I did a little google searching and found https://dev.openwrt.org/ticket/6379 which says that Kamakazie R18921 fully supports the Linksys WRT300N-v1.1, Yes the supported devices list does not reflect this and I don't see any reference to Attitude Adjustment or Backfire supporting this device. Can anyone suggest?
Topic: Linksys WRT300N-V1.1 Support
The content of this topic has been archived between 16 Apr 2018 and 20 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Page 1 of 2
Could it perhaps be one of these?
trunk http://downloads.openwrt.org/snapshots/ … uashfs.bin
AA http://downloads.openwrt.org/attitude_a … uashfs.bin
Backfire http://downloads.openwrt.org/backfire/1 … uashfs.bin
Well I have downloaded and tried the following:
http://downloads.openwrt.org/attitude_a … uashfs.bin
Flashes, Installs, Boots but ifconfig in serial console shows no eth0 only lo and watching the boot the roboswitch probe finds no eth0, eth1, eth2, or eth3
http://downloads.openwrt.org/backfire/1 … uashfs.bin
Flashes, Installs, Boots but ifconfig in serial console shows no eth0 only lo and watching the boot the roboswitch probe finds no eth0, eth1, eth2, or eth3
http://downloads.openwrt.org/backfire/1 … uashfs.bin
Flashes, Installs, Boots but ifconfig in serial console shows no eth0 only lo and watching the boot the roboswitch probe finds no eth0, eth1, eth2, or eth3
http://downloads.openwrt.org/kamikaze/8 … uashfs.bin
Would not complete a successful flash install - plan to retry for 4th time tomorrow
http://downloads.openwrt.org/kamikaze/8 … uashfs.bin
Would not complete a successful flash install - plan to retry for 4th time tomorrow
Anyone with a Linksys WRT300N-V1.1 that works on OpenWrt please enlighten me as to what you are running.
For the stable ethernet support (and generally "everything") it may be the best idea to install BB (which is trunk AKA snapshot) right now.
Can you install version from http://downloads.openwrt.org/snapshots/trunk/brcm47xx/ (but please make a clean install, not an upgrade) and see if it works for you? If it doesn't, please provide full boot log (you have serial console, that's great!).
Bottom Line - NO JOY WITH TRUNk BB, Steps Taken and Boot Log from Serial Below:
OK downloaded http://downloads.openwrt.org/snapshots/ … uashfs.bin and proceeded to flash/install.
Step 1 - Apply power with Serial Console connected and press <Ctril-C> to get CFE> prompt.
Step 2 - At CFE Prompt enter command "nvram erase".
Step 3 - Command returns code 0 meaning successful compeltion.
Step 4 - At CFE Prompt enter command "flash -ctheader : flash1.trx"
Step 5 - At same time as CFE prompt command is entered start tftp2 serving file http://downloads.openwrt.org/snapshots/ … uashfs.bin to unit.
Step 6 - wait thru several reboots and see that install was a success, but the eth0 still fails to work.
Step 7 - Remove Power, close serial session and open a fresh serial session with logging.
Step 8 - apply power and wait till serial output ends.
Step 9 - Close serial session and post log after this message. COULD NOT FIND ATTACH FEATURE SO POSTING LOG BELOW:
THANKS TO ZAJEC FOR POINTING OUT THE CODE: TAG FEATURE FOR POSTING TEXT FILES.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.01.08 21:36:52 =~=~=~=~=~=~=~=~=~=~=~=
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0x109400 (1086464) (0xBC149400)
Header CRC: 0x1F2047FD
Calculate CRC: 0x1F2047FD
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39203) ) #1 Mon Jan 6 21:58:02 PST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28992k/32768k available (2413k kernel code, 3776k reserved, 587k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.060000] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.600000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.970000] console [ttyS0] enabled
[ 0.990000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.010000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.020000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.030000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.030000] Amd/Fujitsu Extended Query version 1.0.
[ 1.040000] number of CFI chips: 1
[ 1.080000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.080000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.090000] 0x000000000000-0x000000040000 : "boot"
[ 1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.110000] 0x000000040960-0x000000149400 : "linux"
[ 1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.130000] 0x000000149400-0x0000007f0000 : "rootfs"
[ 1.140000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.160000] mtd: partition "rootfs_data" created automatically, ofs=0x320000, len=0x4d0000
[ 1.170000] 0x000000320000-0x0000007f0000 : "rootfs_data"
[ 1.180000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.190000] libphy: Fixed MDIO Bus: probed
[ 1.200000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.210000] GPIO_WDT: failed to register misc device
[ 1.210000] TCP: cubic registered
[ 1.220000] NET: Registered protocol family 17
[ 1.220000] Bridge firewalling registered
[ 1.230000] can: controller area network core (rev 20120528 abi 9)
[ 1.230000] NET: Registered protocol family 29
[ 1.240000] 8021q: 802.1Q VLAN Support v1.8
[ 1.250000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.260000] Freeing unused kernel memory: 192K (802f0000 - 80320000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.770000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.770000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.780000] pps_core: LinuxPPS API ver. 1 registered
[ 5.780000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.800000] PTP clock support registered
[ 5.810000] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 5.840000] tg3.c:v3.132 (May 21, 2013)
[ 5.850000] libphy: tg3 mdio bus: probed
[ 5.860000] b53_common: found switch: BCM5325, rev 0
[ 5.870000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.880000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 5.890000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 5.900000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.870000] tg3 0000:01:00.0 eth0: Link is down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.590000] NET: Registered protocol family 10
[ 14.610000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 14.630000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.660000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 14.670000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 14.690000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.770000] xt_time: kernel timezone is -0000
[ 14.810000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.810000] cfg80211: World regulatory domain updated:
[ 14.820000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.830000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.830000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.840000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.850000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 14.860000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 14.870000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 14.990000] PPP generic driver version 2.4.2
[ 15.000000] NET: Registered protocol family 24
[ 15.060000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.160000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.220000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 15.280000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0x109400 (1086464) (0xBC149400)
Header CRC: 0x1F2047FD
Calculate CRC: 0x1F2047FD
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39203) ) #1 Mon Jan 6 21:58:02 PST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28992k/32768k available (2413k kernel code, 3776k reserved, 587k data, 192k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.060000] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.600000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.970000] console [ttyS0] enabled
[ 0.990000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.010000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.020000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.030000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.030000] Amd/Fujitsu Extended Query version 1.0.
[ 1.040000] number of CFI chips: 1
[ 1.080000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.080000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.090000] 0x000000000000-0x000000040000 : "boot"
[ 1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.110000] 0x000000040960-0x000000149400 : "linux"
[ 1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.130000] 0x000000149400-0x0000007f0000 : "rootfs"
[ 1.140000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.160000] mtd: partition "rootfs_data" created automatically, ofs=0x320000, len=0x4d0000
[ 1.170000] 0x000000320000-0x0000007f0000 : "rootfs_data"
[ 1.180000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.190000] libphy: Fixed MDIO Bus: probed
[ 1.200000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.210000] GPIO_WDT: failed to register misc device
[ 1.210000] TCP: cubic registered
[ 1.220000] NET: Registered protocol family 17
[ 1.220000] Bridge firewalling registered
[ 1.230000] can: controller area network core (rev 20120528 abi 9)
[ 1.230000] NET: Registered protocol family 29
[ 1.240000] 8021q: 802.1Q VLAN Support v1.8
[ 1.250000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.260000] Freeing unused kernel memory: 192K (802f0000 - 80320000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.770000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.770000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.780000] pps_core: LinuxPPS API ver. 1 registered
[ 5.790000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.800000] PTP clock support registered
[ 5.820000] bgmac: Broadcom 47xx GBit MAC driver loaded
[ 5.840000] tg3.c:v3.132 (May 21, 2013)
[ 5.850000] libphy: tg3 mdio bus: probed
[ 5.860000] b53_common: found switch: BCM5325, rev 0
[ 5.870000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.880000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 5.890000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 5.900000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.870000] tg3 0000:01:00.0 eth0: Link is down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.590000] NET: Registered protocol family 10
[ 14.610000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 14.630000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.670000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 14.680000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 14.690000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 14.770000] xt_time: kernel timezone is -0000
[ 14.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 14.820000] cfg80211: World regulatory domain updated:
[ 14.830000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.840000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.840000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 14.850000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 14.860000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 14.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 14.880000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 15.000000] PPP generic driver version 2.4.2
[ 15.020000] NET: Registered protocol family 24
[ 15.070000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.180000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.240000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 15.300000] Broadcom 43xx-legacy driver loaded [ Features: PLD ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0](Last edited by boblfoot on 10 Jan 2014, 23:22)
I think this tells us something about this bug:
[ 8.870000] tg3 0000:01:00.0 eth0: Link is downIt seems tg3 believes there is no switch attached to the SoC. I'll ask Hauke about that, I don't really have much experience with tg3.
Thanks I'll keep watching for an update. I really would like to get this switch running OpenWrt sometime. It ran DDWrt-mini version just fine, but that would not support ipv6 and I'd like to move the LAN to IPv6 for learning sake.
This looks like the switch reset performed a device reset, it is probably using the wrong pin. I saw in a other switch driver some special workaround for this device.
Please try this patch on top of trunk: http://hauke-m.de/files/openwrt/wrt300n-b53.patch
I am correct in asuming that I need the full buildroot and sources to apply the patch and will have to generate my own openwrt-wrt300b-v11.bin file for flashing?
Ok I have a buildroot VM setup and have built openwrt 2x so far. Now how and where do I place your patch. The wiki instructions {http://wiki.openwrt.org/doc/devel/patches} are less than clear about importing an existing patch. A little help would be appreciated.
Just apply it in the root of OpenWrt's repo. Like "git am wrt300n-b53.patch"
well placing the patch in ~/Downloads/wrt300n-b53.patch and then switching to ~/openwrt/trunk and runing the command git am ~/Downloads/wrt300n-b53.patch fails for fatal: not a git repository.
Now if I place the patch in ~/openwrt/trunk/target/linux/generic/patches-3.12 as 780-openwrt-b53.patch and after returning to ~/openwrt/trunk/ I run make target/linux/update package/index V=s followed by make. I get what I think is the patched bin file. Does this sound about right someone?
just go cd into the directoru ~/openwrt/trunk
and apply the patch: git am ../wrt300n-b53.patch
How did you get OpenWrt source if not using git? svn? If so, you can try
patch -p1 < ~/Downloads/wrt300n-b53.patch
Source was obtained with svn co svn://svn.openwrt.org/openwrt/trunk/ command as found in wiki --> http://wiki.openwrt.org/doc/howto/build … ent.tree1.
Zajec the patch -p1 command appears to work. a least patch was applied and source is rebuilding.
Ok here is the serial console output of the patched.bin when flashed. And there is no change.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.01.10 16:31:00 =~=~=~=~=~=~=~=~=~=~=~=
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0xFCC00 (1035264) (0xBC13CC00)
Header CRC: 0x77A4A09E
Calculate CRC: 0x77A4A09E
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (buildroot@localhost.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39211) ) #2 Fri Jan 10 16:04:45 EST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29128k/32768k available (2278k kernel code, 3640k reserved, 574k data, 212k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.580000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.960000] console [ttyS0] enabled
[ 0.980000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.000000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.010000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.020000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.020000] Amd/Fujitsu Extended Query version 1.0.
[ 1.030000] number of CFI chips: 1
[ 1.070000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.070000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.080000] 0x000000000000-0x000000040000 : "boot"
[ 1.090000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.100000] 0x000000040960-0x00000013cc00 : "linux"
[ 1.110000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.120000] 0x00000013cc00-0x0000007f0000 : "rootfs"
[ 1.130000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.150000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000
[ 1.160000] 0x000000300000-0x0000007f0000 : "rootfs_data"
[ 1.170000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.180000] libphy: Fixed MDIO Bus: probed
[ 1.190000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.200000] GPIO_WDT: failed to register misc device
[ 1.200000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.210000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.890000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.890000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.910000] pps_core: LinuxPPS API ver. 1 registered
[ 5.910000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.930000] PTP clock support registered
[ 5.950000] tg3.c:v3.132 (May 21, 2013)
[ 5.960000] libphy: tg3 mdio bus: probed
[ 5.970000] b53_common: found switch: BCM5325, rev 0
[ 5.980000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.990000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 6.000000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 6.010000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.980000] tg3 0000:01:00.0 eth0: Link is down
4
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
BusyBox v1.19.4 (2014-01-10 15:44:33 EST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r39211)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@(none):/# [ 14.910000] NET: Registered protocol family 10
[ 14.930000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 14.950000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.990000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 15.000000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 15.010000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.090000] xt_time: kernel timezone is -0000
[ 15.140000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.140000] cfg80211: World regulatory domain updated:
[ 15.150000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.160000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.160000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.170000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.180000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.200000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 15.320000] PPP generic driver version 2.4.2
[ 15.340000] NET: Registered protocol family 24
[ 15.390000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.500000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.560000] Broadcom 43xx driver loaded [ Features: PNL ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0xFCC00 (1035264) (0xBC13CC00)
Header CRC: 0x77A4A09E
Calculate CRC: 0x77A4A09E
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (buildroot@localhost.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39211) ) #2 Fri Jan 10 16:04:45 EST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29128k/32768k available (2278k kernel code, 3640k reserved, 574k data, 212k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.580000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.960000] console [ttyS0] enabled
[ 0.980000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.000000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.010000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.020000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.020000] Amd/Fujitsu Extended Query version 1.0.
[ 1.030000] number of CFI chips: 1
[ 1.070000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.070000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.080000] 0x000000000000-0x000000040000 : "boot"
[ 1.090000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.100000] 0x000000040960-0x00000013cc00 : "linux"
[ 1.110000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.120000] 0x00000013cc00-0x0000007f0000 : "rootfs"
[ 1.130000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.150000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000
[ 1.160000] 0x000000300000-0x0000007f0000 : "rootfs_data"
[ 1.170000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.180000] libphy: Fixed MDIO Bus: probed
[ 1.190000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.200000] GPIO_WDT: failed to register misc device
[ 1.200000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.210000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.890000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.890000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.910000] pps_core: LinuxPPS API ver. 1 registered
[ 5.910000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.930000] PTP clock support registered
[ 5.950000] tg3.c:v3.132 (May 21, 2013)
[ 5.960000] libphy: tg3 mdio bus: probed
[ 5.970000] b53_common: found switch: BCM5325, rev 0
[ 5.980000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.990000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 6.000000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 6.010000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.970000] tg3 0000:01:00.0 eth0: Link is down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.860000] NET: Registered protocol family 10
[ 14.880000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 14.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.930000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 14.940000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 14.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.030000] xt_time: kernel timezone is -0000
[ 15.080000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.080000] cfg80211: World regulatory domain updated:
[ 15.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.110000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.120000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.130000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.140000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 15.270000] PPP generic driver version 2.4.2
[ 15.290000] NET: Registered protocol family 24
[ 15.340000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.440000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.500000] Broadcom 43xx driver loaded [ Features: PNL ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0xFCC00 (1035264) (0xBC13CC00)
Header CRC: 0x77A4A09E
Calculate CRC: 0x77A4A09E
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (buildroot@localhost.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39211) ) #2 Fri Jan 10 16:04:45 EST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29128k/32768k available (2278k kernel code, 3640k reserved, 574k data, 212k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.580000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.960000] console [ttyS0] enabled
[ 0.980000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.000000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.010000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.020000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.020000] Amd/Fujitsu Extended Query version 1.0.
[ 1.030000] number of CFI chips: 1
[ 1.070000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.070000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.080000] 0x000000000000-0x000000040000 : "boot"
[ 1.090000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.100000] 0x000000040960-0x00000013cc00 : "linux"
[ 1.110000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.120000] 0x00000013cc00-0x0000007f0000 : "rootfs"
[ 1.130000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.150000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000
[ 1.160000] 0x000000300000-0x0000007f0000 : "rootfs_data"
[ 1.170000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.180000] libphy: Fixed MDIO Bus: probed
[ 1.190000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.200000] GPIO_WDT: failed to register misc device
[ 1.200000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.210000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.880000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.880000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.900000] pps_core: LinuxPPS API ver. 1 registered
[ 5.900000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.920000] PTP clock support registered
[ 5.950000] tg3.c:v3.132 (May 21, 2013)
[ 5.950000] libphy: tg3 mdio bus: probed
[ 5.960000] b53_common: found switch: BCM5325, rev 0
[ 5.970000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.980000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 5.990000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 6.000000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.970000] tg3 0000:01:00.0 eth0: Link is down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.850000] NET: Registered protocol family 10
[ 14.870000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 14.890000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.920000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 14.930000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 14.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.020000] xt_time: kernel timezone is -0000
[ 15.070000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.070000] cfg80211: World regulatory domain updated:
[ 15.080000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.090000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.090000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.100000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.130000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 15.260000] PPP generic driver version 2.4.2
[ 15.280000] NET: Registered protocol family 24
[ 15.330000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.440000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.500000] Broadcom 43xx driver loaded [ Features: PNL ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x960 (2400) (0xBC040960)
Offset2: 0xFCC00 (1035264) (0xBC13CC00)
Header CRC: 0x77A4A09E
Calculate CRC: 0x77A4A09E
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3780 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.24 (buildroot@localhost.localdomain) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39211) ) #2 Fri Jan 10 16:04:45 EST 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29128k/32768k available (2278k kernel code, 3640k reserved, 574k data, 212k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.070000] Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.550000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.550000] PCI host bridge to bus 0000:01
[ 0.550000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.550000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.550000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.550000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.550000] NET: Registered protocol family 2
[ 0.550000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.550000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.550000] TCP: Hash tables configured (established 512 bind 512)
[ 0.550000] TCP: reno registered
[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.550000] NET: Registered protocol family 1
[ 0.560000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.560000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.560000] msgmni has been set to 56
[ 0.560000] io scheduler noop registered
[ 0.560000] io scheduler deadline registered (default)
[ 0.560000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.580000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.960000] console [ttyS0] enabled
[ 0.980000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.000000] physmap platform flash device: 02000001 at 1c000000
[ 1.000000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.010000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.020000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.020000] Amd/Fujitsu Extended Query version 1.0.
[ 1.030000] number of CFI chips: 1
[ 1.070000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.070000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.080000] 0x000000000000-0x000000040000 : "boot"
[ 1.090000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.100000] 0x00000004001c-0x000000040960 : "loader"
[ 1.100000] 0x000000040960-0x00000013cc00 : "linux"
[ 1.110000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.120000] 0x00000013cc00-0x0000007f0000 : "rootfs"
[ 1.130000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.150000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000
[ 1.160000] 0x000000300000-0x0000007f0000 : "rootfs_data"
[ 1.170000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.180000] libphy: Fixed MDIO Bus: probed
[ 1.190000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.200000] GPIO_WDT: failed to register misc device
[ 1.200000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.210000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 212K (802cb000 - 80300000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
cat: can't open '/proc/diag/model': No such file or directory
ifconfig: SIOCSIFADDR: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.890000] diag: kernel found a "Linksys WRT300N V1.1"
[ 5.890000] diag: Detected 'Linksys WRT300N V1.1'
[ 5.910000] pps_core: LinuxPPS API ver. 1 registered
[ 5.910000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 5.930000] PTP clock support registered
[ 5.950000] tg3.c:v3.132 (May 21, 2013)
[ 5.960000] libphy: tg3 mdio bus: probed
[ 5.970000] b53_common: found switch: BCM5325, rev 0
[ 5.980000] tg3 0000:01:00.0 eth0: Tigon3 [partno(none) rev 4001] (PCI:33MHz:32-bit) MAC address 00:1d:7e:1c:38:9a
[ 5.990000] tg3 0000:01:00.0 eth0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=100:1e)
[ 6.000000] tg3 0000:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 6.010000] tg3 0000:01:00.0 eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
mount_root: jffs2 is not ready - EOF marker found
[ 8.970000] tg3 0000:01:00.0 eth0: Link is down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 14.860000] NET: Registered protocol family 10
[ 14.880000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 14.900000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.930000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093
[ 14.940000] Backport generated by backports.git backports-20130802-0-gdb67a3f
[ 14.950000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 15.030000] xt_time: kernel timezone is -0000
[ 15.080000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.080000] cfg80211: World regulatory domain updated:
[ 15.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.110000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.120000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.130000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm)
[ 15.140000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 15.270000] PPP generic driver version 2.4.2
[ 15.290000] NET: Registered protocol family 24
[ 15.340000] b43-phy0: Broadcom 4321 WLAN found (core revision 11)
[ 15.450000] b43-phy0: Found PHY: Analog 5, Type 4 (N), Revision 1
[ 15.510000] Broadcom 43xx driver loaded [ Features: PNL ]
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0](Last edited by boblfoot on 10 Jan 2014, 23:23)
boblfoot: can you edit your post and put bootlog inside [code] tag, please?
boblfoot: please type "make menuconfig", enter: Target Profile and select "Broadcom SoC, all Ethernet, No WiFi". Then recompile and try again. I think it may be b43 that causes these reboots for you.
well the build without wireless still jsut reboots.
The fact is some GPIO can (doesn't have to, but can) reset your device. I can imagine 3 things touching GPIOs:
1) b53 (switch driver)
2) b43 (wireless driver)
3) diag (helper for LEDs and buttons)
We are 100% sure it's not b43 fault in this case. b53 should not do it too (with Hauke's patch), but I'm not 100% sure about that yet. diag in theory initializes much earlier (10s before the reboot), but who knows...
Just for sure, could you do additional tests, please?
1) Switch Target Profile to "Broadcom SoC, bgmac Ethernet, No WiFi" - this will disable tg3 and b53 won't init
2) Recompile and test
[if above doesn't help, then continue]
3) Enter Kernel modules → Other modules → disable "kmod-diag" (no "M" or "*" next to it, just "< >")
4) Recompile and test
If above also won't help (router still rebooting), then my last idea is that there is some hardware watchdog that believes Linux stopped working and reboots the machine. Can you provide output of "nvram show" (can be executer in CFE), please? Maybe there are some entries related to watchdog...
I'll be building and testing as you suggest this week, but in the meantime here is the boot log from DD-WRT_v24beta. I know we are talking apples versus oranges but perhaps the output will shed light. After all DD-WRT_v24beta boots correctly.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.01.12 23:14:29 =~=~=~=~=~=~=~=~=~=~=~=
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x300000 (3145728) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x9A8 (2472) (0xBC0409A8)
Offset2: 0xE4C00 (936960) (0xBC124C00)
Header CRC: 0x40076CA0
Calculate CRC: 0x40076CA0
Image 1 is OK
Try to load image 1.
Waiting for 5 seconds to upgrade ...
CMD: [load -raw -addr=0x806a1900 -max=0xf70000 :]
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: _tftpd_open(): retries=0/5
_tftpd_open(): retries=1/5
_tftpd_open(): retries=2/5
_tftpd_open(): retries=3/5
_tftpd_open(): retries=4/5
Failed.
Could not load :: Timeout occured
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3856 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
CPU ProcId is: 0x0002901a, options: 0x0000004d
Linux version 2.4.37 (root@dd-wrt) (gcc version 3.4.6 (OpenWrt-2.0)) #7581 Sat Oct 10 01:29:13 CEST 2009
Setting the PFC to its default value
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
CPU: BCM4785 rev 2 at 300 MHz
Using 150.000 MHz high precision timer.
Calibrating delay loop... 299.82 BogoMIPS
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
PCI: Initializing host
PCI: Enabling CardBus
PCI: Ignoring BAR0-1 of IDE controller 00:06.0
PCI: Fixing up bus 0
PCI: Fixing up bridge
PCI: Setting latency timer of device 01:00.0 to 64
PCI: Fixing up bus 1
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xb8000300 (irq = 2) is a 16550A
ttyS01 at 0xb8000400 (irq = 2) is a 16550A
PCI: Setting latency timer of device 01:01.0 to 64
PCI: Enabling device 01:01.0 (0004 -> 0006)
Overriding boardvendor: 0x14e4 instead of 0x14e4
Overriding boardtype: 0x46d instead of 0x4321
PPPoL2TP kernel driver, V0.13
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
Amd/Fujitsu Extended Query Table v0.0 at 0x0040
Physically mapped flash: JEDEC Device ID is 0xE2. Assuming broken CFI table.
Physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling fast programming due to code brokenness.
Flash device: 0x800000 at 0x1c000000
bootloader size: 262144
Physically mapped flash: Filesystem type: squashfs, size=0x20cd23
partition size = 2208768
Creating 5 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x00124c00-0x00340000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x007f0000-0x00800000 : "nvram"
0x00340000-0x007f0000 : "ddwrt"
sflash not supported on this router
Initializing Cryptographic API
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
ip_conntrack version 2.1 (512 buckets, 4096 max) - 336 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_random match loaded
netfilter PSD loaded - (c) astaro AG
ipt_osf: Startng OS fingerprint matching module.
ipt_IPV4OPTSSTRIP loaded
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
starting Architecture code for broadcom
Booting device: Linksys WRT300N v1.1
loading bcm57xxlsys
bcm_robo_attach: devid read succesfully via mii: 0x0
bcm_robo_attach: mii access to switch works
bcm_robo_attach: error reading devid, assuming 5325e
sh: can't create /proc/switch/eth0/reset: nonexistent directory
sh: can't create /proc/switch/eth1/reset: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/0/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/0/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/switch/eth0/vlan/1/ports: nonexistent directory
sh: can't create /proc/sys/net/ipv4/tcp_congestion_control: nonexistent directory
eth0: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
channel 6, val 20
800, 300, 6
spec 2B06
eth0: Invalid argument
eth0: Invalid argument
eth0: Operation not supported
eth0: Operation not supported
br0: Bad file descriptor
br0: Bad file descriptor
eth0: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
nbw = 20
channel 6, val 20
800, 300, 6
spec 2B06
eth0: Invalid argument
eth0: Invalid argument
eth0: Operation not supported
eth0: Operation not supported
vlan1: Setting MAC address to 00 1d 7e 1c 38 9b.
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
DD-WRT v24-sp2 mini (c) 2009 NewMedia-NET GmbH
Release: 10/10/09 (SVN revision: 13064)
ÿ
DD-WRT login: root
Password:
==========================================================
____ ___ __ ______ _____ ____ _ _
| _ \| _ \ \ \ / / _ \_ _| __ _|___ \| || |
|| | || ||____\ \ /\ / /| |_) || | \ \ / / __) | || |_
||_| ||_||_____\ V V / | _ < | | \ V / / __/|__ _|
|___/|___/ \_/\_/ |_| \_\|_| \_/ |_____| |_|
DD-WRT v24-sp2
[url]http://www.dd-wrt.com[/url]
==========================================================
Jan 1 00:00:27 login[391]: root login on 'console'
BusyBox v1.13.4 (2009-10-10 01:26:36 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
root@DD-WRT:~# ifconfig
br0 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9A
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
br0:0 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9A
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
eth0 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9C
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:99
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:6 Base address:0x4000
eth1 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:1296 (1.2 KiB)
Interrupt:5 Memory:18010000-18020000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:270 (270.0 B) TX bytes:270 (270.0 B)
vlan0 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
vlan1 Link encap:Ethernet HWaddr 00:1D:7E:1C:38:9B
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:1296 (1.2 KiB)
root@DD-WRT:~# iwconfig
-sh: iwconfig: not found
root@DD-WRT:~# lsmod
Module Size Used by
ip_nat_pptp 2560 0 (unused)
ip_conntrack_pptp 3036 1
ip_nat_proto_gre 1664 0 (unused)
ip_conntrack_proto_gre 2584 0 [ip_nat_pptp ip_conntrack_pptp]
etherip 5104 0 (unused)
bcm57xxlsys 120016 1
root@DD-WRT:~# nvram show
ses_script=
filter_dport_grp3=
wl_mac_deny=
wl0.1_radius_port=1812
wl1_wds4_hwaddr=
wl0_wds2_if=
http_redirect_port=3128
filter_dport_grp4=
wl1_txant=3
wl0_wds10_ospf=
wl1_wme=on
oet5_en=0
wan_unit=0
filter_dport_grp5=
filter=on
oet2_fragment=0
sv_localdns=0.0.0.0
filter_dport_grp6=
wl1_auth=0
wl0_net_mode=mixed
wl1_wds5_if=
wds0.1=
NC_Verbosity=2
pci/1/1/stbcpo=0
pci/1/1/pa2gw1a0=0
nvram_ver=3
filter_dport_grp7=
wds0.2=
altdns1=
pci/1/1/pa2gw1a1=0
filter_dport_grp8=
wl_txstreams=0
wl0_frameburst=off
wds0.3=
altdns2=
oet3_fragment=0
filter_dport_grp9=
wl1_net_mode=disabled
wds0.4=
altdns3=
wds_watchdog_interval_sec=1000
oet8_bridged=1
log_ipaddr=0
ddns_username_2=
wl1_wds2_ospf=
wds0.5=
zebra_log=0
oet9_pt=0
boardrev=0x10
ddns_username_3=
wl0_wds3_desc=
wl0_wds7_ospf=
wds0.6=
NC_RenewTimeout=0
oet2_shaper=0
oet4_fragment=0
ppp_passwd=
ppp_idletime=5
ddns_username_4=
wds0.7=
ddns_username_5=
wl1_wds3_ipaddr=
wds0.8=
zebra_copt=0
NC_SplashURL=
ddns_username_6=
wds0.9=
eth2_netmask=0.0.0.0
oet5_fragment=0
ddns_username_7=
oet8_shaper=0
qos_done=0
et0macaddr=00:1d:7e:1c:38:9a
bootnv_ver=2
wl0_leddc=0x640000
wl0.3_key=1
ddns_enable=0
ddns_username_8=
wl0_ipaddr=0.0.0.0
wl1_wds9_ipaddr=
NC_MaxMissedARP=5
oet6_fragment=0
oet10_shaper=0
wl0_shortslot=auto
wl0.2_radius_port=1812
ddns_conf=
skip_intel_check=0
NC_MACWhiteList=
wl1_wme_txp_vi=7 3 4 2 0
wan_get_dns=
wl0_akm=disabled
ddns_hostname_buf=
wl_maxassoc=128
oet3_rem=192.168.90.1
boot_wait=on
watchdog=5000
syslogd_rem_ip=
oet7_fragment=0
filter_web_host1=
wl_phytypes=
nas_enable=1
wl0_infra=1
filter_web_host2=
wl0.2_netmask=0.0.0.0
et0mdcport=0
fw_disable=0
filter_web_host3=
eth6_netmask=0.0.0.0
filter_web_host4=
pppoe_keepalive=0
router_name=DD-WRT
wl0_wds1_desc=
wl0_wds5_ospf=
wl0_wds1_if=
wl1_wme_txp_vo=7 3 4 2 0
pptpd_client_srvsub=
oet4_netmask=255.255.255.0
oet8_fragment=0
filter_web_host5=
wshaper_enable=0
oet4_en=0
filter_web_host6=
wl_distance=2000
wl1_frag=2346
ddns_wildcard=
wl0_wds6_enable=0
eth0_ipaddr=0.0.0.0
filter_web_host7=
wl_infra=1
wl0.2_wpa_psk=
apwatchdog_enable=0
wl1_wds4_if=
oet9_fragment=0
reset_gpio=7
ses_event=2
filter_web_host8=
l2tp_get_ip=
telnet_wanport=23
wl0_wds3_netmask=
svqos_port2bw=FULL
af_publish=1
filter_web_host9=
dhcpfwd_ip=0.0.0.0
wl0_txchain_cnt=2
pmon_ver=CFE 4.109.11.2
ppp_get_ac=
pptp_server_ip=
pptpd_forcemppe=1
radio1_on_time=111111111111111111111111
restore_defaults=0
ddns_time=
pptpd_bcrelay=1
eth6_ipaddr=0.0.0.0
oet8_pt=0
wl0_wds5_hwaddr=
pptp_use_dhcp=0
oet8_netmask=255.255.255.0
wl0_br1_netmask=255.255.255.0
wl0_bandlist=b
wl0.1_hwaddr=02:1D:7E:1C:38:9D
wl0.1_key=1
wl0.3_radius_port=1812
wl0.3_radius_key=
wshaper_downlink=0
ppp_username=
wl0_wds10_hwaddr=
pptpd_client_srvip=
oet9_id=1
filter_port=
wan_lease=0
wl0_nctrlsb=lower
wl0_wme_sta_be=15 1023 3 0 0 off
wl0.3_auth_mode=disabled
ddns_enable_buf=
wl_wme_apsd=on
eth10_bridged=1
oet1_rem=192.168.90.1
oet3_mssfix=0
filter_ip_grp1=
http_wanport=8080
wl0.2_ssid=
ddns_hostname=
wl0_wds7_netmask=
wl0_wds3_ospf=
ip_conntrack_tcp_timeouts=3600
lan_gateway=0.0.0.0
filter_ip_grp2=
wl0_ifname=eth0
filter_ip_grp3=
lan_domain=
filter_ip_grp4=
dr_lan_rx=0
wl1_wds10_ipaddr=
pci/1/1/ag0=2
timer_interval=3600
filter_ip_grp5=
wl0_wds4_ipaddr=
wl1_wds6_enable=0
wl0_wme_sta_bk=15 1023 7 0 0 off
oet9_mssfix=0
reconnect_enable=0
af_city=
pci/1/1/ag1=2
filter_ip_grp6=
hs_html=
log_accepted=0
pptpd_client_srvsec=mppe required
pci/1/1/ag2=2
filter_rule1=
filter_ip_grp7=
pppoe_ac=
wshaper_uplink=0
pptpd_client_ipparam=
wl0_rxstreams=2
ses_button=0
filter_rule2=
filter_ip_grp8=
ipsec_pass=1
hb_server_ip=
vlan0ports=1 2 3 4 5*
ses_enable=1
filter_rule3=
filter_ip_grp9=
rflow_enable=0
pptpd_radserver=0.0.0.0
wl0_wds0_if=
vlan0_bridged=1
expert_mode=1
filter_rule4=
wl0.2_key1=
schedule_minutes=0
oet3_en=0
oet9_ip=1.2.3.4
filter_rule5=
wl0.2_key2=
wl1_txpwr=71
wl1_wds5_hwaddr=
wl1_wds4_netmask=
port5vlans=0 1 16
filter_rule6=
filter_ip_grp10=
wl0.2_key3=
wl0_mrate=0
wl1_wds3_if=
wan_gateway=0.0.0.0
filter_rule7=
wl0_mode=ap
wl0.2_key4=
wol_passwd=
filter_rule8=
dhcp_start=100
pptpd_radpass=
wl0_wds1_ospf=
filter_rule9=
wl0_ap_isolate=0
pptpd_enable=0
oet7_pt=0
filter_services_1=
wl_mrate=0
svqos_port4prio=10
dist_type=mini
ddns_force=10
l2tp_server_ip=
wshaper_nopriohostsrc=
NC_DocumentRoot=/www
oet3_shaper=0
dhcp_lease=1440
wl0_gmode=1
wl0_wme_no_ack=off
oet8_id=1
pci/1/1/ccdpo=0
wl1_rts=2347
wl1_wds4_ipaddr=
wl1_wds8_netmask=
af_zip=
remote_ip_any=1
wds_watchdog_ips=
eth3_bridged=1
boardtype=0x478
wl0.2_wpa_gtk_rekey=3600
oet1_bridged=1
wl_active_add_mac=0
is_default=1
dnsmasq_enable=1
oet9_shaper=0
ping_ip=
wl0_nband=2
port3vlans=0
eth10_netmask=0.0.0.0
pci/1/1/txpid2ga0=91
stats_server=
af_agree=0
pci/1/1/txpid2ga1=91
static_route=
need_commit=1
wl0_nreqd=0
sip_port=5060
lan_netmask=255.255.255.0
wl0.3_bridged=1
wl0.1_crypto=off
wl0_security_mode=disabled
radvd_conf=
pptpd_client_mtu=1450
dmz_enable=0
wl0_wds1_enable=0
eth7_bridged=1
http_source_network=0.0.0.0
http_username=bJ/GddyoJuiU2
wl0_ssid=dd-wrt
wl0_dtim=1
wl_wme_sta_vi=7 15 2 6016 3008 off
oet5_bridged=1
wifi_display=wl0
port_trigger=
wl1_wds9_desc=
apd_enable=0
oet2_en=0
oet8_ip=1.2.3.4
filter_web_host10=
wl1_wds10_netmask=
wl_wme_ap_be=15 63 3 0 0 off
http_redirect_enable=0
os_date=Oct 10 2009
wl0_dfs_preism=60
wl1_wds2_if=
cron_enable=1
wl0_wds7_enable=0
svqos_port2prio=10
eth1_ipaddr=0.0.0.0
http_lanport=80
filter_mac_grp1=
wl_plcphdr=long
wl_wme_sta_vo=3 7 2 3264 1504 off
pci/1/1/txpt2g=0x36
filter_mac_grp2=
ppp_redialperiod=30
ppp_service=
wl_macmode=disabled
port1vlans=0
oet6_pt=0
pci/1/1/pa2gw0a0=0
hopdwell=1000
wan_hwname=
wan_domain=
filter_mac_grp3=
wl_wme_ap_bk=15 1023 7 0 0 off
wl1_wme_ap_be=15 63 3 0 0 off
eth7_ipaddr=0.0.0.0
oet8_comp=0
oet10_pt=0
pci/1/1/pa2gw0a1=0
lan_lease=86400
wan_netmask=0.0.0.0
filter_mac_grp4=
wl0_web_filter=0
wl_phytype=g
wl0_key1=
wl0_wds6_hwaddr=
radiooff_button=0
oet9_bridged=1
filter_mac_grp5=
pppoe_static_ip=
wl0_vlan_prio_mode=off
wl_lazywds=0
wl0_key2=
oet7_id=1
wl0.2_hwaddr=02:1D:7E:1C:38:9E
filter_mac_grp6=
wl0_key3=
wl_dfs_postism=60
ddns_wildcard_6=
wl0_txant=3
oet10_bridged=1
filter_mac_grp7=
wl0_key4=
ddns_wildcard_7=
wl1_wds10_desc=
sputnik_mjid_type=0
pptpd_client_srvsubmsk=
filter_client0=
filter_mac_grp8=
wl0_bridged=1
ddns_url=
wshaper_nopriohostdst=
filter_maclist=
filter_mac_grp9=
wl1_wds1_enable=0
wl1_wds7_desc=
wl1_wme_ap_bk=15 1023 7 0 0 off
eth3_netmask=0.0.0.0
oet4_mssfix=0
pci/1/1/boardflags=0x200
ppp_demand=0
pptp_get_ip=
pptp_pass=1
oet1_netmask=255.255.255.0
ppp_keepalive=0
wl1_bcn=100
mtu_enable=0
wl1_wds0=
wl0_br1_nat=0
wl1_wds1=
block_activex=0
wl1_wds2=
wan_ifname2=vlan1
wl0_wds5_ipaddr=
wl1_wds7_enable=0
wl1_wds3=
http_passwd=bJz7PcC1rCRJQ
wl0.1_ipaddr=0.0.0.0
sshd_forwarding=0
wl0_br1_enable=0
wl1_wds4=
block_wan=1
wl0_wds10_ipaddr=
wl1_wds5=
oet6_comp=0
lan_stp=0
wl0.3_netmask=0.0.0.0
wl1_wds6=
oet1_en=0
oet7_ip=1.2.3.4
pppoe_wan_ifname=vlan1
wl0.3_akm=disabled
wl0.3_radius_ipaddr=
wl1_wds7=
wl0_wme_ap_vi=7 15 1 6016 3008 off
eth7_netmask=0.0.0.0
router_style=elegant
wl_mode=ap
wl0.1_radius_key=
skip_amd_check=0
wl1_wds6_hwaddr=
wl1_wds8=
wl1_wds1_if=
oet5_netmask=255.255.255.0
pppd_pppifname=
wl1_wds9=
forward_spec=
wl0_closed=0
wl0_rate=0
wl0_plcphdr=long
wl0.3_wpa_psk=
l2tp_server_name=
wl1_wds5_desc=
wl1_wds9_ospf=
wl0gpio0=8
wl0_macmode=disabled
wl0_wds4_netmask=
schedule_enable=0
oet5_pt=0
pptpd_client_srvmru=1450
wl0_radioids=BCM2055
pptpd_radius=0
svqos_port1bw=FULL
wl0_wme_ap_vo=3 7 1 3264 1504 off
pci/1/1/boardvendor=0x14e4
wl0_phytype=n
wl_wme_txp_vi=7 3 4 2 0
sputnik_rereg=1
filter_tod_buf1=
wl0_lazywds=0
dr_wan_rx=0
NC_RouteOnly=0
oet6_id=1
wl0_rxchain_cnt=2
filter_tod_buf2=
block_proxy=0
wds1.10=
oet4_shaper=0
oet10_id=1
oet10_fragment=0
filter_tod_buf3=
wds1.11=
rflow_port=2055
NC_GatewayPort=5280
oet9_netmask=255.255.255.0
blink_diag_led=1
upnp_ssdp_interval=60
filter_tod_buf4=
pptpd_rip=
wl1_wds5_ipaddr=
wds1.12=
qos_type=0
oet4_comp=0
filter_tod_buf5=
wds1.13=
oet10_netmask=255.255.255.0
filter_tod_buf6=
wl0_netmask=0.0.0.0
wl0_afterburner=off
dr_lan_tx=0
wds1.14=
wl_wme_txp_vo=7 3 4 2 0
upnpcas=0
lan_hwaddr=00:1D:7E:1C:38:9A
filter_tod10=
filter_tod_buf7=
wl0_antdiv=3
apwatchdog_interval=15
wl0_wds8_netmask=
wds1.15=
wol_macs=
NC_SplashURLTimeout=21600
wan_dns=
filter_tod_buf8=
wl0.1_auth_mode=disabled
wl1_wds10_ospf=
wds1.16=
radio1_timer_enable=0
filter_tod_buf9=
wl1_wds1_netmask=
oet8_rem=192.168.90.1
pci/1/1/bw40po=0
wl0.1_akm=disabled
wl1_wds3_desc=
wl1_wds7_ospf=
wl_shortslot=auto
wl_ssid=dd-wrt
wl_dtim=1
wl0_wds8_desc=
ipv6_enable0=0
ip_conntrack_max=4096
pci/1/1/sromrev=4
wl0.2_crypto=off
wl1_frameburst=off
wl0_wpa_psk=
dhcpd_usenvram=0
log_dropped=0
forward_entries=0
wait_time=5
wl0_wds2_enable=0
oet6_ip=1.2.3.4
ppp_mppe=
pptpd_radport=1812
oet10_ip=1.2.3.4
pci/1/1/venid=0x14e4
wl1_wds0_if=
daylight_time=3
wl0.2_auth=0
wl_passphrase=
macupd_ip=0.0.0.0
dns_dnsmasq=1
dhcp_wins=wan
wl1_shortslot=auto
security_mode=disabled
wl0_wds9_if=
eth2_ipaddr=0.0.0.0
oet2_comp=0
af_address_2=
wl0_mbss=1
os_server=
filter_tod_buf10=
wl0_wds8_enable=0
wl0_wds1_hwaddr=
wl1_wds5_netmask=
upgrade_delay=300
eth0_bridged=1
pppoe_static=0
oet4_pt=0
port_swap=0
wan_proto=dhcp
hb_server_domain=
remote_mgt_ssh=0
wl1_afterburner=off
wl0_unit=0
ospfd_conf=
mmc_enable=0
eth8_ipaddr=0.0.0.0
oet5_id=1
wl0_wds7_hwaddr=
wl1_wds1_desc=
wl1_wds5_ospf=
wds0.10=
wshaper_noprioportsrc=
wl_hwaddr=
ddns_cache=
wl0_txpwr=71
wl0_wds6_desc=
wds0.11=
NC_IncludePorts=
wl0.3_hwaddr=02:1D:7E:1C:38:9F
pci/1/1/boardrev=0x4b
wds0.12=
enable_jffs2=0
pptpd_client_srvpass=
static_route_name=
wds0.13=
oet6_rem=192.168.90.1
tftpd_ipaddr=192.168.1.254
wl1_wds9_netmask=
wds0.14=
eth4_bridged=1
oet5_mssfix=0
wl0_nmode=-1
wl1_wds2_enable=0
wds0.15=
oet2_bridged=1
pci/1/1/itt2ga0=0
wl_net_mode=mixed
wl_active_mac=
ntp_enable=1
wds0.16=
pci/1/1/itt2ga1=0
enable_game=0
remote_ip=0.0.0.0 0
forward_port=
ddns_custom_5=
wl0_wds6_ipaddr=
wl1_wds8_enable=0
wl1_wds1_hwaddr=
sys_enable_jffs2=0
smtp_redirect_enable=0
NC_HomePage=http://www.dd-wrt.com
pci/1/1/pa2gw3a0=0
wl0.2_ipaddr=0.0.0.0
wshaper_dev=WAN
oet5_ip=1.2.3.4
pci/1/1/pa2gw3a1=0
pci/1/1/maxp2ga0=0
pci/1/1/maxp2ga1=0
wl_rxstreams=0
wl1_wds3_ospf=
eth8_bridged=1
squid_watchdog_interval_sec=120
filter_mac_grp10=
wl0_wds=
wl0_wds4_desc=
wl0_wds8_ospf=
oet6_bridged=1
generate_key=0
wanup=0
ppp_static_ip=
wl_rate=0
ddns_dyndnstype_6=
wl1_wds7_hwaddr=
wl0_wds8_if=
pptp_server_name=
log_level=0
block_java=0
telnetd_enable=1
wl1_wme_sta_be=15 1023 3 0 0 off
ct_modules=
ntp_server=
wl0_reg_mode=off
hs_urls=
static_leasenum=0
oet3_pt=0
wan_hwaddr=00:1D:7E:1C:38:9B
pci/1/1/boardtype=0x46d
NC_GatewayName=DD-WRT
eth0_netmask=0.0.0.0
lan_ifnames=vlan0 eth0
oet4_rem=192.168.90.1
oet4_id=1
pppoe_ifname=vlan1
wl_macmode1=disabled
sshd_dss_host_key=
remote_mgt_telnet=0
eth10_ipaddr=0.0.0.0
clone_wan_mac=0
wl0_auth=0
wl0_radius_port=1812
wl0_wme=on
wl1_wme_sta_bk=15 1023 7 0 0 off
oet5_shaper=0
smtp_source_network=0.0.0.0
wl0_radius_ipaddr=
sshd_port=22
wl1_wds6_ipaddr=
af_email=
wan_default=vlan1
pppoe_service=
cron_jobs=
wshaper_noprioportdst=
pci/1/1/boardflags2=3
wl1_wds1_ospf=
svqos_macs=
wl0_wme_sta_vi=7 15 2 6016 3008 off
pa0maxpwr=251
wl1_antdiv=3
wl0_wds2_desc=
wl0_wds6_ospf=
wl0.3_wpa_gtk_rekey=3600
eth4_netmask=0.0.0.0
schedule_weekdays=00
oet2_netmask=255.255.255.0
af_enable=0
squid_watchdog_enable=0
ddns_change=
wl1_br1_nat=0
pci/1/1/ofdm2gpo=0
wan_ifnames=vlan1
remote_management=0
pci/1/1/ledbh0=8
wl_crypto=off
wl_rateset=default
block_loopback=0
svqos_port4bw=FULL
hs_enable=
schedule_time=3600
NC_ExcludePorts=25
wl0_wme_sta_vo=3 7 2 3264 1504 off
radio0_timer_enable=0
oet4_ip=1.2.3.4
oet10_rem=192.168.90.1
pci/1/1/ledbh1=-1
wl1_ap_isolate=0
wl0.3_crypto=off
wl0_wds1_netmask=
pci/1/1/ledbh2=-1
wl0.2_key=1
wl0_wds3_enable=0
pci/1/1/ledbh3=-1
http_method=post
ppp_mru=1500
wl_wep_bit=64
svqos_svcs=
wifi_bonding=0
wl0_wds7_if=
hs_exempt=
wl1_wme_no_ack=off
eth8_netmask=0.0.0.0
lan_ipaddr=192.168.1.1
clkfreq=300
os_name=linux
upnp_internet_dis=0
lan_proto=dhcp
filter_port_grp1=
oet2_rem=192.168.90.1
oet6_netmask=255.255.255.0
pptpd_client_srvmtu=1450
vlan1hwname=et0
filter_port_grp2=
wl0_wds9_enable=0
wl0_maxassoc=128
eth3_ipaddr=0.0.0.0
oet2_pt=0
portprio_support=0
filter_port_grp3=
filter_port_grp10=
ddns_passwd_2=
wl0_wds2_hwaddr=
filter_id=1
filter_port_grp4=
wl0.3_ssid=
wl1_plcphdr=long
wl_unit=0
dr_wan_tx=0
ddns_passwd_3=
wl0_wds4_ospf=
clean_jffs2=0
trigger_entries=0
filter_port_grp5=
wl0_phytypes=n
wl0_max_unauth_users=0
ddns_passwd_4=
wol_enable=0
wl1_maxassoc=128
oet3_id=1
wl0_wep=disabled
pci/1/1/mcs2gpo0=0
filter_port_grp6=
wl0_frag=2346
wl_nmode_protection=auto
ddns_passwd_5=
wl0_wds5_netmask=
eth9_ipaddr=0.0.0.0
pci/1/1/mcs2gpo1=0
filter_port_grp7=
wl0.1_closed=0
ddns_username=
ddns_passwd_6=
syslogd_enable=0
maskmac=1
pci/1/1/mcs2gpo2=0
filter_port_grp8=
pppoe_passwd=
ddns_passwd=
ddns_passwd_7=
wl0_wds8_hwaddr=
pci/1/1/mcs2gpo3=0
filter_port_grp9=
wl0_nbw=20
wl0_distance=2000
block_ident=1
ddns_passwd_8=
pci/1/1/mcs2gpo4=0
sdram_config=0x0062
log_enable=0
ppp_ac=
hs_image=
dhcpfwd_enable=0
wl1_wme_txp_be=7 3 4 2 0
auth_dnsmasq=1
wl0_btc_mode=0
pci/1/1/mcs2gpo5=0
filter_web_url10=
wl0_wds10_if=
sip_domain=192.168.1.1
pci/1/1/mcs2gpo6=0
vlan1ports=0 5
dmz_ipaddr=0
wl0_wds1_ipaddr=
oet6_mssfix=0
pci/1/1/mcs2gpo7=0
wl_wds=
wl0.3_key1=
security_mode_last=
rc_startup=
sshd_passwd_auth=1
wl1_wds3_enable=0
schedule_hours=0
pptpd_client_enable=0
wl0.3_key2=
wl0.1_radius_ipaddr=
ddns_hostname_2=
sshd_enable=0
wl0_wds9_netmask=
wl1_wds10_if=
wol_interval=86400
wl0.3_key3=
ddns_hostname_3=
wl0.3_key4=
ddns_hostname_4=
wl1_wme_txp_bk=7 3 4 2 0
radiooff_boot_off=0
af_category=0
pci/1/1/bwduppo=0
boot_hw_ver=1.1
wl0.1_ssid=
wl0_rateset=default
ddns_hostname_5=
wl0_wds7_ipaddr=
wl0_wds2_ospf=
wl1_wds9_enable=0
wl1_wds2_netmask=
trunking=0
oet3_ip=1.2.3.4
ddns_hostname_6=
wl1_wds2_hwaddr=
wl0.3_ipaddr=0.0.0.0
ddns_hostname_7=
macupd_port=2056
wl0_wme_apsd=on
pptpd_client_srvuser=DOMAIN\\Username
wl1_web_filter=0
ddns_hostname_8=
pptpd_acctport=1813
wl0_txstreams=2
pppoe_idletime=5
wl_radauth=0
wl0_wds6_if=
wl_wme=on
pci/1/1/aa2g=7
ping_times=
wl1_wme_apsd=on
oet9_en=0
pptpd_client_nat=1
lan_ifname=br0
wan_primary=1
wl1_wds8_hwaddr=
wl_wme_ap_vi=7 15 1 6016 3008 off
fullswitch=0
oet1_pt=0
boardflags=0x110
filter_services=
wl1_wds9_if=
wandevs=vlan1
sdram_refresh=0x0000
hopseq=0
pptp_extraoptions=
wl1_wds6_netmask=
overclocking=300
dhcp_domain=wan
wl0.1_key1=
wl0_radius_override=1
pptp_reorder=1
eth1_bridged=1
oet2_id=1
wl_auth=0
wl0.1_key2=
wl1_wds1_ipaddr=
port4vlans=0
sdram_ncdl=0x506
wl0.1_key3=
wl_wep_last=
samba_mount=0
vlans=0
sputnik_done=0
wan_dial=0
wl0.1_key4=
wan_gateway_buf=0.0.0.0
wl_wme_ap_vo=3 7 1 3264 1504 off
wl1_wme_ap_vi=7 15 1 6016 3008 off
wan_vdsl=0
block_cookie=0
resetbutton_enable=1
oet6_shaper=0
warn_connlimit=500
ezc_enable=1
wl_frameburst=off
rc_firewall=
wl1_br1_enable=0
wl0_nmode_protection=auto
wl1_wds7_ipaddr=
NC_enable=0
wl0_br1_ipaddr=0.0.0.0
wl1_dtim=1
upnp_wan_proto=
wl0.1_bridged=1
eth5_bridged=1
wan_ipaddr=0.0.0.0
filter_web_url1=
dhcp_num=50
wl0.2_radius_key=
svqos_port3prio=10
smtp_redirect_destination=0.0.0.0
wl1_wme_ap_vo=3 7 1 3264 1504 off
filter_web_url2=
oet3_bridged=1
filter_web_url3=
reconnect_hours=0
filter_web_url4=
wl0_rts=2347
oet2_ip=1.2.3.4
af_country=
filter_web_url5=
zebra_conf=
ospfd_copt=0
af_ssid_name=AnchorFree WiFi
wan_wins=0.0.0.0
filter_web_url6=
wl_ifname=
wl1_wds10_enable=0
port2vlans=0
fon_enable=0
filter_web_url7=
http_enable=1
wl_wep=disabled
ntp_mode=auto
ipv6_enable=0
wl0_wds4_enable=0
wds1.1=
oet9_comp=0
pci/1/1/pa2gw2a0=0
filter_web_url8=
l2tp_pass=1
wl0_radauth=0
wl0_wds5_if=
wds1.2=
pci/1/1/pa2gw2a1=0
diag_gpio=1
os_version=4.150.10.5
filter_web_url9=
pppoe_username=
wl0.2_auth_mode=disabled
ddns_dyndnstype=
wds1.3=
svqos_ips=
sputnik_mode=standard
eth9_bridged=1
oet8_en=0
wl_gmode_protection=auto
l2tp_use_dhcp=0
wds1.4=
oet7_bridged=1
wl0_wpa_gtk_rekey=3600
sshd_rsa_host_key=
wl1_wds8_if=
wds1.5=
eth4_ipaddr=0.0.0.0
ppp_get_srv=
wl0_sta_retry_time=5
mac_clone_enable=0
wds1.6=
wl_frag=2346
wl0_wds3_hwaddr=
wl1_wds8_desc=
wds1.7=
oet1_id=1
wl0_key=1
wl_wep_gen=
wan_mtu=1500
wds1.8=
wds1.9=
eth1_netmask=0.0.0.0
filter_macmode=deny
mfg_wait=on
wl0.2_closed=0
wl0_wds9_hwaddr=
oet1_mssfix=0
et0phyaddr=30
console_loglevel=1
ppp_compression=0
svqos_port1prio=10
probe_blacklist=eth1
time_zone=+01
dnsmasq_options=
sshd_wanport=22
port0vlans=1
NC_LoginTimeout=86400
oet7_comp=0
wan_get_domain=
reconnect_minutes=0
wl0_wds2_ipaddr=
wl1_wds4_enable=0
oet7_mssfix=0
ttraff_enable=1
af_state=
wan_ifname=vlan1
wl0.1_netmask=0.0.0.0
upnp_max_age=180
radvd_enable=0
sshd_authorized_keys=
wl_wme_sta_be=15 1023 3 0 0 off
eth5_netmask=0.0.0.0
squid_proxy_server_port=3128
wl_radioids=
oet1_ip=1.2.3.4
oet3_netmask=255.255.255.0
landevs=vlan0 wl0
wan_hostname=
wl0_dfs_postism=60
wl1_rate=0
wl1_wds6_desc=
af_ssid=0
gozila_action=0
boot_hw_model=WRT300N
ppp_mtu=1500
wl_corerev=
wl0_radio=1
wl0_wds8_ipaddr=
DD_BOARD=Linksys WRT300N v1.1
wl0.1_wpa_psk=
info_passwd=0
wl1_wds3_hwaddr=
wl0_wds0=
zebra_enable=1
sv_restore_defaults=0
af_address=
wl0_wds2_netmask=
wl0_wds1=
wl0_wds4_if=
svqos_port3bw=FULL
wl0_bcn=100
wl0_wds2=
manual_boot_nv=0
wl_wme_sta_bk=15 1023 7 0 0 off
oet7_en=0
oet10_comp=0
pptpd_auth=
wl0_wds3=
wl0_hwaddr=00:1D:7E:1C:38:9C
dtag_vlan8=0
filter_tod1=
ppp_static=0
wl_radio=1
wl_afterburner=off
block_multicast=1
wl1_wds9_hwaddr=
wl0_wds4=
wl1_wds7_if=
macupd_interval=10
radio0_on_time=111111111111111111111111
pci/1/1/ccode=
filter_tod2=
wl0_wds5=
dyn_default=0
log_rejected=0
eth9_netmask=0.0.0.0
oet5_comp=0
filter_tod3=
wl0_wds6=
oet7_netmask=255.255.255.0
ezc_version=2
filter_tod4=
wl0_wds7=
oet1_shaper=0
filter_tod5=
wl0_gmode_protection=auto
wk_mode=gateway
ddns_passwd_buf=
wl0_wds8=
oet9_rem=192.168.90.1
filter_tod6=
wl0.1_wpa_gtk_rekey=3600
wl0.2_akm=disabled
rc_shutdown=
wl1_wds2_ipaddr=
wl0_wds9=
filter_tod7=
wl0_wds6_netmask=
NC_GatewayMode=Open
sdram_init=0x0549
filter_tod8=
wl_rts=2347
wl0_radmacpassword=0
wl1_wds4_desc=
wl1_wds8_ospf=
switch_type=BCM5325
wl0_abenable=1
filter_tod9=
wl0_wds9_desc=
oet7_shaper=0
vlan0hwname=et0
lan_wins=
wl_ap_isolate=0
lan_hwnames=
wl_mac_list=
dhcpd_options=
wl1_wds8_ipaddr=
ip_conntrack_udp_timeouts=120
NC_IdleTimeout=0
dhcp_dnsmasq=1
wl1_abenable=1
dhcpd_usejffs=0
pppoe_demand=0
wds_watchdog_enable=0
wl_wme_no_ack=off
static_leases=
wl0.3_auth=0
local_dns=0
filter_dport_grp10=
wl1_gmode_protection=auto
wl0_radius_key=
wl0_wds10_desc=
oet3_comp=0
ddns_username_buf=
wl0_wds10_netmask=
wl0_wme_ap_be=15 63 3 0 0 off
wl0_corerev=11
wl0_nmcsidx=-1
wl0_lazy_wds=
cardbus=1
refresh_time=3
wl1_rateset=default
wl1_wds3_netmask=
pci/1/1/regrev=0
wl0_channel=6
wl0_wds3_if=
pptp_encrypt=0
wl0_wds5_enable=0
oet6_en=0
ddns_wan_ip=0
wl1_wds2_desc=
wl1_wds6_ospf=
NC_ForcedRedirect=0
oet10_en=0
pci/1/1/devid=0x4329
upnp_enable=0
dr_setting=0
wl0_wds10_enable=0
wl0_wds7_desc=
wl1_wds6_if=
schedule_hour_time=1
wl0_wme_ap_bk=15 1023 7 0 0 off
oet7_rem=192.168.90.1
hs_redirect=
wl_wme_txp_be=7 3 4 2 0
http_redirect_destination=0.0.0.0
wl1_wds10_hwaddr=
eth5_ipaddr=0.0.0.0
pci/1/1/macaddr=00:88:88:88:00:2a
pptpd_lip=
wl0_wds4_hwaddr=
wol_hostname=
wl1_wme_sta_vi=7 15 2 6016 3008 off
dhcpc_vendorclass=
filter_rule10=
wl0.1_auth=0
wl_dfs_preism=60
wl1_wds7_netmask=
rflow_if=br0
forwardspec_entries=0
eth2_bridged=1
oet1_comp=0
wl0_auth_mode=disabled
def_whwaddr=00:00:00:00:00:00
NC_AllowedWebHosts=
wl_wme_txp_bk=7 3 4 2 0
boot_ver=v4.4
wl0.3_closed=0
status_auth=1
dhcpc_requestip=
oet2_mssfix=0
autofw_port0=
wl1_wme_sta_vo=3 7 2 3264 1504 off
pci/1/1/cck2gpo=0
boardnum=42
wl0_crypto=off
language=english
warn_enabled=0
def_hwaddr=00:00:00:00:00:00
wl1_wds=
wl_bcn=100
wl1_wds4_ospf=
oet8_mssfix=0
wl0.2_bridged=1
wl_reg_mode=off
wl_wep_buf=
macupd_enable=0
wl0_wds3_ipaddr=
wl0_wds5_desc=
wl0_wds9_ospf=
wl1_wds5_enable=0
mmc_enable0=0
eth6_bridged=1
oet10_mssfix=0
upnp_config=1
rflow_ip=0.0.0.0
oet4_bridged=1
filter_dport_grp1=
wl0.2_radius_ipaddr=
filter_dport_grp2=
rc_custom=
wl0_wds9_ipaddr=
pptpd_client_mru=1450
oet1_fragment=0
oet5_rem=192.168.90.1
size: 20203 bytes (12565 left)
root@DD-WRT:~# uname -a
Linux DD-WRT 2.4.37 #7581 Sat Oct 10 01:29:13 CEST 2009 mips unknown
root@DD-WRT:~# ls /dev
[1;35mconsole[0m [1;35mkmem[0m [1;34mmtdblock[0m [1;35mport[0m [1;34mpty[0m [1;35mtty[0m
[1;34mcua[0m [1;35mmem[0m [1;34mnet[0m [1;35mppp[0m [1;35mrandom[0m [1;35murandom[0m
[1;35mfull[0m [1;34mmisc[0m [1;35mnull[0m [1;35mptmx[0m [1;36mroot[0m [1;35mzero[0m
[1;34mgpio[0m [1;34mmtd[0m [1;35mnvram[0m [1;34mpts[0m [1;34mtts[0m
root@DD-WRT:~# boblfoot wrote:
I'll be building and testing as you suggest this week, but in the meantime here is the boot log from DD-WRT_v24beta. I know we are talking apples versus oranges but perhaps the output will shed light.
Nothing at all.
Built an image with no wifi and such as suggested and it boots but ethernet will not connect
And this is the bootup terminal output
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.04.12 23:10:31 =~=~=~=~=~=~=~=~=~=~=~=
Start to blink diag led ...
CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Feb 27 19:35:53 CST 2007 (root@localhost.localdomain)
Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
Initializing Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x02)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x471f (ethernet network, rev 0x02)
PCI bus 0 slot 2/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x02)
PCI bus 0 slot 2/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x02)
PCI bus 0 slot 3/0: vendor 0x14e4 product 0x471b (USB serial bus, rev 0x02)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x0804 (PCI bridge, rev 0x02)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0816 (MIPS processor, rev 0x02)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x471d (IDE mass storage, rev 0x02)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x4718 (network/computing crypto, rev 0x02)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080f (RAM memory, rev 0x02)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x471e (class 0xfe, subclass 0x00, rev 0x02)
Initializing Devices.
No DPN
This is a Parallel Flash
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 0004001B (28)
os #02 0004001C -> 007F7FFF (8093668)
nvram #03 007F8000 -> 007FFFFF (32768)
Partition information:
boot #00 00000000 -> 0003FFFF (262144)
trx #01 00040000 -> 007F7FFF (8093696)
nvram #02 007F8000 -> 007FFFFF (32768)
Reset switch via GPIO 8 ...
PCI bus 0 slot 1/0: pci_map_mem: attempt to map 64-bit region tag=0x800 @ addr=18010004
PCI bus 0 slot 1/0: pci_map_mem: addr=0x18010004 pa=0x18010000
ge0: BCM5750 Ethernet at 0x18010000
CPU type 0x2901A: 300MHz
Total memory: 32768 KBytes
Total memory used by CFE: 0x80600000 - 0x806A1900 (661760)
Initialized Data: 0x80636C40 - 0x80639BE0 (12192)
BSS Area: 0x80639BE0 - 0x8063B900 (7456)
Local Heap: 0x8063B900 - 0x8069F900 (409600)
Stack Area: 0x8069F900 - 0x806A1900 (8192)
Text (code) segment: 0x80600000 - 0x80636C40 (224320)
Boot area (physical): 0x006A2000 - 0x006E2000
Relocation Factor: I:00000000 - D:00000000
Boot version: v4.4
The boot is CFE
mac_init(): Find mac [00:1d:7e:1c:38:9a] in location 0
Nothing...
CMD: [ifconfig eth0 -addr=192.168.1.1 -mask=255.255.255.0]
eth0: Link speed: 100BaseT FDX
Device eth0: hwaddr 00-1D-7E-1C-38-9A, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
CMD: [go;]
Check CRC of image1
Len: 0x10000 (65536) (0xBC040000)
Offset0: 0x1C (28) (0xBC04001C)
Offset1: 0x90C (2316) (0xBC04090C)
Offset2: 0x100000 (1048576) (0xBC140000)
Header CRC: 0x8612BDF6
Calculate CRC: 0x8612BDF6
Image 1 is OK
Try to load image 1.
CMD: [boot -raw -z -addr=0x80001000 -max=0xf70000 flash0.os:]
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3712 bytes read
Entry at 0x80001000
Closing network.
eth0: cannot clear 1400/00000002
Starting program at 0x80001000
[ 0.000000] Linux version 3.10.36 (buildroot@localhost.localdomain) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40469) ) #1 Sat Apr 12 14:07:32 EDT 2014
[ 0.000000] CPU revision is: 0002901a (Broadcom BMIPS3300)
[ 0.000000] bcm47xx: using ssb bus
[ 0.000000] ssb: Found chip with id 0x4785, rev 0x02 and package 0x0C
[ 0.000000] Unsupported SPROM revision 0 detected. Will extract v1
[ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[ 0.000000] MIPS: machine is Linksys WRT300N V1.1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 29128k/32768k available (2293k kernel code, 3640k reserved, 575k data, 196k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.060000] Calibrating delay loop... 298.59 BogoMIPS (lpj=1492992)
[ 0.060000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.070000] NET: Registered protocol family 16
[ 0.090000] bio: create slab <bio-0> at 0
[ 0.100000] Switching to clocksource MIPS
[ 0.400000] PCI host bridge to bus 0000:00
[ 0.400000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
[ 0.400000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff]
[ 0.400000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.400000] ssb: PCI: Fixing up bridge 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing up device 0000:00:00.0
[ 0.400000] ssb: PCI: Fixing latency timer of device 0000:00:00.0 to 168
[ 0.410000] pci 0000:00:01.0: BAR 0: assigned [mem 0x40000000-0x40003fff]
[ 0.410000] ssb: PCI: Fixing up device 0000:00:01.0
[ 0.450000] ssb: Found chip with id 0x4321, rev 0x01 and package 0x01
[ 0.500000] can not parse nvram name pci/1/1/ledbh1(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh2(null) with value -1 got -22
[ 0.500000] can not parse nvram name pci/1/1/ledbh3(null) with value -1 got -22
[ 0.560000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.560000] PCI host bridge to bus 0000:01
[ 0.560000] pci_bus 0000:01: root bus resource [mem 0x18010000-0x1801ffff]
[ 0.560000] pci_bus 0000:01: root bus resource [io 0x0800-0x08ff]
[ 0.560000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.560000] pci 0000:01:00.0: BAR 0: assigned [mem 0x18010000-0x1801ffff 64bit]
[ 0.560000] NET: Registered protocol family 2
[ 0.560000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.560000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.560000] TCP: Hash tables configured (established 512 bind 512)
[ 0.560000] TCP: reno registered
[ 0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.560000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.560000] NET: Registered protocol family 1
[ 0.570000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.570000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.570000] msgmni has been set to 56
[ 0.570000] io scheduler noop registered
[ 0.570000] io scheduler deadline registered (default)
[ 0.570000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.600000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A
[ 0.970000] console [ttyS0] enabled
[ 1.000000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 2) is a U6_16550A
[ 1.010000] physmap platform flash device: 02000001 at 1c000000
[ 1.010000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000ec Chip ID 0x0022e2
[ 1.030000] Amd/Fujitsu Extended Query Table at 0x0040
[ 1.030000] Fixing Samsung's Amd/Fujitsu Extended Query version to 1.0
[ 1.040000] Amd/Fujitsu Extended Query version 1.0.
[ 1.040000] number of CFI chips: 1
[ 1.080000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0
[ 1.090000] Creating 6 MTD partitions on "physmap-flash.0":
[ 1.090000] 0x000000000000-0x000000040000 : "boot"
[ 1.100000] 0x000000040000-0x0000007f0000 : "firmware"
[ 1.110000] 0x00000004001c-0x00000004090c : "loader"
[ 1.120000] 0x00000004090c-0x000000140000 : "linux"
[ 1.120000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 1.140000] 0x000000140000-0x0000007f0000 : "rootfs"
[ 1.150000] mtd: device 4 (rootfs) set to be root filesystem
[ 1.150000] mtd: partition "rootfs_data" created automatically, ofs=0x270000, len=0x580000
[ 1.160000] 0x000000270000-0x0000007f0000 : "rootfs_data"
[ 1.170000] 0x0000007f0000-0x000000800000 : "nvram"
[ 1.180000] libphy: Fixed MDIO Bus: probed
[ 1.190000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[ 1.200000] GPIO_WDT: failed to register misc device
[ 1.210000] TCP: cubic registered
[ 1.210000] NET: Registered protocol family 17
[ 1.210000] 8021q: 802.1Q VLAN Support v1.8
[ 1.230000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 1.240000] Freeing unused kernel memory: 196K (802cf000 - 80300000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
[ 4.370000] bgmac: Broadcom 47xx GBit MAC driver loaded
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
jffs2 is ready
[ 13.440000] jffs2: notice: (217) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
switching to jffs2
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 16.730000] NET: Registered protocol family 10
[ 16.750000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 16.770000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 16.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.890000] xt_time: kernel timezone is -0000
[ 16.910000] PPP generic driver version 2.4.2
[ 16.920000] NET: Registered protocol family 24
procd: - init complete -
BusyBox v1.19.4 (2014-04-12 13:56:16 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r40469)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# here is the config pared down for the post above.
#
# Automatically generated file; DO NOT EDIT.
# OpenWrt Configuration
#
CONFIG_MODULES=y
CONFIG_HAVE_DOT_CONFIG=y
CONFIG_TARGET_brcm47xx=y
CONFIG_TARGET_brcm47xx_Broadcom-bgmac-none=y
CONFIG_TARGET_BOARD="brcm47xx"
CONFIG_TARGET_ARCH_PACKAGES="brcm47xx"
CONFIG_DEFAULT_TARGET_OPTIMIZATION="-Os -pipe -mno-branch-likely -mips32 -mtune=mips32"
CONFIG_CPU_TYPE="mips32"
CONFIG_LINUX_3_10=y
CONFIG_DEFAULT_base-files=y
CONFIG_DEFAULT_busybox=y
CONFIG_DEFAULT_dnsmasq=y
CONFIG_DEFAULT_dropbear=y
CONFIG_DEFAULT_firewall=y
CONFIG_DEFAULT_fstools=y
CONFIG_DEFAULT_ip6tables=y
CONFIG_DEFAULT_iptables=y
CONFIG_DEFAULT_iwinfo=y
CONFIG_DEFAULT_kmod-bgmac=y
CONFIG_DEFAULT_kmod-gpio-button-hotplug=y
CONFIG_DEFAULT_kmod-ipt-nathelper=y
CONFIG_DEFAULT_kmod-leds-gpio=y
CONFIG_DEFAULT_kmod-ledtrig-default-on=y
CONFIG_DEFAULT_kmod-ledtrig-netdev=y
CONFIG_DEFAULT_kmod-ledtrig-timer=y
CONFIG_DEFAULT_libc=y
CONFIG_DEFAULT_libgcc=y
CONFIG_DEFAULT_mtd=y
CONFIG_DEFAULT_netifd=y
CONFIG_DEFAULT_nvram=y
CONFIG_DEFAULT_odhcp6c=y
CONFIG_DEFAULT_odhcpd=y
CONFIG_DEFAULT_opkg=y
CONFIG_DEFAULT_ppp=y
CONFIG_DEFAULT_ppp-mod-pppoe=y
CONFIG_DEFAULT_swconfig=y
CONFIG_DEFAULT_uci=y
CONFIG_AUDIO_SUPPORT=y
CONFIG_GPIO_SUPPORT=y
CONFIG_PCI_SUPPORT=y
CONFIG_PCMCIA_SUPPORT=y
CONFIG_USB_SUPPORT=y
CONFIG_USES_SQUASHFS=y
CONFIG_mipsel=y
CONFIG_ARCH="mipsel"
#
# Target Images
#
CONFIG_EXTERNAL_CPIO=""
#
# Root filesystem images
#
CONFIG_TARGET_ROOTFS_SQUASHFS=y
CONFIG_TARGET_UBIFS_FREE_SPACE_FIXUP=y
CONFIG_TARGET_UBIFS_JOURNAL_SIZE=""
#
# Image Options
#
CONFIG_TARGET_ROOTFS_INCLUDE_UIMAGE=y
CONFIG_TARGET_ROOTFS_INCLUDE_ZIMAGE=y
CONFIG_TARGET_ROOTFS_INCLUDE_FIT=y
#
# Global build settings
#
# CONFIG_ALL is not set
#
# General build options
#
CONFIG_BUILD_PATENTED=y
CONFIG_SHADOW_PASSWORDS=y
#
# Kernel build options
#
CONFIG_KERNEL_PRINTK=y
CONFIG_KERNEL_CRASHLOG=y
CONFIG_KERNEL_SWAP=y
CONFIG_KERNEL_DEBUG_FS=y
CONFIG_KERNEL_KALLSYMS=y
CONFIG_KERNEL_DEBUG_KERNEL=y
CONFIG_KERNEL_DEBUG_INFO=y
CONFIG_KERNEL_MAGIC_SYSRQ=y
CONFIG_KERNEL_COREDUMP=y
CONFIG_KERNEL_ELF_CORE=y
CONFIG_KERNEL_PRINTK_TIME=y
#
# Package build options
#
# CONFIG_DEBUG is not set
CONFIG_IPV6=y
CONFIG_PKG_BUILD_PARALLEL=y
CONFIG_PKG_BUILD_USE_JOBSERVER=y
#
# Stripping options
#
CONFIG_USE_SSTRIP=y
CONFIG_USE_UCLIBCXX=y
CONFIG_BINARY_FOLDER=""
CONFIG_DOWNLOAD_FOLDER=""
CONFIG_LOCALMIRROR=""
CONFIG_AUTOREBUILD=y
CONFIG_BUILD_SUFFIX=""
CONFIG_TARGET_ROOTFS_DIR=""
CONFIG_EXTERNAL_KERNEL_TREE=""
CONFIG_KERNEL_GIT_CLONE_URI=""
CONFIG_KERNEL_GIT_LOCAL_REPOSITORY=""
CONFIG_EXTRA_OPTIMIZATION="-fno-caller-saves"
CONFIG_TARGET_OPTIMIZATION="-Os -pipe -mno-branch-likely -mips32 -mtune=mips32"
CONFIG_SOFT_FLOAT=y
CONFIG_EXTRA_BINUTILS_CONFIG_OPTIONS=""
CONFIG_BINUTILS_VERSION="2.22"
CONFIG_EXTRA_GCC_CONFIG_OPTIONS=""
CONFIG_GDB=y
CONFIG_USE_UCLIBC=y
CONFIG_GCC_VERSION_4_8_LINARO=y
CONFIG_GCC_VERSION="4.8-linaro"
CONFIG_GCC_VERSION_4_8=y
CONFIG_UCLIBC_VERSION="0.9.33.2"
CONFIG_UCLIBC_VERSION_0_9_33=y
CONFIG_LIBC="uClibc"
CONFIG_LIBC_VERSION="0.9.33.2"
CONFIG_TARGET_SUFFIX="uclibc"
CONFIG_TARGET_PREINIT_SUPPRESS_STDERR=y
CONFIG_TARGET_PREINIT_TIMEOUT=2
CONFIG_TARGET_PREINIT_IFNAME=""
CONFIG_TARGET_PREINIT_IP="192.168.1.1"
CONFIG_TARGET_PREINIT_NETMASK="255.255.255.0"
CONFIG_TARGET_PREINIT_BROADCAST="192.168.1.255"
CONFIG_TARGET_INIT_PATH="/bin:/sbin:/usr/bin:/usr/sbin"
CONFIG_TARGET_INIT_ENV=""
CONFIG_TARGET_INIT_CMD="/sbin/init"
CONFIG_TARGET_INIT_SUPPRESS_STDERR=y
CONFIG_OPKGSMIME_PASSPHRASE=y
#
# Package features
#
CONFIG_FEATURE_drawing-backend_DirectFB=y
#
# Base system
#
CONFIG_PACKAGE_base-files=y
CONFIG_PACKAGE_busybox=y
CONFIG_BUSYBOX_DEFAULT_HAVE_DOT_CONFIG=y
CONFIG_BUSYBOX_DEFAULT_INCLUDE_SUSv2=y
CONFIG_BUSYBOX_DEFAULT_PLATFORM_LINUX=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_BUFFERS_GO_ON_STACK=y
CONFIG_BUSYBOX_DEFAULT_SHOW_USAGE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VERBOSE_USAGE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_COMPRESS_USAGE=y
CONFIG_BUSYBOX_DEFAULT_SUBST_WCHAR=0
CONFIG_BUSYBOX_DEFAULT_LAST_SUPPORTED_WCHAR=0
CONFIG_BUSYBOX_DEFAULT_LONG_OPTS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DEVPTS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PIDFILE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_SUID=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PREFER_APPLETS=y
CONFIG_BUSYBOX_DEFAULT_BUSYBOX_EXEC_PATH="/proc/self/exe"
CONFIG_BUSYBOX_DEFAULT_FEATURE_SYSLOG=y
CONFIG_BUSYBOX_DEFAULT_LFS=y
CONFIG_BUSYBOX_DEFAULT_CROSS_COMPILER_PREFIX=""
CONFIG_BUSYBOX_DEFAULT_EXTRA_CFLAGS=""
CONFIG_BUSYBOX_DEFAULT_NO_DEBUG_LIB=y
CONFIG_BUSYBOX_DEFAULT_INSTALL_APPLET_SYMLINKS=y
CONFIG_BUSYBOX_DEFAULT_PREFIX="./_install"
CONFIG_BUSYBOX_DEFAULT_PASSWORD_MINLEN=6
CONFIG_BUSYBOX_DEFAULT_MD5_SIZE_VS_SPEED=2
CONFIG_BUSYBOX_DEFAULT_FEATURE_FAST_TOP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_EDITING=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_EDITING_MAX_LEN=512
CONFIG_BUSYBOX_DEFAULT_FEATURE_EDITING_HISTORY=256
CONFIG_BUSYBOX_DEFAULT_FEATURE_TAB_COMPLETION=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_EDITING_FANCY_PROMPT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_NON_POSIX_CP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_COPYBUF_KB=4
CONFIG_BUSYBOX_DEFAULT_IOCTL_HEX2STR_ERROR=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_SEAMLESS_GZ=y
CONFIG_BUSYBOX_DEFAULT_BUNZIP2=y
CONFIG_BUSYBOX_DEFAULT_GUNZIP=y
CONFIG_BUSYBOX_DEFAULT_GZIP=y
CONFIG_BUSYBOX_DEFAULT_TAR=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TAR_CREATE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TAR_FROM=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TAR_GNU_EXTENSIONS=y
CONFIG_BUSYBOX_DEFAULT_BASENAME=y
CONFIG_BUSYBOX_DEFAULT_CAT=y
CONFIG_BUSYBOX_DEFAULT_DATE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DATE_ISOFMT=y
CONFIG_BUSYBOX_DEFAULT_ID=y
CONFIG_BUSYBOX_DEFAULT_TEST=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TEST_64=y
CONFIG_BUSYBOX_DEFAULT_TOUCH=y
CONFIG_BUSYBOX_DEFAULT_TR=y
CONFIG_BUSYBOX_DEFAULT_CHGRP=y
CONFIG_BUSYBOX_DEFAULT_CHMOD=y
CONFIG_BUSYBOX_DEFAULT_CHOWN=y
CONFIG_BUSYBOX_DEFAULT_CHROOT=y
CONFIG_BUSYBOX_DEFAULT_CP=y
CONFIG_BUSYBOX_DEFAULT_CUT=y
CONFIG_BUSYBOX_DEFAULT_DD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DD_SIGNAL_HANDLING=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DD_IBS_OBS=y
CONFIG_BUSYBOX_DEFAULT_DF=y
CONFIG_BUSYBOX_DEFAULT_DIRNAME=y
CONFIG_BUSYBOX_DEFAULT_DU=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DU_DEFAULT_BLOCKSIZE_1K=y
CONFIG_BUSYBOX_DEFAULT_ECHO=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FANCY_ECHO=y
CONFIG_BUSYBOX_DEFAULT_ENV=y
CONFIG_BUSYBOX_DEFAULT_EXPR=y
CONFIG_BUSYBOX_DEFAULT_EXPR_MATH_SUPPORT_64=y
CONFIG_BUSYBOX_DEFAULT_FALSE=y
CONFIG_BUSYBOX_DEFAULT_FSYNC=y
CONFIG_BUSYBOX_DEFAULT_HEAD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FANCY_HEAD=y
CONFIG_BUSYBOX_DEFAULT_HOSTID=y
CONFIG_BUSYBOX_DEFAULT_LN=y
CONFIG_BUSYBOX_DEFAULT_LS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_FILETYPES=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_FOLLOWLINKS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_RECURSIVE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_SORTFILES=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_TIMESTAMPS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_USERNAME=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_COLOR=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LS_COLOR_IS_DEFAULT=y
CONFIG_BUSYBOX_DEFAULT_MD5SUM=y
CONFIG_BUSYBOX_DEFAULT_MKDIR=y
CONFIG_BUSYBOX_DEFAULT_MKFIFO=y
CONFIG_BUSYBOX_DEFAULT_MKNOD=y
CONFIG_BUSYBOX_DEFAULT_MV=y
CONFIG_BUSYBOX_DEFAULT_NICE=y
CONFIG_BUSYBOX_DEFAULT_PRINTF=y
CONFIG_BUSYBOX_DEFAULT_PWD=y
CONFIG_BUSYBOX_DEFAULT_READLINK=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_READLINK_FOLLOW=y
CONFIG_BUSYBOX_DEFAULT_RM=y
CONFIG_BUSYBOX_DEFAULT_RMDIR=y
CONFIG_BUSYBOX_DEFAULT_SEQ=y
CONFIG_BUSYBOX_DEFAULT_SLEEP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FANCY_SLEEP=y
CONFIG_BUSYBOX_DEFAULT_SORT=y
CONFIG_BUSYBOX_DEFAULT_SYNC=y
CONFIG_BUSYBOX_DEFAULT_TAIL=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FANCY_TAIL=y
CONFIG_BUSYBOX_DEFAULT_TEE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TEE_USE_BLOCK_IO=y
CONFIG_BUSYBOX_DEFAULT_TRUE=y
CONFIG_BUSYBOX_DEFAULT_UNAME=y
CONFIG_BUSYBOX_DEFAULT_UNIQ=y
CONFIG_BUSYBOX_DEFAULT_WC=y
CONFIG_BUSYBOX_DEFAULT_YES=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PRESERVE_HARDLINKS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_AUTOWIDTH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_HUMAN_READABLE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MD5_SHA1_SUM_CHECK=y
CONFIG_BUSYBOX_DEFAULT_CLEAR=y
CONFIG_BUSYBOX_DEFAULT_RESET=y
CONFIG_BUSYBOX_DEFAULT_DEFAULT_SETFONT_DIR=""
CONFIG_BUSYBOX_DEFAULT_MKTEMP=y
CONFIG_BUSYBOX_DEFAULT_START_STOP_DAEMON=y
CONFIG_BUSYBOX_DEFAULT_WHICH=y
CONFIG_BUSYBOX_DEFAULT_VI=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_MAX_LEN=1024
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_COLON=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_YANKMARK=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_SEARCH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_USE_SIGNALS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_DOT_CMD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_READONLY=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_SETOPTS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_SET=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_WIN_RESIZE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_ASK_TERMINAL=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_VI_OPTIMIZE_CURSOR=y
CONFIG_BUSYBOX_DEFAULT_AWK=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_AWK_LIBM=y
CONFIG_BUSYBOX_DEFAULT_CMP=y
CONFIG_BUSYBOX_DEFAULT_SED=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_ALLOW_EXEC=y
CONFIG_BUSYBOX_DEFAULT_FIND=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_PRINT0=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_PERM=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_TYPE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_XDEV=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_MAXDEPTH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_EXEC=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_USER=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_GROUP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_NOT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_DEPTH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_PAREN=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_SIZE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_PRUNE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_PATH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FIND_REGEX=y
CONFIG_BUSYBOX_DEFAULT_GREP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_GREP_EGREP_ALIAS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_GREP_FGREP_ALIAS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_GREP_CONTEXT=y
CONFIG_BUSYBOX_DEFAULT_XARGS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_XARGS_SUPPORT_CONFIRMATION=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_XARGS_SUPPORT_QUOTES=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_XARGS_SUPPORT_TERMOPT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_XARGS_SUPPORT_ZERO_TERM=y
CONFIG_BUSYBOX_DEFAULT_HALT=y
CONFIG_BUSYBOX_DEFAULT_TELINIT_PATH=""
CONFIG_BUSYBOX_DEFAULT_FEATURE_KILL_DELAY=0
CONFIG_BUSYBOX_DEFAULT_INIT_TERMINAL_TYPE=""
CONFIG_BUSYBOX_DEFAULT_FEATURE_SHADOWPASSWDS=y
CONFIG_BUSYBOX_DEFAULT_FIRST_SYSTEM_ID=0
CONFIG_BUSYBOX_DEFAULT_LAST_SYSTEM_ID=0
CONFIG_BUSYBOX_DEFAULT_PASSWD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PASSWD_WEAK_CHECK=y
CONFIG_BUSYBOX_DEFAULT_DEFAULT_MODULES_DIR=""
CONFIG_BUSYBOX_DEFAULT_DEFAULT_DEPMOD_FILE=""
CONFIG_BUSYBOX_DEFAULT_DMESG=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_DMESG_PRETTY=y
CONFIG_BUSYBOX_DEFAULT_HEXDUMP=y
CONFIG_BUSYBOX_DEFAULT_HWCLOCK=y
CONFIG_BUSYBOX_DEFAULT_MKSWAP=y
CONFIG_BUSYBOX_DEFAULT_MOUNT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MOUNT_HELPERS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MOUNT_CIFS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MOUNT_FLAGS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MOUNT_FSTAB=y
CONFIG_BUSYBOX_DEFAULT_PIVOT_ROOT=y
CONFIG_BUSYBOX_DEFAULT_SWITCH_ROOT=y
CONFIG_BUSYBOX_DEFAULT_UMOUNT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_UMOUNT_ALL=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MOUNT_LOOP=y
CONFIG_BUSYBOX_DEFAULT_LESS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_LESS_MAXLINES=9999999
CONFIG_BUSYBOX_DEFAULT_FEATURE_BEEP_FREQ=0
CONFIG_BUSYBOX_DEFAULT_FEATURE_BEEP_LENGTH_MS=0
CONFIG_BUSYBOX_DEFAULT_CROND=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_CROND_DIR="/var/spool/cron"
CONFIG_BUSYBOX_DEFAULT_CRONTAB=y
CONFIG_BUSYBOX_DEFAULT_DEVMEM=y
CONFIG_BUSYBOX_DEFAULT_LOCK=y
CONFIG_BUSYBOX_DEFAULT_STRINGS=y
CONFIG_BUSYBOX_DEFAULT_TIME=y
CONFIG_BUSYBOX_DEFAULT_NC=y
CONFIG_BUSYBOX_DEFAULT_PING=y
CONFIG_BUSYBOX_DEFAULT_PING6=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_FANCY_PING=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_IPV6=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PREFER_IPV4_ADDRESS=y
CONFIG_BUSYBOX_DEFAULT_VERBOSE_RESOLUTION_ERRORS=y
CONFIG_BUSYBOX_DEFAULT_ARPING=y
CONFIG_BUSYBOX_DEFAULT_BRCTL=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_BRCTL_FANCY=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_BRCTL_SHOW=y
CONFIG_BUSYBOX_DEFAULT_IFCONFIG=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_IFCONFIG_STATUS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_IFCONFIG_HW=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_IFCONFIG_BROADCAST_PLUS=y
CONFIG_BUSYBOX_DEFAULT_IFUPDOWN_IFSTATE_PATH=""
CONFIG_BUSYBOX_DEFAULT_NETMSG=y
CONFIG_BUSYBOX_DEFAULT_NETSTAT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_NETSTAT_WIDE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_NETSTAT_PRG=y
CONFIG_BUSYBOX_DEFAULT_NSLOOKUP=y
CONFIG_BUSYBOX_DEFAULT_NTPD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_NTPD_SERVER=y
CONFIG_BUSYBOX_DEFAULT_ROUTE=y
CONFIG_BUSYBOX_DEFAULT_TELNET=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TELNET_TTYPE=y
CONFIG_BUSYBOX_DEFAULT_TELNETD=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TELNETD_STANDALONE=y
CONFIG_BUSYBOX_DEFAULT_TRACEROUTE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TRACEROUTE_VERBOSE=y
CONFIG_BUSYBOX_DEFAULT_DHCPD_LEASES_FILE=""
CONFIG_BUSYBOX_DEFAULT_UDHCPC=y
CONFIG_BUSYBOX_DEFAULT_UDHCP_DEBUG=0
CONFIG_BUSYBOX_DEFAULT_FEATURE_UDHCP_RFC3397=y
CONFIG_BUSYBOX_DEFAULT_UDHCPC_DEFAULT_SCRIPT="/usr/share/udhcpc/default.script"
CONFIG_BUSYBOX_DEFAULT_UDHCPC_SLACK_FOR_BUGGY_SERVERS=80
CONFIG_BUSYBOX_DEFAULT_IFUPDOWN_UDHCPC_CMD_OPTIONS=""
CONFIG_BUSYBOX_DEFAULT_VCONFIG=y
CONFIG_BUSYBOX_DEFAULT_WGET=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_WGET_STATUSBAR=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_WGET_AUTHENTICATION=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_WGET_LONG_OPTIONS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_MIME_CHARSET=""
CONFIG_BUSYBOX_DEFAULT_UPTIME=y
CONFIG_BUSYBOX_DEFAULT_FREE=y
CONFIG_BUSYBOX_DEFAULT_KILL=y
CONFIG_BUSYBOX_DEFAULT_KILLALL=y
CONFIG_BUSYBOX_DEFAULT_PGREP=y
CONFIG_BUSYBOX_DEFAULT_PIDOF=y
CONFIG_BUSYBOX_DEFAULT_PS=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_PS_WIDE=y
CONFIG_BUSYBOX_DEFAULT_BB_SYSCTL=y
CONFIG_BUSYBOX_DEFAULT_TOP=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TOP_CPU_USAGE_PERCENTAGE=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_TOP_CPU_GLOBAL_PERCENTS=y
CONFIG_BUSYBOX_DEFAULT_SV_DEFAULT_SERVICE_DIR=""
CONFIG_BUSYBOX_DEFAULT_ASH=y
CONFIG_BUSYBOX_DEFAULT_ASH_BASH_COMPAT=y
CONFIG_BUSYBOX_DEFAULT_ASH_JOB_CONTROL=y
CONFIG_BUSYBOX_DEFAULT_ASH_ALIAS=y
CONFIG_BUSYBOX_DEFAULT_ASH_GETOPTS=y
CONFIG_BUSYBOX_DEFAULT_ASH_BUILTIN_ECHO=y
CONFIG_BUSYBOX_DEFAULT_ASH_BUILTIN_PRINTF=y
CONFIG_BUSYBOX_DEFAULT_ASH_BUILTIN_TEST=y
CONFIG_BUSYBOX_DEFAULT_ASH_CMDCMD=y
CONFIG_BUSYBOX_DEFAULT_ASH_EXPAND_PRMT=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_SH_IS_ASH=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_BASH_IS_NONE=y
CONFIG_BUSYBOX_DEFAULT_SH_MATH_SUPPORT=y
CONFIG_BUSYBOX_DEFAULT_SH_MATH_SUPPORT_64=y
CONFIG_BUSYBOX_DEFAULT_FEATURE_SYSLOGD_READ_BUFFER_SIZE=0
CONFIG_BUSYBOX_DEFAULT_FEATURE_IPC_SYSLOG_BUFFER_SIZE=0
CONFIG_BUSYBOX_DEFAULT_LOGGER=y
CONFIG_PACKAGE_dnsmasq=y
CONFIG_PACKAGE_dropbear=y
#
# Configuration
#
CONFIG_PACKAGE_firewall=y
CONFIG_PACKAGE_fstools=y
CONFIG_PACKAGE_libc=y
CONFIG_PACKAGE_libgcc=y
CONFIG_PACKAGE_mtd=y
CONFIG_PACKAGE_netifd=y
CONFIG_PACKAGE_nvram=y
CONFIG_PACKAGE_opkg=y
CONFIG_PACKAGE_procd=y
CONFIG_PACKAGE_swconfig=y
CONFIG_PACKAGE_ubox=y
CONFIG_PACKAGE_ubus=y
CONFIG_PACKAGE_ubusd=y
CONFIG_PACKAGE_uci=y
#
# Administration
#
#
# Pmacct suite
#
#
# zabbix
#
#
# Boot Loaders
#
#
# Development
#
#
# Emulators
#
#
# Firmware
#
#
# Kernel modules
#
#
# Block Devices
#
#
# CAN Support
#
# CONFIG_PACKAGE_kmod-can is not set
#
# Cryptographic API modules
#
#
# Filesystems
#
#
# FireWire support
#
#
# Hardware Monitoring Support
#
#
# I2C support
#
#
# Input modules
#
#
# LED modules
#
CONFIG_PACKAGE_kmod-leds-gpio=y
CONFIG_PACKAGE_kmod-ledtrig-default-on=y
CONFIG_PACKAGE_kmod-ledtrig-netdev=y
CONFIG_PACKAGE_kmod-ledtrig-timer=y
#
# Libraries
#
CONFIG_PACKAGE_kmod-lib-crc-ccitt=y
#
# Native Language Support
#
#
# Netfilter Extensions
#
CONFIG_PACKAGE_kmod-ip6tables=y
CONFIG_PACKAGE_kmod-ipt-conntrack=y
CONFIG_PACKAGE_kmod-ipt-core=y
CONFIG_PACKAGE_kmod-ipt-nat=y
CONFIG_PACKAGE_kmod-ipt-nathelper=y
#
# Network Devices
#
CONFIG_PACKAGE_kmod-bgmac=y
#
# Network Support
#
CONFIG_PACKAGE_kmod-ipv6=y
CONFIG_PACKAGE_kmod-ppp=y
CONFIG_PACKAGE_kmod-pppoe=y
CONFIG_PACKAGE_kmod-pppox=y
CONFIG_PACKAGE_kmod-slhc=y
#
# Other modules
#
CONFIG_PACKAGE_kmod-gpio-button-hotplug=y
#
# PCMCIA support
#
#
# Proprietary BCM43xx WiFi driver
#
#
# SPI Support
#
#
# Sound Support
#
# CONFIG_PACKAGE_kmod-sound-core is not set
#
# USB Support
#
#
# Video Support
#
#
# Virtualization Support
#
#
# Voice over IP
#
#
# W1 support
#
#
# Wireless Drivers
#
#
# Languages
#
#
# Erlang
#
#
# Java
#
#
# JavaScript
#
#
# Lua
#
#
# PHP
#
#
# Perl
#
#
# Python
#
#
# Ruby
#
#
# Libraries
#
#
# Filesystem
#
#
# Firewall
#
CONFIG_PACKAGE_libip4tc=y
CONFIG_PACKAGE_libip6tc=y
CONFIG_PACKAGE_libxtables=y
#
# Printing
#
#
# SSL
#
#
# Sound
#
#
# database
#
CONFIG_PACKAGE_libblobmsg-json=y
CONFIG_PACKAGE_libiwinfo=y
CONFIG_PACKAGE_libjson-c=y
CONFIG_PACKAGE_libnl-tiny=y
CONFIG_PACKAGE_libubox=y
CONFIG_PACKAGE_libubus=y
CONFIG_PACKAGE_libuci=y
#
# LuCI
#
#
# 1. Collections
#
#
# 2. Modules
#
#
# 3. Applications
#
#
# 4. Themes
#
#
# 5. Translations
#
#
# 6. Protocols
#
#
# 7. Server Interfaces
#
#
# 8. Libraries
#
CONFIG_PACKAGE_luci-lib-core_source=y
CONFIG_PACKAGE_luci-lib-nixio_notls=y
#
# 9. Freifunk
#
#
# Mail
#
#
# Multimedia
#
#
# Streaming
#
#
# Network
#
#
# BitTorrent
#
#
# Captive Portals
#
#
# File Transfer
#
#
# Filesystem
#
#
# Firewall
#
CONFIG_PACKAGE_ip6tables=y
CONFIG_PACKAGE_iptables=y
#
# Firewall Tunnel
#
#
# FreeRADIUS (version 2)
#
#
# IP Addresses and Names
#
#
# IPv6 discovery tools
#
#
# Instant Messaging
#
#
# Linux ATM tools
#
#
# NMAP Suite
#
#
# NNTP
#
#
# NTRIP
#
#
# P2P
#
#
# Printing
#
#
# Routing and Redirection
#
#
# SSH
#
#
# THC-IPv6 attack and analyzing toolkit
#
#
# Telephony
#
#
# Time Synchronization
#
#
# VPN
#
#
# Version Control Systems
#
#
# Web Servers/Proxies
#
#
# dial-in/up
#
#
# firmware
#
#
# miredo: Teredo (IPv6 tunneling over UDP through NAT)
#
#
# wide-dhcpv6
#
#
# wireless
#
CONFIG_PACKAGE_odhcp6c=y
CONFIG_PACKAGE_odhcp6c_ext_prefix_class=0
CONFIG_PACKAGE_odhcp6c_ext_cer_id=0
CONFIG_PACKAGE_odhcpd=y
CONFIG_PACKAGE_odhcpd_ext_prefix_class=0
CONFIG_PACKAGE_odhcpd_ext_cer_id=0
CONFIG_PACKAGE_ppp=y
CONFIG_PACKAGE_ppp-mod-pppoe=y
CONFIG_WPA_MSG_MIN_PRIORITY=3
#
# Sound
#
#
# cmus
#
#
# Utilities
#
#
# Boot Loaders
#
#
# CPU tools
#
#
# Editors
#
#
# Filesystem
#
#
# RTKLIB Suite
#
#
# SSL
#
#
# Sound
#
#
# Terminal
#
#
# backup
#
#
# compression
#
#
# database
#
#
# disc
#
#
# filemanager
#
#
# zoneinfo
#
CONFIG_PACKAGE_iwinfo=y
CONFIG_PACKAGE_jshn=y
CONFIG_PACKAGE_libjson-script=y
#
# Video Streaming
#
#
# Xorg
#
#
# libraries
#Parameters preceeded with # were eliminated from this post for clarity and size constraints, but not from the build system version
boblfoot wrote:
Built an image with no wifi and such as suggested and it boots but ethernet will not connect
The most interesting in this build is not lack of WiFi, but the lack of tg3. Your testing was very helpful, thanks for your work on this!
So now we're sure it's b53 that causes reboots. Removing tg3 resulted in b53 not initializing and this stopped these reboots.
I don't have hardware using tg3, but I have some routers supported by bgmac, so I was able to test b53 a bit more. The fact is that b53 resets switch twice during standard boot. There is my log with some extra debugging logs:
[ 4.460000] b53_common: [DBG] b53_switch_init calling b53_switch_reset
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
[ 4.550000] b53_common: found switch: BCM53125, rev 4
[ 4.560000] bgmac: Broadcom 47xx GBit MAC driver loaded
(...)
[ 6.550000] libphy: bgmac-0-0:1e - Link is Up - 1000/Full
[ 12.620000] NET: Registered protocol family 10
[ 12.640000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
[ 12.650000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.680000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2
[ 12.690000] Backport generated by backports.git backports-20140221-0-g8e94650
[ 12.700000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.760000] xt_time: kernel timezone is -0000
[ 12.800000] cfg80211: Calling CRDA to update world regulatory domain
[ 12.800000] cfg80211: World regulatory domain updated:
[ 12.810000] cfg80211: DFS Master region: unset
[ 12.810000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 12.820000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.830000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.840000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.850000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.860000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 12.860000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 12.950000] PPP generic driver version 2.4.2
[ 12.960000] NET: Registered protocol family 24
[ 12.990000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 17.790000] b53_common: [DBG] b53_global_reset_switch calling b53_switch_reset
[ 17.800000] b53_common: [DBG] b53_switch_reset_gpio using 7Above proves that b53 resets switch twice:
Right before "b53_common: found switch"
Right after "Broadcom 43xx driver loaded"
It's really weird in case of your old logs, that we can see:
[ 5.970000] b53_common: found switch: BCM5325, rev 0which means the first switch reset didn't cause a reboot. Than we can see
[ 15.560000] Broadcom 43xx driver loaded [ Features: PNL ]and the device reboots...
It all means that for some reason, it's the second switch reset that causes reboot. My guess is that the first (incorrect) switch reset changes GPIO value from (default) 0 to 0 and then to 1. Later second (incorrect) switch reset changes GPIO value from 1 (last) value to 0 and this is the reason devices reboots.
(Last edited by Zajec on 13 Apr 2014, 10:33)
Page 1 of 2