Hi,
I have a Livebox 1 router with a custom Redboot on which I was running a Backfire 10.03.1 image from here. Everything was working fine, including the miniPCI wireless card (BCM4318). For instance, when I run:
cat /proc/bus/pci/devices
I got the info about the miniPCI card inserted.
Now, for a project I am working on, I tried to compile Attitude 12.09 for this board, but I couldn't get to make the miniPCI slot work. In the configuration process added the b43 drivers for the wireless card, and also the ath9k for another card I have, but there's no way to see them in /proc/bus/pci/devices. The kmod-bcma was selected too.
In the kernel configuration I made sure that "Support for PCI controller" was selected in "Bus options (PCI, PCMCIA...", and later I also tried enabling "Device drivers ---> Broadcom specific AMBA ---> BCMA Support". The result is that no miniPCI card is detected at all.
What can I do to make the miniPCI slot work? If it worked in 10.03.1... it should be working with 12.09. Shouldn't it? Any help will be appreciated.
Thank you very much!
[ 0.000000] Linux version 3.3.8 (lino@xeon) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #7 Wed Apr 17 11:18:24 CEST 2013
[ 0.000000] Detected Broadcom 0x6348 CPU revision b0
[ 0.000000] CPU frequency is 256 MHz
[ 0.000000] 16MB of RAM installed
[ 0.000000] registering 37 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 36 on device: bcm63xx-gpio
[ 0.000000] board_livebox: Livebox BLUE5G.9
[ 0.000000] board_livebox: resetting gpio6 for eth1...
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00029107 (Broadcom BMIPS3300)
[ 0.000000] board_livebox: board name: Livebox-blue-5g
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 01000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00001000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00001000
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes)
[ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
[ 0.000000] Memory: 13044k/16384k available (2239k kernel code, 3340k reserved, 398k data, 164k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 254.46 BogoMIPS (lpj=508928)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.064000] NET: Registered protocol family 16
[ 0.088000] board_livebox: flash address is: 0x1fc00000, forcing to: 0x1e400000
[ 0.132000] bio: create slab <bio-0> at 0
[ 0.152000] Switching to clocksource MIPS
[ 0.180000] NET: Registered protocol family 2
[ 0.188000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.196000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.204000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.208000] TCP: Hash tables configured (established 512 bind 512)
[ 0.216000] TCP reno registered
[ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.224000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.232000] NET: Registered protocol family 1
[ 0.248000] audit: initializing netlink socket (disabled)
[ 0.252000] type=2000 audit(0.252:1): initialized
[ 0.260000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.268000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.280000] msgmni has been set to 25
[ 0.284000] io scheduler noop registered
[ 0.288000] io scheduler deadline registered (default)
[ 0.300000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
[ 0.308000] console [ttyS0] enabled, bootconsole disabled
[ 0.308000] console [ttyS0] enabled, bootconsole disabled
[ 0.332000] physmap platform flash device: 00800000 at 1e400000
[ 0.340000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[ 0.348000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.356000] Amd/Fujitsu Extended Query version 1.3.
[ 0.360000] number of CFI chips: 1
[ 0.364000] Searching for RedBoot partition table in physmap-flash.0 at offset 0x7f0000
[ 0.392000] 6 RedBoot partitions found on MTD device physmap-flash.0
[ 0.396000] Creating 6 MTD partitions on "physmap-flash.0":
[ 0.404000] 0x000000000000-0x000000030000 : "RedBoot"
[ 0.416000] 0x000000030000-0x000000170000 : "kernel"
[ 0.432000] 0x000000170000-0x000000310000 : "user_fs"
[ 0.444000] 0x000000310000-0x0000007f0000 : "rootfs_data"
[ 0.460000] 0x0000007f0000-0x0000007ff000 : "FIS directory"
[ 0.472000] 0x0000007ff000-0x000000800000 : "RedBoot config"
[ 0.504000] bcm63xx_enet MII bus: probed
[ 0.512000] bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (1)]
[ 0.528000] bcm63xx_enet MII bus: probed
[ 0.532000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 31 [Generic PHY]
[ 0.552000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.572000] TCP cubic registered
[ 0.576000] NET: Registered protocol family 17
[ 0.580000] 8021q: 802.1Q VLAN Support v1.8
[ 0.600000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.608000] Freeing unused kernel memory: 164k freed
awk: /proc/cpuinfo: No such file or directory
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 11.516000] JFFS2 notice: (325) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 15.260000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 15.268000] Backport based on wireless-testing.git master-2012-09-07
[ 15.272000] compat.git: wireless-testing.git
[ 15.384000] cfg80211: Calling CRDA to update world regulatory domain
[ 15.388000] cfg80211: World regulatory domain updated:
[ 15.396000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.404000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.412000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.420000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 15.428000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 15.436000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 16.460000] usbcore: registered new interface driver usbfs
[ 16.468000] usbcore: registered new interface driver hub
[ 16.476000] usbcore: registered new device driver usb
[ 16.540000] lib80211: common routines for IEEE802.11 drivers
[ 18.304000] usbcore: registered new interface driver rt2800usb
[ 18.364000] bcma: exports duplicate symbol bcma_core_dma_translation (owned by kernel)
[ 18.972000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 19.084000] Button Hotplug driver version 0.4.1
[ 19.448000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.960000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 20.048000] nf_conntrack version 0.5.0 (206 buckets, 824 max)
[ 20.964000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 21.076000] bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
[ 21.080000] bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 1
[ 21.092000] bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
[ 21.156000] hub 1-0:1.0: USB hub found
[ 21.160000] hub 1-0:1.0: 1 port detected
[ 21.232000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 21.492000] usb 1-1: new full-speed USB device number 2 using bcm63xx_ohci
[ 21.812000] usb 1-1: reset full-speed USB device number 2 using bcm63xx_ohci
[ 31.760000] device eth1 entered promiscuous mode
[ 34.656000] eth0: link UP - 100/full - flow control off
(Last edited by lordroger on 17 Apr 2013, 10:57)