Since Yesterday my Routers Usb is not functioning properly..
[ 12.130000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.260000] NET: Registered protocol family 24
[ 12.280000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.300000] ehci-platform: EHCI generic platform driver
[ 12.300000] ehci-platform ehci-platform: EHCI Host Controller
[ 12.310000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 12.320000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 12.340000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 12.340000] hub 1-0:1.0: USB hub found
[ 12.340000] hub 1-0:1.0: 1 port detected
[ 12.370000] nf_conntrack version 0.5.0 (452 buckets, 1808 max)
[ 12.620000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.670000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 12.840000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.020000] usb 1-1: new high-speed USB device number 3 using ehci-platform
[ 13.270000] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 13.690000] usb 1-1: device not accepting address 4, error -71
[ 13.810000] usb 1-1: new high-speed USB device number 5 using ehci-platform
[ 14.300000] usb 1-1: device not accepting address 5, error -71
[ 14.300000] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 19.610000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.610000] device eth0 entered promiscuous mode
[ 19.620000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 19.630000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 20.430000] eth0: link up (1000Mbps/Full duplex)
[ 20.430000] br-lan: port 1(eth0) entered forwarding state
[ 20.440000] br-lan: port 1(eth0) entered forwarding state
[ 20.440000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 20.450000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 22.440000] br-lan: port 1(eth0) entered forwarding state
[ 29.890000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 29.910000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 29.910000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 34.480000] jffs2: notice: (1048) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 1645.610000] usb 1-1: new high-speed USB device number 6 using ehci-platform
[ 1645.860000] usb 1-1: new high-speed USB device number 7 using ehci-platform
[ 1646.110000] usb 1-1: new high-speed USB device number 8 using ehci-platform
[ 1646.530000] usb 1-1: device not accepting address 8, error -71
[ 1646.650000] usb 1-1: new high-speed USB device number 9 using ehci-platform
[ 1647.070000] usb 1-1: device not accepting address 9, error -71
[ 1647.070000] hub 1-0:1.0: unable to enumerate USB device on port 1
it happened all of a sudden and installing any other Firmware doesnt help at all.. trying to get it running again need it for 3g