Hello Sir,
I have the same model (D-Link 2640U which had firmware ME_2.01 with C2 Hardware version) with the latest firmware 2.05 from dlink ftp, I tried many many things but not working. can anybody tell me if this is a fault in the board capacitors or something else although all PCB parts looks in a good condition as seen in image and only the power led and LAN connected cable are only lighting some times the internet led is flashing also for few seconds...
N.B: I changed also the power adapter but the same problem.
Here is the boot log output via console cable...
I have a D-Link 2640U which had firmware RU_2.01 with C2 Hardware version
CFE version 1.0.37-12.1 for BCM96338 (32bit,SP,BE)
Build Date: Fri Jul 9 23:49:54 CST 2010 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Serial flash device: name MX25L3205D, id 0xc215, size 4096KB
100 MB Full-Duplex (auto-neg)
CPU type 0x29010: 240MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80528DF0 (1211888)
Initialized Data: 0x8041DD10 - 0x80420600 (10480)
BSS Area: 0x80420600 - 0x80426DF0 (26608)
Local Heap: 0x80426DF0 - 0x80526DF0 (1048576)
Stack Area: 0x80526DF0 - 0x80528DF0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD04 (118020)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-15) : 96333AWG
Number of MAC Addresses (1-32) : 2
Base MAC Address : 1c:bd:b9:78:05:e1
PSI Size (1-64) KBytes : 24
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbfc10000) ...
Code Address: 0x80010000, Entry Address: 0x801c3018
Decompression OK!
Entry at 0x801c3018
Closing network.
Starting program at 0x801c3018
Linux version 2.6.8.1 (zhouyu@localhost.localdomain) (gcc version 3.4.2) #1 Mon Nov 29 21:55:02 CST 2010
Serial flash device: name MX25L3205D, id 0xc215, size 4096KB
96333AWG prom init
CPU revision is: 00029010
Determined physical RAM map:
memory: 00fa0000 @ 00000000 (usable)
On node 0 totalpages: 4000
DMA zone: 4000 pages, LIFO batch:1
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 8kB 2-way, linesize 16 bytes.
PID hash table entries: 64 (order 6: 512 bytes)
Using 120.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 13828k/16000k available (1508k kernel code, 2152k reserved, 227k data, 72k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 239.20 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 4096K with 1024 sectors
File system address: 0xbfc10100
Blk# BlkOff Blks MemLen Partition Name
0 1408 1 1024 NVRAM
1010 0 6 24576 Config 2
1016 0 2 8192 Scratch PAD
1018 0 6 24576 Config 1
Can't analyze prologue code at 80187cb4
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
brcmboard: brcm_board_init entry
D%G
CFE version 1.0.37-12.1 for BCM96338 (32bit,SP,BE)
Build Date: Fri Jul 9 23:49:54 CST 2010 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbfc00000
Initializing Arena.
Initializing Devices.
Serial flash device: name MX25L3205D, id 0xc215, size 4096KB
100 MB Full-Duplex (auto-neg)
CPU type 0x29010: 240MHz
Total memory: 16777216 bytes (16MB)
Total memory used by CFE: 0x80401000 - 0x80528DF0 (1211888)
Initialized Data: 0x8041DD10 - 0x80420600 (10480)
BSS Area: 0x80420600 - 0x80426DF0 (26608)
Local Heap: 0x80426DF0 - 0x80526DF0 (1048576)
Stack Area: 0x80526DF0 - 0x80528DF0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD04 (118020)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-15) : 96333AWG
Number of MAC Addresses (1-32) : 2
Base MAC Address : 1c:bd:b9:78:05:e1
PSI Size (1-64) KBytes : 24
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>
and continuous restarts when arrives "brcmboard: brcm_board_init entry" and writes "D%G"
I'll appreciate any help
Thanks,