OpenWrt Forum Archive

Topic: [TL-WDR4300] 5Ghz wifi (radio1) at 0%

The content of this topic has been archived on 21 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Post #1
Ferguson
2 Jul 2014, 11:10

Hi everybody,

I have bought a TP-Link WDR4300 v1.7 and put openwrt in it thanks to the wiki :
http://wiki.openwrt.org/toh/tp-link/tl-wdr4300

I have installed Attitude Adjustment 12.09 (image : openwrt-ar71xx-generic-tl-wdr4300-v1-squashfs-factory.bin) and everything works fine (I have LuCI and internet working with eth and Wlan).

This router can provide 2 wireless networks :

MAC80211 802.11bgn (radio0)
MAC80211 802.11an (radio1)

The radio0 is working fine but the radio1 is stuck to 0%.

Here a copy of my config file :

 cat /etc/config/wireless 

config wifi-device 'radio0'
    option type 'mac80211'
    option channel '11'
    option macaddr 'c0:4a:00:e4:86:23'
    option hwmode '11ng'
    option htmode 'HT20'
    list ht_capab 'LDPC'
    list ht_capab 'SHORT-GI-20'
    list ht_capab 'SHORT-GI-40'
    list ht_capab 'TX-STBC'
    list ht_capab 'RX-STBC1'
    list ht_capab 'DSSS_CCK-40'
    option country 'FR'
    option txpower '20'
    option distance '50'

config wifi-iface
    option device 'radio0'
    option network 'lan'
    option mode 'ap'
    option encryption 'psk2+tkip+ccmp'
    option ssid 'XXX'
    option key 'XXX'

config wifi-device 'radio1'
    option type 'mac80211'
    option macaddr 'c0:4a:00:e4:86:24'
    option hwmode '11na'
    option htmode 'HT20'
    list ht_capab 'LDPC'
    list ht_capab 'SHORT-GI-20'
    list ht_capab 'SHORT-GI-40'
    list ht_capab 'TX-STBC'
    list ht_capab 'RX-STBC1'
    list ht_capab 'DSSS_CCK-40'
    option txpower '17'
    option country 'FR'
    option distance '50'
    option channel 'auto'

config wifi-iface
    option device 'radio1'
    option network 'lan'
    option mode 'ap'
    option ssid 'XXX'
    option encryption 'psk2+tkip+ccmp'
    option key 'XXX'

I have replaced SSID and keys on purpose. The radio0 is working but the radio1 is stuck at 0% and doesn't work.
I would be most grateful if you could help me. I read the forum + wiki but never saw any good answer. I would like to make both wi-fi run at the same time.

Thank you

(Last edited by Ferguson on 2 Jul 2014, 13:42)

Post #2
jow
2 Jul 2014, 11:21

0% is normal if no client is associated because then there is no signal to measure.

Post #3
Ferguson
2 Jul 2014, 12:21
jow wrote:

0% is normal if no client is associated because then there is no signal to measure.

I'm running Ubuntu 14.04, and when i'm trying to find the ESSID of the Wifi signal, I can only find the radio0 one.

I can't find the radio1 one with NetworkManager.

I tried also with my android phone and i can't find the ESSID as well.

I didn't tick the 'hide ESSID' option in LuCI.

Thank you for your help.

Post #4
nebbia88
2 Jul 2014, 12:29

are you sure your clients have a dual band wifi card?

Post #5
qasdfdsaq
2 Jul 2014, 12:36

What channel does it claim to be on? Most likely DFS isn't working properly (it rarely does) so you need to set the channel manually to a non DFS one. Even if DFS did work it'd take a minute or two to come up, are you waiting long enough?


Post your system log.

(Last edited by qasdfdsaq on 2 Jul 2014, 12:37)

Post #6
Ferguson
2 Jul 2014, 12:53
nebbia88 wrote:

are you sure your clients have a dual band wifi card?

Dual Band Wifi Card = Wifi N acceptance so yes every clients I use have it.

qasdfdsaq wrote:

What channel does it claim to be on? Most likely DFS isn't working properly (it rarely does) so you need to set the channel manually to a non DFS one. Even if DFS did work it'd take a minute or two to come up, are you waiting long enough?


Post your system log.

I tried to reboot wi-fi with this :
http://wiki.openwrt.org/doc/faq/faq.wir … s.dfs.mean

It doesn't come up. I have choosen channel 36 for 5GhZ. I waited for like 30min. I didn't come up.

As for the system logs :

Jul  2 09:44:34 OpenWrt kern.info kernel: [ 1129.100000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:44:34 OpenWrt kern.info kernel: [ 1129.100000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:44:35 OpenWrt user.notice ifup: Allowing Router Advertisements on wan (br-wan)
Jul  2 09:44:35 OpenWrt user.info firewall: adding wan (br-wan) to zone wan
Jul  2 09:44:36 OpenWrt kern.info kernel: [ 1131.100000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:44:37 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 09:44:37 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 09:44:37 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 09:44:39 OpenWrt kern.info kernel: [ 1133.240000] device wlan1 entered promiscuous mode
Jul  2 09:44:39 OpenWrt kern.info kernel: [ 1133.480000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:44:39 OpenWrt kern.info kernel: [ 1133.490000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:44:41 OpenWrt kern.info kernel: [ 1135.490000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:44:42 OpenWrt daemon.info dnsmasq[23970]: reading /tmp/resolv.conf.auto
Jul  2 09:44:42 OpenWrt daemon.info dnsmasq[23970]: using nameserver 212.27.40.240#53
Jul  2 09:44:42 OpenWrt daemon.info dnsmasq[23970]: using nameserver 212.27.40.241#53
Jul  2 09:44:42 OpenWrt daemon.info dnsmasq[23970]: using local addresses only for domain lan
Jul  2 09:44:42 OpenWrt daemon.info dnsmasq[23970]: exiting on receipt of SIGTERM
Jul  2 09:44:42 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul  2 09:44:42 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: started, version 2.62 cachesize 150
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq-dhcp[7426]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: using local addresses only for domain lan
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: reading /tmp/resolv.conf.auto
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: using nameserver 212.27.40.240#53
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: using nameserver 212.27.40.241#53
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: using local addresses only for domain lan
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq[7426]: read /etc/hosts - 1 addresses
Jul  2 09:44:45 OpenWrt daemon.info dnsmasq-dhcp[7426]: read /etc/ethers - 0 addresses
Jul  2 09:44:50 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Jul  2 09:44:51 OpenWrt user.info firewall: adding wan (br-wan) to zone wan
Jul  2 09:48:45 OpenWrt kern.info kernel: [ 1380.060000] device wlan0 left promiscuous mode
Jul  2 09:48:45 OpenWrt kern.info kernel: [ 1380.060000] br-lan: port 2(wlan0) entered disabled state
Jul  2 09:48:46 OpenWrt kern.info kernel: [ 1380.250000] device wlan1 left promiscuous mode
Jul  2 09:48:46 OpenWrt kern.info kernel: [ 1380.250000] br-lan: port 3(wlan1) entered disabled state
Jul  2 09:48:47 OpenWrt kern.info kernel: [ 1381.410000] device wlan0 entered promiscuous mode
Jul  2 09:48:47 OpenWrt kern.info kernel: [ 1381.660000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:48:47 OpenWrt kern.info kernel: [ 1381.670000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:48:49 OpenWrt kern.info kernel: [ 1383.670000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:48:50 OpenWrt kern.info kernel: [ 1385.000000] device wlan1 entered promiscuous mode
Jul  2 09:48:51 OpenWrt kern.info kernel: [ 1385.250000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:48:51 OpenWrt kern.info kernel: [ 1385.260000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:48:52 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 09:48:52 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 09:48:52 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 09:48:53 OpenWrt kern.info kernel: [ 1387.260000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:07 OpenWrt kern.info kernel: [ 1401.410000] device wlan0 left promiscuous mode
Jul  2 09:49:07 OpenWrt kern.info kernel: [ 1401.410000] br-lan: port 2(wlan0) entered disabled state
Jul  2 09:49:07 OpenWrt kern.info kernel: [ 1401.680000] device wlan1 left promiscuous mode
Jul  2 09:49:07 OpenWrt kern.info kernel: [ 1401.680000] br-lan: port 3(wlan1) entered disabled state
Jul  2 09:49:09 OpenWrt kern.info kernel: [ 1403.200000] device wlan0 entered promiscuous mode
Jul  2 09:49:09 OpenWrt kern.info kernel: [ 1403.460000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:09 OpenWrt kern.info kernel: [ 1403.460000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:11 OpenWrt kern.info kernel: [ 1405.460000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:12 OpenWrt kern.info kernel: [ 1406.780000] device wlan1 entered promiscuous mode
Jul  2 09:49:12 OpenWrt kern.info kernel: [ 1407.030000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:12 OpenWrt kern.info kernel: [ 1407.030000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:14 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 09:49:14 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 09:49:14 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 09:49:14 OpenWrt kern.info kernel: [ 1409.030000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:15 OpenWrt daemon.info dnsmasq[7426]: reading /tmp/resolv.conf.auto
Jul  2 09:49:15 OpenWrt daemon.info dnsmasq[7426]: using nameserver 212.27.40.240#53
Jul  2 09:49:15 OpenWrt daemon.info dnsmasq[7426]: using nameserver 212.27.40.241#53
Jul  2 09:49:15 OpenWrt daemon.info dnsmasq[7426]: using local addresses only for domain lan
Jul  2 09:49:15 OpenWrt daemon.info dnsmasq[7426]: exiting on receipt of SIGTERM
Jul  2 09:49:16 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul  2 09:49:16 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: started, version 2.62 cachesize 150
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq-dhcp[18743]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: using local addresses only for domain lan
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: reading /tmp/resolv.conf.auto
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: using nameserver 212.27.40.240#53
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: using nameserver 212.27.40.241#53
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: using local addresses only for domain lan
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq[18743]: read /etc/hosts - 1 addresses
Jul  2 09:49:19 OpenWrt daemon.info dnsmasq-dhcp[18743]: read /etc/ethers - 0 addresses
Jul  2 09:49:24 OpenWrt user.info firewall: adding lan (br-lan) to zone lan
Jul  2 09:49:24 OpenWrt user.info firewall: adding wan (br-wan) to zone wan
Jul  2 09:49:33 OpenWrt kern.info kernel: [ 1427.370000] device wlan0 left promiscuous mode
Jul  2 09:49:33 OpenWrt kern.info kernel: [ 1427.370000] br-lan: port 2(wlan0) entered disabled state
Jul  2 09:49:33 OpenWrt kern.info kernel: [ 1427.550000] device wlan1 left promiscuous mode
Jul  2 09:49:33 OpenWrt kern.info kernel: [ 1427.550000] br-lan: port 3(wlan1) entered disabled state
Jul  2 09:49:34 OpenWrt kern.info kernel: [ 1428.730000] device wlan0 entered promiscuous mode
Jul  2 09:49:34 OpenWrt kern.info kernel: [ 1428.990000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:34 OpenWrt kern.info kernel: [ 1428.990000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:36 OpenWrt kern.info kernel: [ 1430.990000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1432.880000] device wlan1 entered promiscuous mode
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1433.120000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1433.130000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1433.150000] device wlan1-1 entered promiscuous mode
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1433.160000] br-lan: port 4(wlan1-1) entered forwarding state
Jul  2 09:49:38 OpenWrt kern.info kernel: [ 1433.160000] br-lan: port 4(wlan1-1) entered forwarding state
Jul  2 09:49:40 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 09:49:40 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 09:49:40 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 09:49:40 OpenWrt kern.info kernel: [ 1435.130000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 09:49:40 OpenWrt kern.info kernel: [ 1435.160000] br-lan: port 4(wlan1-1) entered forwarding state
Jul  2 09:59:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:09:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:19:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:29:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:39:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:49:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 10:59:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 11:09:34 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 11:15:20 OpenWrt kern.info kernel: [ 6575.160000] device wlan0 left promiscuous mode
Jul  2 11:15:20 OpenWrt kern.info kernel: [ 6575.160000] br-lan: port 2(wlan0) entered disabled state
Jul  2 11:15:21 OpenWrt kern.info kernel: [ 6575.360000] br-lan: port 4(wlan1-1) entered disabled state
Jul  2 11:15:21 OpenWrt kern.info kernel: [ 6575.360000] device wlan1-1 left promiscuous mode
Jul  2 11:15:21 OpenWrt kern.info kernel: [ 6575.370000] br-lan: port 4(wlan1-1) entered disabled state
Jul  2 11:15:21 OpenWrt kern.info kernel: [ 6575.380000] device wlan1 left promiscuous mode
Jul  2 11:15:21 OpenWrt kern.info kernel: [ 6575.380000] br-lan: port 3(wlan1) entered disabled state
Jul  2 11:15:22 OpenWrt kern.info kernel: [ 6576.600000] device wlan0 entered promiscuous mode
Jul  2 11:15:22 OpenWrt kern.info kernel: [ 6576.850000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:15:22 OpenWrt kern.info kernel: [ 6576.860000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:15:24 OpenWrt kern.info kernel: [ 6578.860000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:15:26 OpenWrt kern.info kernel: [ 6580.150000] device wlan1 entered promiscuous mode
Jul  2 11:15:26 OpenWrt kern.info kernel: [ 6580.400000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:15:26 OpenWrt kern.info kernel: [ 6580.400000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:15:27 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 11:15:27 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 11:15:27 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 11:15:28 OpenWrt kern.info kernel: [ 6582.400000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.350000] br-lan: port 2(wlan0) entered disabled state
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.510000] device wlan0 left promiscuous mode
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.510000] br-lan: port 2(wlan0) entered disabled state
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.700000] br-lan: port 3(wlan1) entered disabled state
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.770000] device wlan1 left promiscuous mode
Jul  2 11:19:01 OpenWrt kern.info kernel: [ 6795.770000] br-lan: port 3(wlan1) entered disabled state
Jul  2 11:19:02 OpenWrt kern.info kernel: [ 6796.960000] device wlan0 entered promiscuous mode
Jul  2 11:19:03 OpenWrt kern.info kernel: [ 6797.210000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:19:03 OpenWrt kern.info kernel: [ 6797.220000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:19:05 OpenWrt kern.info kernel: [ 6799.220000] br-lan: port 2(wlan0) entered forwarding state
Jul  2 11:19:06 OpenWrt kern.info kernel: [ 6800.530000] device wlan1 entered promiscuous mode
Jul  2 11:19:06 OpenWrt kern.info kernel: [ 6800.780000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:19:06 OpenWrt kern.info kernel: [ 6800.780000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:19:08 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: authenticated
Jul  2 11:19:08 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed IEEE 802.11: associated (aid 1)
Jul  2 11:19:08 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: pairwise key handshake completed (RSN)
Jul  2 11:19:08 OpenWrt kern.info kernel: [ 6802.780000] br-lan: port 3(wlan1) entered forwarding state
Jul  2 11:19:09 OpenWrt daemon.info dnsmasq[18743]: reading /tmp/resolv.conf.auto
Jul  2 11:19:09 OpenWrt daemon.info dnsmasq[18743]: using nameserver 212.27.40.240#53
Jul  2 11:19:09 OpenWrt daemon.info dnsmasq[18743]: using nameserver 212.27.40.241#53
Jul  2 11:19:09 OpenWrt daemon.info dnsmasq[18743]: using local addresses only for domain lan
Jul  2 11:19:09 OpenWrt daemon.info dnsmasq[18743]: exiting on receipt of SIGTERM
Jul  2 11:19:10 OpenWrt user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Jul  2 11:19:10 OpenWrt user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: started, version 2.62 cachesize 150
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq-dhcp[24224]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: using local addresses only for domain lan
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: reading /tmp/resolv.conf.auto
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: using nameserver 212.27.40.240#53
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: using nameserver 212.27.40.241#53
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: using local addresses only for domain lan
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq[24224]: read /etc/hosts - 1 addresses
Jul  2 11:19:13 OpenWrt daemon.info dnsmasq-dhcp[24224]: read /etc/ethers - 0 addresses
Jul  2 11:29:03 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 11:39:03 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)
Jul  2 11:49:03 OpenWrt daemon.info hostapd: wlan0: STA 68:5d:43:08:c8:ed WPA: group key handshake completed (RSN)

As for the kernel logs : 

[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 16:49:30 UTC 2013
[    0.000000] MyLoader: sysp=84c31530, boardp=0065cbe4, parts=195ef6a4
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[    0.000000] SoC: Atheros AR9344 rev 2
[    0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00008000
[    0.000000] Movable zone start PFN for each node
[    0.000000] Early memory PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00008000
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat 802f1100, node_mem_map 81000000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32512 pages, LIFO batch:7
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line:  board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 126464k/131072k available (2211k kernel code, 4608k reserved, 418k data, 212k init, 0k highmem)
[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[    0.070000] pid_max: default: 32768 minimum: 301
[    0.070000] Mount-cache hash table entries: 512
[    0.080000] NET: Registered protocol family 16
[    0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[    0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[    0.090000] registering PCI controller with io_map_base unset
[    0.310000] bio: create slab <bio-0> at 0
[    0.310000] PCI host bridge to bus 0000:00
[    0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    0.320000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.330000] pci 0000:00:00.0: [168c:0033] type 0 class 0x000280
[    0.330000] pci 0000:00:00.0: invalid calibration data
[    0.330000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
[    0.330000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[    0.330000] pci 0000:00:00.0: supports D1
[    0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[    0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.340000] pci 0000:00:00.0: using irq 40 for pin 1
[    0.350000] Switching to clocksource MIPS
[    0.350000] NET: Registered protocol family 2
[    0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    0.370000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.380000] TCP reno registered
[    0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.390000] NET: Registered protocol family 1
[    0.400000] PCI: CLS 0 bytes, default 32
[    0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.430000] msgmni has been set to 247
[    0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[    0.440000] io scheduler noop registered
[    0.440000] io scheduler deadline registered (default)
[    0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[    0.490000] console [ttyS0] enabled, bootconsole disabled
[    0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
[    0.510000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[    0.510000] 5 tp-link partitions found on MTD device spi0.0
[    0.520000] Creating 5 MTD partitions on "spi0.0":
[    0.520000] 0x000000000000-0x000000020000 : "u-boot"
[    0.530000] 0x000000020000-0x000000109d54 : "kernel"
[    0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.550000] 0x000000109d54-0x0000007f0000 : "rootfs"
[    0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.570000] mtd: partition "rootfs" set to be root filesystem
[    0.570000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=510000 
[    0.580000] 0x0000002e0000-0x0000007f0000 : "rootfs_data"
[    0.590000] 0x0000007f0000-0x000000800000 : "art"
[    0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[    0.730000] ag71xx_mdio: probed
[    0.730000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[    1.310000] eth0: Atheros AR8327 switch driver attached.
[    2.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd034, driver=Atheros AR8216/AR8236/AR8316]
[    2.490000] TCP cubic registered
[    2.490000] NET: Registered protocol family 17
[    2.490000] Bridge firewalling registered
[    2.500000] 8021q: 802.1Q VLAN Support v1.8
[    2.510000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    2.510000] Freeing unused kernel memory: 212k freed
[    4.090000] Registered led device: tp-link:blue:qss
[    4.090000] Registered led device: tp-link:blue:system
[    4.100000] Registered led device: tp-link:green:usb1
[    4.100000] Registered led device: tp-link:green:usb2
[    4.100000] Registered led device: tp-link:blue:wlan2g
[    5.470000] eth0: link up (1000Mbps/Full duplex)
[    7.340000] JFFS2 notice: (481) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 14 of xref (0 dead, 4 orphan) found.
[    7.490000] eth0: link down
[    8.800000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[    8.810000] Backport based on wireless-testing.git master-2012-09-07
[    8.820000] compat.git: wireless-testing.git
[    8.860000] cfg80211: Calling CRDA to update world regulatory domain
[    8.890000] cfg80211: World regulatory domain updated:
[    8.890000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    8.900000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.910000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.910000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    8.920000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    8.930000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.160000] usbcore: registered new interface driver usbfs
[    9.160000] usbcore: registered new interface driver hub
[    9.170000] usbcore: registered new device driver usb
[    9.590000] ath: EEPROM regdomain: 0x0
[    9.590000] ath: EEPROM indicates default country code should be used
[    9.590000] ath: doing EEPROM country->regdmn map search
[    9.590000] ath: country maps to regdmn code: 0x3a
[    9.590000] ath: Country alpha2 being used: US
[    9.590000] ath: Regpair used: 0x3a
[    9.600000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[    9.600000] Registered led device: ath9k-phy0
[    9.600000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[    9.600000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[    9.620000] ath: EEPROM regdomain: 0x0
[    9.620000] ath: EEPROM indicates default country code should be used
[    9.620000] ath: doing EEPROM country->regdmn map search
[    9.620000] ath: country maps to regdmn code: 0x3a
[    9.620000] ath: Country alpha2 being used: US
[    9.620000] ath: Regpair used: 0x3a
[    9.620000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[    9.620000] Registered led device: ath9k-phy1
[    9.620000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[    9.630000] cfg80211: Calling CRDA for country: US
[    9.630000] cfg80211: Regulatory domain changed to country: US
[    9.640000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    9.650000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    9.650000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    9.660000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.670000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.680000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    9.680000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[    9.740000] PPP generic driver version 2.4.2
[    9.920000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.080000] NET: Registered protocol family 24
[   10.100000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   10.110000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[   10.110000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[   10.150000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[   10.170000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[   10.170000] hub 1-0:1.0: USB hub found
[   10.180000] hub 1-0:1.0: 1 port detected
[   10.200000] nf_conntrack version 0.5.0 (1979 buckets, 7916 max)
[   10.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   10.500000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[   10.650000] hub 1-1:1.0: USB hub found
[   10.650000] hub 1-1:1.0: 4 ports detected
[   12.840000] eth0: link up (1000Mbps/Full duplex)
[   13.300000] eth0: link down
[   13.310000] device eth0.1 entered promiscuous mode
[   13.310000] device eth0 entered promiscuous mode
[   13.930000] eth0: link up (1000Mbps/Full duplex)
[   13.950000] br-lan: port 1(eth0.1) entered forwarding state
[   13.950000] br-lan: port 1(eth0.1) entered forwarding state
[   15.950000] br-lan: port 1(eth0.1) entered forwarding state
[   19.210000] cfg80211: Calling CRDA for country: FR
[   19.210000] cfg80211: Regulatory domain changed to country: FR
[   19.220000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   19.230000] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   19.230000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   19.240000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   19.250000] cfg80211:   (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[   21.170000] device wlan0 entered promiscuous mode
[   21.430000] br-lan: port 2(wlan0) entered forwarding state
[   21.430000] br-lan: port 2(wlan0) entered forwarding state
[   23.430000] br-lan: port 2(wlan0) entered forwarding state
[   24.760000] device wlan1 entered promiscuous mode
[   25.010000] br-lan: port 3(wlan1) entered forwarding state
[   25.010000] br-lan: port 3(wlan1) entered forwarding state
[   27.010000] br-lan: port 3(wlan1) entered forwarding state
[  708.990000] device wlan0 left promiscuous mode
[  708.990000] br-lan: port 2(wlan0) entered disabled state
[  709.260000] device wlan1 left promiscuous mode
[  709.260000] br-lan: port 3(wlan1) entered disabled state
[  710.790000] device wlan0 entered promiscuous mode
[  711.040000] br-lan: port 2(wlan0) entered forwarding state
[  711.050000] br-lan: port 2(wlan0) entered forwarding state
[  713.050000] br-lan: port 2(wlan0) entered forwarding state
[  714.390000] device wlan1 entered promiscuous mode
[  714.650000] br-lan: port 3(wlan1) entered forwarding state
[  714.650000] br-lan: port 3(wlan1) entered forwarding state
[  716.650000] br-lan: port 3(wlan1) entered forwarding state
[  721.480000] device wlan0 left promiscuous mode
[  721.480000] br-lan: port 2(wlan0) entered disabled state
[  721.770000] device wlan1 left promiscuous mode
[  721.770000] br-lan: port 3(wlan1) entered disabled state
[  724.040000] device wlan0 entered promiscuous mode
[  724.510000] br-lan: port 2(wlan0) entered forwarding state
[  724.520000] br-lan: port 2(wlan0) entered forwarding state
[  726.520000] br-lan: port 2(wlan0) entered forwarding state
[  729.280000] device wlan1 entered promiscuous mode
[  729.540000] br-lan: port 3(wlan1) entered forwarding state
[  729.540000] br-lan: port 3(wlan1) entered forwarding state
[  731.510000] device wlan0 left promiscuous mode
[  731.510000] br-lan: port 2(wlan0) entered disabled state
[  731.540000] br-lan: port 3(wlan1) entered forwarding state
[  731.820000] device wlan1 left promiscuous mode
[  731.820000] br-lan: port 3(wlan1) entered disabled state
[  733.430000] device wlan0 entered promiscuous mode
[  733.690000] br-lan: port 2(wlan0) entered forwarding state
[  733.700000] br-lan: port 2(wlan0) entered forwarding state
[  735.700000] br-lan: port 2(wlan0) entered forwarding state
[  737.020000] device wlan1 entered promiscuous mode
[  737.270000] br-lan: port 3(wlan1) entered forwarding state
[  737.270000] br-lan: port 3(wlan1) entered forwarding state
[  739.270000] br-lan: port 3(wlan1) entered forwarding state
[  748.600000] device wlan0 left promiscuous mode
[  748.600000] br-lan: port 2(wlan0) entered disabled state
[  748.770000] device wlan1 left promiscuous mode
[  748.770000] br-lan: port 3(wlan1) entered disabled state
[  749.910000] device wlan0 entered promiscuous mode
[  750.170000] br-lan: port 2(wlan0) entered forwarding state
[  750.170000] br-lan: port 2(wlan0) entered forwarding state
[  752.170000] br-lan: port 2(wlan0) entered forwarding state
[  753.960000] device wlan1 entered promiscuous mode
[  754.210000] br-lan: port 3(wlan1) entered forwarding state
[  754.220000] br-lan: port 3(wlan1) entered forwarding state
[  756.220000] br-lan: port 3(wlan1) entered forwarding state
[ 1124.850000] device eth0.2 entered promiscuous mode
[ 1124.870000] br-wan: port 1(eth0.2) entered forwarding state
[ 1124.870000] br-wan: port 1(eth0.2) entered forwarding state
[ 1125.130000] device wlan0 left promiscuous mode
[ 1125.140000] br-lan: port 2(wlan0) entered disabled state
[ 1125.670000] device wlan1 left promiscuous mode
[ 1125.670000] br-lan: port 3(wlan1) entered disabled state
[ 1126.870000] br-wan: port 1(eth0.2) entered forwarding state
[ 1128.640000] device wlan0 entered promiscuous mode
[ 1129.100000] br-lan: port 2(wlan0) entered forwarding state
[ 1129.100000] br-lan: port 2(wlan0) entered forwarding state
[ 1131.100000] br-lan: port 2(wlan0) entered forwarding state
[ 1133.240000] device wlan1 entered promiscuous mode
[ 1133.480000] br-lan: port 3(wlan1) entered forwarding state
[ 1133.490000] br-lan: port 3(wlan1) entered forwarding state
[ 1135.490000] br-lan: port 3(wlan1) entered forwarding state
[ 1380.060000] device wlan0 left promiscuous mode
[ 1380.060000] br-lan: port 2(wlan0) entered disabled state
[ 1380.250000] device wlan1 left promiscuous mode
[ 1380.250000] br-lan: port 3(wlan1) entered disabled state
[ 1381.410000] device wlan0 entered promiscuous mode
[ 1381.660000] br-lan: port 2(wlan0) entered forwarding state
[ 1381.670000] br-lan: port 2(wlan0) entered forwarding state
[ 1383.670000] br-lan: port 2(wlan0) entered forwarding state
[ 1385.000000] device wlan1 entered promiscuous mode
[ 1385.250000] br-lan: port 3(wlan1) entered forwarding state
[ 1385.260000] br-lan: port 3(wlan1) entered forwarding state
[ 1387.260000] br-lan: port 3(wlan1) entered forwarding state
[ 1401.410000] device wlan0 left promiscuous mode
[ 1401.410000] br-lan: port 2(wlan0) entered disabled state
[ 1401.680000] device wlan1 left promiscuous mode
[ 1401.680000] br-lan: port 3(wlan1) entered disabled state
[ 1403.200000] device wlan0 entered promiscuous mode
[ 1403.460000] br-lan: port 2(wlan0) entered forwarding state
[ 1403.460000] br-lan: port 2(wlan0) entered forwarding state
[ 1405.460000] br-lan: port 2(wlan0) entered forwarding state
[ 1406.780000] device wlan1 entered promiscuous mode
[ 1407.030000] br-lan: port 3(wlan1) entered forwarding state
[ 1407.030000] br-lan: port 3(wlan1) entered forwarding state
[ 1409.030000] br-lan: port 3(wlan1) entered forwarding state
[ 1427.370000] device wlan0 left promiscuous mode
[ 1427.370000] br-lan: port 2(wlan0) entered disabled state
[ 1427.550000] device wlan1 left promiscuous mode
[ 1427.550000] br-lan: port 3(wlan1) entered disabled state
[ 1428.730000] device wlan0 entered promiscuous mode
[ 1428.990000] br-lan: port 2(wlan0) entered forwarding state
[ 1428.990000] br-lan: port 2(wlan0) entered forwarding state
[ 1430.990000] br-lan: port 2(wlan0) entered forwarding state
[ 1432.880000] device wlan1 entered promiscuous mode
[ 1433.120000] br-lan: port 3(wlan1) entered forwarding state
[ 1433.130000] br-lan: port 3(wlan1) entered forwarding state
[ 1433.150000] device wlan1-1 entered promiscuous mode
[ 1433.160000] br-lan: port 4(wlan1-1) entered forwarding state
[ 1433.160000] br-lan: port 4(wlan1-1) entered forwarding state
[ 1435.130000] br-lan: port 3(wlan1) entered forwarding state
[ 1435.160000] br-lan: port 4(wlan1-1) entered forwarding state
[ 6575.160000] device wlan0 left promiscuous mode
[ 6575.160000] br-lan: port 2(wlan0) entered disabled state
[ 6575.360000] br-lan: port 4(wlan1-1) entered disabled state
[ 6575.360000] device wlan1-1 left promiscuous mode
[ 6575.370000] br-lan: port 4(wlan1-1) entered disabled state
[ 6575.380000] device wlan1 left promiscuous mode
[ 6575.380000] br-lan: port 3(wlan1) entered disabled state
[ 6576.600000] device wlan0 entered promiscuous mode
[ 6576.850000] br-lan: port 2(wlan0) entered forwarding state
[ 6576.860000] br-lan: port 2(wlan0) entered forwarding state
[ 6578.860000] br-lan: port 2(wlan0) entered forwarding state
[ 6580.150000] device wlan1 entered promiscuous mode
[ 6580.400000] br-lan: port 3(wlan1) entered forwarding state
[ 6580.400000] br-lan: port 3(wlan1) entered forwarding state
[ 6582.400000] br-lan: port 3(wlan1) entered forwarding state
[ 6795.350000] br-lan: port 2(wlan0) entered disabled state
[ 6795.510000] device wlan0 left promiscuous mode
[ 6795.510000] br-lan: port 2(wlan0) entered disabled state
[ 6795.700000] br-lan: port 3(wlan1) entered disabled state
[ 6795.770000] device wlan1 left promiscuous mode
[ 6795.770000] br-lan: port 3(wlan1) entered disabled state
[ 6796.960000] device wlan0 entered promiscuous mode
[ 6797.210000] br-lan: port 2(wlan0) entered forwarding state
[ 6797.220000] br-lan: port 2(wlan0) entered forwarding state
[ 6799.220000] br-lan: port 2(wlan0) entered forwarding state
[ 6800.530000] device wlan1 entered promiscuous mode
[ 6800.780000] br-lan: port 3(wlan1) entered forwarding state
[ 6800.780000] br-lan: port 3(wlan1) entered forwarding state
[ 6802.780000] br-lan: port 3(wlan1) entered forwarding state

For information (in French) :
Mode: Master | SSID: XXX
BSSID: C0:4A:00:E4:86:24 | Chiffrement: WPA2 PSK (TKIP, CCMP)
Canal: 36 (5.180 Ghz) | Puissance d'émission: 14 dBm
Signal: 0 dBm | Bruit: -91 dBm
Débit: 0.0 Mbit/s | Pays: FR

Thank you.

(Last edited by Ferguson on 2 Jul 2014, 13:01)

Post #7
jow
2 Jul 2014, 13:22

Erm 11n capable does not imply 5GHz support. In fact most "n" devices do not support 5GHz. Most smartphones don't, many laptops neither.

Post #8
qasdfdsaq
2 Jul 2014, 13:31
Ferguson wrote:

Dual Band Wifi Card = Wifi N acceptance so yes every clients I use have it.

Ermm false.

As for the system logs :

snip

Ermm we seem to be missing the actual important part of the system log, the bit where the wireless is initialized. Unless you've deliberately cut that bit out, you need to increase your syslog buffer. Nonetheless from what I can see the wireless appears to be "Up" so the suspicion rests with your client devices.

jow wrote:

Erm 11n capable does not imply 5GHz support. In fact most "n" devices do not support 5GHz. Most smartphones don't, many laptops neither.

Correct.

Would help if the OP actually told us what wireless card, laptop, or phone he's using.

Post #9
Ferguson
2 Jul 2014, 13:40

This is the wireless I use : http://www.intel.fr/content/www/fr/fr/p … brief.html

So i think you are right. My phone as well has only single band.

Thank you for your help, i think we can close this thread. The trouble comes from the clients.

(Last edited by Ferguson on 2 Jul 2014, 13:41)

The discussion might have continued from here.