Re: NuCom R5010UN ADSL router

@jakapaka: Can you post how you replaced the bootloader?

Re: NuCom R5010UN ADSL router

suso wrote:

@jakapaka: Can you post how you replaced the bootloader?

Yes, as @danitool pointed out, I used the CFE-installable update (dummy_firmware) as any other firmware image. I used the HTTP method to 192.168.1.1.

After that, again from CFE I installed the openwrt image. Notice that the background on the HTTP CFE form is now gray and not white.

53 (edited by suso 2015-11-28 00:55:27)

Re: NuCom R5010UN ADSL router

@danitool: I don't know how but you did it again man! When flashing first CFE-R5010UNv2-mod-dummy_firmware.bin and then openwrt-R5010UNv2-squashfs-cfe-r47603.bin the messages coming out of the serial port were not exactly promising. On the contrary. Worrying is a better word. Only the SQUASHFS errors had disappeared straight away.

But when it finally booted the result is amazing. Judge for yourself:

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 2.0.3 for BCM96328 (32bit,SP,BE)
Build Date: Thu Nov 26 15:09:04 CET 2015 (dani@tool)
Copyright (C) 2000-2009 Broadcom Corporation.

HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
** HELLO **

Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-5)                    : 96328ang  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : fa:ba:da:fa:ba:da  
PSI Size (1-64) KBytes            : 32  
Enable Backup PSI [0|1]           : 1  
System Log Size (0-256) KBytes    : 0  
Main Thread Number [0|1]          : 0  
Voice Board Configuration (0-11)  : LE88276  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xb8010000) ...
Code Address: 0x80A00000, Entry Address: 0x80a00000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80a00000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
13 buffers found.
Closing DMA Channels.
Starting program at 0x80a00000
[    0.000000] Linux version 4.1.11 (dani@tool) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 r47603) ) #3 Tue Nov 24 17:21:51 CET 2015
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-106.24
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: 96328ang
[    0.000000] MIPS: machine is NuCom R5010UN v2
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59652K/65536K available (2974K kernel code, 140K rwdata, 604K rodata, 1264K init, 193K bss, 5884K reserved, 0K cma-reserved)
[    0.000000] NR_IRQS:256
[    0.000000] clocksource MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945377789 ns
[    0.000019] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421772796ns
[    0.008684] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.051004] pid_max: default: 32768 minimum: 301
[    0.056428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.063223] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.078206] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.089949] NET: Registered protocol family 16
[    0.330936] registering PCI controller with io_map_base unset
[    0.362253] PCI host bridge to bus 0000:00
[    0.366503] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.373569] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.380552] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.387539] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.396330] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.405804] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.412825] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f07fff 64bit]
[    0.420359] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.425448] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.434066] Switched to clocksource MIPS
[    0.441475] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.447352] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.453199] bcma: bus0: Found chip with id 43227, rev 0x01 and package 0x09
[    0.460401] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x27, class 0x0)
[    0.469221] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
[    0.478152] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x14, class 0x0)
[    0.502367] bcma: bus0: Bus registered
[    0.506861] NET: Registered protocol family 2
[    0.513600] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.520877] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.527470] TCP: Hash tables configured (established 1024 bind 1024)
[    0.534509] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.540607] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.547843] NET: Registered protocol family 1
[    0.554923] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.565728] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.571793] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.585495] io scheduler noop registered
[    0.589589] io scheduler deadline registered (default)
[    0.596977] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.606642] console [ttyS0] enabled
[    0.606642] console [ttyS0] enabled
[    0.613796] bootconsole [early0] disabled
[    0.613796] bootconsole [early0] disabled
[    0.631165] m25p80 spi1.0: found s25fl128s, expected m25p80
[    0.636938] m25p80 spi1.0: s25fl128s (16384 Kbytes)
[    0.642584] bcm63xxpart: CFE boot tag found with version 6 and board type 96328ang
[    0.650478] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.657123] bcm63xxpart: Partition 1 is kernel offset 10100 and length 13bf0c
[    0.664458] bcm63xxpart: Partition 2 is rootfs offset 14c00c and length ea3ff4
[    0.671886] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[    0.679141] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[    0.686397] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.692486] Creating 5 MTD partitions on "spi1.0":
[    0.697433] 0x000000000000-0x000000010000 : "CFE"
[    0.704168] 0x000000010100-0x00000014c00c : "kernel"
[    0.711089] 0x00000014c00c-0x000000ff0000 : "rootfs"
[    0.717870] mtd: device 2 (rootfs) set to be root filesystem
[    0.727510] 1 squashfs-split partitions found on MTD device rootfs
[    0.733924] 0x000000330000-0x000000ff0000 : "rootfs_data"
[    0.741295] 0x000000ff0000-0x000001000000 : "nvram"
[    0.748111] 0x000000010000-0x000000ff0000 : "linux"
[    0.791348] b53_common: found switch: BCM63xx, rev 0
[    0.797034] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.807039] NET: Registered protocol family 10
[    0.818895] NET: Registered protocol family 17
[    0.823650] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.836684] 8021q: 802.1Q VLAN Support v1.8
[    0.855102] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.879442] Freeing unused kernel memory: 1264K (803b4000 - 804f0000)
[    2.720659] init: Console is alive
[    2.724505] init: - watchdog -
[    4.528453] usbcore: registered new interface driver usbfs
[    4.534374] usbcore: registered new interface driver hub
[    4.540106] usbcore: registered new device driver usb
[    4.559721] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.569110] ehci-platform: EHCI generic platform driver
[    4.678128] ehci-platform ehci-platform: EHCI Host Controller
[    4.684114] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    4.692643] ehci-platform ehci-platform: irq 50, io mem 0xb0002500
[    4.710109] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[    4.720224] hub 1-0:1.0: USB hub found
[    4.724697] hub 1-0:1.0: 1 port detected
[    4.736368] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.745549] ohci-platform: OHCI generic platform driver
[    4.751174] ohci-platform ohci-platform: Generic Platform OHCI controller
[    4.758239] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[    4.766554] ohci-platform ohci-platform: irq 49, io mem 0xb0002600
[    4.832096] hub 2-0:1.0: USB hub found
[    4.836601] hub 2-0:1.0: 1 port detected
[    4.850116] init: - preinit -
[    5.546885] random: procd urandom read with 104 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    9.055356] random: nonblocking pool is initialized
[    9.077039] jffs2: notice: (247) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.096285] mount_root: switching to jffs2 overlay
ifconfig: SIOCGIFFLAGS: No such device
[    9.145947] procd: - early -
[    9.149252] procd: - watchdog -
[   10.130538] procd: - ubus -
[   11.144273] procd: - init -
Please press Enter to activate this console.
[   12.384105] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.413980] Loading modules backported from Linux version master-2015-10-26-0-g28c26cb
[   12.422170] Backport generated by backports.git backports-20150903-4-g12cf266
[   12.435833] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.463703] nf_conntrack version 0.5.0 (951 buckets, 3804 max)
[   12.539576] xt_time: kernel timezone is -0000
[   12.598720] cfg80211: World regulatory domain updated:
[   12.604028] cfg80211:  DFS Master region: unset
[   12.608476] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.618523] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.626762] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.635004] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   12.643251] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.653019] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.662781] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   12.671111] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   12.679354] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   12.810416] PPP generic driver version 2.4.2
[   12.819822] NET: Registered protocol family 24
[   12.877817] b43-phy0: Broadcom 43227 WLAN found (core revision 30)
[   12.885019] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 17
[   12.891414] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 14, Version 0
[   12.900049] Broadcom 43xx driver loaded [ Features: PNL ]
[   17.474421] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   24.138416] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   24.163301] device eth0.1 entered promiscuous mode
[   24.168281] device eth0 entered promiscuous mode
[   24.187843] br-lan: port 1(eth0.1) entered forwarding state
[   24.193660] br-lan: port 1(eth0.1) entered forwarding state
[   26.194085] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.24.1 (2015-11-24 12:42:11 CET) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 DESIGNATED DRIVE\F2*\91\9D\95\B1 r47603)
 -----------------------------------------------------
  * 2 oz. Orange Juice         Combine all juices in a
  * 2 oz. Pineapple Juice      tall glass filled with
  * 2 oz. Grapefruit Juice     ice, stir well.
  * 2 oz. Cranberry Juice
 -----------------------------------------------------
root@OpenWrt:/# 

A new file created in /etc was still there after reboot. However there is still a lot the be tested.

As everybody is now able to update the firmware of this router with OpenWrt in 5 minutes without even connecting the serial port, perhaps it's worth mentioning that after flashing telnet seems disabled and you get into the router issuing this command:

ssh root@192.168.1.1

I think I might try to build the firmware myself to tweak busybox e.g. Any recommendations as to how to do that? I built firmware for a few devices already so I know how to run make menuconfig and I know there are quite a few options to choose from there... Do you know how to add this device to https://wiki.openwrt.org/toh/start?

Dani for president! At one point it seemed as if you'd given up and I was about to trash the router, but you came back and how! Thanks again.

Re: NuCom R5010UN ADSL router

Good news. This device is now officially supported by Openwrt
https://dev.openwrt.org/changeset/47697

Firmware also available at:
https://downloads.openwrt.org/snapshots … fs-cfe.bin

Regards and happy hacking.

Re: NuCom R5010UN ADSL router

I managed to compile a working firmware with ffmpeg, lighttpd, ssmtp, a powerful busybox, etc... Dhcp server, dns server, dropbear server, Wi-Fi and USB flash drive work. OpenWrt rocks!

@jakapaka: there is a USB port so if you have an 802.11n capable Wi-Fi dongle just plug it in and compile the appropriate driver into the firmware and you are ready to go.

@danitool: thanks again for your effort. Shouldn't this device be added to https://wiki.openwrt.org/toh/hwdata/nucom/start and/or to https://wiki.openwrt.org/toh/start?

Re: NuCom R5010UN ADSL router

Hi, I have a problem with this router, opkg is not working and idk why.
It has internet connection as you can see, and it won't do anything else than that.
I have changed repositories and it won't work too.

https://i.gyazo.com/e029f6ed189ab4050dbf61339908c755.png

Any idea of what could fix that?
Also how could I change IPs so that when I turn it off it doesn't reset?.

Thx guys! big_smile

Re: NuCom R5010UN ADSL router

You have connectivity towards the DNS servers. But what's the configuration for the DNS?

> cat /tmp/resolv.conf.auto

58 (edited by BernoO 2016-09-05 23:06:19)

Re: NuCom R5010UN ADSL router

First post, long OpenWRT user.

Thanks to all for this work. I have and Nucom R5000UN version (from Movistar company here in Chile), and this ADSL Router shares some things with this model; the CPU (BCM63281), specs like SPI and RAM but not the same model (SPI in this specific R5000 is an MXIC mx25l12845emi-10g and Winbond 64 MB of RAM), and different WiFi Chip (BCM43225).

This Nucon R5000UN also is identical to a Dlink Router (DSL-2750U T1 rev.) and on this post...

h**ps://forum.openwrt.org/viewtopic.php?id=3362 (As first post, no links allowed)

...describes the same issue as R5010UN. Firmware can be loaded via CFE, but settings are not saved, and this also happen with R5000UN. So, with a gifted router and nothing to lose, i cross fingers and use the CFE update from danitool.

It worked! Firmware used was from Comtrend AR-5387un. Got Wifi working(802.11G sadly...but hey..) as client. Rest (USB, VLAN, Leds) still is untested.

Here is System Log

Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.040000] pid_max: default: 32768 minimum: 301
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.060000] NET: Registered protocol family 16
Tue Mar  1 09:16:57 2016 kern.warn kernel: [    0.296000] registering PCI controller with io_map_base unset
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.316000] PCI host bridge to bus 0000:00
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.320000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.324000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.328000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.332000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.332000] pci 0000:00:00.0: PME# supported from D0 D3hot
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.332000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.336000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.336000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.336000] pci 0000:01:00.0: supports D1 D2
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.336000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.336000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.336000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.340000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.344000] pci 0000:00:00.0: PCI bridge to [bus 01]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.348000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.352000] Switched to clocksource MIPS
Tue Mar  1 09:16:57 2016 kern.warn kernel: [    0.356000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
Tue Mar  1 09:16:57 2016 kern.warn kernel: [    0.364000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.368000] bcma: bus0: Found chip with id 43225, rev 0x01 and package 0x0A
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.376000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.384000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.392000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
Tue Mar  1 09:16:57 2016 kern.warn kernel: [    0.528000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.556000] bcma: bus0: Bus registered
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.560000] NET: Registered protocol family 2
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.568000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.576000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.580000] TCP: Hash tables configured (established 1024 bind 1024)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.588000] TCP: reno registered
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.592000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.596000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.604000] NET: Registered protocol family 1
Tue Mar  1 09:16:57 2016 kern.debug kernel: [    0.608000] PCI: CLS 0 bytes, default 16
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.612000] futex hash table entries: 256 (order: -1, 3072 bytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.624000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.636000] msgmni has been set to 117
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.640000] io scheduler noop registered
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.644000] io scheduler deadline registered (default)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.652000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.660000] console [ttyS0] enabled
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.668000] bootconsole [early0] disabled
Tue Mar  1 09:16:57 2016 kern.warn kernel: [    0.680000] m25p80 spi1.0: found mx25l12805d, expected m25p80
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.688000] m25p80 spi1.0: mx25l12805d (16384 Kbytes)
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.692000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1441N1
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.700000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.708000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11aaab
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.716000] bcm63xxpart: Partition 2 is rootfs offset 12abab and length ec5455
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.720000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.728000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.736000] 5 bcm63xxpart partitions found on MTD device spi1.0
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.744000] Creating 5 MTD partitions on "spi1.0":
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.748000] 0x000000000000-0x000000010000 : "CFE"
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.756000] 0x000000010100-0x00000012abab : "kernel"
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.760000] 0x00000012abab-0x000000ff0000 : "rootfs"
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.768000] mtd: device 2 (rootfs) set to be root filesystem
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.784000] 1 squashfs-split partitions found on MTD device rootfs
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.792000] 0x000000350000-0x000000ff0000 : "rootfs_data"
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.796000] 0x000000ff0000-0x000001000000 : "nvram"
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.804000] 0x000000010000-0x000000ff0000 : "linux"
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.848000] b53_common: found switch: BCM63xx, rev 0
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.852000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.860000] TCP: cubic registered
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.864000] NET: Registered protocol family 17
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.868000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    0.884000] Bridge firewalling registered
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.888000] 8021q: 802.1Q VLAN Support v1.8
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.904000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Tue Mar  1 09:16:57 2016 kern.info kernel: [    0.928000] Freeing unused kernel memory: 1304K (8035a000 - 804a0000)
Tue Mar  1 09:16:57 2016 user.info kernel: [    2.600000] init: Console is alive
Tue Mar  1 09:16:57 2016 user.info kernel: [    2.604000] init: - watchdog -
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    3.432000] random: nonblocking pool is initialized
Tue Mar  1 09:16:57 2016 user.info kernel: [    4.612000] init: - preinit -
Tue Mar  1 09:16:57 2016 kern.info kernel: [    5.524000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
Tue Mar  1 09:16:57 2016 kern.notice kernel: [    9.160000] jffs2: notice: (231) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Tue Mar  1 09:16:57 2016 user.info kernel: [    9.180000] mount_root: switching to jffs2 overlay
Tue Mar  1 09:16:57 2016 user.info kernel: [    9.252000] procd: - early -
Tue Mar  1 09:16:57 2016 user.info kernel: [    9.256000] procd: - watchdog -
Tue Mar  1 09:16:57 2016 user.info kernel: [   10.156000] procd: - ubus -
Tue Mar  1 09:16:57 2016 user.info kernel: [   11.164000] procd: - init -
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.904000] NET: Registered protocol family 10
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.920000] ip6_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.948000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.956000] Backport generated by backports.git backports-20150129-0-gdd4a670
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.968000] ip_tables: (C) 2000-2006 Netfilter Core Team
Tue Mar  1 09:16:57 2016 kern.info kernel: [   12.992000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.064000] xt_time: kernel timezone is -0000
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.112000] cfg80211: Calling CRDA to update world regulatory domain
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.152000] cfg80211: World regulatory domain updated:
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.156000] cfg80211:  DFS Master region: unset
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.172000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.180000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.188000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.196000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.204000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.216000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.224000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.232000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.360000] PPP generic driver version 2.4.2
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.372000] NET: Registered protocol family 24
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.428000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.436000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.440000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
Tue Mar  1 09:16:57 2016 kern.info kernel: [   13.448000] Broadcom 43xx driver loaded [ Features: PNL ]
Tue Mar  1 09:16:57 2016 kern.debug kernel: [   13.772000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Tue Mar  1 09:16:59 2016 kern.info kernel: [   19.128000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
Tue Mar  1 09:17:03 2016 authpriv.info dropbear[651]: Not backgrounding
Tue Mar  1 09:17:06 2016 daemon.info procd: - init complete -
Tue Mar  1 09:17:07 2016 kern.info kernel: [   26.660000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
Tue Mar  1 09:17:07 2016 kern.info kernel: [   26.672000] device eth0.1 entered promiscuous mode
Tue Mar  1 09:17:07 2016 kern.info kernel: [   26.680000] device eth0 entered promiscuous mode
Tue Mar  1 09:17:07 2016 kern.info kernel: [   26.692000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:17:07 2016 kern.info kernel: [   26.696000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'lan' is enabled
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'lan' is setting up now
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'lan' is now up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'loopback' is enabled
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'loopback' is setting up now
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'loopback' is now up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Network device 'eth0' link is up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Bridge 'br-lan' link is up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'lan' has link connectivity 
Tue Mar  1 09:17:07 2016 daemon.notice netifd: VLAN 'eth0.1' link is up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Network device 'lo' link is up
Tue Mar  1 09:17:07 2016 daemon.notice netifd: Interface 'loopback' has link connectivity 
Tue Mar  1 09:17:08 2016 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Tue Mar  1 09:17:08 2016 kern.info kernel: [   28.548000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
Tue Mar  1 09:17:09 2016 kern.info kernel: [   28.700000] br-lan: port 1(eth0.1) entered forwarding state
Tue Mar  1 09:17:09 2016 kern.info kernel: [   28.832000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Tue Mar  1 09:17:10 2016 daemon.notice netifd: radio0 (731): Successfully initialized wpa_supplicant
Tue Mar  1 09:17:11 2016 daemon.notice netifd: Interface 'wwan' is enabled
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.792000] wlan0: authenticate with 8c:0c:a3:23:5b:89
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.828000] wlan0: send auth to 8c:0c:a3:23:5b:89 (try 1/3)
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.836000] wlan0: authenticated
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.840000] b43 bcma0:1 wlan0: disabling HT as WMM/QoS is not supported by the AP
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.848000] b43 bcma0:1 wlan0: disabling VHT as WMM/QoS is not supported by the AP
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.860000] wlan0: associate with 8c:0c:a3:23:5b:89 (try 1/3)
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.868000] wlan0: RX AssocResp from 8c:0c:a3:23:5b:89 (capab=0x431 status=0 aid=2)
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.876000] wlan0: associated
Tue Mar  1 09:17:12 2016 kern.info kernel: [   31.880000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Mar  1 09:17:12 2016 daemon.notice netifd: Network device 'wlan0' link is up
Tue Mar  1 09:17:12 2016 daemon.notice netifd: Interface 'wwan' has link connectivity 
Tue Mar  1 09:17:12 2016 daemon.notice netifd: Interface 'wwan' is setting up now
Tue Mar  1 09:17:12 2016 daemon.notice netifd: wwan (867): udhcpc (v1.23.2) started
Tue Mar  1 09:17:12 2016 daemon.notice netifd: wwan (867): Sending discover...
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: started, version 2.73 cachesize 150
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC loop-detect inotify
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: DNS service limited to local subnets
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq-dhcp[884]: DHCP, IP range 192.168.3.100 -- 192.168.3.249, lease time 12h
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: using local addresses only for domain lan
Tue Mar  1 09:17:13 2016 daemon.warn dnsmasq[884]: no servers found in /tmp/resolv.conf.auto, will retry
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: read /etc/hosts - 1 addresses
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq[884]: read /tmp/hosts/dhcp - 1 addresses
Tue Mar  1 09:17:13 2016 daemon.info dnsmasq-dhcp[884]: read /etc/ethers - 0 addresses
Tue Mar  1 09:17:15 2016 daemon.notice netifd: wwan (867): Sending discover...
Tue Mar  1 09:17:15 2016 daemon.notice netifd: wwan (867): Sending select for 192.168.1.207...
Tue Mar  1 09:17:15 2016 daemon.notice netifd: wwan (867): Lease of 192.168.1.207 obtained, lease time 43200
Tue Mar  1 09:17:15 2016 daemon.notice netifd: Interface 'wwan' is now up
Tue Mar  1 09:17:15 2016 daemon.info dnsmasq[884]: reading /tmp/resolv.conf.auto
Tue Mar  1 09:17:15 2016 daemon.info dnsmasq[884]: using local addresses only for domain lan
Tue Mar  1 09:17:15 2016 daemon.info dnsmasq[884]: using nameserver 192.168.1.1#53
Tue Mar  1 09:17:16 2016 user.notice firewall: Reloading firewall due to ifup of wwan (wlan0)
Tue Mar  1 09:17:16 2016 daemon.warn odhcpd[615]: DHCPV6 SOLICIT IA_NA from 000100011d7757ac3863bbe386a7 on br-lan: ok fdb7:a9a6:83f0::bb6/128 
Tue Mar  1 09:17:17 2016 daemon.warn odhcpd[615]: DHCPV6 SOLICIT IA_NA from 000100011d7757ac3863bbe386a7 on br-lan: ok fdb7:a9a6:83f0::bb6/128 
Tue Mar  1 09:17:19 2016 daemon.warn odhcpd[615]: DHCPV6 SOLICIT IA_NA from 000100011d7757ac3863bbe386a7 on br-lan: ok fdb7:a9a6:83f0::bb6/128 
Tue Mar  1 09:17:23 2016 daemon.warn odhcpd[615]: DHCPV6 SOLICIT IA_NA from 000100011d7757ac3863bbe386a7 on br-lan: ok fdb7:a9a6:83f0::bb6/128 
Tue Mar  1 09:17:24 2016 daemon.warn odhcpd[615]: DHCPV6 REQUEST IA_NA from 000100011d7757ac3863bbe386a7 on br-lan: ok fdb7:a9a6:83f0::bb6/128 
Tue Mar  1 09:17:25 2016 daemon.info dnsmasq[884]: read /etc/hosts - 1 addresses
Tue Mar  1 09:17:25 2016 daemon.info dnsmasq[884]: read /tmp/hosts/odhcpd - 1 addresses
Tue Mar  1 09:17:25 2016 daemon.info dnsmasq[884]: read /tmp/hosts/dhcp - 1 addresses
Tue Mar  1 09:17:25 2016 daemon.info dnsmasq-dhcp[884]: read /etc/ethers - 0 addresses

And here is Kernel Log

[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r48532) ) #1 Tue Mar 1 10:07:16 CET 2016
[    0.000000] Detected Broadcom 0x6328 CPU revision b0
[    0.000000] CPU frequency is 320 MHz
[    0.000000] 64MB of RAM installed
[    0.000000] board_bcm963xx: Boot address 0xb8000000
[    0.000000] board_bcm963xx: CFE version: 1.0.37-106.24
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
[    0.000000] board: board name: 96328A-1441N1
[    0.000000] MIPS: machine is Comtrend AR-5387un
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 8033e370, node_mem_map 81002130
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 59972K/65536K available (2761K kernel code, 138K rwdata, 460K rodata, 1304K init, 192K bss, 5564K reserved)
[    0.000000] NR_IRQS:256
[    0.040000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
[    0.040000] pid_max: default: 32768 minimum: 301
[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.060000] NET: Registered protocol family 16
[    0.296000] registering PCI controller with io_map_base unset
[    0.316000] PCI host bridge to bus 0000:00
[    0.320000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
[    0.324000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.328000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.332000] pci 0000:00:00.0: [14e4:6328] type 01 class 0x060400
[    0.332000] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.332000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[    0.336000] pci 0000:01:00.0: [14e4:a8d8] type 00 class 0x028000
[    0.336000] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]
[    0.336000] pci 0000:01:00.0: supports D1 D2
[    0.336000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.336000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.336000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[    0.340000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[    0.344000] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.348000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
[    0.352000] Switched to clocksource MIPS
[    0.356000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    0.364000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    0.368000] bcma: bus0: Found chip with id 43225, rev 0x01 and package 0x0A
[    0.376000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
[    0.384000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
[    0.392000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
[    0.528000] bcma: bus0: Invalid SPROM read from the PCIe card, trying to use fallback SPROM
[    0.556000] bcma: bus0: Bus registered
[    0.560000] NET: Registered protocol family 2
[    0.568000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.576000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.580000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.588000] TCP: reno registered
[    0.592000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.596000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.604000] NET: Registered protocol family 1
[    0.608000] PCI: CLS 0 bytes, default 16
[    0.612000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.620000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.624000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.636000] msgmni has been set to 117
[    0.640000] io scheduler noop registered
[    0.644000] io scheduler deadline registered (default)
[    0.652000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
[    0.660000] console [ttyS0] enabled
[    0.668000] bootconsole [early0] disabled
[    0.680000] m25p80 spi1.0: found mx25l12805d, expected m25p80
[    0.688000] m25p80 spi1.0: mx25l12805d (16384 Kbytes)
[    0.692000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1441N1
[    0.700000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[    0.708000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 11aaab
[    0.716000] bcm63xxpart: Partition 2 is rootfs offset 12abab and length ec5455
[    0.720000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
[    0.728000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
[    0.736000] 5 bcm63xxpart partitions found on MTD device spi1.0
[    0.744000] Creating 5 MTD partitions on "spi1.0":
[    0.748000] 0x000000000000-0x000000010000 : "CFE"
[    0.756000] 0x000000010100-0x00000012abab : "kernel"
[    0.760000] 0x00000012abab-0x000000ff0000 : "rootfs"
[    0.768000] mtd: device 2 (rootfs) set to be root filesystem
[    0.784000] 1 squashfs-split partitions found on MTD device rootfs
[    0.792000] 0x000000350000-0x000000ff0000 : "rootfs_data"
[    0.796000] 0x000000ff0000-0x000001000000 : "nvram"
[    0.804000] 0x000000010000-0x000000ff0000 : "linux"
[    0.848000] b53_common: found switch: BCM63xx, rev 0
[    0.852000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
[    0.860000] TCP: cubic registered
[    0.864000] NET: Registered protocol family 17
[    0.868000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    0.884000] Bridge firewalling registered
[    0.888000] 8021q: 802.1Q VLAN Support v1.8
[    0.904000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    0.928000] Freeing unused kernel memory: 1304K (8035a000 - 804a0000)
[    2.600000] init: Console is alive
[    2.604000] init: - watchdog -
[    3.432000] random: nonblocking pool is initialized
[    4.612000] init: - preinit -
[    5.524000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[    9.160000] jffs2: notice: (231) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    9.180000] mount_root: switching to jffs2 overlay
[    9.252000] procd: - early -
[    9.256000] procd: - watchdog -
[   10.156000] procd: - ubus -
[   11.164000] procd: - init -
[   12.904000] NET: Registered protocol family 10
[   12.920000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.948000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[   12.956000] Backport generated by backports.git backports-20150129-0-gdd4a670
[   12.968000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.992000] nf_conntrack version 0.5.0 (957 buckets, 3828 max)
[   13.064000] xt_time: kernel timezone is -0000
[   13.112000] cfg80211: Calling CRDA to update world regulatory domain
[   13.152000] cfg80211: World regulatory domain updated:
[   13.156000] cfg80211:  DFS Master region: unset
[   13.160000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   13.172000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   13.180000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.188000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[   13.196000] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   13.204000] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   13.216000] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[   13.224000] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[   13.232000] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[   13.360000] PPP generic driver version 2.4.2
[   13.372000] NET: Registered protocol family 24
[   13.428000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
[   13.436000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
[   13.440000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2056, Revision 11, Version 0
[   13.448000] Broadcom 43xx driver loaded [ Features: PNL ]
[   13.772000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   19.128000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   26.660000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[   26.672000] device eth0.1 entered promiscuous mode
[   26.680000] device eth0 entered promiscuous mode
[   26.692000] br-lan: port 1(eth0.1) entered forwarding state
[   26.696000] br-lan: port 1(eth0.1) entered forwarding state
[   28.548000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[   28.700000] br-lan: port 1(eth0.1) entered forwarding state
[   28.832000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   31.792000] wlan0: authenticate with 8c:0c:a3:23:5b:89
[   31.828000] wlan0: send auth to 8c:0c:a3:23:5b:89 (try 1/3)
[   31.836000] wlan0: authenticated
[   31.840000] b43 bcma0:1 wlan0: disabling HT as WMM/QoS is not supported by the AP
[   31.848000] b43 bcma0:1 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[   31.860000] wlan0: associate with 8c:0c:a3:23:5b:89 (try 1/3)
[   31.868000] wlan0: RX AssocResp from 8c:0c:a3:23:5b:89 (capab=0x431 status=0 aid=2)
[   31.876000] wlan0: associated
[   31.880000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

Further testing will be posted. If you need Serial Log it can be done.

THANKS FOR EVERYTHING!

Re: NuCom R5010UN ADSL router

Im willing to try this bin in a Nucom R5000UNv2, same Broadcom 62328 as the R5010UN posted here. This is a widely distributed adsl router in latin america (telefonica, telecom, etc). I have been told that the D-Link 2750b rev T firmware works perfectly and this is the original firmware in case it helps m e d i a f i r e dot c o m/file/h0chcqqpgkwpkzu/R5000UNv2_R5TC008.7z

Any suggestions before trying the R5010UN bin file discussed here?

Re: NuCom R5010UN ADSL router

got it up and running using the dummy. How do I set up ATM-Bridge so it works just as a modem??? Wiki ain't helping.

Re: NuCom R5010UN ADSL router

Hi All,

How about getting the 4317 wireless chip to work in "n"  mode. Have used the NB604N/NB304N (also a 96328ang board) with "g" as a client. Really would like "n" mode as I have a number of these netcomm devices.

Mark

Re: NuCom R5010UN ADSL router

Hi everybody,

I have got a Nucom NU-GAN5 from Oceans Network. It's really a Netcomm NB-604N.

The bootlog is similar to the NuCom R5010N:

HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.37-106.5 for BCM96328 (32bit,SP,BE)
Build Date: 2013年 11月 08日 星期五 10:58:56 HKT (root@s54)
Copyright (C) 2000-2009 Broadcom Corporation.

clock=40000000
flash=MX25L64 size=8MB id=0xc22017  sector=64k

HS Serial flash device: name MX25L64, id 0xc22017 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000


Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-2)                    : 96328ang  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:07:26:8d:18:68  
PSI Size (1-64) KBytes            : 48  
Enable Backup PSI [0|1]           : 1  
System Log Size (0-256) KBytes    : 0  
Main Thread Number [0|1]          : 0  

send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (root@s54) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Fri Nov 8 10:44:22 HKT 2013
clock=40000000
flash=MX25L64 size=8MB id=0xc22017  sector=64k

HS Serial flash device: name MX25L64, id 0xc22017 size 8192KB
96328ang prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
 memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 80375680, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60080k/64512k available (2930k kernel code, 4412k reserved, 551k data, 132k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 1124 bytes
NET: Registered protocol family 16
Total Flash size: 8192K with 128 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0:   PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
bus: 'platform': really_probe: bound device bcmhs_spi.1 to driver bcmhs_spi
BLOG v3.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
bus: 'pci': really_probe: bound device 0000:01:00.0 to driver pcieport-driver
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
bus: 'usb': really_probe: bound device 1-0:1.0 to driver hub
bus: 'usb': really_probe: bound device usb1 to driver usb
bus: 'pci': really_probe: bound device 0000:00:0a.0 to driver ehci_hcd
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
bus: 'usb': really_probe: bound device 2-0:1.0 to driver hub
bus: 'usb': really_probe: bound device usb2 to driver usb
bus: 'pci': really_probe: bound device 0000:00:09.0 to driver ohci_hcd
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x800a is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Nov  8 2013 10:41:06
Broadcom Logger v0.1 Nov  8 2013 10:39:26
bus: 'spi': really_probe: bound device spi1.0 to driver bcm_HSSpiDev0
Mirror/redirect action on
u32 classifier
    input device check on 
    Actions configured 
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 132k freed
init started:  BusyBox v1.00 (2013.11.08-02:47+0000) multi-call binary
mount: Mounting devpts on /dev/pts failed: No such device


BusyBox v1.00 (2013.11.08-02:47+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules... 

pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 Nov 16 2010 15:04:32 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Nov 16 2010 15:04:32
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Nov  8 2013 10:39:33
ETH Init: 180 tx BDs at 0xa3941000
ETH Init: 400 rx BDs at 0xa3a08000
ETH Init: 400 rx BDs at 0xa3a0c000
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered 
eth0: MAC Address: 00:07:26:8D:18:68
eth1: MAC Address: 00:07:26:8D:18:68
eth2: MAC Address: 00:07:26:8D:18:68
eth3: MAC Address: 00:07:26:8D:18:68
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom strapped
wl:(srom strapped) probe/present=0
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43225_map.bin
wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.11.cpe4.406.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 
bus: 'pci': really_probe: bound device 0000:02:00.0 to driver wl
Broadcom 802.1Q VLAN Interface, v0.1

===== Release Version 4.06L.01 (build timestamp 130924_1857) =====

Fri Oct  1 00:00:00 UTC 2010
try read BPSI
try read MPSI
BPSI same to MPSI
MPSI valid, load into MDM
Adjust WLAN Configuration, has configuration [1], num [4], defaultnum [4]
Success 
syntax error
ip_tables: (C) 2000-2006 Netfilter Core Team
ip6_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
Switching back to primary dns server (0.0.0.0).
device eth0 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
device eth1 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth1: link is not ready
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
device eth2 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth2: link is not ready
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
device eth3 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth3: link is not ready
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
BcmAdsl_Initialize=0xC00DD188, g_pFnNotifyCallback=0xC0106B24
pSdramPHY=0xA3FFFFF8, 0x8033F71 0x5EADBEEF
*** XfaceOffset: 0x21F90 => 0x21F90 ***
WLmngr Daemon is running
optarg=0 shmId=0 
*** PhySdramSize got adjusted: 0x8339C => 0x98D48 ***
AdslCoreSharedMemInit: shareMemAvailable=422544
AdslCoreHwReset:  pLocSbSta=83288000 bkupThreshold=1600
AdslCoreHwReset:  AdslOemDataAddr = 0xA3F783D4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 
XTM Init: 400 rx BDs at 0xa335f000
XTM Init: 100 rx BDs at 0xa3208800
/var/3gppp/bootupdalay: cannot create
###reset_nf_conntrack_net_ops;543;###
###reset_nf_conntrack_net_ops;543;###
insmod: cannot insert `/lib/modules/2.6.30/extra/pktflow.ko': Success (17): Success
killall: smbd: no process killed
monitor task is initialized pid= 264 
br0: port 1(eth0) entering disabled state
br0: port 2(eth1) entering disabled state
br0: port 3(eth2) entering disabled state
br0: port 4(eth3) entering disabled state
can not open /var/msghpsskStart to start 3g-mngr diald task!!!!
WEBUI Operation WPS Type is NONE, interface number is [1]
WEBUI Operation WPS Type is NONE, interface number is [2]
WEBUI Operation WPS Type is NONE, interface number is [3]
WEBUI Operation WPS Type is NONE, interface number is [4]
There is no Predefined DevicePin in CFE
WPS Device PIN = 18518313
can not open /var/msghpsskModem Monitor Socket Receve Msg:[getconns]
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
Setting SSID: "VIVA_ZAPATA"
Setting SSID: "Broadcom2"
wl0.1 (): not using net_device_ops yet
Setting SSID: "Brwl0.2 (): not using net_device_ops yet
oadcom3"
Setting SSID: "Brwl0.3 (): not using net_device_ops yet
oadcom4"
wlctl: Unsupported
wlctl: Not Permitted
wlctl: Unsupported
Modem Monitor Socket Receve Msg:[getconns]
Modem Monitor Socket Receve Msg:[getconns]
USB Serial support registered for 3G_USB_modem
usbcore: registered new interface driver 3g_modem
[USB MODEM SERIAL modem_usb_id_proc_write:211] Do attach...
chanspec 0x2b01 selected 
device wl0 entered promiscuous mode
device wl0.1 entered promiscuous mode
device wl0.2 entered promiscuous mode
device wl0.3 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Reaped 2138
UPnP daemon is ready to run

BCM96328 Broadband Router
Login: 
Password:

I think I can load the OpenWrt or LEDE firmware for R5010UN. I load the dummy CFE whitout any problem, but when I try to load the Openwrt/LEDE the process fails. Looking at CFE I see this error:

           Illegal image size 8388608.  Image size must not be greater than 8216320.

The flash disk of NB604N/NU-GAN5 is 8MB, and the flash of R5010N is 16MB. The squashfs image that I downloaded does not fit in my router.

Is it possible build a smaller image?.

Thanks!!!