Hope u still can help me
I've tried to use ur firmware and run firstboot - its great, most problems solved, thank u! But WiFi is still offline.
WiFi Config:
config wifi-device radio0
option type mac80211
option channel 11
option hwmode 11g
option path 'platform/ar933x_wmac'
option htmode HT20
option disabled 0
option country UA
config wifi-iface
option device radio0
option network lan
option mode ap
option ssid OpenWrt
option encryption none
IW-logs:
root@OpenWrt:~# iwinfo
wlan0 ESSID: "OpenWrt"
Access Point: 00:11:33:22:44:55
Mode: Master Channel: 11 (2.462 GHz)
Tx-Power: 18 dBm Link Quality: unknown/70
Signal: unknown Noise: -95 dBm
Bit Rate: unknown
Encryption: none
Type: nl80211 HW Mode(s): 802.11bgn
Hardware: unknown [Generic MAC80211]
TX power offset: unknown
Frequency offset: unknown
Supports VAPs: yes PHY name: phy0
root@OpenWrt:~# iw list
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x1 RX 0x1
Configured Antennas: TX 0x1 RX 0x1
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
* mesh point
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x116e
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-7
Frequencies:
* 2412 MHz [1] (18.0 dBm)
* 2417 MHz [2] (18.0 dBm)
* 2422 MHz [3] (18.0 dBm)
* 2427 MHz [4] (18.0 dBm)
* 2432 MHz [5] (18.0 dBm)
* 2437 MHz [6] (18.0 dBm)
* 2442 MHz [7] (18.0 dBm)
* 2447 MHz [8] (18.0 dBm)
* 2452 MHz [9] (18.0 dBm)
* 2457 MHz [10] (18.0 dBm)
* 2462 MHz [11] (18.0 dBm)
* 2467 MHz [12] (18.0 dBm)
* 2472 MHz [13] (18.0 dBm)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed, WDS } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match
* #{ IBSS, AP, mesh point } <= 1,
total <= 1, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Many many thanks for any help!
(Last edited by exxiiss on 20 Jun 2015, 17:56)