I need some help with my 703.
I tried to flash it because it was chinese. I used this guide http://wiki.openwrt.org/toh/tp-link/tl- … inal.image
I flashed openwrt-ar71xx-generic-tl-wr703n-v1-squashfs-factory.bin and it loaded up, router reboted and .....
NADA -nothing.
I cant get to it either by ethernet or wifi, when i power up blue led blinks shortly then its off(~10sec) then it blinks on-off in ~1sec intervals. If press reset button led starts to blink faster.
I tried to connect it with serial console and i get this
U-Boot 1.1.4 (Sep 25 2012 - 09:04:47)
AP121 (ar9330) U-boot
DRAM: 32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Mon Sep 3 17:51: 18 UTC 2012
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29136k/32768k available (2198k kernel code, 3632k reserved, 412k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[ 0.340000] bio: create slab <bio-0> at 0
[ 0.350000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.360000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.370000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.380000] TCP reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 56
[ 0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.470000] console [ttyATH0] enabled, bootconsole disabled
[ 0.470000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] m25p80 spi0.0: found en25q32b, expected m25p80
[ 0.480000] m25p80 spi0.0: en25q32b (4096 Kbytes)
[ 0.490000] 5 tp-link partitions found on MTD device spi0.0
[ 0.490000] Creating 5 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.510000] 0x000000020000-0x000000108374 : "kernel"
[ 0.510000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.520000] 0x000000108374-0x0000003f0000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=120000
[ 0.550000] 0x0000002d0000-0x0000003f0000 : "rootfs_data"
[ 0.560000] 0x0000003f0000-0x000000400000 : "art"
[ 0.570000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.590000] ag71xx_mdio: probed
[ 0.600000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.150000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.160000] TCP cubic registered
[ 1.160000] NET: Registered protocol family 17
[ 1.170000] 8021q: 802.1Q VLAN Support v1.8
[ 1.170000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.180000] Freeing unused kernel memory: 208k freed
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
[ 6.330000] JFFS2 notice: (436) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 1 orphan) and 20 of xref (0 dead, 1 1 orphan) found.
switching to jffs2
- init -
Please press Enter to activate this console. [ 8.200000] Compat-wireless backport release: compat-wireless-2012-07-13
[ 8.200000] Backport based on wireless-testing.git master-2012-07-16
[ 8.210000] compat.git: wireless-testing.git
[ 8.380000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.380000] cfg80211: World regulatory domain updated:
[ 8.390000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.390000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.400000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.410000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.420000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.420000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.630000] usbcore: registered new interface driver usbfs
[ 8.640000] usbcore: registered new interface driver hub
[ 8.640000] usbcore: registered new device driver usb
[ 9.130000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 9.140000] cfg80211: Calling CRDA for country: US
[ 9.140000] cfg80211: Regulatory domain changed to country: US
[ 9.150000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.160000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.160000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.170000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.180000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.190000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 200 mBm)
[ 9.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.260000] PPP generic driver version 2.4.2
[ 9.410000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.520000] NET: Registered protocol family 24
[ 9.540000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.550000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.550000] ehci-platform ehci-platform: new USB bus registered, assigned busnumber 1
[ 9.590000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.610000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.610000] hub 1-0:1.0: USB hub found
[ 9.610000] hub 1-0:1.0: 1 port detected
[ 9.640000] nf_conntrack version 0.5.0 (458 buckets, 1832 max)
[ 9.880000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 12.850000] device eth0 entered promiscuous mode
Iwould be verry happy if someone on this board is kind enough to guide me step by step how to unbrick my router.
Im running Windows 7 or XP (whatever goes better with unbricking router)