OpenWrt Forum Archive

Topic: Tenda FH303 v2, new cheapest high power wifi router.

The content of this topic has been archived on 12 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Just 25$. I'm edited wiki here: https://wikidevi.com/wiki/Tenda_FH303_v2

CPU: BCM5357C0 300mhz.
Flash: 4MBytes. GigaDevice GD25Q32BSIG
RAM: 32MBytes. Winbond W9425G6JH
serial: 115200 8n1
Device use two skywork 2.4ghz amplifier SE2605L.

CFE bootloader log:

CFE version 5.100.138.3 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: 2011-05-26 10:33:50 4 (richard@aeteam.com)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 64 64KB blocks; total size 4MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.3
CPU type 0x19749: 300MHz
Tot mem: 32768 KBytes

CFE mem:    0x80700000 - 0x80798550 (623952)
Data:       0x8072E3A0 - 0x807315C0 (12832)
BSS:        0x807315C0 - 0x80732550 (3984)
Heap:       0x80732550 - 0x80796550 (409600)
Stack:      0x80796550 - 0x80798550 (8192)
Text:       0x80700000 - 0x8072E39C (189340)

Device eth0:  hwaddr C8-3A-35-0F-72-08, ipaddr 192.168.1.254, mask 255.255.255.0
        gateway not set, nameserver not set
Loader:raw Filesys:tftp Dev:eth0 File:192.168.0.100:vmlinuz Options:(null)
Loading: Failed.
Could not load 192.168.0.100:vmlinuz: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: ..... 2815676 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
IP Filter: v3.4.35 initialized.  Default = pass all, Logging = disabled
PCI: no core
PCI: no core
PCI: Fixing up bus 0
wl_pci_probe: find [14e4:4329] bus 0 slot 1 func 0 irq 1

eCos Router/AP V5.110.27.21 (Compiled at 02:21:49 on Jun 28 2013)
sys_led_test_gpio=6
=============342Using pin 6 for sys_led output
wps_led_test_gpio=7
System start
vlan1: VLAN interface created
vlan2: VLAN interface created
wlconf: PHYTYPE: 4
EAPD task started
initWebs: lanip=[192.168.1.254]
NAS task started
CLI> envram show
antswctl2g=0x1
boardflags=0x710
boardflags2=0x1000
boardnum=396
boardrev=0x1155
boardtype=0x058e
boot_wait=on
clkfreq=300,150,75
et0macaddr=C8:3A:35:0F:72:08
et0mdcport=0
et0phyaddr=30
gpio20=wps_button
gpio6=sys_led
gpio7=wps_led
lan_ipaddr=192.168.0.1
lan_netmask=255.255.255.0
landevs=vlan1 wl0
pmon_ver=CFE 5.100.138.3
reset_gpio=20
sb/1/aa2g=0x7
sb/1/ag0=0x0
sb/1/ag1=0x0
sb/1/ag2=0x0
sb/1/ag3=0xff
sb/1/antswctl2g=0x1
sb/1/antswitch=0x3
sb/1/boardflags=0x710
sb/1/boardflags2=0x1000
sb/1/bw40po=0x0
sb/1/bwduppo=0x0
sb/1/bxa2g=0x3
sb/1/cck2gpo=0x0
sb/1/ccode=US
sb/1/cddpo=0x0
sb/1/devid=0x4329
sb/1/extpagain2g=0x3
sb/1/itt2ga0=0x20
sb/1/itt2ga1=0x20
sb/1/ledbh0=11
sb/1/ledbh1=11
sb/1/ledbh2=11
sb/1/ledbh3=11
sb/1/ledbh5=7
sb/1/ledbh6=11
sb/1/leddc=0xffff
sb/1/macaddr=C8:3A:35:0F:72:08
sb/1/maxp2ga0=0x6c
sb/1/maxp2ga1=0x6c
sb/1/mcs2gpo0=0x2200
sb/1/mcs2gpo1=0x6644
sb/1/mcs2gpo2=0x2200
sb/1/mcs2gpo3=0x6644
sb/1/mcs2gpo4=0x4422
sb/1/mcs2gpo5=0x8866
sb/1/mcs2gpo6=0x4422
sb/1/mcs2gpo7=0x8866
sb/1/ofdm2gpo=0x66442200
sb/1/opo=0x0
sb/1/pa2gw0a0=0xfe19
sb/1/pa2gw0a1=0xfe40
sb/1/pa2gw1a0=0x1a80
sb/1/pa2gw1a1=0x1ce0
sb/1/pa2gw2a0=0xf927
sb/1/pa2gw2a1=0xf8b7
sb/1/pdetrange2g=0x3
sb/1/regrev=23
sb/1/rssisav2g=0x7
sb/1/rssismc2g=0xf
sb/1/rssismf2g=0xf
sb/1/rxchain=0x3
sb/1/rxpo2g=0xff
sb/1/sromrev=8
sb/1/stbcpo=0x0
sb/1/temps_hysteresis=5
sb/1/temps_period=5
sb/1/tempthresh=120
sb/1/tri2g=0xff
sb/1/triso2g=0x5
sb/1/tssipos2g=0x1
sb/1/txchain=0x3
sdram_config=0x103
sdram_init=0x0000
sdram_ncdl=0x00000000
sdram_refresh=0x0000
tenda_tftp_name=192.168.0.100:vmlinuz
vlan1hwname=et0
vlan1ports=1 2 3 4 5*
vlan2hwname=et0
vlan2ports=0 5
wait_time=10
wandevs=vlan2
watchdog=0
wl_msglevel=0x1
xtalfreq=20000
wps_device_pin=xxxxxxxx

PunBB bbcode test

(Last edited by congquynh284 on 17 Feb 2014, 18:20)

is there no custom firmware for this particular router?

The discussion might have continued from here.