Asus RT-N15U
CPU1: Broadcom BCM47186B0 (500 MHz)
FLA1: 8 MiB (Macronix Model?)
RAM1: 64 MiB (Micron MT47H32M16HR-3:F x 1)
WI1 chip1: Broadcom BCM47186B0
WI1 802dot11 protocols: bgn
WI1 MIMO config: 2x2:2
WI1 antenna connector: none
ETH chip1: Broadcom BCM47186B0
Switch: Broadcom BCM53125
LAN speed: 10/100/1000
LAN ports: 4
WAN ports: 1
/snapshots/trunk/brcm47xx/openwrt-brcm47xx-squashfs.trx 22-Apr-2014
root@OpenWrt:/# dmesg
[ 0.000000] Linux version 3.10.36 (openwrt@gb-13) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40535) ) #1 Tue Apr 22 03:16:44 UTC 2014
[ 0.000000] CPU revision is: 00019749 (MIPS 74Kc)
[ 0.000000] bcm47xx: using bcma bus
[ 0.000000] bcma: bus0: Found chip with id 0x5357, rev 0x02 and package 0x0A
[ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x26, class 0x0)
[ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x04, class 0x0)
[ 0.000000] bcma: bus0: Found rev 9 PMU (capabilities 0x28A42A09)
[ 0.000000] bcma: bus0: Found serial flash
[ 0.000000] bcma: bus0: Found M25P64 serial flash (size: 8192KiB, blocksize: 0x10000, blocks: 128)
[ 0.000000] bcma: bus0: Early bus registered
[ 0.000000] MIPS: machine is Asus RT-N15U
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 802dcb80, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61468k/65536k available (2417k kernel code, 4068k reserved, 591k data, 184k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Setting up vectored interrupts
[ 0.060000] Calibrating delay loop... 249.44 BogoMIPS (lpj=1247232)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.090000] Switching to clocksource MIPS
[ 0.100000] NET: Registered protocol family 2
[ 0.100000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.100000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.100000] TCP: Hash tables configured (established 512 bind 512)
[ 0.100000] TCP: reno registered
[ 0.100000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.100000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] PCI: CLS 0 bytes, default 32
[ 0.100000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1C, class 0x0)
[ 0.100000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x03, class 0x0)
[ 0.100000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x05, class 0x0)
[ 0.100000] bcma: bus0: Core 5 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x02, class 0x0)
[ 0.100000] bcma: bus0: Core 6 found: I2S (manuf 0x4BF, id 0x834, rev 0x02, class 0x0)
[ 0.100000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x0B, class 0x0)
[ 0.110000] can not parse nvram name sb/1/boardnum(null) with value ac:22:0b:bd:c2:e2 got -22
[ 0.350000] bcma: bus0: Using SPROM revision 8 provided by platform.
[ 0.350000] bcma: bus0: PMU resource config unknown or not needed for device 0x5357
[ 0.350000] bcma: bus0: Workarounds unknown or not needed for device 0x5357
[ 0.350000] bcma: bus0: Initializing MIPS core...
[ 0.350000] bcma: bus0: set_irq: core 0x0812, irq 3 => 3
[ 0.350000] bcma: bus0: set_irq: core 0x082d, irq 4 => 4
[ 0.350000] bcma: bus0: set_irq: core 0x0819, irq 5 => 5
[ 0.350000] bcma: bus0: set_irq: core 0x0800, irq 2 => 2
[ 0.350000] bcma: bus0: set_irq: core 0x0834, irq 2 => 2
[ 0.350000] bcma: bus0: IRQ reconfiguration done
[ 0.350000] bcma: core 0x0800, irq : 2(S)* 3 4 5 6 D I
[ 0.350000] bcma: core 0x082c, irq : 2(S) 3 4 5 6 D I*
[ 0.350000] bcma: core 0x0812, irq : 2(S) 3* 4 5 6 D I
[ 0.350000] bcma: core 0x082d, irq : 2(S) 3 4* 5 6 D I
[ 0.350000] bcma: core 0x0819, irq : 2(S) 3 4 5* 6 D I
[ 0.350000] bcma: core 0x082e, irq : 2(S) 3 4 5 6 D* I
[ 0.350000] bcma: core 0x0834, irq : 2(S)* 3 4 5 6 D I
[ 0.350000] bcma: core 0x080e, irq : 2(S) 3 4 5 6 D I*
[ 0.360000] bcma: bus0: Bus registered
[ 0.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.360000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.360000] msgmni has been set to 120
[ 0.360000] io scheduler noop registered
[ 0.360000] io scheduler deadline registered (default)
[ 0.360000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.390000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.750000] console [ttyS0] enabled
[ 0.880000] 5 bcm47xxpart partitions found on MTD device bcm47xxsflash
[ 0.880000] Creating 5 MTD partitions on "bcm47xxsflash":
[ 0.890000] 0x000000000000-0x000000020000 : "boot"
[ 0.900000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.910000] 0x00000002001c-0x00000018dc00 : "linux"
[ 0.910000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.930000] 0x00000018dc00-0x0000007f0000 : "rootfs"
[ 0.930000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.950000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.950000] mtd: partition "rootfs_data" created automatically, ofs=0x380000, len=0x470000
[ 0.960000] 0x000000380000-0x0000007f0000 : "rootfs_data"
[ 0.970000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.980000] libphy: Fixed MDIO Bus: probed
[ 0.990000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds)
[ 1.000000] GPIO_WDT: failed to register misc device
[ 1.000000] TCP: cubic registered
[ 1.000000] NET: Registered protocol family 17
[ 1.010000] Bridge firewalling registered
[ 1.010000] 8021q: 802.1Q VLAN Support v1.8
[ 1.030000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.040000] Freeing unused kernel memory: 184K (802f2000 - 80320000)
[ 4.740000] pps_core: LinuxPPS API ver. 1 registered
[ 4.740000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 4.760000] PTP clock support registered
[ 4.770000] bgmac bcma0:1: Found PHY addr: 30 (NOREGS)
[ 4.780000] bgmac bcma0:1: Support for Roboswitch not implemented
[ 4.790000] libphy: bgmac mii bus: probed
[ 4.870000] b53_common: found switch: BCM53125, rev 4
[ 4.880000] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 6.880000] libphy: bgmac-0-0:1e - Link is Up - 1000/Full
[ 10.370000] jffs2: notice: (239) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 39 of xref (0 dead, 2 orphan) found.
[ 13.920000] NET: Registered protocol family 10
[ 13.940000] nf_conntrack version 0.5.0 (963 buckets, 3852 max)
[ 13.960000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.990000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 14.000000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 14.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.070000] xt_time: kernel timezone is -0000
[ 14.120000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.120000] cfg80211: World regulatory domain updated:
[ 14.130000] cfg80211: DFS Master region: unset
[ 14.130000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 14.140000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.150000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.160000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.170000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.180000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 14.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 14.270000] PPP generic driver version 2.4.2
[ 14.280000] NET: Registered protocol family 24
[ 21.560000] device eth0.1 entered promiscuous mode
[ 21.570000] device eth0 entered promiscuous mode
[ 21.580000] br-lan: port 1(eth0.1) entered forwarding state
[ 21.580000] br-lan: port 1(eth0.1) entered forwarding state
[ 22.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 22.950000] libphy: bgmac-0-0:1e - Link is Up - 1000/Full
[ 23.580000] br-lan: port 1(eth0.1) entered forwarding state
Wifi dont work. i try kmod-b43, kmod-brcmsmac, kmod-brcm-wl drivers.
(Last edited by er2f on 22 Apr 2014, 14:09)