The content of this topic has been archived on 20 Apr 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.
Hello to all,
I bought the router (extender) TP-Link-WA830RE V2 , someone has already installed openwrt for this router?
Openwrt is compatible with the TP-LINK-WA830RE V2?
I searched on the "Supported Hardware - Router type" site openwrt but it is not present.
Thanks in advance.
MisteroX
For developers :
This is boot from serial console router TL-WA830RE V2.
Serial console (TX,RX,GND)
- Detail from uboot serial console
wasp> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art)
bootcmd=bootm 0x9f020000
bootdelay=1
baudrate=115200
ethaddr=0xXX:0xXX:0xXX:0xXX:0xXX:0xXX
ipaddr=192.168.1.111
serverip=192.168.1.100
dir=
bc=ap123
lu=tftp 0x81000000 ${dir}u-boot.bin&&erase 0x9f000000 +$filesize;cp.b $fileaddr 0x9f000000 $filesize
lf=tftp 0x81000000 ${dir}${bc}-squashfs&&erase 0x9f120000 +$filesize;cp.b $fileaddr 0x9f120000 $filesize
stdin=serial
stdout=serial
stderr=serial
ethact=eth0Environment size: 565/65532 bytes
- Detail boot firmware from serial console :
U-Boot 1.1.4 (Oct 8 2012 - 16:51:51)
U-boot AP123
DRAM: 32 MB
id read 0x100000ff
Flash: 4 MB
Using default environmentIn: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
wasp reset mask:c03300
WASP ----> S27 PHY
GMAC: cfg1 0x5 cfg2 0x7114
eth0: xx:xx:xx:xx:xx:xx
s27 reg init
athrs27_phy_setup ATHR_PHY_CONTROL 4: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4: 0x10
eth0 up
WASP ----> S27 PHY
GMAC: cfg1 0xf cfg2 0x7214
eth1: xx:xx:xx:xx:xx:xx
s27 reg init lan
ATHRS27: resetting s27
ATHRS27: s27 reset done
athrs27_phy_setup ATHR_PHY_CONTROL 0: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 1: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 2: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2: 0x10
athrs27_phy_setup ATHR_PHY_CONTROL 3: 0x1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3: 0x10
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OKStarting kernel ...
Booting Atheros AR934x
Linux version 2.6.31--LSDK-9.2.0_U5.508 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #14 Mon Oct 8 16:55:43 CST 2012
flash_size passed from bootloader = 4
Ram size passed from bootloader =33554432
CPU revision is: 0001974c (MIPS 74Kc)
ath_sys_frequency: cpu srif ddr srif cpu 535 ddr 400 ahb 200
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:128k(u-boot),1024k(kernel),2816k(rootfs),64k(config),64k(art) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 30132k/32768k available (1723k kernel code, 2636k reserved, 425k data, 112k init, 0k highmem)
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop... 267.26 BogoMIPS (lpj=534528)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
ATH GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
5 cmdlinepart partitions found on MTD device ath-nor0
Creating 5 MTD partitions on "ath-nor0":
0x000000000000-0x000000020000 : "u-boot"
0x000000020000-0x000000120000 : "kernel"
0x000000120000-0x0000003e0000 : "rootfs"
0x0000003e0000-0x0000003f0000 : "config"
0x0000003f0000-0x000000400000 : "art"
->Oops: flash id 0x10215 .
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Port Status 1c000004
ath-ehci ath-ehci.0: ATH EHCI
ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 13
ehci_reset Port Status 1c000000
ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
athwdt_init: Registering WDT success
ath_otp_init: Registering OTP success
ath_clksw_init: Registering Clock Switch Interface success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freedinit started: BusyBox v1.01 (2012.09.06-08:33+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko': No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko': No such file or directory(none) mips #14 Mon Oct 8 16:55:43 CST 2012 (none)
(none) login: Now flash open!
Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:1 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2D82
ATHR_GMAC: RX TASKLET - Pkts per Intr:32
mac:0 Registering S27....
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 128
ATHR_GMAC: Mac capability flags : 2582
athr_gmac_ring_alloc Allocated 640 at 0x81e2dc00
athr_gmac_ring_alloc Allocated 2048 at 0x81ccb000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
athr_gmac_ring_alloc Allocated 640 at 0x81e2d800
athr_gmac_ring_alloc Allocated 2048 at 0x81f00800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS27: resetting s27
ATHRS27: s27 reset done
++++ athrs27_igmp_setup once
port0 vid is 0xb000b
port1 vid is 0x30003
port2 vid is 0x50005
port3 vid is 0x70007
port4 vid is 0x90009
++ PVID: 0x0000000b, bitmap: 0x0000001f
++ PVID: 0x00000003, bitmap: 0x0000001f
++ PVID: 0x00000005, bitmap: 0x0000001f
++ PVID: 0x00000007, bitmap: 0x0000001f
++ PVID: 0x00000009, bitmap: 0x0000001f
vtable vid: 0x00000002, bitmap 0x00000003
vtable vid: 0x00000004, bitmap 0x00000005
vtable vid: 0x00000006, bitmap 0x00000007
vtable vid: 0x00000008, bitmap 0x00000009
vtable vid: 0x0000000a, bitmap 0x0000000b
vtable vid: 0x0000000c, bitmap 0x0000000d
vtable vid: 0x0000000e, bitmap 0x0000000f
vtable vid: 0x00000010, bitmap 0x00000011
vtable vid: 0x00000012, bitmap 0x00000013
vtable vid: 0x00000014, bitmap 0x00000015
vtable vid: 0x00000016, bitmap 0x00000017
vtable vid: 0x00000018, bitmap 0x00000019
vtable vid: 0x0000001a, bitmap 0x0000001b
vtable vid: 0x0000001c, bitmap 0x0000001d
vtable vid: 0x0000001e, bitmap 0x0000001f
vtable vid: 0x00000020, bitmap 0x00000021
Setting PHY...
device eth1 entered promiscuous mode
Now flash open!
athr_gmac_ring_free Freeing at 0x81e2dc00
athr_gmac_ring_free Freeing at 0x81ccb000
athr_gmac_ring_alloc Allocated 640 at 0x81e2dc00
athr_gmac_ring_alloc Allocated 2048 at 0x81ea8800
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
enet0 port0 up
ATHR_GMAC: Enet Unit:0 PHY:0 is UP Mii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7115 ifctl 0x10000 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 1(eth1) entering forwarding state
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license 'Proprietary' taints kernel.
Disabling lock debugging ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U10.1020 (Atheros/multi-bss)
__ath_attach: Set global_scn[0]
ACBKMinfree = 48
ACBEMinfree = 32
ACVIMinfree = 16
ACVOMinfree = 0
CABMinfree = 48
UAPSDMinfree = 0
Restoring Cal data from Flash
ath_get_caps[5105] rx chainmask mismatch actual 3 sc_chainmak 0
ath_get_caps[5080] tx chainmask mismatch actual 3 sc_chainmak 0
wifi0: Atheros 9340: mem=0xb8100000, irq=2
====>>>>SystemMode : Standard AP
wlan_vap_create : enter. devhandle=0x81fec2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x81fec2c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created
====>>>>wlan: rand channel 6DES SSID SET=TP-LINK_Extender_B57EF8
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
athr_gmac_ring_free Freeing at 0x81e2dc00
athr_gmac_ring_free Freeing at 0x81ea8800
br0: port 1(eth1) entering disabled state
athr_gmac_ring_alloc Allocated 640 at 0x81f56400
athr_gmac_ring_alloc Allocated 2048 at 0x81ea8000
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY...
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled stateDES SSID SET=TP-LINK_Extender_B57EF8
br0: port 2(ath0) entering forwarding state
====>>>>ssss_1295
====>>>>cmdCtrl open success
====>>>>eventCtrl open success
====>>>>eventCtrl attach success
====>>>>------------swWlanExtenderStart---------------
====>>>>swWlanExtenderThread
====>>>>create extender thread ok,pid:6151
====>>>>linkStatus = 0
====>>>>create ssid thread success, pid:8201
====>>>>linkStatus is 0
ATHR_GMAC: GE0 RX DMA ENABLE
enet0 port0 up
ATHR_GMAC: Enet Unit:0 PHY:0 is UP Mii 100Mbps full duplex
ATHR_GMAC: done cfg2 0x7115 ifctl 0x10000 miictrl
WASP ----> S27 PHY MDIO
Setting Drop CRC Errors, Pause Frames and Length Error frames
br0: port 2(ath0) entering disabled state
br0: port 1(eth1) entering forwarding state
br0: port 2(ath0) entering forwarding state
====>>>>linkStatus = 1
====>>>>DHCP start.dhcpc.c,dhcpcStart,894
====>>>>DHCP end.dhcpc.c,dhcpcStNow flash open!
art,954
Erase from 0X3E0000 to 0X3EC808:.
Program from 0X3E0000 to 0X3EC808:
write successfully
Now flash open!
Erase from 0X3E0000 to 0X3EC808:.
Program from 0X3E0000 to 0X3EC808:
write successfully
====>>>>lan type detect start.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>wzd start ROOTAP CONNECT 1
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.
====>>>>lan type detect retry.TL-WA830RE mips #14 Mon Oct 8 16:55:43 CST 2012 (none)
TL-WA830RE login: admin====>>>>lan type detect retry.
Password: ====>>>>lan type detect retry.
====>>>>lan type detect fail.
====>>>>lanTypeDectect, 1127
Now flash open!
Erase from 0X3E0000 to 0X3EC808:.
Program from 0X3E0000 to 0X3EC808:
write successfully
br0: port 2(ath0) entering disabled state
br0: port 2(ath0) entering forwarding state
Login incorrect
TL-WA830RE login:
I tried to login with the following users/password with negative results.
root / 5up
root / root
root / passwd
admin / admin
Anyone knows how to retrieve the root pwd ?
Here there are image of board and serial console. http://misterox.altervista.org/dokuwiki … wa830re_v2
Bye
MisteroX
(Last edited by misteroX on 18 May 2013, 13:53)
Hello, I saw that you're the only one who has posted information about this repeater .. I find myself stuck with repeater. I think something went wrong during recovery from ddwrt to OEM. I have a serial interface, and I have already solder the pins to connect. Could you help on this?
My mail is anto.auteri@gmail.com
(Last edited by mac93 on 10 Dec 2016, 14:28)
The discussion might have continued from here.