I was unable to find a way to attach files (as an administrator, you can install a plugin for that), but the following should also work:
[ 0.000000] Linux version 3.10.44 (a@b) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41510) ) #4 Sun Jul 6 13:54:10 CEST 2014
[ 0.000000] MyLoader: sysp=aaaa5554, boardp=aaaa5554, parts=aaaa5554
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 8030e9b0, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32768 pages, LIFO batch:7
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=WNDR3700 console=ttyS0,115200 mtdparts=spi0.0:320k(u-boot)ro,128k(u-boot-env)ro,15872k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126248k/131072k available (2236k kernel code, 4824k reserved, 597k data, 236k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.060000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is NETGEAR WNDR3700/WNDR3800/WNDRMAC
[ 2.680000] registering PCI controller with io_map_base unset
[ 2.690000] bio: create slab <bio-0> at 0
[ 2.690000] PCI host bridge to bus 0000:00
[ 2.700000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff]
[ 2.700000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 2.710000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 2.710000] pci 0000:00:11.0: [168c:ff1d] type 00 class 0x020000
[ 2.710000] pci 0000:00:11.0: fixup device configuration
[ 2.720000] pci 0000:00:11.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 2.720000] pci 0000:00:11.0: PME# supported from D0 D3hot
[ 2.720000] pci 0000:00:12.0: [168c:ff1d] type 00 class 0x020000
[ 2.720000] pci 0000:00:12.0: fixup device configuration
[ 2.720000] pci 0000:00:12.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 2.720000] pci 0000:00:12.0: PME# supported from D0 D3hot
[ 2.720000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[ 2.720000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 2.730000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[ 2.730000] pci 0000:00:11.0: using irq 40 for pin 1
[ 2.740000] pci 0000:00:12.0: using irq 41 for pin 1
[ 2.740000] Switching to clocksource MIPS
[ 2.750000] NET: Registered protocol family 2
[ 2.750000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 2.750000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.760000] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.760000] TCP: reno registered
[ 2.770000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.770000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.780000] NET: Registered protocol family 1
[ 2.780000] PCI: CLS 0 bytes, default 32
[ 2.790000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.800000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 2.810000] msgmni has been set to 246
[ 2.810000] io scheduler noop registered
[ 2.820000] io scheduler deadline registered (default)
[ 2.820000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.850000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 2.860000] console [ttyS0] enabled, bootconsole disabled
[ 2.870000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 2.880000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 2.880000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 2.890000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 2.890000] Creating 4 MTD partitions on "spi0.0":
[ 2.900000] 0x000000000000-0x000000050000 : "u-boot"
[ 2.900000] 0x000000050000-0x000000070000 : "u-boot-env"
[ 2.910000] 0x000000070000-0x000000ff0000 : "firmware"
[ 2.920000] 2 netgear-fw partitions found on MTD device firmware
[ 2.920000] 0x000000070000-0x000000170440 : "kernel"
[ 2.930000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.940000] 0x000000170440-0x000000ff0000 : "rootfs"
[ 2.950000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 2.960000] mtd: device 4 (rootfs) set to be root filesystem
[ 2.970000] 1 squashfs-split partitions found on MTD device rootfs
[ 2.970000] 0x0000005e0000-0x000000ff0000 : "rootfs_data"
[ 2.980000] 0x000000ff0000-0x000001000000 : "art"
[ 2.990000] Realtek RTL8366S ethernet switch driver version 0.2.2
[ 2.990000] rtl8366s rtl8366s: using GPIO pins 5 (SDA) and 7 (SCK)
[ 3.000000] rtl8366s rtl8366s: RTL8366 ver. 1 chip found
[ 3.040000] libphy: rtl8366s: probed
[ 3.350000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:RGMII
[ 3.650000] ag71xx ag71xx.1: connected to PHY at rtl8366s:04 [uid=001cc960, driver=Generic PHY]
[ 3.660000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:RGMII
[ 3.670000] TCP: cubic registered
[ 3.670000] NET: Registered protocol family 17
[ 3.680000] 8021q: 802.1Q VLAN Support v1.8
[ 3.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 3.700000] Freeing unused kernel memory: 236K (80325000 - 80360000)
[ 5.890000] usbcore: registered new interface driver usbfs
[ 5.890000] usbcore: registered new interface driver hub
[ 5.900000] usbcore: registered new device driver usb
[ 5.930000] SCSI subsystem initialized
[ 5.940000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.950000] ehci-platform: EHCI generic platform driver
[ 5.950000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.960000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.970000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.990000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.990000] hub 1-0:1.0: USB hub found
[ 6.000000] hub 1-0:1.0: 2 ports detected
[ 6.000000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.010000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 6.010000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 6.020000] ohci-platform ohci-platform: irq 14, io mem 0x1c000000
[ 6.090000] hub 2-0:1.0: USB hub found
[ 6.090000] hub 2-0:1.0: 2 ports detected
[ 6.100000] usbcore: registered new interface driver usb-storage
[ 6.320000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.580000] hub 1-1:1.0: USB hub found
[ 6.580000] hub 1-1:1.0: 4 ports detected
[ 6.700000] ar71xx: pll_reg 0xb8050010: 0x11110000
[ 6.700000] eth0: link up (1000Mbps/Full duplex)
[ 6.880000] usb 1-1.1: new high-speed USB device number 3 using ehci-platform
[ 6.990000] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 6.990000] scsi0 : usb-storage 1-1.1:1.0
[ 7.080000] usb 1-1.2: new high-speed USB device number 4 using ehci-platform
[ 7.190000] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[ 7.190000] scsi1 : usb-storage 1-1.2:1.0
[ 7.280000] usb 1-1.4: new high-speed USB device number 5 using ehci-platform
[ 7.390000] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 7.390000] scsi2 : usb-storage 1-1.4:1.0
[ 10.180000] jffs2: notice: (373) jffs2_build_xattr_subsystem: complete building xattr subsystem, 33 of xdatum (1 unchecked, 32 orphan) and 56 of xref (0 dead, 41 orphan) found.
[ 10.230000] scsi 1:0:0:0: Direct-Access Hitachi HDT721010SLA360 PQ: 0 ANSI: 2 CCS
[ 10.440000] scsi 2:0:0:0: Direct-Access Hitachi HDT721010SLA360 PQ: 0 ANSI: 2 CCS
[ 18.270000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 18.280000] sd 1:0:0:0: [sda] Write Protect is off
[ 18.290000] sd 1:0:0:0: [sda] Mode Sense: 34 00 00 00
[ 18.290000] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 18.350000] sda: sda1
[ 18.350000] sd 1:0:0:0: [sda] Attached SCSI disk
[ 18.480000] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 18.490000] sd 2:0:0:0: [sdb] Write Protect is off
[ 18.490000] sd 2:0:0:0: [sdb] Mode Sense: 34 00 00 00
[ 18.490000] sd 2:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 18.550000] sdb: sdb1
[ 18.560000] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 19.350000] scsi 0:0:0:0: Direct-Access Hitachi HDS723030ALA640 PQ: 0 ANSI: 5
[ 19.360000] sd 0:0:0:0: [sdc] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB)
[ 19.370000] sd 0:0:0:0: [sdc] Write Protect is off
[ 19.370000] sd 0:0:0:0: [sdc] Mode Sense: 28 00 00 00
[ 19.370000] sd 0:0:0:0: [sdc] No Caching mode page found
[ 19.380000] sd 0:0:0:0: [sdc] Assuming drive cache: write through
[ 19.390000] sd 0:0:0:0: [sdc] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB)
[ 19.400000] sd 0:0:0:0: [sdc] No Caching mode page found
[ 19.400000] sd 0:0:0:0: [sdc] Assuming drive cache: write through
[ 19.450000] sdc: sdc1
[ 19.460000] sd 0:0:0:0: [sdc] 732566645 4096-byte logical blocks: (3.00 TB/2.72 TiB)
[ 19.470000] sd 0:0:0:0: [sdc] No Caching mode page found
[ 19.470000] sd 0:0:0:0: [sdc] Assuming drive cache: write through
[ 19.480000] sd 0:0:0:0: [sdc] Attached SCSI disk
[ 25.510000] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
[ 25.650000] jffs2: notice: (370) jffs2_build_xattr_subsystem: complete building xattr subsystem, 33 of xdatum (1 unchecked, 32 orphan) and 56 of xref (0 dead, 41 orphan) found.
[ 25.680000] eth0: link down
[ 26.310000] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts:
[ 26.560000] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts:
[ 27.450000] NET: Registered protocol family 10
[ 27.460000] nf_conntrack version 0.5.0 (1976 buckets, 7904 max)
[ 27.470000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 27.480000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 27.490000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 27.500000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 27.540000] xt_time: kernel timezone is -0000
[ 27.560000] cfg80211: Calling CRDA to update world regulatory domain
[ 27.570000] cfg80211: World regulatory domain updated:
[ 27.580000] cfg80211: DFS Master region: unset
[ 27.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 27.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 27.600000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 27.610000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 27.620000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
[ 27.630000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 27.630000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 27.640000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 27.650000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 27.690000] PPP generic driver version 2.4.2
[ 27.700000] NET: Registered protocol family 24
[ 27.730000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[ 27.740000] ath: EEPROM regdomain: 0x0
[ 27.740000] ath: EEPROM indicates default country code should be used
[ 27.740000] ath: doing EEPROM country->regdmn map search
[ 27.740000] ath: country maps to regdmn code: 0x3a
[ 27.740000] ath: Country alpha2 being used: US
[ 27.740000] ath: Regpair used: 0x3a
[ 27.760000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 27.770000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
[ 27.790000] cfg80211: Calling CRDA for country: US
[ 27.790000] cfg80211: Regulatory domain changed to country: US
[ 27.800000] cfg80211: DFS Master region: FCC
[ 27.800000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 27.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
[ 27.820000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
[ 27.830000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
[ 27.830000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
[ 27.840000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 27.850000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[ 27.860000] ath: phy1: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 27.870000] ath: phy1: random mac address will be used: 42:e0:cd:4c:81:85
[ 27.880000] ath: EEPROM regdomain: 0x0
[ 27.880000] ath: EEPROM indicates default country code should be used
[ 27.880000] ath: doing EEPROM country->regdmn map search
[ 27.880000] ath: country maps to regdmn code: 0x3a
[ 27.880000] ath: Country alpha2 being used: US
[ 27.880000] ath: Regpair used: 0x3a
[ 27.910000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 27.910000] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=41
[ 33.570000] ar71xx: pll_reg 0xb8050010: 0x11110000
[ 33.570000] eth0: link up (1000Mbps/Full duplex)
[ 33.580000] device eth0.1 entered promiscuous mode
[ 33.580000] device eth0 entered promiscuous mode
[ 33.590000] br-lan: port 1(eth0.1) entered forwarding state
[ 33.600000] br-lan: port 1(eth0.1) entered forwarding state
[ 33.610000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 34.750000] cfg80211: Calling CRDA for country: NL
[ 34.770000] cfg80211: Regulatory domain changed to country: NL
[ 34.780000] cfg80211: DFS Master region: ETSI
[ 34.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 34.790000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 34.810000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm), (0 s)
[ 34.820000] cfg80211: (5490000 KHz - 5710000 KHz @ 80000 KHz), (N/A, 2700 mBm), (0 s)
[ 34.830000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
[ 35.600000] br-lan: port 1(eth0.1) entered forwarding state
[ 35.920000] ar71xx: pll_reg 0xb8050014: 0x11110000
[ 35.920000] eth1: link up (1000Mbps/Full duplex)
[ 36.310000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 36.400000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 36.490000] device wlan1 entered promiscuous mode
[ 36.490000] br-lan: port 2(wlan1) entered forwarding state
[ 36.500000] br-lan: port 2(wlan1) entered forwarding state
[ 36.760000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.790000] device wlan0 entered promiscuous mode
[ 36.790000] br-lan: port 3(wlan0) entered forwarding state
[ 36.800000] br-lan: port 3(wlan0) entered forwarding state
[ 37.310000] br-lan: port 2(wlan1) entered disabled state
[ 37.310000] br-lan: port 3(wlan0) entered disabled state
[ 41.250000] device wlan1 left promiscuous mode
[ 41.260000] br-lan: port 2(wlan1) entered disabled state
[ 41.750000] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 44.960000] br-lan: port 3(wlan0) entered forwarding state
[ 44.970000] br-lan: port 3(wlan0) entered forwarding state
[ 44.980000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 46.970000] br-lan: port 3(wlan0) entered forwarding state
[ 179.520000] EXT4-fs (sdc1): couldn't mount as ext3 due to feature incompatibilities
[ 179.530000] EXT4-fs (sdc1): couldn't mount as ext2 due to feature incompatibilities
[ 179.770000] EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: (null)
[ 4189.930000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.