1 (edited by ErwinH 2015-06-24 17:53:08)

Topic: Sitecom WLR-7100

I've got a WLR-7100, and I thought I would help the community by getting the bootlogs for this device. Unfortunately it won't allow me to boot with the serial port connected. But if I disconnect the port before boot and reconnect it after I powered the router it gives me a partial bootlog. I hope this is enough.

If I boot with the cable connected it returns this information:

U-Boot 2.0.0 (May 22 2013 - 13:25:23)
Board:MI124

sri
Wasp 1.1
wasp_ddr_initial_config(276): Wasp (16bit) ddr1 init
wasp_ddr_initial_config(426): Wasp ddr init done
DRAM: 4 MB
Top of RAM usable for U-Boot at: 80400000
Reserving 236k for U-Boot at: 803c4000
Reserving 192k for malloc() at: 80394000
Reserving 44 Bytes for Board Info at: 80393fd4
Reserving 36 Bytes for Global Data at: 80393fb0
Reserving 128k for boot params() at: 80373fb0
Stack Pointer at: 80373f98

The partial bootlog:

ag934x_enet_initialize...
No valid address in Flash. Using fixed address
 wasp  reset mask:c03300
WASP  ----> S17 PHY *
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
    3     2     1     0

3: System Boot system code via Flash.
## Booting image at 9f040000 ...
   Image Name:   Linux Kernel Image
   Created:      2014-10-15   4:15:19 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1835780 Bytes =  1.8 MB
   Load Address: 80002000
   Entry Point:  80006110
   Verifying Checksum at 0x9f040040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80006110) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

Booting Atheros AR934x

 init started: BusyBox v1.7.5 (2014-10-15 12:11:05 CST)

starting pid 809, tty '/dev/console': '/sbin/config_init'
mknod: /dev/ttyS0: File exists
mknod: /dev/ttyS1: File exists
Config Init version: 1.7.3.8 date: 2014/10/15
Wed Jan  1 00:00:00 UTC 2014
ln: /lib/./modules: File exists
insmod: can't open '/lib/ar8327_drv.ko': No such file or directory

starting pid 864, tty '/dev/ttyS0': '/sbin/config_term'
************************************************************************
*                                 WLR-7100                             *
************************************************************************

KernelApp/Ramdisk Ver:1.7.3.8                    Date:2014/10/15
password:

Printenv

ar7240> printev   nv

bootdelay=4
baudrate=115200
ethaddr="64:D1:A3:26:9F:0C"
sn=14C222661
hw_ver=1.0.0
hw_id=02261055
pro_id=000
country=000
domain=1
op_mode=0
wanaddr=64:D1:A3:26:9F:0E
wlanaddr=00:AA:BB:CC:DD:12
snextra=14C222661***********
bootfile=uImage
dir=
bc=mi124_f1e
lu=tftp 0x80060000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize;cp.b
$fileaddr 0x9f000000 $filesize
lf=tftp 0x80060000 ${dir}${bc}-jffs2&&erase 0x9f050000 +$filesize;cp.b
$fileaddr 0x9f050000 $filesize
lk=tftp 0x80060000 ${dir}vmlinux_${bc}.lzma.uImage&&erase 0x9f300000
+$filesize;cp.b $fileaddr 0x9f300000 $filesize
ethact=eth0
bootargs=console=ttyS0,115200 root=31:03 rootfstype=jffs2
init=/sbin/init
mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),896k(uImage),6912k(rootfs),64k(NVRAM),64k(ART)
ipaddr=192.168.99.9
serverip=192.168.99.8
uboot_ver=2.0.0.3
stdin=serial
stdout=serial
stderr=serial

Environment size: 855/65532 bytes

What extra information is necessary to get OpenWRT support for this device?

Re: Sitecom WLR-7100

Today I tried the run the uImage's both from BB and CC (ar71xx), but both won't boot.

## Booting image at 80800000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.14
   Created:      2015-06-09  21:39:15 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1192789 Bytes =  1.1 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x80800040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 3.18.14 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45872) ) #1 Sun Jun 7 16:22:32 CEST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ath-nor0:192k(u-boot),64k(u-boot-env),896k(uImage),6912k(rootfs),64k(NVRAM),64k(ART) mem=64M rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 60812K/65536K available (2627K kernel code, 131K rwdata, 544K rodata, 208K init, 194K bss, 4724K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.100000] NET: Registered protocol family 16
[    0.100000] MIPS: machine is Generic AR71XX/AR724X/AR913X based board
[    0.110000] Switched to clocksource MIPS
[    0.120000] NET: Registered protocol family 2
[    0.120000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.120000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.130000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.130000] TCP: reno registered
[    0.140000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.140000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.150000] NET: Registered protocol family 1
[    0.150000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.180000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.180000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.190000] msgmni has been set to 118
[    0.210000] io scheduler noop registered
[    0.210000] io scheduler deadline registered (default)
[    0.220000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.220000] console [ttyS0] disabled
[    0.250000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.260000] console [ttyS0] enabled
[    0.260000] console [ttyS0] enabled
[    0.260000] bootconsole [early0] disabled
[    0.260000] bootconsole [early0] disabled
[    0.280000] TCP: cubic registered
[    0.280000] NET: Registered protocol family 17
[    0.280000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.300000] Bridge firewalling registered
[    0.300000] 8021q: 802.1Q VLAN Support v1.8
[    0.320000] VFS: Cannot open root device "31:03" or unknown-block(31,3): error -6
[    0.330000] Please append a correct "root=" boot option; here are the available partitions:
[    0.340000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
[    0.340000] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)

Now I have to find the next steps.

Re: Sitecom WLR-7100

More progress. I've booted the AP135-020 initramfs image. Network and Wireless gets detected.

[    0.000000] Linux version 3.10.49 (erwin@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45951) ) #6 Sat Jun 27 19:34:37 CEST 2015
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=AP135-020 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,14528k(rootfs),1472k(kernel),64k(art)ro,16000k@0x50000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59288k/65536k available (2239k kernel code, 6248k reserved, 603k data, 2212k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Atheros AP135-020 reference board
[    0.300000] ar71xx: invalid PHY interface mode for GE1
[    0.310000] registering PCI controller with io_map_base unset
[    0.320000] bio: create slab <bio-0> at 0
[    0.330000] PCI host bridge to bus 0000:00
[    0.330000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.340000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.350000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    0.350000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref]
[    0.360000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.360000] Switching to clocksource MIPS
[    0.370000] NET: Registered protocol family 2
[    0.370000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.370000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.380000] TCP: Hash tables configured (established 512 bind 512)
[    0.380000] TCP: reno registered
[    0.390000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.400000] NET: Registered protocol family 1
[    3.040000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    3.050000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    3.060000] msgmni has been set to 115
[    3.060000] io scheduler noop registered
[    3.070000] io scheduler deadline registered (default)
[    3.070000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    3.100000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    3.110000] console [ttyS0] enabled, bootconsole disabled
[    3.110000] console [ttyS0] enabled, bootconsole disabled
[    3.120000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    3.130000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    3.130000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    3.140000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.150000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.150000] mtd: spi0.0: skipping zero sized partition
[    3.160000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.160000] mtd: spi0.0: skipping zero sized partition
[    3.170000] mtd: spi0.0: partitioning exceeds flash size, truncating
[    3.180000] 4 cmdlinepart partitions found on MTD device spi0.0
[    3.180000] Creating 4 MTD partitions on "spi0.0":
[    3.190000] 0x000000000000-0x000000040000 : "u-boot"
[    3.190000] 0x000000040000-0x000000050000 : "u-boot-env"
[    3.200000] 0x000000050000-0x000000800000 : "rootfs"
[    3.210000] mtd: device 2 (rootfs) set to be root filesystem
[    3.210000] mtdsplit: no squashfs found in "rootfs"
[    3.220000] mtdsplit: no squashfs found in "spi0.0"
[    3.230000] 0x000000050000-0x000000800000 : "firmware"
[    3.260000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[    4.460000] libphy: ag71xx_mdio: probed
[    5.010000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    5.030000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    5.040000] TCP: cubic registered
[    5.040000] NET: Registered protocol family 17
[    5.040000] 8021q: 802.1Q VLAN Support v1.8
[    5.060000] Freeing unused kernel memory: 2212K (80327000 - 80550000)
procd: Console is alive
procd: - watchdog -
[    5.110000] usbcore: registered new interface driver usbfs
[    5.110000] usbcore: registered new interface driver hub
[    5.120000] usbcore: registered new device driver usb
[    5.130000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    5.140000] ehci-platform: EHCI generic platform driver
[    5.140000] ehci-platform ehci-platform: EHCI Host Controller
[    5.150000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    5.160000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    5.190000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    5.190000] hub 1-0:1.0: USB hub found
[    5.200000] hub 1-0:1.0: 1 port detected
[    5.200000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[    9.690000] NET: Registered protocol family 10
[    9.700000] nf_conntrack version 0.5.0 (960 buckets, 3840 max)
[    9.710000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.730000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[    9.740000] Backport generated by backports.git backports-20140320-37-g5c33da0
[    9.770000] cfg80211: Calling CRDA to update world regulatory domain
[    9.770000] cfg80211: World regulatory domain updated:
[    9.780000] cfg80211:  DFS Master region: unset
[    9.780000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[    9.790000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    9.800000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[    9.810000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[    9.820000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[    9.830000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    9.830000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[    9.840000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[    9.850000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[    9.930000] ath10k_pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit]
[    9.940000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   10.250000] ath10k: pci irq legacy irq_mode 0 reset_mode 0
[   10.340000] ath10k: otp stream is empty, using board.bin contents
[   11.170000] ath10k: qca988x hw2.0 (0x4100016c, 0x043222ff) fw 10.1.467.2-1 api 2 htt 2.1
[   11.710000] cfg80211: Calling CRDA for country: US
[   11.720000] cfg80211: Regulatory domain changed to country: US
[   11.720000] cfg80211:  DFS Master region: FCC
[   11.730000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   11.740000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[   11.740000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[   11.750000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[   11.760000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[   11.770000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[   11.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   11.880000] xt_time: kernel timezone is -0000
[   11.910000] PPP generic driver version 2.4.2
[   11.940000] NET: Registered protocol family 24
[   11.980000] ieee80211 phy1: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
procd: - init complete -
[   19.500000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   21.010000] eth0: link up (1000Mbps/Full duplex)
[   21.030000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



BusyBox v1.22.1 (2015-06-26 11:59:06 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Barrier Breaker, r45951)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/# 

Next step is to create the profile for this device.

Re: Sitecom WLR-7100

I'm in the progress of building an image for this device. The image itself is working fine, but I have some troubles creating an image which can be flashed.

One of the issues I'm facing is the fact that the uImage-partition is only: 896k(uImage), but when I run make the uImage is 1054473 bytes big which is well over 896k.

When I change the mtdpartitions in the config to 1088k I get a sysupgrade image. Can I flash that (with MTD) without any issues, or will I brick my device doing so?

5 (edited by ErwinH 2015-07-03 16:50:11)

Re: Sitecom WLR-7100

Made some progress. Booted the initramfs image, with working switch. Flashed with mtd -r write sysupgrade.bin and got a booting router.

[    0.000000] Linux version 3.10.49 (erwin@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r45951) ) #1 Fri Jul 3 10:06:40 CEST 2015
[    0.000000] MyLoader: sysp=c095e295, boardp=26b4ea94, parts=aaa6a084
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9342 rev 1
[    0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8030e9b0, node_mem_map 81000000
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  board=WLR7100 console=ttyS0,115200 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,1088k(kernel),6720k(rootfs),64k(nvram)ro,64k(art)ro,7808k@0x40000(firmware) rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61272k/65536k available (2232k kernel code, 4264k reserved, 602k data, 236k init, 0k highmem)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[    0.080000] pid_max: default: 32768 minimum: 301
[    0.080000] Mount-cache hash table entries: 512
[    0.090000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Sitecom WLR-7100
[    0.100000] ar71xx: using random MAC address for eth0
[    0.310000] bio: create slab <bio-0> at 0
[    0.320000] Switching to clocksource MIPS
[    0.330000] NET: Registered protocol family 2
[    0.330000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[    0.330000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[    0.340000] TCP: Hash tables configured (established 512 bind 512)
[    0.340000] TCP: reno registered
[    0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.360000] NET: Registered protocol family 1
[    0.360000] PCI: CLS 0 bytes, default 32
[    0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.380000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.390000] msgmni has been set to 119
[    0.400000] io scheduler noop registered
[    0.400000] io scheduler deadline registered (default)
[    0.410000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.440000] console [ttyS0] enabled, bootconsole disabled
[    0.450000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[    0.460000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.470000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[    0.470000] 7 cmdlinepart partitions found on MTD device spi0.0
[    0.480000] Creating 7 MTD partitions on "spi0.0":
[    0.490000] 0x000000000000-0x000000030000 : "u-boot"
[    0.490000] 0x000000030000-0x000000040000 : "u-boot-env"
[    0.500000] 0x000000040000-0x000000150000 : "kernel"
[    0.510000] 0x000000150000-0x0000007e0000 : "rootfs"
[    0.510000] mtd: device 3 (rootfs) set to be root filesystem
[    0.520000] 1 squashfs-split partitions found on MTD device rootfs
[    0.530000] 0x000000330000-0x0000007e0000 : "rootfs_data"
[    0.530000] 0x0000007e0000-0x0000007f0000 : "nvram"
[    0.540000] 0x0000007f0000-0x000000800000 : "art"
[    0.550000] 0x000000040000-0x0000007e0000 : "firmware"
[    0.570000] libphy: ag71xx_mdio: probed
[    0.600000] switch0: Atheros AR8337 rev. 2 switch registered on ag71xx-mdio.0
[    1.800000] libphy: ag71xx_mdio: probed
[    2.350000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd036, driver=Atheros AR8216/AR8236/AR8316]
[    2.360000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[    2.370000] TCP: cubic registered
[    2.380000] NET: Registered protocol family 17
[    2.380000] 8021q: 802.1Q VLAN Support v1.8
[    2.400000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    2.400000] Freeing unused kernel memory: 236K (80325000 - 80360000)
[    4.790000] usbcore: registered new interface driver usbfs
[    4.790000] usbcore: registered new interface driver hub
[    4.800000] usbcore: registered new device driver usb
[    4.810000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.820000] ehci-platform: EHCI generic platform driver
[    4.820000] ehci-platform ehci-platform: EHCI Host Controller
[    4.830000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.840000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    4.870000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    4.870000] hub 1-0:1.0: USB hub found
[    4.880000] hub 1-0:1.0: 1 port detected
[    4.880000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    8.720000] jffs2: notice: (346) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of xref (0 dead, 2 orphan) found.
[   10.330000] NET: Registered protocol family 10
[   10.350000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
[   10.360000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.380000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[   10.380000] Backport generated by backports.git backports-20140320-37-g5c33da0
[   10.430000] cfg80211: Calling CRDA to update world regulatory domain
[   10.430000] cfg80211: World regulatory domain updated:
[   10.440000] cfg80211:  DFS Master region: unset
[   10.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   10.450000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.460000] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   10.470000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   10.480000] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[   10.490000] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.490000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   10.500000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   10.510000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   10.580000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.640000] xt_time: kernel timezone is -0000
[   10.650000] PPP generic driver version 2.4.2
[   10.660000] NET: Registered protocol family 24
[   18.800000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.810000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[   18.810000] device eth0.1 entered promiscuous mode
[   18.820000] device eth0 entered promiscuous mode
[   18.830000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   18.870000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[   20.590000] eth0: link up (1000Mbps/Full duplex)
[   20.600000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   20.610000] br-lan: port 1(eth0.1) entered forwarding state
[   20.610000] br-lan: port 1(eth0.1) entered forwarding state
[   20.620000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[   20.620000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[   20.640000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   22.610000] br-lan: port 1(eth0.1) entered forwarding state

Now I need to get the wifi-adapters working again.

Re: Sitecom WLR-7100

and you made progress
i have bought also a sitecom wlr 7100 and want to install opnwrt on it if its possible...

are you happy about the router his performance ?

grtz