OpenWrt Forum Archive

Topic: [Solved] U4EA Fusion 70 Managed 802.11n AP [Board: PB44]

The content of this topic has been archived on 5 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
jcook
27 Jun 2016, 12:27

Hi

I have an Fuson 70 AP but no wireless controller and I can't manually config it, from the console I have the following output

VSCXXX Found 0  unit 0:0  phy_addr: 0  id: 00070421
 PHY is Vitesse VSC8601 Rev B
VSCXXX unit 0  phy_addr 0
 mode_ctr        (00 )=1140     auto-eg
    full-duplex
    f1000
 mode_status     (01 )=7949     auto-neg-cap
    ex-cap
  rcv-error       (19 )=0000
  false-carrier   (20 )=0000
  disconnect_cnt  (21 )=0000
Ethernet eth0: MAC address 02:34:6b:83:69:93
IP: 192.168.1.2/255.255.255.0, Gateway: 192.168.1.1
Default server: 192.168.1.36

RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version R1.1 - built 07:26:31, Dec  6 2008

Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.

Board: pb44
RAM: 0x80000000-0x84000000, [0x8004a420-0x80fb1000] available
FLASH: 0xbf000000 - 0xc0000000, 64 blocks of 0x00040000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load -d KernelA
Image loaded from 0x80070000-0x80319086
RedBoot> exec -c "console=ttyS0,115200 root=31:04 rootfstype=jffs2 init=/sbin/init mem=64M@0x00000000"
Now booting linux kernel:
 Base address 0x80050000 Entry 0x80070008
 Cmdline : console=ttyS0,115200 root=31:04 rootfstype=jffs2 init=/sbin/init mem=64M@0x00000000
Linux version 2.6.15--LSDK-7.3.0.385 (jvarghese@Ban-build-server) (gcc version 3.4.4) #199 Mon Nov 2 06:17:17 IST 2009
flash_size passed from bootloader = 16
arg 1: console=ttyS0,115200 root=31:04 rootfstype=jffs2 init=/sbin/init mem=64M@0x00000000
CPU revision is: 00019374
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=31:04 rootfstype=jffs2 init=/sbin/init mem=64M@0x00000000
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 512 (order: 9, 8192 bytes)
Using 300.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61568k/65536k available (2075k kernel code, 3924k reserved, 496k data, 152k init, 0k highmem)
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
AR7100 GPIOC major 0
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Serial: 8250/16550 driver $Revision: 1.1.1.2 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x0 (irq = 19) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 8192K size 1024 blocksize
cmdlinepart partition parsing not available
Searching for RedBoot partition table in ar7100-nor0 at offset 0xf80000
11 RedBoot partitions found on MTD device ar7100-nor0
Creating 11 MTD partitions on "ar7100-nor0":
0x00000000-0x00040000 : "RedBoot"
mtd: Giving out device 0 to RedBoot
0x00040000-0x00080000 : "BootConfig"
mtd: Giving out device 1 to BootConfig
0x00080000-0x000c0000 : "BootConfigSave"
mtd: Giving out device 2 to BootConfigSave
0x000c0000-0x00240000 : "KernelA"
mtd: Giving out device 3 to KernelA
0x00240000-0x00800000 : "RootFsA"
mtd: Giving out device 4 to RootFsA
0x00800000-0x00980000 : "KernelB"
mtd: Giving out device 5 to KernelB
0x00980000-0x00f40000 : "RootFsB"
mtd: Giving out device 6 to RootFsB
0x00f40000-0x00f80000 : "Test"
mtd: Giving out device 7 to Test
0x00f80000-0x00fbf000 : "FIS directory"
mtd: partition "FIS directory" doesn't end on an erase block -- force read-only
mtd: Giving out device 8 to FIS directory
0x00fbf000-0x00fc0000 : "RedBoot config"
mtd: partition "RedBoot config" doesn't start on an erase block boundary -- force read-only
mtd: Giving out device 9 to RedBoot config
0x00fc0000-0x01000000 : "Board data"
mtd: Giving out device 10 to Board data
10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (AR7100_EHCI)
In ar7100_ehci_drv_probe<4>ar7100-ehci: probe of ar7100-ehci.0 failed with error -1
2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (ar7100_ohci)block sizes: ed 64 td 64
In ohci_hcd_ar7100_drv_probe<4>ar7100-ohci: probe of ar7100-ohci.0 failed with error -1
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (jffs2 filesystem) readonly.
Freeing unused kernel memory: 152k freed
init started:  BusyBox v1.01 (2009.02.10-02:18+0000) multi-call binary
init started:  BusyBoxAlgorithmics/MIPS FPU Emulator v1.5
 v1.01 (2009.02.10-02:18+0000) multi-call binary
Starting pid 16, console /dev/ttyS0: '/etc/rc.d/rcS'
ag7100_mod: module license 'unspecified' taints kernel.
AG7100: Length per segment 512
AG7100: Max segments per packet 4
AG7100: Max tx descriptor count    400
AG7100: Max rx descriptor count    252
AG7100: fifo cfg 3 018001ff
AG7100CHH: Mac address for unit 0
AG7100CHH: 02:34:6b:83:69:93
ag7100_ring_alloc Allocated 6400 at 0x8137e000
ag7100_ring_alloc Allocated 4032 at 0x8030e000
AG7100: cfg1 0xf cfg2 0x7014
VSC8601: Found 0  unit 0:0  phy_addr: 0  id: 00070421
VSC8601: PHY is Vitesse VSC8601 Rev B
VSC8601: unit 0  phy_addr 0
VSC8601: unit 0  phy_addr 0
AG7100: unit 0: phy not up carrier 1
Writing 4
SIOCGIFFLAGS: No such device
device eth0 entered promiscuous mode
ath_hal: 0.9.17.1 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2316, RF2317, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
**u4ea module init start
wlan: 0.8.4.2 (Atheros/multi-bss)
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
VSC8601: unit 0  phy_addr 0
AG7100: unit 0 phy is up...RGMii 100Mbps full duplex
AG7100: pll reg 0x18050010: 0x1099
AG7100: cfg_1: 0x1ff0000
AG7100: cfg_2: 0x3ff
AG7100: cfg_3: 0x18001ff
AG7100: cfg_4: 0xffff
AG7100: cfg_5: 0x3ffef
AG7100: done cfg2 0x7115 ifctl 0x10000 miictrl 0x12
DFS min filter rssiThresh = 18
DFS max pulse dur = 131 ticks
!!!!! SC Callback Registration for wifi0
wifi0: Atheros 9160: mem=0x10000000, irq=48 hw_base=0xb0000000
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
wlan: mac acl policy registered
GRE over IPv4 tunneling driver
Starting pid 310, console /dev/ttyS0: '/etc/rc.d/rc.log'
Starting pid 312, console /dev/ttyS0: '/sbin/softdog'
/sbin/softdog: software watchdog not installed in kernel
If kerneld is not running and is not properly configured, SOFTDOG
will fail. Please read the README file in the SOFTDOG distribution.

OK, kerneld loaded the module, continuing...

Starting pid 314, console /dev/ttyS0: '/u4ea/image-U4EAFUSION70.rp'
[main:598] IPADDR: 10.147.36.167
[main:603] MAC: 02:34:6b:83:69:93

AP Vendor/Model : U4EAFUSION70
Firmware Build  : 2010-07-19 11:52 +0530 /home/calwifi/sources/rubik-new-cvs/rubik/src
Firmware Version: 2574826-calwifi_ez_dev
Serial Number   : 28LC0920000454
Ethernet MACAddr: 02:34:6b:83:69:93

[00000010] INFO : Bootloader POST result code: 0x0000. {rpStartup.c:854}
[00000010] INFO : Old fatal error: Occurred 571 sec after POR. Build info: "2010-07-19 11:52 +0530 /home/calwifi/sources/rubik-new-cvs/rubik/src". {rpStartup.c:799}
[00000010] INFO : Stored error message: "Communication with all WCP(s) lost - rebooting (rpmstates.c:2513)
" {rpStartup.c:802}
[rp console] ** disabled **
rtosBootFlagsGet:2609 in wlan/wtp/rtos/linux/rtos_sys.c not implemented
rtosBootFlagsGet:2609 in wlan/wtp/rtos/linux/rtos_sys.c not implemented
[00000011] INFO : Slot 0: Radio detected AtherosLnx 802.11n 5GHz/2.4Ghz. {d11if.c:197}
[00000012] INFO : Managing controller before reboot was the primary {rpmstates.c:2148}
rtosEtherLinkStateNotify:1802 in wlan/wtp/rtos/linux/rtos_sys.c not implemented
[00000026] INFO : Sending discovery message to Primary at 10.147.36.160 {rpmstates.c:906}

If I try to load an openwrt kernel (openwrt-15.05-ar71xx-generic-pb44-kernel.bin) from tftp or [xyz]modem I have this

Board: pb44
RAM: 0x80000000-0x84000000, [0x8004a420-0x80fb1000] available
FLASH: 0xbf000000 - 0xc0000000, 64 blocks of 0x00040000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
^C
RedBoot> load -r -b %{FREEMEMLO} -m xmodem
CCCCCCRaw file loaded 0x8004a800-0x8021a7ff, assumed entry at 0x8004a800
xyzModem - CRC mode, 0(SOH)/1856(STX)/0(CAN) packets, 6 retries
RedBoot>
RedBoot> exec
Now booting linux kernel:
 Base address 0x80050000 Entry 0x8004a800
 Cmdline : console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mem=64M@0x00000000

it's a must that the kernel needs to be written to flash before executing it ?
can it be run from memory ?
I've built the latest trunk and tried the gz,lzma and uncompressed kernel, but it would not start

the flash has 16MB and has 2 images, the factory and an updated one, it can be selected via redboot,
the board is Lite-On WP741AP and is the same as the hp(3com) airconnect 9150, the hp firmware has an web based config but I don't know how to flash the img file

this is the flash layout

RedBoot> fis list
Name              FLASH addr  Mem addr    Length      Entry point
RedBoot           0xBF000000  0xBF000000  0x00040000  0x00000000
BootConfig        0xBF040000  0x80500000  0x00040000  0x00000000
BootConfigSave    0xBF080000  0x80500000  0x00040000  0x00000000
KernelA           0xBF0C0000  0x80070000  0x00180000  0x80070008
RootFsA           0xBF240000  0x80500000  0x005C0000  0x00000000
KernelB           0xBF800000  0x80070000  0x00180000  0x80070008
RootFsB           0xBF980000  0x80500000  0x005C0000  0x00000000
Test              0xBFF40000  0x80500000  0x00040000  0x00000000
FIS directory     0xBFF80000  0xBFF80000  0x0003F000  0x00000000
RedBoot config    0xBFFBF000  0xBFFBF000  0x00001000  0x00000000
Board data        0xBFFC0000  0xBFFC0000  0x00040000  0x00000000

can I write only the KernelB and RootFsB part to try to test it, of if is not booting from memory it will not boot from flash either ?

LE: is there a way to backup the flash with redboot ?

Regards

(Last edited by jcook on 30 Jun 2016, 11:56)

Post #2
jcook
28 Jun 2016, 16:17

it seems that the telnet user/password is root/5up maybe I could hack it from within.

Regards

Post #3
jcook
29 Jun 2016, 21:13

I don't know how kernel partitions managed to get corrupted, I have backup for them, but if I flash them via redboot they will not boot. is there an image of redboot for platform atheros pb44 available somewhere ? I think u4ea redboot has some checks that prevent me from loading anything

regards!

Post #4
jcook
30 Jun 2016, 06:07

for future references..

the openwrt kernel entry point must be  0x80060000
still redboot has some hardcoded options boot related so it will not start without console access

Post #5
jcook
30 Jun 2016, 08:51

sorry for spamming
I managed to make it until the rootfs partition gets mounted and after that it hangs and resets

do I need to add something more to kernel cmd ?

[    0.000000] Linux version 4.4.14 (xxxi@droid) (gcc version 5.3.0 (Openwrt GCC 5.3.0 r792) ) #2 Thu Jun 30 07:12:35 U
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Atheros AR7161 rev 2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] No valid device tree found, continuing without
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=PB44 console=ttyS0,115200 ethaddr=01.4d.53.fd.ab.09 root=1f04 rootfstype=
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=000033a2
[    0.000000] Readback ErrCtl register=000033a2
[    0.000000] Memory: 59980K/65536K available (2923K kernel code, 113K rwdata, 724K rodata, 200K init, 579K bss, 55
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:600.000MHz, DDR:400.000MHz, AHB:150.000MHz, Ref:40.000MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000008] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 7158278654ns
[    0.007758] Calibrating delay loop... 398.13 BogoMIPS (lpj=1990656)
[    0.070472] pid_max: default: 32768 minimum: 301
[    0.075180] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.081778] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090882] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.101341] NET: Registered protocol family 16
[    0.106884] MIPS: machine is Atheros PB44 reference board
[    2.303925] registering PCI controller with io_map_base unset
[    4.419340] i2c-gpio i2c-gpio.0: using pins 1 (SDA) and 0 (SCL)
[    4.425479] PCI host bridge to bus 0000:00
[    4.429571] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[    4.436438] pci_bus 0000:00: root bus resource [io  0x0000]
[    4.441990] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    4.448762] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    4.457050] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[    4.463844] pci 0000:00:11.0: using irq 40 for pin 1
[    4.469486] clocksource: Switched to clocksource MIPS
[    4.475655] NET: Registered protocol family 2
[    4.480738] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    4.487696] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    4.494080] TCP: Hash tables configured (established 1024 bind 1024)
[    4.500515] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    4.506343] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    4.512810] NET: Registered protocol family 1
[    4.518095] futex hash table entries: 256 (order: -1, 3072 bytes)
[    4.536583] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    4.542453] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    4.554304] io scheduler noop registered
[    4.558227] io scheduler deadline registered (default)
[    4.563580] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    4.570311] console [ttyS0] disabled
[    4.593878] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 9375000) is a 16550A
[    4.602476] console [ttyS0] enabled
[    4.602476] console [ttyS0] enabled
[    4.609410] bootconsole [early0] disabled
[    4.609410] bootconsole [early0] disabled
[    4.619032] ath79-spi ath79-spi: can't setup spi0.1, status -517
[    4.625074] ath79-spi ath79-spi: can't create new device for spi-vsc7385
[    4.632346] m25p80 spi0.0: found m25p128, expected m25p64
[    4.637731] m25p80 spi0.0: m25p128 (16384 Kbytes)
[    4.643165] Searching for RedBoot partition table in spi0.0 at offset 0xf80000
[    5.049305] 11 RedBoot partitions found on MTD device spi0.0
[    5.054962] Creating 11 MTD partitions on "spi0.0":
[    5.059834] 0x000000000000-0x000000040000 : "RedBoot"
[    5.066066] 0x000000040000-0x000000080000 : "BootConfig"
[    5.072722] 0x000000080000-0x0000000c0000 : "BootConfigSave"
[    5.079677] 0x0000000c0000-0x000000240000 : "KernelA"
[    5.085976] 0x000000240000-0x000000800000 : "RootFsA"
[    5.092350] 0x000000800000-0x000000980000 : "KernelB"
[    5.098668] 0x000000980000-0x000000f40000 : "RootFsB"
[    5.105041] 0x000000f40000-0x000000f79000 : "Test"
[    5.111157] 0x000000f80000-0x000000fbf000 : "FIS directory"
[    5.118008] 0x000000fbf000-0x000000fc0000 : "RedBoot config"
[    5.125007] 0x000000fc0000-0x000001000000 : "Board data"
[    5.135543] libphy: ag71xx_mdio: probed
[    5.460923] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=00070421, driver=Generic PHY]
[    5.470666] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    5.791381] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[    5.798853] NET: Registered protocol family 10
[    5.806005] NET: Registered protocol family 17
[    5.810559] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_
[    5.823238] 8021q: 802.1Q VLAN Support v1.8
[    5.840075] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    5.847637] Freeing unused kernel memory: 200K (8040e000 - 80440000)
[    6.981193] init: Console is alive
[    6.984753] init: - watchdog -
[    8.720529] usbcore: registered new interface driver usbfs
[    8.726088] usbcore: registered new interface driver hub
[    8.731490] usbcore: registered new device driver usb
[    8.738500] gpio-keys-polled gpio-keys-polled: unable to claim gpio 22, err=-517
[    8.748314] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    8.755860] ehci-platform: EHCI generic platform driver
[    8.761190] ehci-platform ehci-platform: EHCI Host Controller
[    8.766939] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    8.774936] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    8.799506] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    8.806528] hub 1-0:1.0: USB hub found
[    8.810549] hub 1-0:1.0: 2 ports detected
[    8.815048] gpio-keys-polled gpio-keys-polled: unable to claim gpio 22, err=-517
[    8.824357] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    8.831651] ohci-platform: OHCI generic platform driver
[    8.836950] ohci-platform ohci-platform: Generic Platform OHCI controller
[    8.843769] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
+ VSCXXX Found 0  unit 0:0  phy_addr: 0  id: 00070421
 PHY is Vitesse VSC8601 Rev B
VSCXXX unit 0  phy_addr 0
 mode_ctr        (00 )=1140     auto-eg
    full-duplex
    f1000
 mode_status     (01 )=7949     auto-neg-cap
    ex-cap
  rcv-error       (19 )=0000
  false-carrier   (20 )=0000
  disconnect_cnt  (21 )=0000


LE:
Disabling ath79_register_usb(); in mach-pb44.c did the trick

[    5.236728] init: - watchdog -
[    6.971889] usbcore: registered new interface driver usbfs
[    6.977498] usbcore: registered new interface driver hub
[    6.982891] usbcore: registered new device driver usb
[    6.989907] gpio-keys-polled gpio-keys-polled: unable to claim gpio 22, err=-517
[    6.999719] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.007262] ehci-platform: EHCI generic platform driver
[    7.014674] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    7.021861] ohci-platform: OHCI generic platform driver
[    7.037646] init: - preinit -
[    7.990958] eth1: link up (1000Mbps/Full duplex)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

[   10.788941] mount_root: mounting /dev/root
[   10.812228] eth1: link down
[   10.824179] procd: - early -
[   10.827132] procd: - watchdog -
[   11.459743] procd: - ubus -
[   11.512563] random: ubusd urandom read with 18 bits of entropy available
[   11.520491] procd: - init -
Please press Enter to activate this console.
[   11.733611] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   11.751636] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
[   11.759221] Backport generated by backports.git backports-20160216-0-ge3c56e4
[   11.768862] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.782163] nf_conntrack version 0.5.0 (940 buckets, 3760 max)
[   11.816275] xt_time: kernel timezone is -0000
[   11.865308] PPP generic driver version 2.4.2
[   11.871936] NET: Registered protocol family 24
[   11.905401] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[   13.480692] ieee80211 phy0: Atheros AR9160 MAC/BB Rev:1 AR2133 RF Rev:b0 mem=0xb0000000, irq=40
[   13.491710] gpio-keys-polled gpio-keys-polled: unable to claim gpio 22, err=-517

uci: Entry not found


BusyBox v1.24.2 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
 /________/  LE  \  |____|___|___/|___|                      lede-project.org
 \        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (HEAD, r821)
    \________\/    -----------------------------------------------------------

root@(none):/# [   80.781929] random: nonblocking pool is initialized

(Last edited by jcook on 30 Jun 2016, 11:54)

Post #6
Slimey
25 Nov 2017, 16:57

Can you be so kind as to send me a complete mtd dump sir? A dump of the router running openwrt please smile

(Last edited by Slimey on 25 Nov 2017, 17:01)

Post #7
Slimey
3 Jan 2018, 18:46

jcook ?

The discussion might have continued from here.