juhosg wrote:
Sweet!
Building the image right now :-)
Regards,
Patrick
Topic: WD N600 support
The content of this topic has been archived between 1 Apr 2018 and 1 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Page 2 of 3
please to share when done! 
I don't have a openwrt dev setup anymore...
Success!
ar7240> tftpboot 0x81000000 openwrt-ar71xx-generic-mynet-n600-squashfs-sysupgrade.bin
Trying eth1
dup 1 speed AUTO(10/100/1000)
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.1
Filename 'openwrt-ar71xx-generic-mynet-n600-squashfs-sysupgrade.bin'.
Load address: 0x81000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##############################
done
Bytes transferred = 3145732 (300004 hex)
ar7240> erase 0x9F070000 +0x300004
Erase Flash from 0x9f070000 to 0x9f37ffff in Bank # 1
First 0x7 last 0x37 sector size 0x10000 55
Erased 49 sectors
ar7240> cp.b 0x81000000 0x9F070000 0x300004
Copy to Flash... write addr: 9f070000
done
ar7240> resetResetting...
U-Boot 1.1.4 (Mar 26 2012 - 21:54:50)
SVN revision: 51
Target board: WRG-ND16DRAM:
sri
Wasp 1.2
wasp_ddr_initial_config(255): (32bit) ddr2 init
128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 244k for U-Boot at: 87fc0000
Reserving 192k for malloc() at: 87f90000
Reserving 44 Bytes for Board Info at: 87f8ffd4
Reserving 36 Bytes for Global Data at: 87f8ffb0
Reserving 128k for boot params() at: 87f6ffb0
Stack Pointer at: 87f6ff98
Now running in RAM - U-Boot at: 87fc0000
id read 0x100000ff
flash size 16 MB, sector count = 256
Flash: 16 MB
pci_init_board: PCIe PLL not set for 40MHz refclk
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S27 PHY
: cfg1 0x5 cfg2 0x7114
eth0: 00:90:a9:a7:12:2b
s27 reg init
MEGA: athrs27_link_down all port...
MEGA: athrs27_link_down all port...
eth0 up
WASP ----> S27 PHY
: cfg1 0xf cfg2 0x7214
eth1: 00:90:a9:a7:12:2c
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
MEGA: athrs27_link_down all port...
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :50
MEGA: athrs27_link_down all port...
eth1 up
eth0, eth1
Hit any key to stop autoboot: 0
## Booting image at 9f070000 ...
Verifying Checksum ...
Uncompressing SEAMA linux.lzma ... OK
do_boot_linux entry = 80002000
## Transferring control to Linux (at address 00000000) ...
## Giving linux memsize in bytes, 134217728Starting kernel ...
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... done!
Starting kernel at 80060000...[ 0.000000] Linux version 3.10.12 (openwrt@openwrtbuild) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r37981) ) #1 Wed Sep 25 22:59:07 CEST 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:480.000MHz, AHB:240.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x07ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x07ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=MYNET-N600 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,64k(devdata)ro,64k(devconf)ro,15872k(firmware),64k(radiocfg)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126312k/131072k available (2196k kernel code, 4760k reserved, 588k data, 220k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] MIPS: machine is WD My Net N600
[ 0.110000] registering PCI controller with io_map_base unset
[ 0.550000] bio: create slab <bio-0> at 0
[ 0.550000] PCI host bridge to bus 0000:00
[ 0.560000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.560000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.570000] pci 0000:00:00.0: invalid calibration data
[ 0.580000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.580000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.590000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.590000] Switching to clocksource MIPS
[ 0.600000] NET: Registered protocol family 2
[ 0.600000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.600000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.610000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.610000] TCP: reno registered
[ 0.610000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.620000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.630000] NET: Registered protocol family 1
[ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.650000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.660000] msgmni has been set to 246
[ 0.660000] io scheduler noop registered
[ 0.670000] io scheduler deadline registered (default)
[ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.700000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.710000] console [ttyS0] enabled, bootconsole disabled
[ 0.710000] console [ttyS0] enabled, bootconsole disabled
[ 0.720000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.730000] m25p80 spi0.0: found mx25l12805d, expected m25p80
[ 0.730000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
[ 0.740000] 6 cmdlinepart partitions found on MTD device spi0.0
[ 0.740000] Creating 6 MTD partitions on "spi0.0":
[ 0.750000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.760000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.760000] 0x000000050000-0x000000060000 : "devdata"
[ 0.770000] 0x000000060000-0x000000070000 : "devconf"
[ 0.780000] 0x000000070000-0x000000ff0000 : "firmware"
[ 0.800000] 2 seama-fw partitions found on MTD device firmware
[ 0.810000] 0x000000070000-0x0000001b0000 : "kernel"
[ 0.820000] 0x0000001b0000-0x000000ff0000 : "rootfs"
[ 0.820000] mtd: partition "rootfs" set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.840000] 0x000000370000-0x000000ff0000 : "rootfs_data"
[ 0.840000] 0x000000ff0000-0x000001000000 : "radiocfg"
[ 0.860000] libphy: ag71xx_mdio: probed
[ 0.870000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.430000] eth0: Found an AR934X built-in switch
[ 2.460000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 3.010000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 3.020000] TCP: cubic registered
[ 3.030000] NET: Registered protocol family 17
[ 3.030000] 8021q: 802.1Q VLAN Support v1.8
[ 3.040000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
[ 3.050000] Freeing unused kernel memory: 220K (80319000 - 80350000)
procd: Console is alive
procd: - watchdog -
[ 5.130000] usbcore: registered new interface driver usbfs
[ 5.140000] usbcore: registered new interface driver hub
[ 5.140000] usbcore: registered new device driver usb
[ 5.150000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.160000] ehci-platform: EHCI generic platform driver
[ 5.170000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.170000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.180000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.210000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.210000] hub 1-0:1.0: USB hub found
[ 5.220000] hub 1-0:1.0: 1 port detected
[ 5.220000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
kmod: ran 21 iterations
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
[ 7.520000] eth0: link up (1000Mbps/Full duplex)
mount_root: jffs2 is not ready - marker found
[ 9.630000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[ 10.540000] NET: Registered protocol family 10
[ 10.560000] nf_conntrack version 0.5.0 (1977 buckets, 7908 max)
[ 10.570000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 10.590000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 10.600000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 10.610000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.650000] xt_time: kernel timezone is -0000
[ 10.670000] cfg80211: Calling CRDA to update world regulatory domain
[ 10.670000] cfg80211: World regulatory domain updated:
[ 10.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.690000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.690000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 10.700000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 10.710000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.720000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.760000] PPP generic driver version 2.4.2
[ 10.780000] NET: Registered protocol family 24
[ 10.840000] cfg80211: Calling CRDA for country: US
[ 10.850000] cfg80211: Regulatory domain changed to country: US
[ 10.850000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 10.860000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 10.870000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 10.880000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.880000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.890000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 10.910000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 10.910000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 10.940000] ieee80211 phy1: Atheros AR9300 Rev:3 mem=0xb0000000, irq=40
[ 17.870000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 17.870000] device eth0 entered promiscuous mode
[ 17.890000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 17.920000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 18.970000] eth0: link up (1000Mbps/Full duplex)
[ 18.970000] br-lan: port 1(eth0) entered forwarding state
[ 18.980000] br-lan: port 1(eth0) entered forwarding state
[ 18.980000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.000000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 20.050000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 20.060000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 20.060000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 20.980000] br-lan: port 1(eth0) entered forwarding stateBusyBox v1.19.4 (2013-09-25 22:53:22 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands._______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38197)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/# done.
[ 83.130000] jffs2: notice: (869) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
procd: - init complete -root@OpenWrt:/#
Thanks Gabor!!!
The LAN ports work, I can ping my PC (192.168.1.10).
@CRC: There seem to be prebuilt nightly images at http://downloads.openwrt.org/snapshots/trunk/ar71xx/
=>
openwrt-ar71xx-generic-mynet-n600- ...
I haven't tried them though, but they should work I think :-)
(Last edited by EvilDevil on 25 Sep 2013, 22:37)
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 12.5M 468.0K 12.0M 4% /
/dev/root 1.8M 1.8M 0 100% /rom
tmpfs 61.7M 56.0K 61.7M 0% /tmp
tmpfs 61.7M 28.0K 61.7M 0% /tmp/root
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock7 12.5M 468.0K 12.0M 4% /overlay
overlayfs:/overlay 12.5M 468.0K 12.0M 4% /
root@OpenWrt:/# free -m
total used free shared buffers
Mem: 126396 19832 106564 0 1528
-/+ buffers: 18304 108092
Swap: 0 0 0
Looks very good! :-)
Next steps:
Flashed the firmware from the OpenWrt trunk snapshots download page(via serial/tftpboot). Installed LuCI, configured WiFi (works!), checked switch-configuration (OpenWrt discovered it as "switch0 (AR934X built-in switch)"): VLAN tagging is available.
Performance (loading LuCI pages) so far is quite fast.
=> Should be safe to try it out via web-recovery-flashing ( http://wdc.custhelp.com/app/answers/detail/a_id/9618/ ) with the sysupgrade image.
Best regards,
Patrick
(Last edited by EvilDevil on 26 Sep 2013, 06:45)
Downloading to try this now
Ok, here we go:
Updating File
Don't Power Down.
Please wait for seconds...It seems the instructions on the WD web site conflict themselves - it says to set your PC to 192.168.1.50, then just below tells you to use 192.168.1.10. Interestingly, I couldn't get to the recovery page (http://192.168.1.1) when using 192.168.1.50 on my PC - not sure if its just chance or firewalled. It also seems the unit doesn't respond to pings while in this mode either - so you can't use this to make sure everything is up and running.
Either way, after a while, the power light started flashing rapidly, after a while went solid...
Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
Sweet.
telnet to 192.168.1.1:
=== IMPORTANT ============================
Use 'passwd' to set your login password
this will disable telnet and enable SSH
------------------------------------------
BusyBox v1.19.4 (2013-09-25 18:09:41 PDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38181)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#WINNAH!!!
I've updated the Wiki page that I started:
http://wiki.openwrt.org/toh/wd/n600
It now has instructions on how to install OpenWRT etc as well as serial port info...
great work! 
even managed to install luci now and seems to run without problems.
(Last edited by drdoolittle on 26 Sep 2013, 11:48)
Great, everything work. I put n600 in the wifi routing mode in 5 minuts and connect two differents net via wifi. But I have one problem, USB HDD can not be recognize.
(Last edited by istarenki on 27 Sep 2013, 08:34)
istarenki wrote:
Great, everything work. I put n600 in the wifi routing mode in 5 minuts and connect two differents net via wifi.
how did you do that? I also want to extend my wifi range via WDS. i've got an easybox 802 which I put in WDS mode with connection to the N600, but how do I set the N600 to the correct mode to make a connection?
how did you do that? I also want to extend my wifi range via WDS. i've got an easybox 802 which I put in WDS mode with connection to the N600, but how do I set the N600 to the correct mode to make a connection?
Hm, funny, all mornig was everything ok, but when I start playing with mounting I lose everythin and now I am trying again.
OK, First I install luCi
and after that I went to meni Network/Wifi.
You will see 2 net, one 2.4 Ghz and one is 5 Ghz. I use option scan on the 2.4 net and my another network apear, after that I simpli made connection with my old wifi net. (my old net is on x.x.5.0/24 name NN and net on n600 is x.x.1.0/24 name MMnet) and everything start work. When I finished with evethig on the meni Network/WiFi under 2.4 net I got two network. MMnet was marked like master and NN netwokr was marked like client. But after couple hours of playing I did something and lose everythig and now I am trying to make again.
I found a quite simple tutorial how to enable WDS:
http://www.youtube.com/watch?v=3rbsh2zxPnk
And I also found this in order to support bridging when in client mode:
http://wiki.openwrt.org/doc/recipes/relayclient
(Last edited by drdoolittle on 27 Sep 2013, 19:03)
@juhosg: Awesome! I tried something similar but didn't succeed. Maybe I shouldn't have given up so quickly. Thanks for the effort.
I clean my WD and start from zero. Ok, I put everythin in routing mode, two diferrents nets via wifi. I do not have any problem with that. I did same like in that youtube movie. But I have two quoestion:
1st. My luci look different then this on youtube end openwrt wiki. Is it ok ? (I am totaly noob for openwrt, not for nets)
2nd. I can not make ext HDD whic I plug in USB. Do you sucecced to connect ext hdd on wd n600 usb port.
(Last edited by istarenki on 28 Sep 2013, 18:48)
i dont think USB works on openwrt
this one looks like this:
http://wiki.hidemyass.com/images/manual/86357142.gif
my other openwrt routers look like this:
http://dualcore.be/wp-content/uploads/2 … luci_7.png
did luci have an upgrade?
You have a different theme, that is all...
i really dont know what i'm doing
i have 3 routers on openwrt
1st one was easiest, it was Attitude Adjustment so i just flashed it and loaded the web and was away
this one and my 2nd was breaker barrier and to telnet in, set them up on the network and it downloaded the packages and stuff
not sure what Luci is doing far as changing schemes and such as it just grabs what there is when i set them up
i assume that if i set up any router now it has the new scheme
anyway, the n600 seems to be great under BB
good cpu, 128mb ram, shame its only 10/100
TonyJZX wrote:
good cpu, 128mb ram, shame its only 10/100
Yeah, well - that's faster than the wifi will ever go anyhow 
I solve problem with usb, almost . Problem was that firmware was updated and kmod-xxxx did not work. When I put latest firmware 28.09.2013 and put depednices files I got usb hdd on the router. Now I am trying to mount hdd on openwrt and make share.
Update: Everthig works. Wifi routin, usb hdd with movies, Ushare (no subtitles), I can use wifi printer which is on another subnet. Now I am trying to put in function minidnla. . Openwrt make something incredible from cheap n600
(Last edited by istarenki on 29 Sep 2013, 14:02)
So, if you're having wifi dropout problems like me - try this build:
Linux version 3.10.13 (openwrt@openwrt) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38259) ) #1 Mon Sep 30 02:06:02 EDT 2013
https://www.crc.id.au/files/openwrt-ar7 … pgrade.bin
It contains a couple of patches that haven't made it into the built trunk images as yet that may fix the dropout problems...
I do not have WiFi dropouts, everything work fine, except minidnla. If I restart router I have to remove luci-app-minidlna install again, enable in Luci and etc/init.d minidlna restart. After that and DLNA works. I put n600 in another room, connect desktop komp and wd tv live (b-rad) via utp5, wd my book hdd via usb. N600 is WIFI conected to enkom router (from net provider, no openwrt) to internet. Two samsung tv are connected via 5ghz to n600. I have internet on boat subs and everything works fine. Oh, I almost forget, WiFi epson print,scan, copy is on enkom sub and I can print from n600 subnet to enkom subote.
From my testing, it seems to be that it is only 2.4GHz and Android devices that seem to cause the problem. Other devices seem to work more as expected... Testing is still ongoing however....
Hm, I typing this on Android htc Flyer tablet on n600 net, no WiFi dropouts.
It usually takes upwards of 18 hours uptime before it starts to act up...
Sometimes a "wifi down && wifi up" fixes it, sometimes I need to reboot the whole system.
When it happens, I can't even access the web interface or ping the router via the 2.4GHz wifi side of things...
Page 2 of 3