A friend forgot the username and password to his Buffalo WZR-HP-AG300H wireless router so he asked me to help him but I've tried everything to get access, to reset it, to reinstall the OpenWRT firmware including using tftp (Linksys tftp), with a ttl to USB converter which I soldered to the router's board and monitoring the opportune point at which to tftp the firmware. The router's default is 192.168.15.1 which I've used with the computer set to the fixed address of 192.168.15.2 and also tried with other addresses such as 192.168.11.1 and 192.168.1.1 without success. I've also tried to telnet into those addresses with port 23 and 24 without success. I've tried to put the router into safe and other modes by inputting f and return and only return at the points specified during boot by monitoring the serial output but that doesn't work. I've also put a 10/100 switch in between the router and the computer but that didn't make it work. This has taken many hours. I rarely give up but this has got me almost there. I need some help. Here's the serial output during boot:
ÿÿ
BUFFALO U-BOOT Ver 1.01
== CPU:680MHz, DDR:340MHz, AHB:170MHz ==
AP96 (ar7100) U-boot 0.0.1
DRAM: 128 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 266k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
Flash: 32 MB
In: serial
Out: serial
Err: serial
Memory Test
uboot use 83F6BFB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 00000000 Writing... Reading...
Memory Test start(84000000) end(88000000) size(04000000)
Pattern 00000000 Writing... Reading...
Memory Test OK
### buf_ver=[1.01] U-Boot Ver.=[1.01]
### build_date(env)=[Jan 14 2011 - 05:47:09] build_date(bin)=[Jan 14 2011 - 05:4
7:09]
ag7100_enet_initialize...
Reading MAC Address from ENV(0x83f8c2fd)
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010{˜eth0: 02:aa:bb:cc:dd:20
eth0 up
Reading MAC Address from ENV(0x83f8c2fd)
Port 4, Neg Success
eth1: Phy Specific Status=0010
eth1: 02:aa:bb:cc:dd:21
eth1 up
eth0 02:AA:BB:CC:DD:20
, eth1 02:AA:BB:CC:DD:21
eth0 link down
tftp server(receive) go, waiting:4[sec]
enet0 port0 up
pll reg 0x18050010: 0x110000 Load address: 0x84000000
checksum bad
checksum bad
checksum bad
TftpServer Timeout;
no file was loaded.
change bootargs
console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7100
-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@32
0k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=128M
## Booting image at bf060000 ...
Image Name: MIPS OpenWrt Linux-2.6.39.4
Created: 2012-04-26 0:21:05 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 870703 Bytes = 850.3 kB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... crc32_fw: bf060040 - bf13496e (len:000d492f) calc...
crc32_fw: range1 bf060040 - bf13496e
OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 2.6.39.4 (user@alf-u10-train1) (gcc version 4.5.4 2
0110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Wed Apr 25 20:20:10 EDT 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.00
0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 32512
[ 0.000000] Kernel command line: board=WZR-HP-AG300H console=ttyS0,115200 ro
otfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126820k/131072k available (2012k kernel code, 4252k reser
ved, 395k data, 184k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, No
des=1
[ 0.000000] NR_IRQS:80
[ 0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is Buffalo WZR-HP-AG300H
[ 2.670000] registering PCI controller with io_map_base unset
[ 2.680000] bio: create slab <bio-0> at 0
[ 2.680000] pci 0000:00:11.0: fixup device configuration
[ 2.690000] pci 0000:00:12.0: fixup device configuration
[ 2.690000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 2.700000] pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI
address [0x10000000-0x1000ffff])
[ 2.700000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[ 2.710000] pci 0000:00:12.0: BAR 0: set to [mem 0x10010000-0x1001ffff] (PCI
address [0x10010000-0x1001ffff])
[ 2.710000] PCI: mapping irq 72 to pin1@0000:00:11.0
[ 2.720000] PCI: mapping irq 73 to pin1@0000:00:12.0
[ 2.720000] Switching to clocksource MIPS
[ 2.730000] NET: Registered protocol family 2
[ 2.730000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.730000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 2.740000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 2.740000] TCP: Hash tables configured (established 4096 bind 4096)
[ 2.750000] TCP reno registered
[ 2.750000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.760000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.760000] NET: Registered protocol family 1
[ 2.780000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.780000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
) (c) 2001-2006 Red Hat, Inc.
[ 2.790000] msgmni has been set to 247
[ 2.800000] io scheduler noop registered
[ 2.800000] io scheduler deadline registered (default)
[ 2.810000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.830000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 2.840000] console [ttyS0] enabled, bootconsole disabled
[ 2.840000] console [ttyS0] enabled, bootconsole disabled
[ 2.850000] Atheros AR71xx SPI Controller driver version 0.2.4
[ 2.860000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 2.870000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 2.870000] Searching for RedBoot partition table in spi0.0 at offset 0xfe000
0
[ 2.960000] Searching for RedBoot partition table in spi0.0 at offset 0xff000
0
[ 3.060000] No RedBoot partition table detected in spi0.0
[ 3.060000] spi0.0: no WRT160NL signature found
[ 3.070000] m25p80 spi0.1: found mx25l12805d, expected m25p80
[ 3.070000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
[ 3.080000] Searching for RedBoot partition table in spi0.1 at offset 0xff000
0
[ 3.170000] No RedBoot partition table detected in spi0.1
[ 3.180000] spi0.1: no WRT160NL signature found
[ 3.180000] Concatenating MTD devices:
[ 3.190000] (0): "spi0.0"
[ 3.190000] (1): "spi0.1"
[ 3.190000] into device "flash"
[ 3.190000] Creating 7 MTD partitions on "flash":
[ 3.200000] 0x000000000000-0x000000040000 : "u-boot"
[ 3.210000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 3.210000] 0x000000050000-0x000000060000 : "art"
[ 3.220000] 0x000000060000-0x000000160000 : "kernel"
[ 3.230000] 0x000000160000-0x000001ff0000 : "rootfs"
[ 3.230000] mtd: partition "rootfs" set to be root filesystem
[ 3.240000] mtd: partition "rootfs_data" created automatically, ofs=590000, l
en=1A60000
[ 3.250000] 0x000000590000-0x000001ff0000 : "rootfs_data"
[ 3.250000] 0x000001ff0000-0x000002000000 : "user_property"
[ 3.260000] 0x000000060000-0x000001ff0000 : "firmware"
[ 3.650000] ag71xx_mdio: probed
[ 3.650000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 4.170000] eth0: AR8316 switch driver attached.
[ 4.190000] ar8316: Using port 4 as switch port
[ 10.240000] eth1: Atheros AG71xx at 0xba000000, irq 5
[ 10.780000] ar8316: Using port 4 as PHY
[ 16.880000] Atheros AR71xx hardware watchdog driver version 0.1.0
[ 16.880000] TCP westwood registered
[ 16.890000] NET: Registered protocol family 17
[ 16.890000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 16.900000] All bugs added by David S. Miller <davem@redhat.com>
[ 16.910000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 16.920000] Freeing unused kernel memory: 184k freed
[ 18.740000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/inp
ut/input0
[ 18.820000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 20.280000] eth0: link up (1000Mbps/Full duplex)
- regular preinit -
[ 22.350000] JFFS2 notice: (446) jffs2_build_xattr_subsystem: complete buildin
g xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 7 of xref (0 dead, 0
orphan) found.
[ 22.810000] SCSI subsystem initialized
[ 23.010000] usbcore: registered new interface driver usbfs
[ 23.010000] usbcore: registered new interface driver hub
[ 23.020000] usbcore: registered new device driver usb
[ 23.540000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.550000] ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller
[ 23.560000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus num
ber 1
[ 23.600000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
[ 23.620000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
[ 23.620000] hub 1-0:1.0: USB hub found
[ 23.630000] hub 1-0:1.0: 2 ports detected
[ 23.710000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 23.720000] ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
[ 23.720000] ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus num
ber 2
[ 23.730000] ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
[ 23.800000] hub 2-0:1.0: USB hub found
[ 23.800000] hub 2-0:1.0: 2 ports detected
[ 23.820000] uhci_hcd: USB Universal Host Controller Interface driver
[ 23.940000] Initializing USB Mass Storage driver...
[ 23.940000] usbcore: registered new interface driver usb-storage
[ 23.950000] USB Mass Storage support registered.
ÿÿ
BUFFALO U-BOOT Ver 1.01
== CPU:680MHz, DDR:340MHz, AHB:170MHz ==
AP96 (ar7100) U-boot 0.0.1
DRAM: 128 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 266k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
Flash: 32 MB
In: serial
Out: serial
Err: serial
Memory Test
uboot use 83F6BFB0 - 84000000
Memory Test start(80000000) end(83F00000) size(03F00000)
Pattern 00000000 Writing... Reading...
Memory Test start(84000000) end(88000000) size(04000000)
Pattern 00000000 Writing... Reading...
Memory Test OK
### buf_ver=[1.01] U-Boot Ver.=[1.01]
### build_date(env)=[Jan 14 2011 - 05:47:09] build_date(bin)=[Jan 14 2011 - 05:4
7:09]
ag7100_enet_initialize...
Reading MAC Address from ENV(0x83f8c2fd)
Port 0, Neg Success
Port 1, Neg Success
Port 2, Neg Success
Port 3, Neg Success
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010
eth0: Phy Specific Status=0010;ˆeth0: 02:aa:bb:cc:dd:20
eth0 up
Reading MAC Address from ENV(0x83f8c2fd)
Port 4, Neg Success
eth1: Phy Specific Status=0010
eth1: 02:aa:bb:cc:dd:21
eth1 up
eth0 02:AA:BB:CC:DD:20
, eth1 02:AA:BB:CC:DD:21
eth0 link down
tftp server(receive) go, waiting:4[sec]
enet0 port0 up
pll reg 0x18050010: 0x110000 Load address: 0x84000000
checksum bad
checksum bad
checksum bad
TftpServer Timeout;
no file was loaded.
change bootargs
console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7100
-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@32
0k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=128M
## Booting image at bf060000 ...
Image Name: MIPS OpenWrt Linux-2.6.39.4
Created: 2012-04-26 0:21:05 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 870703 Bytes = 850.3 kB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... crc32_fw: bf060040 - bf13496e (len:000d492f) calc...
crc32_fw: range1 bf060040 - bf13496e
OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
[ 0.000000] Linux version 2.6.39.4 (user@alf-u10-train1) (gcc version 4.5.4 2
0110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Wed Apr 25 20:20:10 EDT 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7161 rev 2
[ 0.000000] Clocks: CPU:680.000MHz, DDR:340.000MHz, AHB:170.000MHz, Ref:40.00
0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 32512
[ 0.000000] Kernel command line: board=WZR-HP-AG300H console=ttyS0,115200 ro
otfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32
bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126820k/131072k available (2012k kernel code, 4252k reser
ved, 395k data, 184k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, No
des=1
[ 0.000000] NR_IRQS:80
[ 0.000000] Calibrating delay loop... 452.19 BogoMIPS (lpj=2260992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.060000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.070000] MIPS: machine is Buffalo WZR-HP-AG300H
[ 2.670000] registering PCI controller with io_map_base unset
[ 2.680000] bio: create slab <bio-0> at 0
[ 2.680000] pci 0000:00:11.0: fixup device configuration
[ 2.690000] pci 0000:00:12.0: fixup device configuration
[ 2.690000] pci 0000:00:11.0: BAR 0: assigned [mem 0x10000000-0x1000ffff]
[ 2.700000] pci 0000:00:11.0: BAR 0: set to [mem 0x10000000-0x1000ffff] (PCI
address [0x10000000-0x1000ffff])
[ 2.700000] pci 0000:00:12.0: BAR 0: assigned [mem 0x10010000-0x1001ffff]
[ 2.710000] pci 0000:00:12.0: BAR 0: set to [mem 0x10010000-0x1001ffff] (PCI
address [0x10010000-0x1001ffff])
[ 2.710000] PCI: mapping irq 72 to pin1@0000:00:11.0
[ 2.720000] PCI: mapping irq 73 to pin1@0000:00:12.0
[ 2.720000] Switching to clocksource MIPS
[ 2.730000] NET: Registered protocol family 2
[ 2.730000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 2.730000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 2.740000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 2.740000] TCP: Hash tables configured (established 4096 bind 4096)
[ 2.750000] TCP reno registered
[ 2.750000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 2.760000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 2.760000] NET: Registered protocol family 1
[ 2.780000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.780000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY
) (c) 2001-2006 Red Hat, Inc.
[ 2.790000] msgmni has been set to 247
[ 2.800000] io scheduler noop registered
[ 2.800000] io scheduler deadline registered (default)
[ 2.810000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 2.830000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 2.840000] console [ttyS0] enabled, bootconsole disabled
[ 2.840000] console [ttyS0] enabled, bootconsole disabled
[ 2.850000] Atheros AR71xx SPI Controller driver version 0.2.4
[ 2.860000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 2.870000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 2.870000] Searching for RedBoot partition table in spi0.0 at offset 0xfe000
0
[ 2.960000] Searching for RedBoot partition table in spi0.0 at offset 0xff000
0
[ 3.060000] No RedBoot partition table detected in spi0.0
[ 3.060000] spi0.0: no WRT160NL signature found
[ 3.070000] m25p80 spi0.1: found mx25l12805d, expected m25p80
[ 3.070000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
[ 3.080000] Searching for RedBoot partition table in spi0.1 at offset 0xff000
0
[ 3.170000] No RedBoot partition table detected in spi0.1
[ 3.180000] spi0.1: no WRT160NL signature found
[ 3.180000] Concatenating MTD devices:
[ 3.190000] (0): "spi0.0"
[ 3.190000] (1): "spi0.1"
[ 3.190000] into device "flash"
[ 3.190000] Creating 7 MTD partitions on "flash":
[ 3.200000] 0x000000000000-0x000000040000 : "u-boot"
[ 3.210000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 3.210000] 0x000000050000-0x000000060000 : "art"
[ 3.220000] 0x000000060000-0x000000160000 : "kernel"
[ 3.230000] 0x000000160000-0x000001ff0000 : "rootfs"
[ 3.230000] mtd: partition "rootfs" set to be root filesystem
[ 3.240000] mtd: partition "rootfs_data" created automatically, ofs=590000, l
en=1A60000
[ 3.250000] 0x000000590000-0x000001ff0000 : "rootfs_data"
[ 3.250000] 0x000001ff0000-0x000002000000 : "user_property"
[ 3.260000] 0x000000060000-0x000001ff0000 : "firmware"
[ 3.650000] ag71xx_mdio: probed
[ 3.650000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 4.170000] eth0: AR8316 switch driver attached.
[ 4.190000] ar8316: Using port 4 as switch port
[ 10.240000] eth1: Atheros AG71xx at 0xba000000, irq 5
[ 10.780000] ar8316: Using port 4 as PHY
[ 16.880000] Atheros AR71xx hardware watchdog driver version 0.1.0
[ 16.880000] TCP westwood registered
[ 16.890000] NET: Registered protocol family 17
[ 16.890000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 16.900000] All bugs added by David S. Miller <davem@redhat.com>
[ 16.910000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 16.920000] Freeing unused kernel memory: 184k freed
[ 18.740000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/inp
ut/input0
[ 18.820000] Button Hotplug driver version 0.4.1
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 20.280000] eth0: link up (1000Mbps/Full duplex)
- regular preinit -
[ 22.350000] JFFS2 notice: (446) jffs2_build_xattr_subsystem: complete buildin
g xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 7 of xref (0 dead, 0
orphan) found.
[ 22.810000] SCSI subsystem initialized
[ 23.010000] usbcore: registered new interface driver usbfs
[ 23.010000] usbcore: registered new interface driver hub
[ 23.020000] usbcore: registered new device driver usb
[ 23.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.540000] ar71xx-ehci ar71xx-ehci: Atheros AR71xx built-in EHCI controller
[ 23.550000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus num
ber 1
[ 23.580000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
[ 23.600000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
[ 23.600000] hub 1-0:1.0: USB hub found
[ 23.610000] hub 1-0:1.0: 2 ports detected
[ 23.690000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 23.700000] ar71xx-ohci ar71xx-ohci: Atheros AR71xx built-in OHCI controller
[ 23.700000] ar71xx-ohci ar71xx-ohci: new USB bus registered, assigned bus num
ber 2
[ 23.710000] ar71xx-ohci ar71xx-ohci: irq 14, io mem 0x1c000000
[ 23.780000] hub 2-0:1.0: USB hub found
[ 23.780000] hub 2-0:1.0: 2 ports detected
[ 23.800000] uhci_hcd: USB Universal Host Controller Interface driver
[ 23.920000] Initializing USB Mass Storage driver...
[ 23.920000] usbcore: registered new interface driver usb-storage
[ 23.930000] USB Mass Storage support registered.
switching to jffs2
- init -
[ 44.160000] eth0: link down
Please press Enter to activate this console. [ 44.480000] Compat-wireless back
port release: compat-wireless-2011-11-08-1-g4ab9b62
[ 44.480000] Backport based on wireless-testing.git master-2011-11-15
[ 44.700000] cfg80211: Calling CRDA to update world regulatory domain
[ 45.240000] cfg80211: World regulatory domain updated:
[ 45.240000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g
ain, max_eirp)
[ 45.250000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 45.260000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 45.270000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[ 45.280000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 45.280000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 45.880000] PCI: Enabling device 0000:00:11.0 (0000 -> 0002)
[ 45.890000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72
[ 45.900000] PCI: Enabling device 0000:00:12.0 (0000 -> 0002)
[ 45.920000] ieee80211 phy1: Atheros AR9280 Rev:2 mem=0xb0010000, irq=73
[ 45.930000] cfg80211: Calling CRDA for country: US
[ 45.990000] cfg80211: Regulatory domain changed to country: US
[ 45.990000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_g
ain, max_eirp)
[ 46.000000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2700 mBm)
[ 46.010000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
1700 mBm)
[ 46.020000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 46.030000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 46.030000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[ 46.040000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
3000 mBm)
[ 46.300000] PPP generic driver version 2.4.2
[ 46.490000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 46.660000] NET: Registered protocol family 24
[ 46.840000] nf_conntrack version 0.5.0 (1984 buckets, 7936 max)
[ 48.200000] device eth0.5 entered promiscuous mode
[ 48.210000] device eth0 entered promiscuous mode
[ 48.750000] device eth0.4 entered promiscuous mode
[ 48.760000] eth0: link up (1000Mbps/Full duplex)
[ 48.760000] br-lan: port 1(eth0.5) entering forwarding state
[ 48.770000] br-lan: port 1(eth0.5) entering forwarding state
[ 48.800000] br-pub: port 1(eth0.4) entering forwarding state
[ 48.810000] br-pub: port 1(eth0.4) entering forwarding state
[ 51.970000] device wlan0 entered promiscuous mode
[ 51.970000] br-lan: port 2(wlan0) entering forwarding state
[ 51.980000] br-lan: port 2(wlan0) entering forwarding state
[ 54.570000] device wlan0 left promiscuous mode
[ 54.580000] br-lan: port 2(wlan0) entering forwarding state
[ 54.670000] device wlan0 entered promiscuous mode
[ 54.680000] br-lan: port 2(wlan0) entering forwarding state
[ 54.680000] br-lan: port 2(wlan0) entering forwarding state
(Last edited by Grim_Reaper on 24 Jun 2014, 03:52)