OpenWrt Forum Archive

Topic: eth0 brdge disconnected of others Ports = no acces to WRT [on progres]

The content of this topic has been archived on 5 May 2018. There are no obvious gaps in this topic, but there may still be some posts missing at the end.

Hi,

I'm a newbee,

I have a Linksys WRT350N v2

I have installed OpenWRT on it and it was working well

I have add a new bridge with Eth0 to test and understand how it works

I have suppress it ............

- Result (If i understand well)
All ports using eth0 to talk togethers stop working

I can see WIFI signal
and i can logg in with wep key i have set at start

but when i hit WRT IP in web brower, no way to acces web interface
same result if i try to connect it by RJ45

I need your help to reverse the situation

Thank you by advance

(Last edited by wrtcfw on 6 Oct 2012, 10:08)

if some one can tell me how reset to openwrt factory setting with my WRT350N v2

it well be appreciate

serge, thank you for your post

i don't know if the linked procedure can be used in my case

******************************************************

in // i find and use an other way to try getting back to normal configuration

1°/ First i find here this message here in this thread page 21
https://forum.openwrt.org/viewtopic.php … 830#p94830

with all needed and a Procedur, Software and RecoveryFirmware to be used !
but the Pb was that at the end i was still unable to logg'into WRT by IP
(maybe the IP of the rooter in the Firmware Linked was not 192.168.1.1, i try several IP without success)



2°/ Then i find the OpenWRT wiki page here http://wiki.openwrt.org/toh/linksys/wrt350nv2
that describ the same procedure named "Flashing and Recovery Methods" by "Download Mode"
and as linked in the Wiki page
i used the openwrt-wrt350nv2-squashfs-recovery.bin CFW as linked to achieve unbrick my WRT350-N v2
that alow me to Logg'Into WRT350N v2 using the stadard IP 192.168.1.1

Now my Pb is to find a way to Upgarde to the CFW file openwrt-wrt350nv2-squashfs-webupgrade.img
that i have installed at the begening before i've "brick" the WRT350 by mystake ......

at start thete is the LINKSYS Firmware and i use the "squashfs webupgrade.img" from WEB GUI of the Linksys OFW

and when I try update it with openwrt-wrt350nv2-squashfs-webupgrade.img file
from the Web GUI of the Recovery CFW that i used (dowloaded as linked)

no success, I've got error message regarding the OpenWRT file compatibility

when i try to use openwrt-wrt350nv2-squashfs-webupgrade.img file
of the openwrt-wrt350nv2-squashfs-webupgrade.img file ?

to be continue

PS : i also find this thread were some links are listed but it is just for information
https://forum.openwrt.org/viewtopic.php?id=23743

(Last edited by wrtcfw on 6 Oct 2012, 11:37)

what are the difference between

CFW openwrt-wrt350nv2-squashfs-webupgrade.img
and
CFW openwrt-wrt350nv2-squashfs-recovery.bin (the one who running now in my rooter)

At first (if i remember well)
i was using/running CFW openwrt-wrt350nv2-squashfs-webupgrade.img

I note that they don't have the same GUI

and if i'm not wrong the "recovery.bin" one is less powerfull than "webupgrade.img" CFW

can some one confirme me it please

(Last edited by wrtcfw on 6 Oct 2012, 11:38)

I start with this GUI

Before i've make a wrong action and brick acces to my WRT350Nv2

http://imageshack.us/a/img32/9535/brlaneth0lan1lan2lan3la.jpg

and now after fallowing recovery procedur

i've got this GUI

http://imageshack.us/a/img849/7503/backfirerecoverycfw.jpg

The discussion might have continued from here.