan in progress.. Cancelling it
l2_packet_receive - recvfrom: Network is down
device ath0 entered promiscuous mode
device ath1 entered promiscuous mode
brctl: bridge br0: Device or resource busy
device ath2 entered promiscuous mode
[4294684846] mtlk0(mtlk_cdev_init:355): Max nodex set to 1048575
[4294686546] mtlk0(__mtlk_print_endianess:4724): The system is Big endian (0xbe)
[4294686546] mtlk0(mtlk_fast_mem_print_info:114): Using normal memory for hot ct
[4294686556] mtlk0(_mtlk_df_user_alloc_devname:8341): NDEV Name pattern: wlan%d
[4294686566] mtlk0(mtlk_core_pdb_fast_handles_open:42): Open Hot-path parameters
mtlk 0000:00:0e.0: firmware: requesting cal_wlan0.bin
[4294686846] mtlk<3>(_mtlk_df_fw_request_firmware:63): Firmware (cal_wlan0.bin)g
mtlk 0000:00:0e.0: firmware: requesting ap_upper_wave300.bin
mtlk 0000:00:0e.0: firmware: requesting contr_lm.bin
ni aponly is null!
[4294687806] mtlk0(_mtlk_core_start:3451): CID-0000: ap_upper_wave300.bin: @@@ @
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.4.2_r3444 MIPS: Lower @
[4294687866] mtlk0(mtlk_eeprom_check_ee_data:1353): Options mask is 0x00
[4294687876] mtlk0(load_default_hw_table:2119): HW configuration is 3X3
[4294687896] mtlk0(_mtlk_df_user_ppa_register:541): PPA device function is regi)
[4294687916] mtlk0(_mtlk_core_mbss_add_vap:7425): CID-0000: Got PRM_ID_VAP_ADD
[4294687926] mtlk0(_mtlk_df_user_alloc_devname:8341): NDEV Name pattern: wlan0.0
[4294687936] mtlk0(mtlk_core_pdb_fast_handles_open:42): Open Hot-path parameters
[4294687936] mtlk0(_mtlk_core_start:3451): CID-0001: ap_upper_wave300.bin: @@@ @
contr_lm.bin: @@@ VERSION INFO @@@ version number: FW_3.4.2_r3444 MIPS: Lower @
[4294687986] mtlk0(_mtlk_core_mbss_add_vap:7443): CID-0000: VAP#1 added
device wlan0 entered promiscuous mode
brctl: iface lq1: No such device
device wlan0.0 entered promiscuous mode
sendto: No such file or directory
send 2030 error 251, -1
[ oal_startUPnP ] 352: TD-W9980, TD-W9980
sendto: No such file or directory
send 2004 error 251, -1
sendto: No such file or directory
send 2004 error 251, -1
sendto: No such file or directory
send 2004 error 251, -1
Many Thanks,
Paul
(Last edited by nobodydoesITbetter on 13 Oct 2016, 10:17)