OpenWrt Forum Archive

Topic: Xclaim Xi-1 board

The content of this topic has been archived on 8 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Here we go.

CPU : AR9342-bl1a
32 ROM - Spansion FL256SA FRO
64 RAM  - NT5TU32M16DG–AC
Gigabit Switch - AR8035-A

Board :

http://imgur.com/a/Oh8jy

Boot log :

chip id(1122) bootstrap(ae0736)
U-Boot 1.1.4.54 (Sep 17 2014 - 15:03:30)
Spaniel 1.0.1.36 - built 15:03:30, Sep 17 2014
DRAM:  
sri
Wasp 1.2
wasp_ddr_initial_config(252): (16bit) ddr2 init
wasp_ddr_initial_config(433): Wasp ddr init done
Tap value selected = 0xe [0x0 - 0x1d]
Setting 0xb8116290 to 0x20402d0f
16
64 MB
Top of RAM usable for U-Boot at: 83ff0000
Reserving 346k for U-Boot at: 83f98000
Reserving 768k for malloc() at: 83ed8000
Reserving 44 Bytes for Board Info at: 83ed7fd4
Reserving 36 Bytes for Global Data at: 83ed7fb0
Reserving 128k for boot params() at: 83eb7fb0
Stack Pointer at: 83eb7f98
Now running in RAM - U-Boot at: 83f98000
u-boot-env crc:  ok
spi: 0x244
id read 0x10219
sector count = 512
Flash: 32 MB
flash_reserved_offset=0xbff80000 flash_end_reserved_bytes=0x1080000
board_configuration(0x83f180e8) @ 0xbff80000
v54 mac addr:  f0 b0 52 22 82 03
pci_init_board: PCIe PLL not set for 40MHz refclk
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
 wasp  reset mask:c03300 
WASP  ----> F1 PHY *
: cfg1 0xf cfg2 0x7114
eth0: f0:b0:52:22:82:03
F1Phy reg init 
ATHR_AUTONEG_ADVERT:1DE1
ATHR_1000BASET_CONTROL:200
ATHR_PHY_CONTROL:3100
ATHRSF1_PHY: Port 6, Neg Success
ATHRSF1_PHY: unit 0 phy addr 6 eth0 up
eth0
No Himem Boot Script !!!
Checking auto/recovery boot
Main image_id = 2
 Booting image rcks_wlan.bkup (5) type:2/2 ...
Hit Ctrl-c to stop autoboot:  2  1  0 
RKS Header: load_address=0x80080000
RKS Header: offset=0xa0, entry=0x80084230, len=8806240
Image loaded from 80080000-803ce6ac
cmdline: console=ttyS0,115200r mem=0x03ff0000 flash=0x02000000 uboot=1 usb 
Linux version 2.6.32.24 (jenkins@hq-ubuntu-build04) (gcc version 4.3.5 (Buildroot ) ) #1 Thu Oct 9 04:25:31 PDT 2014
arg 1: console=ttyS0,115200r mem=0x03ff0000 flash=0x02000000 uboot=1 usb 
bootconsole [early0] enabled
CPU revision is: 0001974c (MIPS 74Kc)
cpu(560000000) ahb(224999936) ddr(449999872)
config(0x80208483)
Determined physical RAM map:
 memory: 03ff0000 @ 00000000 (usable)
---> v54_fix_mem_size: mem_size: 3ff0000 @ [a0000000,a4000000] reserved=10000
User-defined physical RAM map:
 memory: 03ff0000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00003ff0
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003ff0
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16240
Kernel command line: console=ttyS0,115200r mem=0x03ff0000 flash=0x02000000 uboot=1 usb  
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
get_c0_compare_irq.
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 60816k/65472k available (2513k kernel code, 4580k reserved, 706k data, 164k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
plat_time_init.
ar7100_timer_init.
get_c0_compare_int.
Console: colour dummy device 80x25
Calibrating delay loop... 278.52 BogoMIPS (lpj=139264)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
***** Warning *****: PCIe WLAN H/W not found !!!
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
AR7100 GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.
msgmni has been set to 118
cryptomgr_test used greatest stack depth: 15184 bytes left
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
kstat_init_tasklets: hash=0x46, func=0x801b6fb0 uart_tasklet_action
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Serial Hornet: 8250/16550 driver $Revision: #1 $ 1 ports, IRQ sharing disabled
ttyHS0: detected caps 00000000 should be 00000100
ar934x_uart.0: ttyHS0 at MMIO 0xb8500000 (irq = 22) is a 16550A
---> [803eb000, 803eb000] size=0
---> rd_size = 0x2000 __rd_size = 0x4 ... no change
rd_size=8192 BLK_DEV_RAM_SIZE=8192
brd: module loaded
QLogic Fibre Channel HBA Driver: 8.03.01-k6
spi(0x245)
uboot_parts(1)
khelper used greatest stack depth: 15120 bytes left
cmdlinepart partition parsing not available
parse_redboot_partitions: Load Type = 2
master:{size=2000000 erasesize=10000}, directory=-4 offset=f40000
offset=f40000 flash_reserved_offset=f80000
Searching for RedBoot partition table in ar7100-nor0 at offset 0xf40000
No RedBoot partition table detected in ar7100-nor0
parse_redboot_partitions: main image: address = 00040000, size = 00d00000.
parse_redboot_partitions: bkup image: address = 01000000, size = 00d00000.
parse_redboot_partitions: rootfs partition, name=v54_$rootfs$_2, type=2, block=7
parse_redboot_partitions: flash root fs block = 7
8 RedBoot partitions found on MTD device ar7100-nor0
Creating 8 MTD partitions on "ar7100-nor0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000d40000 : "rcks_wlan.main"
0x000000d40000-0x000000f40000 : "datafs"
0x000000f40000-0x000000f80000 : "u-boot-env"
0x000000f80000-0x000001000000 : "Board Data"
0x000001000000-0x000001130000 : "rcks_wlan.bkup"
0x000001130000-0x000001d00000 : "v54_$rootfs$_2"
0x000001d00000-0x000002000000 : "datafs2"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

In ar7100_ehci_drv_probe
probing ehci...
hcd->regs is bb000000
ehci->caps is bb000100
ehci->regs is bb000140
ar7100-ehci ar7100-ehci.0: AR7100 EHCI
ar7100-ehci ar7100-ehci.0: new USB bus registered, assigned bus number 1
ath_usb_ehci_init
ehci_reset: Initialize USB CONTROLLER in host mode: 13
ehci_reset: Port Status 1c000000
ar7100-ehci ar7100-ehci.0: irq 3, io mem 0x1b000000
ehci_reset: Initialize USB CONTROLLER in host mode: 13
ehci_reset: Port Status 1c000000
ar7100-ehci ar7100-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
...probing done
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver libusual
v54_bsp: Version 1.1
Copyright (c) 2004-2007 Ruckus Wireless, Inc.All Rights Reserved
board_configuration(0x803e546c) @ 0xf80000
v54rb: creating proc file himem_v54rb
v54cf: create proc file himem_v54cf
rb_init_module: device=v54rb, major=55, count=2 ... 
rb_init_module: v54rb's major dev number=55 
rb_init_module: setup dev v54rb major=55, minor=0, mem_start=a3ff5400, sizeof(ring_buffer)=16 
rb_init_module: setup dev v54rb major=55, minor=1, mem_start=a3ffa800, sizeof(ring_buffer)=16 
cf_init_module: device=v54cf, major=56, count=0 ... 
cf_init_module: No high memory available for v54cf, ignore init ... 
pktgen 2.72: Packet Generator for packet performance testing.
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Hello world, ruckus generic netlink!
register rks_genl_family succeeded
prepare_namespace: mount from flash
VFS: Mounted root (squashfs filesystem) readonly on device 31:7.
Freeing unused kernel memory: 164k freed
Algorithmics/MIPS FPU Emulator v1.5
watchdog_task: priority -15

Starting watchdog ... 

mount used greatest stack depth: 14936 bytes left
mount used greatest stack depth: 14744 bytes left
net.ipv4.ip_local_port_range = 32768 61000
mount used greatest stack depth: 14224 bytes left
Initializing random number generator... done.
rm: cannot remove '*': No such file or directory
/etc/init.d/sys_init: cd: line 217: can't cd to /ca-certs
cp: cannot stat '*.': No such file or directory
- rpm version(4), older version(0) -
Jan  1 00:00:04 Custom_Migrate[76]: No custom v1 file, nothing to do...

fix_defaults used greatest stack depth: 14008 bytes left
/dev/mtdblock7 oprocfs_write: buf=enable 1 1
, len=11 
n / type squashfprocfs_write: cmd=enable, dev minor=1, val=1, buf=<NULL> 
s (ro,relatime)
/proc on /proc type proc (rw,relatime)
sys on /sys type sysfs (rw,relatime)
tmpfs on /tmp type tmpfs (rw,relatime,size=4M)
/dev/mtdblock3 on /writable type jffs2 (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
sys_init ........ [started] (1.501)
rsm_oem_legacy: get null oem company name
dropbearkey used greatest stack depth: 13848 bytes left
rsm_init ........ [started] (0.855)
rudb: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
hello rflow
kernel_resource . [started] (0.243)
timer ........... [started] (0.000)
Starting network...
+ insmod /lib/modules/2.6.32.24/kernel/drivers/net/atheros/athrs_gmac.ko ethnames=eth0
Thu Oct  9 10:57:00 UTC 2014
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
eth0
kstat_init_tasklets: hash=0x17, func=0x83bb3518 athr_gmac_txreap_task
dev0 = 0x83b25c00 macaddr = f0 b0 52 22 82 03 
ATHR_GMAC: Max segments per packet :   1
ATHR_GMAC: Max tx descriptor count :   128
ATHR_GMAC: Max rx descriptor count :   192
ATHR_GMAC: Mac capability flags    :   44380
+ rc=0
+ set +x
network ......... [started] (1412852214.753)
wlan: 0.8.4.2 (Atheros/multi-bss)
register rks_aerosct_genl_family succeeded
register rks_aerosct_genl_ops succeeded
register rks_ekahau_genl_family succeeded
register rks_ekahau_genl_ops succeeded
kstat_init_tasklets: hash=0xdb, func=0xc04e2a7c rks_sw2_tasklet
register rks_sw2_genl_family succeeded
register rks_sw2_genl_ops succeeded
ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, PRIVATE_DIAG, 11D)
ath_rate_rks_bflex_bcs
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_spectral: Version 2.0.0.Ruckus
Copyright (c) 2005-2009 Atheros Communications, Inc.
Copyright (c) 2011 Ruckus Wireless, Inc.
All Rights Reserved
SPECTRAL module built on Oct  9 2014 04:33:37
wlan: mac acl policy registered
ath_ahb: 0.9.4.5 (Atheros/multi-bss)
kstat_init_tasklets: hash=0xb4, func=0x82dc4ca4 ath_rx_tasklet
kstat_init_tasklets: hash=0xb0, func=0x82ddd13c owl_tx_tasklet
kstat_init_tasklets: hash=0x8f, func=0x82dd3ae8 ath_bmiss_tasklet
kstat_init_tasklets: hash=0x06, func=0x82dcb6ec ath_bstuck_tasklet
kstat_init_tasklets: hash=0x8e, func=0x82dc8e5c ath_beacon_channel_change_tasklet
kstat_init_tasklets: hash=0xaa, func=0x82dcb640 ath_fatal_tasklet
------- DEV ID = 0x31 --------- 
Boostrap clock 40MHz
ar9300Attach: This Mac Chip Rev 0x300.0 is 
ar9300Attach: Using WASP Chip
Enterprise mode: 0x03fc0004
ar9300RadioAttach: Need analog access recipe!!
ar9300EepromRestoreFromFlash: calmem=a0fc0000 mdataSize=1088 start=0xfc0000 cal offset=4096
               ath_attach: radio 0, mac f0:b0:52:22:82:08
ath_hal_init_channels: regdmn 0x3a, country 840, dfsDomain 1, modesAvail 0x1f80d, rd5GHz
ieee80211_announce_channels:  ic->ic_nchans 107
Chan  Freq  RegPwr  HT   CTL CTL_U CTL_L DFS Flags
   1  2412n      36  HT40   0    1    0     N   0xa0080
   1  2412b      36         0    0    0     N   0xa0
   1  2412n      36  HT20   1    0    0     N   0x10080
   1  2412g      36         0    0    0     N   0xc0
   2  2417g      36         0    0    0     N   0xc0
   2  2417n      36  HT40   0    1    0     N   0xa0080
   2  2417n      36  HT20   1    0    0     N   0x10080
   2  2417b      36         0    0    0     N   0xa0
   3  2422n      36  HT40   0    1    0     N   0xa0080
   3  2422b      36         0    0    0     N   0xa0
   3  2422g      36         0    0    0     N   0xc0
   3  2422n      36  HT20   1    0    0     N   0x10080
   4  2427g      36         0    0    0     N   0xc0
   4  2427n      36  HT20   1    0    0     N   0x10080
   4  2427b      36         0    0    0     N   0xa0
   4  2427n      36  HT40   0    1    0     N   0xa0080
   5  2432n      36  HT40   0    0    1     N   0xc0080
   5  2432n      36  HT40   0    1    0     N   0xa0080
   5  2432n      36  HT20   1    0    0     N   0x10080
   5  2432g      36         0    0    0     N   0xc0
   5  2432b      36         0    0    0     N   0xa0
   6  2437g      36         0    0    0     N   0xc0
   6  2437n      36  HT40   0    0    1     N   0xc0080
   6  2437n      36  HT40   0    1    0     N   0xa0080
   6  2437n      36  HT20   1    0    0     N   0x10080
   6  2437b      36         0    0    0     N   0xa0
   7  2442n      36  HT40   0    1    0     N   0xa0080
   7  2442n      36  HT20   1    0    0     N   0x10080
   7  2442g      36         0    0    0     N   0xc0
   7  2442n      36  HT40   0    0    1     N   0xc0080
   7  2442b      36         0    0    0     N   0xa0
   8  2447n      36  HT40   0    0    1     N   0xc0080
   8  2447n      36  HT20   1    0    0     N   0x10080
   8  2447g      36         0    0    0     N   0xc0
   8  2447b      36         0    0    0     N   0xa0
   9  2452n      36  HT40   0    0    1     N   0xc0080
   9  2452n      36  HT20   1    0    0     N   0x10080
   9  2452g      36         0    0    0     N   0xc0
   9  2452b      36         0    0    0     N   0xa0
  10  2457n      36  HT40   0    0    1     N   0xc0080
  10  2457n      36  HT20   1    0    0     N   0x10080
  10  2457g      36         0    0    0     N   0xc0
  10  2457b      36         0    0    0     N   0xa0
  11  2462n      36  HT40   0    0    1     N   0xc0080
  11  2462n      36  HT20   1    0    0     N   0x10080
  11  2462g      36         0    0    0     N   0xc0
  11  2462b      36         0    0    0     N   0xa0
  36  5180n      23  HT40   0    1    0     N   0xa0100
  36  5180n      23  HT20   1    0    0     N   0x10100
  36  5180a      23         0    0    0     N   0x140
  40  5200n      23  HT40   0    0    1     N   0xc0100
  40  5200n      23  HT20   1    0    0     N   0x10100
  40  5200a      23         0    0    0     N   0x140
  44  5220n      23  HT40   0    1    0     N   0xa0100
  44  5220n      23  HT20   1    0    0     N   0x10100
  44  5220a      23         0    0    0     N   0x140
  48  5240n      23  HT40   0    0    1     N   0xc0100
  48  5240n      23  HT20   1    0    0     N   0x10100
  48  5240a      23         0    0    0     N   0x140
  52  5260n      30  HT40   0    1    0     Y   0xa1300
  52  5260n      30  HT20   1    0    0     Y   0x11300
  52  5260a      30         0    0    0     Y   0x1340
  56  5280a      30         0    0    0     Y   0x1340
  56  5280n      30  HT40   0    0    1     Y   0xc1300
  56  5280n      30  HT20   1    0    0     Y   0x11300
  60  5300n      30  HT40   0    1    0     Y   0xa1300
  60  5300n      30  HT20   1    0    0     Y   0x11300
  60  5300a      30         0    0    0     Y   0x1340
  64  5320n      30  HT40   0    0    1     Y   0xc1300
  64  5320n      30  HT20   1    0    0     Y   0x11300
  64  5320a      30         0    0    0     Y   0x1340
 100  5500n      30  HT40   0    1    0     Y   0xa1300
 100  5500n      30  HT20   1    0    0     Y   0x11300
 100  5500a      30         0    0    0     Y   0x1340
 104  5520n      30  HT40   0    0    1     Y   0xc1300
 104  5520n      30  HT20   1    0    0     Y   0x11300
 104  5520a      30         0    0    0     Y   0x1340
 108  5540n      30  HT40   0    1    0     Y   0xa1300
 108  5540n      30  HT20   1    0    0     Y   0x11300
 108  5540a      30         0    0    0     Y   0x1340
 112  5560n      30  HT40   0    0    1     Y   0xc1300
 112  5560n      30  HT20   1    0    0     Y   0x11300
 112  5560a      30         0    0    0     Y   0x1340
 116  5580n      30  HT20   1    0    0     Y   0x11300
 116  5580a      30         0    0    0     Y   0x1340
 132  5660n      30  HT40   0    1    0     Y   0xa1300
 132  5660n      30  HT20   1    0    0     Y   0x11300
 132  5660a      30         0    0    0     Y   0x1340
 136  5680n      30  HT40   0    0    1     Y   0xc1300
 136  5680n      30  HT20   1    0    0     Y   0x11300
 136  5680a      30         0    0    0     Y   0x1340
 140  5700n      30  HT20   1    0    0     Y   0x11300
 140  5700a      30         0    0    0     Y   0x1340
 149  5745n      36  HT40   0    1    0     N   0xa0100
 149  5745n      36  HT20   1    0    0     N   0x10100
 149  5745a      36         0    0    0     N   0x140
 153  5765n      36  HT40   0    0    1     N   0xc0100
 153  5765n      36  HT20   1    0    0     N   0x10100
 153  5765a      36         0    0    0     N   0x140
 157  5785n      36  HT40   0    1    0     N   0xa0100
 157  5785n      36  HT20   1    0    0     N   0x10100
 157  5785a      36         0    0    0     N   0x140
 161  5805n      36  HT40   0    0    1     N   0xc0100
 161  5805n      36  HT20   1    0    0     N   0x10100
 161  5805a      36         0    0    0     N   0x140
 165  5825n      36  HT20   1    0    0     N   0x10100
 165  5825a      36         0    0    0     N   0x140
ath_desc_alloc:6631 Enhanced DMA Support Rx Buf configured = 575 
ath_dfs_allowed: do dfs 1, enable_dfs 1
ath_attach SPECTRAL attach successful
ath_rate_attach: memory: size 66760, mqsize 291740 ruckus_softc 49332 antinfo 49252 txctl size 17428
rks_init_ant_hw_sw: anttype=0x65 antctrl=0x5
v54_antinfo: ANTMODEL_WALL-E (65): 0 bits, 1 states, 1 omni, 1 prober, 2 gain
txctrl_init ANTMODEL_WALL-E 82a2c0b8 82a2c0c0
ath_rate_attach: wifi0 Tx 1024, Rx 575, Order 7, Max STA 384, Per STA(voice 64, video 256, data 128, bkgnd 64)
ath_attach:TxBF cap, ie=de74606 
kstat_init_tasklets: hash=0xd5, func=0xc04c2278 ieee80211_node_aging_tasklet
kstat_init_tasklets: hash=0x19, func=0xc04cfa6c scan_restart_pwrsav
ieee80211_wifipos_attach:510 lbs:[83a09380] Netlink socket created for Radio 0:83b93600

wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11na rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11na MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: 11ng rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11ng MCS:  0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: mac 768.0 phy 304.1 radio 0.0
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 9340: mem=0xb8100000, irq=2
ath_pci: 0.9.4.5 (Atheros/multi-bss)
insmod used greatest stack depth: 13176 bytes left
kstat_init_tasklets: hash=0xa6, func=0xc04bfad4 ieee80211_sta_join1_tasklet
802.11h VAP reset complete 
wlan ............ [started] (3.040)
sh used greatest stack depth: 13148 bytes left
RFW IPC 98307
local7@/dev/v54rb1
    local7  /dev/v54rb1  local7 
output_path=/dev/v54rb1, fd=-1, include facilities: 0xb8, 
Starting syslog daemon...
Device module start-up OK
WLAN module for wlan100 start-up OK
WLAN module for wlan0 start-up OK
WLAN module for wlan1 start-up OK
WLAN module for wlan2 start-up OK
WLAN module for wlan3 start-up OK
WLAN module for wlan4 start-up Failed
ATH module for wifi0 start-up OK
shaper module start-up OK
logger .......... [started] (1.234)
udhcpc (v1.15.2) started
dhcp deconfig event for interface br0 
route: SIOCADDRT: Invalid argument
Sending discover...
bridge .......... [started] (1.743)
msgd ............ [started] (0.074)
smartcast ....... [started] (0.693)
rksmcast 1.0 Copyright (C) 2007-2011 Ruckus Wireless
rksmcast currently snooping max of 6 interfaces IGMP(6) MLD(0)
gpsd ............ [started] (0.286)
IP event ........ [started] (0.137)
sshd ............ [started] (0.293)
supplicant ...... [started] (0.176)
Sending discover...
hostap .......... [started] (3.683)
eth1x ........... [started] (0.145)
auto-prov ....... [started] (0.000)
Sending discover...
webserver ....... [started] (0.196)
led ............. [started] (0.150)
rfwd ............ [started] (0.000)
Auto-Provision is not enabled/configured; exiting...
telnetd ......... [started] (0.164)
lldpd ........... [started] (0.167)
snmpd ........... [started] (0.768)
snmptrap ........ [started] (0.392)
meshd ........... [started] (0.154)
sntp ............ [started] (0.152)
hotspot ......... [started] (0.159)
hotspot-ng ...... [started] (0.099)
mdnsproxy ....... [started] (0.069)
tr069 ........... [started] (0.081)
aerosctd ........ [started] (0.212)
ekahaud ......... [started] (0.139)
Sending discover...
sysinfo-archive . [started] (0.217)
l2tp ............ [started] (0.143)
usb ............. [started] (0.263)
zapd ............ [started] (0.001)
Starting zapd...

/usr/sbin/zapd version 1.83.18, Copyright (C) 2004-2006 Ruckus Wireless, Inc. All Rights Reserved.
Built Oct  9 2014 at 04:39:08
channelfly ...... [started] (0.162)
mshngrd ......... [started] (0.153)
Channelfly (C) 2010,2011 Ruckus Wireless, Inc.
rfmd ............ [started] (0.152)
avpd ............ [started] (0.101)
statd ........... [started] (0.104)
nbp_rks ......... [started] (0.070)
rsmd: started 42/44 modules -
 (19.000)
vm.drop_caches = 3

Please login: --> wifi0: CHANNEL-CHANGE.indication: Channel (2)
Sending discover...
Sending discover...
Sending discover...
Sending discover...

Uboot env :

bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup)
mtdids=nor0=ar7100-nor0
bootdelay=2
ethact=eth0
filesize=78a000
fileaddr=81000000
ipaddr=10.0.0.1
serverip=10.0.0.5
stdin=serial
stdout=serial
stderr=serial
partition=nor0,0
mtddevnum=0
mtddevname=u-boot

Environment size: 461/262140 bytes

So far I've managed to load a uImage with no working ethernet or wifi.

I need to have a look, however, I believe eth is not detected because something related to this - https://lists.openwrt.org/pipermail/ope … 36802.html  ( not really sure if there is a placet that I can look for instructions on how to troubleshoot this )

Another issue that I've noticed is that when I use a lzma compression, the board freezes. To bypass this, I've changed it to gzip.
I'll need to see if the same issue occurs when I burn the image.

I've sent Xclaim an email to get the SDK ( or anything they have ).
Hopefully, they'll come back at one point.

(Last edited by Shogo on 22 Sep 2016, 13:48)

Hello, good to see another user here. I also have this board and was struggling to get it to load OpenWRT.

Did you make any more progress or findings ?

Did you get the SDK from Xclaim. The device is actually just rebranded Ruckus hardware.

No, I'm sort of getting ignored by them at the moment. Ruckus on twitter said that I can get in touch with the support through their portal.
However still no reply after some time.

The discussion might have continued from here.