Good morning everyone!,well by mistake, I bricked my MR3020 Rev: 1.2 by flashing my backup mtd2.bin, failsafe mode do not working and even tpl command after autoboot doesnt work with serial, once I keep pressing wps button while plugging in power it ends up inside the TFTP auto update firmware, but I got always the same error with all firmwares i'd tried [product id verify fail!], so any help will be greatly appreciated, thank you in advance!


Boot Log: 

U-Boot 1.1.4-gd0be0bfd (Sep 29 2013 - 10:06:31)

AP121 (ar9330) U-boot

DRAM:  32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup 
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup 
eth1 up
eth0, eth1
auto update firmware: is_auto_upload_firmware = 0!
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... Stream with EOS marker is not supportedLZMA ERROR 1 - must RESET 

U-Boot 1.1.4-gd0be0bfd (Sep 29 2013 - 10:06:31)

AP121 (ar9330) U-boot

DRAM:  32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

Boot Log: while pressing wps button

U-Boot 1.1.4-gd0be0bfd (Sep 29 2013 - 10:06:31)

AP121 (ar9330) U-boot

DRAM:  32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash:  4 MB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup 
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup 
eth1 up
eth0, eth1
auto update firmware: is_auto_upload_firmware = 1!
eth1 link down
eth0 link down
Using eth1 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'mr3020v1_tp_recovery.bin'.
Load address: 0x80800000
Loading: *#################################################################
     #################################################################
     #################################################################
     #################################################################
     #################################################################
     #################################################################
     #################################################################
     #################################################################
     ###############################
done
Bytes transferred = 2818052 (2b0004 hex)
auto update firmware: product id verify fail!
Autobooting in 1 seconds
## Booting image at 9f020000 ...
   Uncompressing Kernel Image ... Stream with EOS marker is not supportedLZMA ERROR 1 - must RESET